Home

User Manual

1. Figure 5 3 Figure 5 4 REMOTE Zoom Tele Wide A D KEY GND Focus Far Near COM DC12V IN Figure 5 5 A CAUTION Do not simultaneously connect to the DC 12V IN Jack from the power source connector and the DC 12V IN from the 6 pin Mini DIN connector as error may occur 1 Power Input DC 12V 10 Recommendation 12V 0 5V Max 4 1W 2 Video Output Composite Video 1 Vp p 75 Ohms BNC 3 Audio Output 2Vp p 50 Ohms 4 5 Keys Control Name Function Tele A Zoom Tele or Up A Wide W Zoom Wide or Down V Near 4 Focus Near or Increase Far Focus Far or Decrease Menu Enter or Exit Setup Menu 5 Remote Control Interface 6 Pin Circular Connector refer to figure 5 5 Name IO Note Zoom Tele Wide Input 6V 3V 13V 3V 13V Focus Far Near Input 6V 3V 13V 3V 13V COM Pair Ground for Zoom Focus A D Key Input A D Voltage Divide Control GND Pair Ground for Power Supply and A D Key DC 12V IN Input Power Supply DC 12V 10 Recommendation 12V 0 5V There are Menu Tele Wide Near Far and On Off signals via A D key 6 Camera Control 2 4K 4 8K 9 6K 19 2K BPS Please refer to OSD setup MENU Optional RS 422 RS 485 refer to figure 5 3 Name Function R R T T Use For RS 422 RS 485 Control Optional RS 232
2. 59 10 SPECIFICATIONS Image Device Sony 1 4 Colour Ex View CCD Total Pixels No 795 H x 596 V 470K Effective Pixels No 752 H x 582 V 440K Resolution 550 TVL S N Ratio More than 48 dB Lens Information 3 6 to 126 0mm Auto Iris 35x Optical Zoom Min Shooting Distance 0 01m WIDE 1 5m TELE Minimum Illumination 0 01 Lux 0 Lux with IR Digital Zoom Ratio Basic x 16 Total Zoom Ratio x560 x2 x16 Variable Sync System Internal On Screen Display OSD On Menu Zoom Focus WBC BLC Shutter CAM ID User Title Off Video Output Composite Video 1 Vp p 75 Ohms BNC Audio output 2 Vp p 50 Ohms Camera Control Optional RS 422 RS 485 or RS 232 2 4K 4 8K 9 6K 19 2K BPS Protocol AUTO NATIVE PELCO LG Zoom Speed 8 Sec Mode 11 Sec Mode 14 Sec Mode Focus Mode Auto Manual Push Auto Brightness Control Manual Brightness Up Down White Balance Auto Hue Indoor Outdoor Manual Push Auto Iris Control Auto Manual Iris Up Down AGC Control Auto Manual 1 dB 26 dB Control Day Night Mode AE SENSOR Day Night External Shutter Speed 1 50 1 30 000 Sec 29 Steps Flickerless Mode Off On 1 120 Sec Shutter Set Back Light Comp On Auto Center Up Down Left Right Super Off Negative Positive Negative On Off Wide Burst On Off Zoom Focus Preset 128 Presets Store with Internal EEPROM Remote Control 6 Pin Circular Connec
3. 1 Mount the camera on the mounting bracket by using the hole on the top or bottom of the camera or by using the enclosed 8mm mounting block furnished by 2 screws 2 Connect the Video Output to the monitor or other video device via a 75 Ohms type coaxial cable 3 Connect the power source using the DC Jack 12V DC in the jack center or Remote Control Interface 6 Pin Circular Connector Do not simultaneously connect to the DC 12V IN Jack from the power source connector and the DC 12V IN from the 6 pin Mini DIN connector as error may occur 4 Wait a while for the camera to power on and the zoom lens will resume to the previous power on position automatically 5 Once the picture appears on the monitor press the Zoom Tele Zoom Wide Focus Near Focus Far and Setup Menu Key to obtain the best picture quality 7 1 Native Keyboard Operation Normal Display Mode Native Keyboard Camera Function BRIGHTNESS Brightness BRIGHTNESS Brightness NEAR Focus Near FAR Focus Far Zoom TELE Zoom Tele Zoom WIDE Zoom Wide Move Joystick Left None Move Joystick Right None Move Joystick Up None Move Joystick Down None Camera Function Native Keyboard Accessing Main Menu Press the MENU key Enter preset number 1 128 and press GO COND Me CeO PRESET to put camera in preset A To program position camera enter desired Setting the Preset Points preset number 1 128 and press SET
4. 2 FPL Lower data of position value for the Focus lens Ex Memorize 0x21F to the Focus Lens Position in PRESET 3 OxC5 0x4A PRE I FH FPL CAM ID C S 0xC5 Ox4A 0x32 Ox1F CAM ID C S Memorize Digital Zoom Position for External PRESET control Memorize the Digital Zoom position into the volatile Buffer RAM designated Buffer RAM Index for the external PRESET Move control PC Camera 0xC5 Ox4B PRE I DZP CAM ID C S 31 Camera PC OxC5 Ox4B PRE I DZP PRE I OxXX OxXX OxXX C S 1 PRE_I The index value of Buffer RAM to store the position of the Digital Zoom for the PRESET mode Bit No Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bitl BitO Description Buffer RAM Index 0 7 2 DZP Digital Zoom position Ex Memorize 0x20 to the Digital Zoom Position in PRESET 0 0xC5 Ox4B PRE I DZP CAM ID C S O0xC5 Ox4B 0x00 0x20 CAM ID C S Non Zoom Tracking External PRESET Move Control Move the Zoom and Focus lens to each position and set the Digital Zoom ratio according to data memorized in PRESET Buffer RAM designated INDEX PC Camera 0xC5 Ox4D INDEX 0x00 CAM ID C S Camera PC 0xC5 Ox4D INDEX 0x00 INDEX OxXX OxXX OxXX C S INDEX Position setting index of the PRESET Buffer RAM to change Zoom Focus amp Digital Zoom position Caution The range of INDEX is from 0x00 to 0x07 Camera RESTART Restart the Camera s micro controller u COM PC Camera OxC5 Ox4F 0x00 0x00 CAM
5. Exit the AE set of OSD menu and return to the main menu 22 SPECIAL SET USER TITLE SET This function is for setting up user title on screen display Set the position of title using Near Far Command set the data using Tele Wide Command SHARPNESS ADJUST Set Adjust the level from 0 to 15 MIRROR Set Select the mode ON or OFF This function applies only to high resolution This function is only available when the Digital Zoom Mode is OFF NEGATIVE Set This mode is to change color and luminance to negative Select the mode ON or OFF WIDE BURST Set This mode is to change color burst width for long distance application Select the mode ON or OFF INITIAL SET If initial mode set to ON All SPECIAL function is changed to the factory setting RETURN TO MAIN MENU Exit the SPECIAL set of OSD menu and return to the main menu 23 F OSD SET FUNCTION DISP ON or DISP OFF There are Focus Mode Back Light Shutter Speed and WBC Mode in the function display CAMERA ID DISP ON or DISP OFF ZOOM MAG DISP ON or DISP OFF USER TITLE DISP ON or DISP OFF INIT TITLE DISP ON or DISP OFF BRIGHTNESS DISP ON or DISP OFF DAY NIGHT SET DAY NIGHT MODE SET This function is used for Day amp Night control mode setting Setthe mode to AE Mode SENSOR mode Day mode Night mode or External mode If manual IRIS or manual AGC is selected you cannot set
6. ID C S Camera PC OxC5 Ox4F 0x00 0x00 0x00 OxXX OxXX OxXX C S Digital Zoom Power Adjust Adjust Digital Zoom Max Power PC Camera 0xC5 0x52 INDEX 0x00 CAM ID C S 32 Camera PC 0xC5 0x52 INDEX 0x00 INDEX OxXX OxXX OxXX C S INDEX Index value for setting up Max Power Digital Zoom 1 9 CO cR cO tr Gar F9 In case of INDEX 0 the Max Power Digital Zoom 2X Therefore Total Zoom 70X In case of INDEX 1 the Max Power Digital Zoom 3X Therefore Total Zoom 105X In case of INDEX 2 the Max Power Digital Zoom 4X Therefore Total Zoom 140X In case of INDEX 3 the Max Power Digital Zoom 5X Therefore Total Zoom 175X In case of INDEX 4 the Max Power Digital Zoom 6X Therefore Total Zoom 210X In case of INDEX 5 the Max Power Digital Zoom 7X Therefore Total Zoom 245X In case of INDEX 6 the Max Power Digital Zoom 8X Therefore Total Zoom 280X In case of INDEX 7 the Max Power Digital Zoom 9X Therefore Total Zoom 315X In case of INDEX 8 the Max Power Digital Zoom 10X Therefore Total Zoom 350X In case of INDEX 9 the Max Power Digital Zoom 11X Therefore Total Zoom 385X In case of INDEX 10 the Max Power Digital Zoom 12X Therefore Total Zoom 420X In case of INDEX 11 the Max Power Digital Zoom 13X Therefore Total Zoom 455X In case of INDEX 12 the Max Power Digital Zoom 14X Therefore Total Zoom 490X In c
7. amp Night Index OxXX OxXX OxXX C S Day amp Night y 8 Data Explanation Index The SENSOR level is setting up threshold for turning the filter according to 0x00 RENSOR LENE sensitivity of SENSOR 0x01 FILTER DELAY Delay time for turning the filter Other Values No Operation Read Day amp Night Data This command is to see the camera s Day amp Night data PC Camera 0xC5 OxFO Day amp Night Index 0x00 CAM ID C S Camera PC 0xC5 OxFO Day amp Night Index 0x00 Data OxXX OxXX OxXX C S Day amp Night y 8 Data Explanation Index The SENSOR level is setting up threshold for turning the filter according to ous apne pete sensitivity of SENSOR 0x01 FILTER DELAY Delay time for turning the filter Other Values No Operation 57 9 3 Key Code Table Key Variable SY Description Code KN NOT 0x00 No key function will operate KN TELE Sont Perform Zoom Tracking to TELE side by slow speed In case of displaying the MENU it operates as the MENU selection scroll up Perform Zoom Tracking to TELE side by high speed In case of KN_HTELE 0x02 displaying the MENU it operates as the MENU selection scroll up Perform Zoom Tracking to WIDE side by slow speed In case of KN WIDE 0x03 displaying the MENU it operates as the MENU selection scroll down Perform Zoom Tracking to WIDE side by high speed I
8. e qwision CCTV Model PCC435 Colour Digital CCD 560x Zoom Camera C Before you begin 9 Please unpack the box carefully and identify that all the parts are present 9 Do not open the camera housing This will void the warranty and break the warranty seal inside the camera 9 Make sure you use only the recommended power supply Damage caused to the camera by incorrect voltage or wiring Is not covered by the warranty Model PCC435 Colour Digital CCD 560x Zoom Camera CONTENTS I SAEETY PRECAUTIONS c iyssestreesd inh iv eno ei vi ense e a a e 3 2 INTRODUCTION ee etusa thon EPI RASA INED EA AI UR peXE es ITE Dna EN RP RI TR essaies sE 4 S FEATURES jarse eins hh eeu voa RUN pA CX Re REY a RUN Gore a aon a eU NUR PA 5 A ACCESSORIES ero 6 5 NAME and FUNCTION of EACH PART cciecsecsscivscendevsssssavceasesussteseetedeasestsesssasneusactsenntvadeseds 7 6 INSTA LEA PION mr essais eas s ianen eenas So retai ons sE ar eeoa esa 10 6 1 Native Keyboard Installation ss eerie eiecit ses eras tunes sa dasaeeasdnead HERE USA TUUS ERR e YS Qoae deve da 11 6 2 PELCO Keyboard or compatible Installation eese IT 7 OPERATING PROCEDURE coco teat RS ehe dore o rele b eee M Node ERR OC eu osese PIS pP ete ana Pete oo 12 TL Native Keyboard Operation eder con Date eau Qe eines pax terea petiuit 12 7 2 PELCO Keyboard or compatible Operation essere ene 13 S SYSTEM SETUP vonese
9. High Resolution Color CCD Camera e Supports powerful function Auto Iris Control AIC Auto White Balance AWB Auto Gain Control AGC Auto Back Light Compensation ABLC Flickerless FL and Auto Focus AF e 35x Optical Zoom Lens and 16x Digital Zoom Total 560x Zoom e Day amp Night time vision with IR Cut Filter change mechanism including Day Night Control Interface On Screen Display OSD Setup Menu Camera Control via either RS 422 RS 485 or RS 232 e Supports PELCO D and P LG Protocol Wire Remote Control 6 Pin Circular Connector including wet contact interface to control zooming and focusing and A D Key Control for Menu Tele Wide Near Far and On Off signals e Built in 5 keys to Control Zooming and Focusing Function and Setup Menu adjustment Built in Audio 4 ACCESSORIES Mounting Block x1 and Screws x2 User s Manual x1 5 NAME and FUNCTION of EACH PART Front View Side View i 126 1 mm 20 5 mm 64 mm 20 5 mm 73 mm 30 5 mm i i B r 3 Ti i HN NO OO j h m Figure 5 1 Figure 5 2 Rear View VIDEO AUDIO REMOTE DC 12V IN DC 12V IN z Dno
10. PRESET Press the AUTO FOCUS Key the LED of the AUTO FOCUS lights up and press ADTOPOCUPICODIEUE AUTO FOCUS key again to disable the function 12 OSD Setup Menu Mode Native Keyboard Camera Function lt Decrease gt Increase A Cursor Up v Cursor Down BRIGHTNESS None BRIGHTNESS None NEAR None FAR None Zoom TELE None Zoom WIDE None Move Joystick Left None Move Joystick Right None Move Joystick Up None Move Joystick Down None Please refer to the native keyboard manual for more information 7 2 PELCO Keyboard or compatible Operation Normal Display Mode PELCO Keyboard Camera Function OPEN Brightness CLOSE Brightness NEAR Focus Near FAR Focus Far Twist Joystick clockwise or Zoom In Zoom Tele Twist Joystick counterclockwise or Zoom Out Zoom Wide Move Joystick Left None Move Joystick Right None Move Joystick Up None Move Joystick Down None Camera Function PELCO Keyboard Accessing Main Menu Enter 95 press on the PRESET button approximately five seconds until the main menu appears on the screen Call up the Preset Points Enter preset number 1 32 35 82 and press PRESET to put the camera in preset position Setting the Preset Points To program position camera enter desired preset number 1 32 35 82 and press on the PRESET button for two seconds OSD Se
11. AE mode to Day amp Night control mode SENSOR LEVEL Set Adjust the level from 0 to 255 The SENSOR level threshold is used for filter setting setup result is reflected according to the sensitivity of the SENSOR FILTER DLY Set Adjust the level from 1 to 15 seconds Delay time for turning the filter The function is valid to SENSOR mode INITIAL SET If initial mode set to ON All DAY NIGHT function is changed to the factory setting RETURN TO MAIN MENU Exit the DAY NIGHT set of OSD menu and return to the main menu 24 COMMUNICATION SET Adjusted communication function is only effective after exiting the OSD setup menu Protocol Set Speed Set and Parity Set should only be adjusted via rear panel keys CAMERA ID To connect numerous cameras identification number is assigned to each camera for camera control 000 255 total numbers of ID are 256 ID 1 127 for native keyboard ID 0 253 for PELCO P protocol ID 1 255 for PELCO D protocol PROTOCOL SET Setthe mode to AUTO NATIVE PELCO or LG Camera automatically detects the type of PELCO Protocol No extra settings are required to set D and P Protocols SPEED SET Set the speed to 2400 4800 9600 or 19200 PARITY SET Setthe parity to NONE ODD or EVEN INITIAL SET Set the initial set mode to ON AII functions are changed to the factory setting excluding communication function EXI
12. COMM BBBB P D S monitor for a short interval Indicate the camera stand by during the 5 2 STAND BY MODE STAND BY camera s power turning ON Dx560 Digital Zoom mode 6 ZOOM DISPLAY X35 Optical Zoom mode According to the identification number 000 255 for each 7 CAMERA ID e l MT camera multi point control via PC or keyboard is valid USER TITLE STRING Maximum 10 user char string BRIGHTNESS Brightness data 16 NOTE Setting string BBBB P D S BBBB represent baud rate it can be one of the following values 2400 4800 9600 19200 P represent parity it can be one of the following values N None O Odd E EVEN D represent data bits it should be the following value 8 S represent stop bit it should be the following value 1 For example the following string specifies a baud rate of 9600 no parity 8 data bits and stop bit 9600 N 8 1 17 8 2 MENU DESCRIPTIONS MAIN MENU MENU FOCUS SET 1 gt AWB SET er AE SET gt SPECIAL SET ic F OSD DISP e gt DAY NIGHT e gt COMMUNICAT e gt INITIAL SET ON EXIT gt Figure 8 2 SET UP THE MENU In order to display the Setup Menu on the screen set the Menu command or press key panel To select each item by using the Zoom Tele and Zoom Wide command or using the Up A and Down V key panel To change the data by using the Focus Far and Focus Near command or by using the Decrease and Incr
13. HCW300 The Xvision HCW300 allows industry standard CCTV cameras to be wall mounted externally in temperatures from 20 to 50 C The built in fan and heater maintain a temperature of 25 C inside the housing and to protect the camera cabling the bracket features cable management so no cables are exposed Professional weatherproof IR LED housing and wall bracket with built in Heater and Fan Cable Managed Model HCW300IR The Xvision HCW300IR allows traditional cameras to be wall mounted 1 externally in temperatures from 20 to 50 C The integrated IR LEDs allow for up to 30 metres Nightvision The built in fan and heater maintain a temperature of 25 C inside the housing and to protect the camera cabling the bracket features cable management so no cables are exposed 61 e wision CCTV TECHNICAL SUPPORT For Technical Support for any Xvision product please contact your local distributor LIMITED WARRANTY This product is supplied with a limited 3 Year warranty The Warranty excludes products that have been misused including accidental damage and damage caused by normal wear and tear In the unlikely event that you encounter a problem with this product it Should be returned to the place of purchase Manufactured exclusively for Xvision Europe Group Head Office London U K Email info x vision co uk Web www x vision co uk
14. In this case the target zoom position value is memorized in the internal nonvolatile memory And the memory position is indicated by the INDEX value PC Camera 0xC5 Ox7E INDEX 0x00 CAM ID C S Camera PC OxC5 Ox7E INDEX 0x00 INDEX OxXX OxXX OxXX C S 47 INDEX The value for indicating the memory position to store the zoom focus and digital Zoom position value The range of this value is from 0x00 to Ox7F Focusing Object Distance Setting Set the object distance range PC Camera OxC5 0x58 Distance 0x00 CAM ID C S Camera PC OxC5 0x58 Distance 0x00 Distance OxXX OxXX OxXX C S Distance The value for indicating the object distance range limit that the camera can be focused 1 In case of 0x00 2 Incase of 0x01 3 Incase of 0x02 4 Incase of 0x03 5 Incase of 0x04 6 Incase of 0x05 7 Incase of 0x06 8 Focusing range From 1 cm To infinite Focusing range From 10 cm To infinite Focusing range From 50 cm To infinite Focusing range From 1 m To infinite Focusing range From 3 m To infinite Focusing range From 5 m To infinite Focusing range From 10 m To infinite In case of every other value The focusing range remains unchanged Focus Lens FAR Direction Step Move Command This command moves the focus lens by a specific step number in the direction of FAR Caution This command is performed when the focus mode is MANUAL o
15. OxAA 0xA5 0x00 CAM ID C S Camera PC OxC5 OxAA 0xA5 0x00 R Cont OxXX OxXX OxXX C S R Cont The value which is currently assigned to the red control gain of the camera There is some tolerance between read value and adjust value Blue Control Gain Adjust Command This command adjusts the blue control gain of the camera PC Camera 0xC5 OxAA 0xA6 B Cont CAM ID C S 52 Camera PC OxC5 OxAA 0xA6 B Cont OxA6 OxXX OxXX OxXX C S B Cont The value which adjusts the blue control gain of the camera Blue Control Gain Read Command This command reads the current blue gain of the camera PC Camera 0xC5 OxAA 0xA7 0x00 CAM ID C S Camera PC OxC5 Ox AA OxA7 0x00 B Cont OXXX OxXX OxXX C S B Cont The value which is currently assigned to the blue control gain of the camera There is some tolerance between read value and adjust value MOSAIC Digital Effect On Off control Command This command switches the MOSAIC digital effect mode to ON or OFF according to ONOFF PC Camera 0xC5 0xAA 0xA8 ONOFF CAM ID C S Camera PC OxC5 OxAA OxA8 ONOFF 0xA8 OxXX OxXX OxXX C S 1 In case of ONOFF 0x00 the MOSAIC digital effect mode becomes OFF mode 2 Incase of ONOFF 0x01 the MOSAIC digital effect mode becomes ON mode 3 Incase of ONOFF every other value the MOSAIC digital effect mode remains unchanged The Object Distance Range Data Read Command This command reads the object distance ran
16. Zoom Lens Position for External PRESET control Memorize the Zoom lens position into the volatile Buffer RAM designated Buffer RAM Index for the external PRESET Move control PC Camera 0xC5 0x49 PRE I ZH ZPL CAM ID C S Camera PC OxC5 0x49 PRE I ZH ZPL PRE I ZH OxXX OxXX OxXX CS 30 1 PRE I ZH The index value of the Buffer RAM to store the position of the Zoom lens for the PRESET mode and the upper data of position value for the Zoom lens Bit No Bit7 Bit6 Bit5 Bit 4 Bit3 Bit2 Bit1 BitO Description Buffer RAM Index 0 7 Upper data of Zoom lens position 2 ZPL Lower data of position value for the Zoom lens Ex The position of Zoom Lens to memorize 0x126 amp The index of Buffer RAM for PRESET 2 0xC5 0x49 PRE I ZH ZPL CAM ID CS O0xC5 0x49 0x21 0x26 CAM ID C S Memorize Focus Lens Position for External PRESET control Memorize the Focus lens position into the volatile Buffer RAM designated Buffer RAM Index for the external PRESET Move control PC Camera OxCS Ox4A PRE I FH FPL CAM ID C S Camera PC OxC5 0x4A PRE I FH FPL PRE I FH OxXX OxXX OxXX C S 1 PRE I FH The index value of Buffer RAM to store the position of the Focus lens for the PRESET mode and the upper data of position value for the Focus lens Bit No Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bitl Bit 0 Description Buffer RAM Index 0 7 Upper data of Focus lens position
17. be achieved during the night please install appropriate light fixtures If any abnormal operation or accident occurs disconnect the device and contact your dealer or the nearest service center Do not simultaneously connect to the DC 12V IN Jack from the power source connector and the DC 12V IN from the 6 pin Mini DIN connector as error may occur 2 INTRODUCTION The auto focus camera is a compact CCTV camera designed for easy integration into surveillance systems The Camera s built in 35x Optical zoom lens spells added user convenience since there is no need for separate adjustment of the focal distance Current applications include highway traffic control plus security surveillance in such locations as elevators and parking lots The advanced DSP technology allows intelligent control for clearer detailed pictures Additionally the user can perform remote Zoom Focus Iris White Balance operations via either RS 422 RS 485 or RS 232 optional interface In combination with a highly sensitive Sony 1 4 Ex View CCD sensor these features make the auto focus camera is particularly suitable for surveillance e Built in Optical Zoom Lens with Digital Zoom The built in 35x optical zoom lens is highly reliable and offers auto focus and auto iris functions The camera also includes 16x digital zoom for a maximum of 560x combined optical and digital zoom e Day amp Night ICR function provides change from color to B W mode auto
18. of a CAMERA 2 On Off The On Off mode of the camera ID 0x00 Camera ID is OFF mode OxFF Camera ID is ON mode Auto Back Light Mode ON OFF control Change the Auto Back Light Mode of camera PC Camera 0xC5 0xAA 0x6D MODE CAM ID C S Camera PC OxC5 OxAA 0x6D MODE 0x6D OxXX OxXX OxXX C S 1 In case of MODE 0x00 the Auto Back Light Mode of camera becomes OFF mode In this case the camera key controls Back Light ON OFF manually 2 In case of MODE 0x01 the Auto Back Light Mode of the camera becomes ON mode Then Back Light ON OFF is controlled automatically depending on the status of the scene 3 In case of MODE every other value the Auto Back Light Mode of camera remains unchanged 34 BACKLIGHT ON OFF control Switch the BACKLIGHT mode to On Off according to the data of MODE PC Camera 0xC5 OxAA 0x70 MODE CAM ID C S Camera PC OxC5 OxAA 0x70 MODE 0x70 OxXX OxXX OxXX C S 1 Incase of MODE 0x01 The BACKLIGHT mode becomes ON mode 2 In case of MODE 0x00 The BACKLIGHT mode becomes OFF mode Otherwise The BACKLIGHT mode is not changed Caution In this case the Auto Back Light mode is released automatically 100 NEGATIVE ON OFF control Switch the 100 NEGATIVE mode to On Off according to the data of MODE PC Camera 0xC5 OxAA 0x72 MODE CAM ID C S Camera PC OxC5 OxAA 0x72 MODE 0x72 OxXX OxXX OxXX C S 1 Incase of MODE 0x01 the 100 NEGATIVE mode b
19. Adjust the level from 0 MIN to 99 MAX RED GAIN SET This function is valid for Manual WB mode This mode is an optional adjustment function for users to adjust special colors BLUE GAIN SET This function is valid for Manual WB mode This mode is an optional adjustment function for users to adjust special colors PUSH AUTO SET This function is valid for Push Auto WB mode Turn this mode ON the white trace automatically Turn this mode OFF Preserve the white of final auto tracing action Manual INITIAL SET If initial mode set to ON All AWB function is changed to the factory setting RETURN TO MAIN MENU Exit the AWB set of OSD menu and return to the main menu 20 AE SET AE MODE SET This function is for changing the AE mode Setthe mode to AUTO IRIS MAN AGC MAN or Manual IRIS ADJUST SET This function is valid for IRIS MAN mode Adjust the level from 36 MIN to 250 MAX AGC MAXIMUM SET AGC ADJUST SET This function is valid for AGC AUTO mode AGC MAN mode AGC AUTO means AUTO or IRIS MAN Adjust the level from 28 MIN to 255 MAX BRIGHTNESS ADJUSTMENT SET Adjust the level from 0 MIN to 99 MAX BACKLIGHT SET Setthe mode to OFF ON AUTO or SUPER Back Light Compensation BLC is ON BLC could emphasize the luminance of the BLC Area according to the BLC Level AUTO BLC When a back light condition occurs in a
20. Digital Zoom Mode is changed to ON mode 2 In case of MODE 0x00 the Digital Zoom Mode is changed to OFF mode 3 Otherwise the Digital Zoom Mode remains unchanged SCREEN INVERSION FULL MIRROR ON OFF Setting Switch the SCREEN INVERSION mode to ON or OFF according to the data of MODE PC Camera 0xC5 OxAA 0x7F MODE CAM ID C S Camera PC OxC5 OxAA Ox7F MODE Ox7E OxXX OxXX OxXX CS 1 In case of MODE 0x01 The SCREEN INVERSION Mode is changed to ON mode In this case The Screen is reversed 2 Incase of MODE 0x00 The SCREEN INVERSION Mode is changed to OFF mode 3 Otherwise the SCREEN INVERSION Mode remains unchanged Caution This command is valid when the Digital Zoom Mode is OFF Slow Speed Zoom Tracking External PRESET Move Control Performs Zoom Tracking PRESET action to the targeted zoom position memorized in the volatile PRESET Buffer RAM indicated by the INDEX value In this case the Zoom Tracking is performed slowly PC Camera 0xC5 0x7B INDEX 0x00 CAM ID C S Camera PC 0xC5 Ox 7B INDEX 0x00 INDEX OxXX OxXX OxXX C S INDEX The index value of the PRESET Buffer RAM taking the target Zoom position Caution The range of the INDEX is from 0x00 to 0x07 40 High Speed Zoom Tracking External PRESET Move Control Performs Zoom Tracking PRESET action to the targeted zoom position memorized in the volatile PRESET Buffer RAM indicated by the INDEX v
21. Explanation of DZ MAX data DZ MAX Explanation 0x2 The current Max Power Digital Zoom of the Camera is x2 0x3 The current Max Power Digital Zoom of the Camera is x3 0x4 The current Max Power Digital Zoom of the Camera is x4 0x5 The current Max Power Digital Zoom of the Camera is x5 0x6 The current Max Power Digital Zoom of the Camera is x6 0x7 The current Max Power Digital Zoom of the Camera is x7 0x8 The current Max Power Digital Zoom of the Camera is x8 0x9 The current Max Power Digital Zoom of the Camera is x9 OxA The current Max Power Digital Zoom of the Camera is x10 OxB The current Max Power Digital Zoom of the Camera is x11 OxC The current Max Power Digital Zoom of the Camera is x12 OxD The current Max Power Digital Zoom of the Camera is x13 OxE The current Max Power Digital Zoom of the Camera is x14 OxF The current Max Power Digital Zoom of the Camera is x15 0x10 The current Max Power Digital Zoom of the Camera is x16 Memorize Internal PRESET Position for Internal PRESET control Memorize the current zoom focus and digital zoom position value into the internal nonvolatile memory of the CAMERA for controlling the Internal PRESET Move The memory position to store is indicated by the INDEX value PC Camera 0xC5 0x79 INDEX 0x00 CAM ID C S Camera PC 0xC5 0x79 INDE
22. IGHT Level Read Read the current BACKLIGHT level of Camera PC Camera OxC5 OxAA 0x61 0x00 CAM ID C S Camera PC OxC5 OxAA 0x61 0x00 BL level OxXX OxXX OxXX C S BL level This is a value of the camera for controlling BACKLIGHT level Adjust BACKLIGHT level Adjust current BACKLIGHT level of Camera PC Camera 0xC5 OxAA 0x62 BL level CAM ID C S Camera PC OxC5 OxAA 0x62 BL level 0x62 OxXX OxXX OxXX C S BL level This is a value to adjust BACKLIGHT level of camera White Balance Mode Setting Set the mode of White Balance according to WB CNT PC Camera 0xC5 OxAA 0x65 WB CNT CAM IDC S Camera PC OxC5 OxAA 0x65 WB CNT 0x65 OxXX OxXX OxXX C S WB CNT This is an index counter to change the mode of White Balance In case of WB CNT 0 the mode of White Balance becomes AUTO mode In case of WB CNT 1 the mode of White Balance becomes HUE mode In case of WB CNT 2 the mode of White Balance becomes INDOOR mode In case of WB CNT 3 the mode of White Balance becomes OUTDOOR mode In case of WB CNT 4 the mode of White Balance becomes MANUAL mode In case of WB CNT 5 the mode of White Balance becomes PUSH AUTO mode a ON Or ipe Nor or In case of WB_CNT every other value the mode of White Balance remains unchanged 28 Camera ID Display Mode ON OFF Toggle control Switch the display mode of camera ID ON OFF PC Camera 0xC5 O
23. NDOOR White Balance mode 0x3 OUTDOOR White Balance mode 0x4 MANUAL White Balance mode 0x5 PUSH AUTO White Balance mode Read the Exposure Mode Read the current Exposure Mode of the camera The data is AE_MODE PC Camera 0xC5 OxAA 0x84 0x00 CAM ID C S Camera PC OxC5 OxAA 0x84 0x00 AE MODE OxXX OxXX OxXX C S Explanation of AE MODE data 43 AE MODE Explanation 0x0 AUTO Exposure mode 0x2 IRIS MAN Exposure mode 0x3 AGC MAN Exposure mode 0x4 MANUAL Exposure mode Read the current MWB CTL data at the Hue White Balance Mode Read the current HUE point adjust data of the Camera at the Hue White Balance Mode The return data is MWB_CTL PC Camera 0xC5 OxAA 0x87 0x00 CAM ID C S Camera PC OxC5 OxAA 0x87 0x00 MWB CTL OxXX OxXX OxXX C S Read the current SHARPNESS data Read the current SHARPNESS data of the camera The data is Sharpness PC Camera OxCS OxAA 0x88 0x00 CAM ID C S Camera PC 0xC5 OxAA 0x88 0x00 Sharpness OxXX OxXX OxXX C S Read the current BRIGHTNESS data Read the current BRIGHTNESS data of the camera The data is Brightness PC Camera 0xC5 OxAA 0x89 0x00 CAM ID C S Camera PC OxC5 OxAA 0x89 0x00 Brightness OXXX OxXX OxXX C S Read the current Shutter Speed Control counter value Read the current counter value to control Shutter Speed The data is SSC_CNT PC Camera 0xC5 OxAA 0x8A 0x00 CAM ID C S Came
24. SD Sub Menu OSD is displayed In case of INDEX 0x05 or gt 0x06 the Menu OSD is erased heme IE eS ee Camera ID Function OSD Display Mode On Off Setting Command This Command decides whether or not the Camera ID Function OSD is to be displayed on the screen PC Camera OxC5 OxAA 0x96 OnOff CAM ID C S Camera PC OxC5 OxAA 0x96 OnOff 0x96 OxXX OxXX OxXX C S 49 1 Incase of INDEX 0x00 the Camera ID Function OSD is not displayed 2 Incase of INDEX 0x01 the Camera ID Function OSD is displayed 3 Incase of INDEX every other value No action is performed Each Sub Menu Items Initialization Command This Command initializes all data of each sub menu PC Camera OxC5 OxAA 0x97 INDEX CAM IDC S Camera PC OxC5 OxAA 0x97 INDEX 0x97 OxXX OxXX OxXX C S INDEX This is a value which selects the sub MENU In case of INDEX 0x00 the data of all Sub Menu are initialized In case of INDEX 0x01 the data of Focus Sub Menu are initialized In case of INDEX 0x02 the data of White Balance Sub Menu is initialized In case of INDEX 0x03 the data of Exposure Sub Menu is initialized In case of INDEX 0x04 the data of Special Function Sub Menu is initialized In case of INDEX 0x06 the data of Function OSD Sub Menu is initialized Die pps ops o ES Camera Control Status Register 3 Data Read Command Read the status that the camera is controlled PC C
25. T Exit the OSD menu and enter the normal display Letters in BOLD Default Mode 25 9 Camera Control Command Protocol For RS 232 RS 422 and RS 485 9 1 Communication Format The communication data format from PC to Camera Data of total 6 bytes is transmitted from PC to camera Format Bytel Byte2 Byte3 Byte4 Byte5 Byte6 OxC5 Codel Code2 Code3 CAM_ID CS Description Refer to 9 2 PC Command a Byte 1 Camera realizes the protocol comes from the PC b Byte 2 The data is changeable according to the PC Command c Byte 3 The data is changeable according to the PC Command d Byte 4 The data is changeable according to the PC Command e Byte 5 Camera s ID Identification number to communicate 0 255 It will be impossible to communicate when there s a difference between the value of CAM_ID and the given value of the Camera s ID f Byte 6 The value of Check Sum from Byte 1 to Byte 5 Ex In case of transmission OxC5 Ox5F OxOC 0x00 0x00 OxCS OxSF 0x0C 0x00 0x00 0x130 Therefore C S 0x30 26 The communication data format from Camera to PC Data of total 9 bytes is transmitted from Camera to PC Format Bytel Byte2 Byte3 Byte4 Byte5 Byte6 Byte7 Byte8 Byte9 OxC5 Codel Code2 Code3 Datal Data2 Data3 Data4 C S Description Refer to 9 2 PC Command a Byte 1 Cam
26. UTO White Balance state to ON or OFF at PUSH AUTO White Balance mode according to the data of MODE PC Camera 0xC5 OxAA 0x78 MODE CAM ID C S Camera PC 0xC5 OxAA 0x78 MODE 0x78 OxXX OxXX OxXX C S 1 If MODE 0x01 the PUSH AUTO White Balance state becomes to ON In this case White Balance Tracking is activated 2 If MODE 0x00 the PUSH AUTO White Balance state becomes to OFF In this case White Balance Tracking is stopped 36 3 Otherwise the PUSH AUTO White Balance state remains unchanged Caution This mode will not be saved when the power of a camera turns OFF ON Default mode is OFF mode This command is valid when the White Balance Mode is PUSH AUTO mode SHARPNESS Data Setting Set the sharpness level of the camera according to the data of Sharpness PC Camera 0xC5 OxAA 0x79 Sharpness CAM ID C S Camera PC 0xC5 OxAA 0x79 Sharpness 0x79 OxXX OxXX OxXX C S 1 The data for adjusting sharpness level of the camera 2 Data value range 0x00 OxOF BRIGHTNESS Data Setting Set the brightness level of the camera according to the data of Brightness PC Camera OxC5 OxAA 0x7A Brightness CAM ID C S Camera PC 0xC5 OxAA 0x7A Brightness 0x7A OxXX OxXX OxXX CS Brightness The data for adjusting the brightness level of the camera MENU OSD Display ON OFF Setting Set the MENU OSD Display mode of the camera to ON or OFF according to the data of MODE PC C
27. X 0x00 INDEX OxXX OxXX OxXX C S INDEX The value for indicating the memory position to store the zoom focus and digital Zoom position value The range of this value is from 0x00 to Ox7F 46 Internal Non Zoom Tracking PRESET Moving control Performs the Internal PRESET Moving action When the camera receives this command the zoom focus and digital zoom position is moved to the position memorized in the internal nonvolatile memory of the camera according to INDEX value PC Camera 0xC5 0x7A INDEX 0x00 CAM ID C S Camera PC OxC5 0x7A INDEX 0x00 INDEX OxXX OxXX OxXX C S INDEX The value for indicating the memory position to store the zoom focus and digital Zoom position value The range of this value is from 0x00 to Ox7F Slow Speed Internal Zoom Tracking PRESET Moving control Perform the Zoom Tracking PRESET action to the target zoom position slowly In this case the target zoom position value is memorized in the internal nonvolatile memory And the memory position is indicated by the INDEX value PC Camera 0xC5 0x7D INDEX 0x00 CAM ID C S Camera PC 0xC5 Ox 7D INDEX 0x00 INDEX OxXX OxXX OxXX C S INDEX This is a value for indicating the memory position to store the zoom focus and digital zoom position value The range of this value is from 0x00 to Ox7F High Speed Internal Zoom Tracking PRESET Moving control Performs the Zoom Tracking PRESET action to the target zoom position quickly
28. alue In this case the Zoom Tracking is performed quickly PC Camera 0xC5 0x7C INDEX 0x00 CAM ID C S Camera PC 0xC5 0x7C INDEX 0x00 INDEX OxXX OxXX OxXX C S INDEX The index value of the PRESET Buffer RAM taking the target Zoom position Caution The range of INDEX is from 0x00 to 0x07 Zoom Tracking PRESET status Read Read the status of the Zoom Tracking PRESET action to judge whether the PRESET action has been completed or performed PC Camera 0xC5 Ox7F 0x00 0x00 CAM ID C S Camera PC OxC5 0x7F 0x00 0x00 Status OxXX OxXX OxXX C S l Incase of Status 0x00 the Zoom Tracking PRESET action is complete 2 Incase of Status 0x01 the Zoom Tracking PRESET action is currently performing CAMERA status Read Command 1 Read the current status of the camera The data is CAM CONI PC Camera OxC5 OxAA 0x80 0x00 CAM ID C S Camera PC OxC5 OxAA 0x80 0x00 CAM CONI OxXX OxXX OxXX C S Construction of CAM CONI data 41 Bit Explanation 7 0 Focus Auto state 1 Focus Manual state 6 0 Camera ID OFF mode 1 Camera ID ON mode 5 0 WB Push Auto OFF state 1 WB Push Auto ON state 4 0 BACKLIGHT OFF state 1 BACKLIGHT ON state 3 0 FLICKERLESS OFF state 1 FLICKERLESS ON state 2 0 Focus AUTO MANUAL mode 1 Focus PUSH AUTO mode 1 0 Digital Zoom OFF mode 1 Digital Zoom ON mode 0 Reserved CAMERA status Read Command 2 Read the current stat
29. amera 0xC5 OxAA 0x63 MODE CAM ID C S Camera PC 0xC5 OxAA 0x63 MODE 0x63 OxXX OxXX OxXX C S 1 Incase of MODE 0x01 Main Menu OSD is displayed on the screen 2 Incase of MODE 0x00 MENU OSD is erased on the screen 3 Otherwise no action is performed 37 SHUTTER Speed Setting Set the shutter speed of the camera according to the data of SSC_CNT PC Camera 0xC5 OxAA 0x7B SSC_CNT CAM ID C S Camera PC OxC5 OxAA Ox7B SSC_CNT Ox7B OxXX OxXX OxXX C S SSC CNT NTSC PAL SSC CNT NTSC PAL 0 1 60 1 50 15 1 1100 1 1100 1 1 125 1 125 16 1 1200 1 1200 2 1 150 1 150 17 1 1300 1 1300 3 1 200 1 200 18 1 1500 1 1500 4 1 250 1 250 19 1 1600 1 1600 5 1 300 1 300 20 1 1800 1 1800 6 1 350 1 350 21 1 2000 1 2000 7 1 400 1 400 22 1 2500 1 2500 8 1 450 1 450 23 1 3000 1 3000 9 1 500 1 500 24 1 3500 1 3500 10 1 600 1 600 25 1 4000 1 4000 11 1 700 1 700 26 1 6000 1 6000 12 1 800 1 800 27 1 10000 1 10000 13 1 900 1 900 28 1 30000 1 30000 14 1 1000 1 1000 IRIS OPEN Level Setting Set the IRIS OPEN Level of the camera according to the data of IRIS_CTL PC Camera OxC5 OxAA 0x7C IRIS CTL CAM ID C S Camera PC OxC5 OxAA 0x7C IRIS CTL 0x7C OxXX OxXX OxXX C S IRIS CTL The data for adjusting IRIS level of the camera Data value range from 0x4A Full Close to 0xB3 Full Open Caution This Command is valid when the Expos
30. amera OxC5 OxAA 0x9A 0x00 CAM ID C S Camera PC OxC5 OxAA 0x9A 0x00 CAM CONG3 OxXX OxXX OxXX C S CAM CON This is a status value that the camera is currently controlled Bit Explanation 7 1 High Speed Zoom Tracking Mode 6 1 Normal Speed Zoom Tracking Mode 5 1 Auto Focus Zoom Tracking Mode at MANUAL or PUSH AUTO Focus mode 4 Reserved 3 0 Wide Burst Function OFF mode 1 Wide Burst Function ON mode Reserved Reserved 0 Reserved 50 Zoom Tracking Mode Change Command This command changes the zoom tracking mode according to MODE PC Camera 0xC5 OxAA 0x9B MODE CAM ID C S Camera PC OxC5 OxAA Ox9B MODE 0x9B OxXX OxXX OxXX CS 1 In case of MODE 0x00 the zoom tracking mode becomes MANUAL mode 2 In case of MODE 0x01 the zoom tracking mode becomes AUTO FOCUS mode 3 In case of MODE every other value the zoom tracking mode is not changed Caution This command is valid when the focus mode is MANUAL or PUSH AUTO mode Back Light Control Mode Setting Command This command sets the back light mode of the camera according to MODE PC Camera 0xC5 OxAA 0x9C MODE CAM ID CSS Camera PC OxC5 OxAA 0x9C MODE 0x9C OxXX OxXX OxXX CS In case of MODE 0x00 the back light mode becomes OFF mode In case of MODE 0x01 the back light mode becomes ON mode In case of MODE 0x02 the back light mode becomes AUTO mode In case of MODE 0x03 the back li
31. ase of INDEX 13 Max Power Digital Zoom 15X Therefore Total Zoom 525X In case of INDEX 14 Max Power Digital Zoom 16X Therefore Total Zoom 560X In case of INDEX every other value the Max Power Digital Zoom remains unchanged Key Action Perform the Key action according to the data of KEY NUM Caution After using the Key action Camera has to be notified by stop of key action code KEY NUM KN STOP PC Camera OxC5 Ox5F KEY NUM 0x00 CAM ID C S Camera PC OxC5 0x5F KEY NUM 0x00 KEY NUM 0xXX OxXX OxXX C S KEY NUM This is a Key code value for operation Refer to 9 3 Key Code Table Changing CAM ID Change the data of CAM ID to NEW C ID and Camera ID mode PC Camera 0xC5 0x78 NEW C ID On Off CAM ID C S 33 Camera PC OxC5 0x78 NEW C ID On Off NEW C ID OxXX OxXX OxXX C S 1 NEW C ID New data to change Camera ID 2 On Off Setting the Camera ID mode to On or Off If On Off 0x00 the Camera ID mode becomes OFF mode In this case we may ignore CAM ID value Otherwise the Camera ID mode becomes ON mode Then the value of CAM ID is changed to NEW C ID CAM ID Read Read the data of Camera s ID Caution This command may only be used in condition of one by one connection PC vs CAMERA PC Camera O0xC5 OxCC 0x00 0x00 CAM ID C S Camera PC OxC5 0xCC 0x00 0x00 CAM ID On Off OxXX OxXX C S 1 CAM ID The Camera ID data
32. ative keyboard Connect R and T of the camera together connect R and T of the camera to D of the native keyboard User could adjust Camera ID via rear panel keys or via remote commands Protocol Speed and Parity should only be adjusted via rear panel keys Communication Setting CAMERA ID 1 127 PROTOCOL AUTO NATIVE SPEED 9600 PARITY NONE The speed of native keyboard is fixed 9600 Adjusted function is only effective after exiting the OSD setup menu 6 2 PELCO Keyboard or compatible Installation 1 RS 422 interface is used for communicating PELCO keyboard Refer to Figure 6 2 connect R of the camera to T of the PELCO keyboard Connect R of the camera to T of the PELCO keyboard User could adjust Camera ID via rear panel keys or via remote commands Protocol Speed and Parity should only be adjusted via rear panel keys Communication Setting 0 253 for P protocol CAMERA ID 1 255 for D protocol PROTOCOL AUTO PELCO SPEED 2400 4800 9600 19200 PARITY NONE The speed of camera should be the same as the speed of the keyboard Adjusted function is only effective after exiting the OSD setup menu NOTE Maximum cable distance for RS 422 RS 485 communication over 24 gauge wire is 4 000 feet 1 219 m Recommend using shielded twisted pair cable that meets the basic requirements for EIA RS 422 RS 485 applications 11 7 OPERATING PROCEDURE
33. cosets pP INE I ONSERNNEIE enesis EROR NESSUN UE EYIMI S Ud Mua Is Se eo NER QU PPAR 15 8 1 OSD On Screen Display PORM MAT eere tee ded zany Fono FoU das obe Y NUES Duet Le ode ages 15 9 2 MENU DESCRIPTION Siilin oup vdd td Tad ebat tei te en cer id Muf 18 8 3 SUB MENU DESCRIPTIONS crinii ise ever Lec EXER AVE RYE ANY YARN SES LAETUS YS ai 19 9 Camera Control Command Protocol ssc sccccosasssssssssneccscswsessesecvsasvesveassansensvonesessoassensseovesnentooss 26 JN EG mbil TREAS 26 D2 TG Command EF Er P RUE 27 9 3 aevi E 58 IO SPECIEICATIONS T niea HN RH ERRORES OE BRNNIARROINU MEEA ER EE USE 60 The author assumes no responsibility for any errors or omissions that may appear in this document nor does the author make a commitment to update the information herein VER 1 0 P N R040158 1 SAFETY PRECAUTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRICAL SHOCK DO NOT OPEN COVERS OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL It is advised to read the Safety Precaution Guide through carefully before operating the product to prevent any possible danger WARNING This symbol is intended to alert the user to the presence of un insulated dangerous voltage CAUTION This symbol is intended to alert the user to presence of important operating and maintenance Servicing instructions in the literature acc
34. e must be AUTO IRIS MAN or AGC MAN Use for RS 232C Serial Communication Scroll down the Brightness level KN RS BRTdn 0x47 The AE mode must be AUTO IRIS MAN or AGC MAN Use for RS 232C Serial Communication Scroll up the HUE level in Hue KN_RS_HUEup 0x4C White Balance mode Use for RS 232C Serial Communication Scroll down the HUE level in KN_RS_HUEdn 0x4D Hue White Balance mode Use for RS 232C Serial Communication Switch the Push White Balance KN_RS_WB_PUSH Ox4E ON or OFF in Push White Balance mode Use for RS 232C Serial Communication In case of displaying the MENU KN RS MITEM UP Ox4F Scroll up the MENU item Use for RS 232C Serial Communication In case of displaying the MENU KN RS MITEM DN 0x50 Scroll down the MENU item Use for RS 232C Serial Communication Switch the Focus mode KN RS AMkey SET 0x51 AUTO MANUAL or Push AUTO Use for RS 232C Serial Communication Reset the Camera mode to KN_RS_INIT_SET 0x52 default value KN RS SRPup 0x53 Use for RS 232C Serial Communication Scroll up the Sharpness level KN_RS_SRPdn 0x54 Use for RS 232C Serial Communication Scroll up the Sharpness level KN_Day_Mode_Control 0x93 Set the Day amp Night DAY Mode KN_Night_Mode_Control 0x94 Set the Day amp Night NIGHT Mode Toggle Day amp Night Control Mode of camera KN_DayNight_Mode_Control 0x95 AE Mode SENSOR Mode Day Mode Night Mode External Mode
35. ease key panel 8 3 SUB MENU DESCRIPTIONS FOCUS SET FOCUS MODE SET This function is for focus mode setting Setthe mode to Auto Manual or Push Auto FOCUS DISTANCE SET This function is for selection of minimum shooting distance Setthe Focus Distance mode to 1cm 10cm 50cm 1M 1 5M 3M 5M or 10M ZOOM START SET This function is for selection of zoom start position Setthe Zoom Start mode from x1 to x34 ZOOM END SET This function is for selection of zoom end position Setthe Zoom End mode from x560 to x2 ZOOM SPEED SET This function is for selection of zoom speed Setthe Zoom Speed to slow normal or high ZOOM TRACKING MODE SET This function is for selection of zoom tracking mode Setthe Zoom Tracking mode to Auto or Manual Zoom Tracking means focused zooming state INITIAL SET If initial mode set to ON All FOCUS function is changed to the factory setting RETURN TO MAIN MENU Exit the FOCUS set of OSD menu and return to the main menu 19 AWB SET WB MODE SET This function is for changing the WB mode Setthe mode to Auto Hue Indoor Outdoor Manual or Push Auto AUTO WB color temperature range 2500 K 8000 K Manual WB Adjust Red and Blue gain to perform a desired White Balance PUSH AUTO Set the WB mode to Push Auto HUE CONTROL SET This function is valid for Hue WB mode
36. ecomes ON mode 2 Incase of MODE 0x00 the 100 NEGATIVE mode becomes OFF mode 3 Otherwise the 10076 NEGATIVE mode remains unchanged FOCUS Mode Setting Switch the FOCUS mode to AUTO MANUAL or PUSH AUTO according to the data of MODE PC Camera 0xC5 OxAA 0x73 MODE CAM ID C S Camera PC 0xC5 OxAA 0x73 MODE 0x73 OxXX OxXX OxXX C S In case of MODE 0x00 the FOCUS mode becomes AUTO mode In case of MODE 0x01 the FOCUS mode becomes MANUAL mode In case of MODE 0x02 the FOCUS mode becomes PUSH AUTO mode Otherwise the FOCUS mode remains unchanged Br a LES 35 FLICKERLESS Mode ON OFF Setting Switch the FLICKERLESS mode to ON or OFF according to the data of the MODE PC Camera 0xC5 OxAA 0x74 MODE CAM ID C S Camera PC OxC5 Ox AA 0x74 MODE 0x74 OxXX OxXX OxXX C S 1 Incase of MODE 0x01 the FLICKERLESS mode becomes ON mode 2 In case of MODE 0x00 the FLICKERLESS mode becomes OFF mode 3 Otherwise the FLICKERLESS mode remains unchanged Hue White Balance Mode MWB CTL data Setting Set the MWB CTL data at Hue White Balance mode according to the data of MWB_CTL PC Camera 0xC5 OxAA 0x77 MWB_CTL CAM IDC S Camera PC OxC5 OxAA 0x77 MWB CTL 0x77 OxXX OxXX OxXX C S MWB CTL This is a data for which adjusts a HUE point at the Hue White Balance mode Data range 00 99 White Balance PUSH AUTO ON OFF Setting Switch the PUSH A
37. era is realized the protocol comes from PC b Byte 2 Byte 1 data is received from PC c Byte 3 Byte 2 data is received from PC d Byte 4 Byte 3 data is received from PC e Byte 5 The data is changeable according to the PC Command f Byte 6 The data is changeable according to the PC Command g Byte 7 The data is changeable according to the PC Command h Byte 8 The data is changeable according to the PC Command i Byte 9 The value of Check Sum from Byte 1 to Byte 8 The computing method is the same as Byte6 of the communication from PC to Camera 9 2 PC Command Exposure Mode Setting Set the mode of Exposure according to AEmodeCNT PC Camera 0xC5 OxAA 0x60 AEmodeCNT CAM ID C S Camera PC OxC5 OxAA 0x60 AEmodeCNT 0x60 OxXX OxXX OxXX C S AEmodeCNT The counter for setting Exposure Mode l 2 3 In case of AEmodeCNT 0x00 the Exposure Mode becomes AUTO mode In case of AEmodeCNT 0x01 this value is not used In case of AEmodeCNT 0x02 the Exposure Mode becomes IRIS MAN mode And then you can adjust IRIS level manually In case of AEmodeCNT 0x03 the Exposure Mode becomes AGC MAN mode And you can adjust AGC level manually In case of AEmodeCNT 0x04 the Exposure Mode becomes MANUAL mode And you can adjust IRIS level and AGC level manually In case of AEmodeCNT every other value the Exposure Mode remains changed 27 BACKL
38. ge data assigned the camera PC Camera 0xC5 0x59 0x00 0x00 CAM ID C S Camera PC OxC5 0x59 0x00 0x00 Distance OxXX OxXX OxXX C S 53 Distance The index value which indicates the current object distance range that the camera can be focused 1 Incase of Distance 0x00 the Focusing range From 1 cm To infinite 2 Incase of Distance 0x01 the Focusing range From 10 cm To infinite 3 In case of Distance 0x02 the Focusing range From 50 cm To infinite 4 Incase of Distance 0x03 the Focusing range From 1 m To infinite 5 Incase of Distance 0x04 the Focusing range From 3 m To infinite 6 Incase of Distance 0x05 the Focusing range From 5 m To infinite 7 Incase of Distance 0x06 the Focusing range From 10 m To infinite User Title Display ON Command This command displays the user title on the screen PC Camera 0xC5 0x67 0x00 0x00 CAM ID C S Camera PC OxC5 0x67 0x00 0x00 0x00 OxXX OxXX OxXX C S User Title Display OFF Command This command does not display the user title on the screen PC Camera 0xC5 0x68 0x00 0x00 CAM ID C S Camera PC OxC5 0x68 0x00 0x00 0x00 OxXX OxXX OxXX C S User Title String Editing Command This command edits the user title string PC Camera 0xC5 0x66 INDEX CHAR CAM ID C S Camera PC 0xC5 0x66 INDEX CHAR INDEX OxXX OxXX OxXX C S 1 INDEX The index value which indicates the character position of the u
39. ght mode becomes SUPER mode Qv sr eur In case of MODE every other value the back light mode remains unchanged Back Light Control Mode Read Command This command reads the current back light mode of the camera PC Camera 0xC5 OxAA 0x9D 0x00 CAM ID C S Camera PC OxC5 OxAA 0x9D 0x00 MODE OxXX OxXX OxXX C S 1 Incase of MODE 0x00 the current back light mode is OFF mode 2 Incase of MODE 0x01 the current back light mode is ON mode 3 In case of MODE 0x02 the current back light mode is AUTO mode 4 Incase of MODE 0x03 the current back light mode is SUPER mode 51 Wide Burst Function On Off Control Command This command controls the wide burst function of the camera according to ONOFF PC Camera 0xC5 OxAA Ox9E ONOFF CAM ID C S Camera PC OxC5 OxAA Ox9E ONOFF Ox9E OxXX OxXX OxXX C S 1 In case of ONOFF 0x00 the wide burst function becomes OFF mode 2 Incase of ONOFF 0x01 the wide burst function becomes ON mode 3 In case of ONOFF every other value the wide burst function mode remains unchanged Red Control Gain Adjust Command This command adjusts the red control gain of the camera PC Camera O0xC5 OxAA 0xA4 R_Cont CAM ID C S Camera PC OxC5 OxAA 0xA4 R Cont 0xA4 OxXX OxXX OxXX C S R Cont The value which adjusts the red control gain of the camera Red Control Gain Read Command This command reads the current red gain of the camera PC Camera 0xC5
40. he main MENU KN_POWER 0x32 Switch the power of the Camera ON OFF In the manual focus mode move the Focus lens to FAR side slowly In KN_R_FAR 0x38 case of displaying the MENU it operates as the Decrease the data of selected item in MENU 58 In the manual focus mode move the Focus lens to NEAR side slowly In KN R NEAR 0x39 case of displaying the MENU it operates as the Increase the data of selected item in MENU According to Key selection mode operate the key such as AUTO KN_AM_P Ox3F MANUAL Toggle or Push AUTO KN_RS_SSCup 0x40 Use for RS 232C Serial Communication Scroll up the Shutter Speed KN_RS_SSCdn 0x41 Use for RS 232C Serial Communication Scroll down the Shutter Speed Use for RS 232C Serial Communication Scroll up the Iris level of lens KN RS IRISup 0x42 The AE mode must be IRIS MAN or MANUAL Use for RS 232C Serial Communication Scroll down the Iris level of lens KN RS IRISdn 0x43 The AE mode must be IRIS MAN or MANUAL Use for RS 232C Serial Communication Scroll up the AGC level The AE KN RS AGCup 0x44 mode must be AGC MAN or MANUAL Use for RS 232C Serial Communication Scroll down the AGC level The KN_RS_AGCdn 0x45 AE mode must be AGC MAN or MANUAL Use for RS 232C Serial Communication Scroll up the Brightness level KN RS BRTup 0x46 The AE mod
41. matically or manually for day and night 24 hour surveillance Perfect use for Bank Treasury ATM Road Station Port Square Warehouse and etc The chassis is equipped with IR cut filter change mechanism When Day amp Night mode is set to AE on the OSD menu of the camera the camera will turn the IR Cut Filter according to exposure of the object When the Day amp Night mode is set to Sensor on the OSD menu of the camera the camera will turn the IR Cut Filter according to the sensitivity of the SENSOR Setup Menu Function via Keys Pushing keys on the rear panel of the camera can set each setup menu function Setup menu functions are displayed on screen display OSD Camera Control via either RS 422 RS 485 or RS 232 optional interface Camera control can adjust the camera s zoom focus Iris and white balance via either RS 422 RS 485 or RS 232 optional interface e Built in Wire Remote Control Interface including Wet Contact and A D Key Wet contact interface is to control zooming and focusing There are Menu Tele Wide Near Far and On Off signals via A D key control The A D Key control signal can be sent from Wire Remote Controller optional Built in Pan Tilt Zoom PTZ Protocols The camera automatically recognizes four protocols such as native protocol PELCO D and P protocol and LG protocol Camera parameters can easily be setup via native keyboard RS 485 or PELCO keyboard RS 422 3 FEATURES e 1 4
42. n OSD is or not displayed 1 Incase of ONOFF 0x00 the selected function OSD is not displayed on the screen 2 Incase of ONOFF 0x01 the selected function OSD is displayed on the screen 3 In case of every other value the display status of the selected function OSD remains unchanged Index Explanation 0x00 Select the general function OSD 0x01 Reserved 0x02 Select the function OSD that is related to the Camera ID 0x03 Select the function OSD that is related to the Zoom Magnitude 0x04 Select the function OSD that is related to the User Title 0x05 Select the function OSD that is related to the Power On Initial Title Dark Fade ON Video Mute Command This command mutes the video signal out PC Camera 0xC5 OxAA 0x54 0x00 CAM ID C S Camera PC OxC5 OxAA 0x54 0x00 0x54 OxXX OxXX OxXX C S Dark Fade OFF Video Mute Release Command This command releases the video signal which is muted PC Camera 0xC5 OxAA 0x55 0x00 CAM ID C S Camera PC OxC5 OxAA 0x55 0x00 0x55 OxXX OxXX OxXX C S Set Day amp Night Control Mode This command is to set the camera s Day amp Night control mode PC Camera 0xC5 0x77 Day amp Night Mode 0x00 CAM ID C S Camera PC 0xC5 0x77 Day amp Night Mode 0x00 Day amp Night Mode 0xXX OxXX 0xXX C S 56 Day amp Night Mode Explanation 0x00 Camera s Day amp Night Control Mode becomes Night Mode 0x01 Camera s Da
43. n case of KN HWIDE 0x04 displaying the MENU it operates as the MENU selection scroll down In the manual focus mode move the Focus lens to FAR side KN FAR 0x08 quickly In case of displaying the MENU it operates as the Decrease the data of a selected item on the MENU In the manual focus mode move the Focus lens to NEAR side quickly KN NEAR 0x09 Incase of displaying the MENU it operates as the Increase the data of a selected item on the MENU In the manual focus mode move the Focus lens to FAR side by 1 step In KN SFAR Ox0A case of displaying the MENU it operates as the Decrease the data of a selected item on the MENU In the manual focus mode move the Focus lens to NEAR side by 1 step KN SNEAR OxOB Incase of displaying the MENU it operates as the Increase the data of a selected item on the MENU KN STOP EO Stop all key actions that are being performed currently After using the key action the camera has to be notified by the stop of key action KN BL Ox1A Switch the BACKLIGHT mode ON OFF KN FLICKER Ox1B Switch the FLICKERLESS mode ON OFF KN NEGA Ox1E Switch the NEGATIVE mode Negative Positive KN DZOOM 0x22 Switch the Digital Zoom mode ON OFF KN OSD 0x24 Switch the Key function OSD ON OFF KN MENU 0x25 Switch the main MENU ON OFF KN M UP Ox27 Increase the data of a selected item on the main MENU KN M DN 0x28 Decrease the data of a selected item on t
44. ompanying the appliance X Disposal of Old Electrical amp Electronic Equipment Applicable in the European Union and other European countries with separate collection systems EE This symbol on the product or on its packaging indicates that this product shall not be treated as household waste By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product The recycling of materials will help to conserve natural resources For more detailed information about recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product Do not touch the zoom lens directly with your hands or fingers Clean the zoom lens using soft cloth moistened with alcohol to wipe off any dust Please be extra careful not to shake the product and avoid places where frequent vibrations or shocks may occur Do not install the product in extreme temperature conditions Only use the camera under conditions where temperatures are between 10 and 50 Do not install the product in an environment where the humidity is high Do not spill liquid of any kind on the product If it gets wet wipe it dry immediately Alcohol or beverage can contain minerals that corrode the electronic components When minimum brightness of 0 01 Lux cannot
45. r PUSH_AUTO And is not performed during Zooming PC Camera 0xC5 OxAA 0x5D STEP CAM ID C S Camera PC OxC5 OxAA 0x5D STEP Ox5D OxXX OxXX OxXX C S STEP The value specifying the number step to move the focus lens in the direction of FAR Focus Lens NEAR Direction Step Move Command This Command moves the focus lens by a specific number step in the direction of NEAR 48 Caution This command is performed when the focus mode is MANUAL or PUSH AUTO And is not performed during Zooming PC Camera 0xC5 OxAA Ox5E STEP CAM ID C S Camera PC OxC5 OxAA Ox5E STEP Ox5E OxXX OxXX OxXX C S STEP The value specifying the step number to move the focus lens in the direction of NEAR MENU OSD Display On Off Command This Command decides whether or not the MENU OSD is to be displayed on the screen according to INDEX PC Camera 0xC5 OxAA 0x6F INDEX CAM ID C S Camera PC OxC5 OxAA Ox6F INDEX Ox6F OxXX OxXX OxXX C S INDEX The value which selects the MENU OSD page or erases the MENU OSD on the screen In case of INDEX 0x00 the Main Menu OSD is displayed In case of INDEX 0x01 the Focus Sub Menu OSD is displayed In case of INDEX 0x02 the White Balance Sub Menu OSD is displayed In case of INDEX 0x03 the Exposure Sub Menu OSD is displayed In case of INDEX 0x04 the Special Function Sub Menu OSD is displayed In case of INDEX 0x06 the Function O
46. ra PC 44 0xC5 OxAA 0x8A 0x00 SSC_CNT OxXX OxXX OxXX C S Read the IRIS control data Read the current IRIS control value to control IRIS OPEN level The data is IRIS_CTL PC Camera 0xC5 OxAA 0x8B 0x00 CAM ID C S Camera PC OxC5 OxAA Ox8B 0x00 IRIS CTL OxXX OxXX OxXX C S Read the AGC control data Read the current AGC control value to control AGC level The data is AGC_CTL PC Camera OxC5 OxAA 0x8C 0x00 CAM ID C S Camera PC OxC5 OxAA 0x8C 0x00 AGC_CTL OxXX OxXX OxXX C S Read the MENU OSD ON OFF status Read the current MENU OSD ON OFF state of the camera The data is M STATE PC Camera OxC5 OxAA Ox8D 0x00 CAM ID C S Camera PC OxC5 OxAA 0x8D 0x00 M STATE OxXX OxXX OxXX C S 1 Incase of M STATE 0x00 the MENU OSD is currently not displayed 2 Incase of M STATE 0x01 the MENU OSD is currently displayed Read the Function OSD Display Mode Read the current Function OSD Display mode of the camera The data is OSD DISP PC Camera 0xC5 OxAA Ox8E 0x00 CAM ID C S Camera PC OxC5 OxAA Ox8E 0x00 OSD DISP OxXX OxXX OxXX C S 45 Read the Digital Zoom Max Power Mode Read the current Max Power Digital Zoom Mode of the camera The data is DZ MAX PC Camera 0xC5 OxAA Ox8F 0x00 CAM ID C S Camera PC OxC5 OxAA Ox8F 0x00 DZ MAX OxXX OxXX OxXX C S Caution The data of this command is valid only when the Digital Zoom mode is ON
47. real area2 area3 or area4 The back light compensation is enabled automatically When the back light condition disappears in that area BLC is disabled automatically To disable this mode set it to OFF BLC area is Area 0 SUPER BLC BLC could emphasize the luminance of the image according to the light condition 21 BLC LEVEL SET This function is valid for BLC ON mode Adjust the level from 0 MIN to 80 MAX BLC AREA SET This function is valid for BLC ON or AUTO BLC mode Define the main object area that is under exposure based on the average luminance of the whole image Set the BLC area Center area 0 Top Small TopS areal area2 Top Large TopL areal area2 area0 Bottom Small BottomS area3 area4 Bottom Large BottomL area3 area4 area0 Left areal area3 or Right area2 area4 FLICKERLESS SET Select the mode ON or OFF Use for preventing picture flicker Incase of NTSC System Shutter Speed is 1 100 sec Incase of PAL System Shutter Speed is 1 120 sec SHUTTER SPEED SET Set the mode Normal NTSC 1 60 PAL 1 50 1 125 1 150 1 200 1 250 1 300 1 350 1 400 1 450 1 500 1 600 1 700 1 800 1 900 1 1000 1 1100 1 1200 1 1300 1 1500 1 1600 1 1800 1 2000 1 2500 1 3000 1 3500 1 4000 1 6000 1 10000 1 30000 sec INITIAL SET If initial mode set to ON All AE function is changed to the factory setting RETURN TO MAIN MENU
48. refer to figure 5 4 Name Function RD TD GND Use for RS 232 Control 7 Day amp Night Control refer to figure 5 3 or 5 4 Name Function 5V 10mA IR LED ON NIGHT DAY amp NIGHT OUTPUT DNO 0V IR LED OFF DAY Open Contact DAY DAY amp NIGHT EXTERNAL INPUT DNI Close Contact Close to GND NIGHT Day amp Night Output This function will turn on the external IR LED lamp according to the position of IR cut filter e Day amp Night Output 5V 10mA IR LED ON NIGHT OV IR LED OFF DAY e Day amp Night External Input When Day amp Night mode is set to External on the OSD menu of the camera this function will be switched to DAY mode or NIGHT mode according to the Day amp Night signal from the external light sensor or the IR LED lamp Open Contact DAY Close Contact Close to GND NIGHT 6 INSTALLATION RS 232 D Sub Connector 1 Frame GND 2 RD 3 TD 4 DTR 5 Signal GND 6 DSR 7 RTS 8 CTS 9 RI Camera RS 232 Interface Figure 6 1 Camera RS 422 Interface RS 232 to RS 422 Converter D To PC or Controller Figure 6 2 Camera RS 485 Interface RS 232 to RS 485 Converter To PC or Controller Figure 6 3 6 1 Native Keyboard Installation 1 RS 485 interface is used for communicating native keyboard Refer to Figure 6 3 connect R and T of the camera together connect R and T of the camera to D of the n
49. ser title string in order to edit The range of this value is from 0x00 to 0x09 2 CHAR The code value in order to edit the character pointed by INDEX 54 CHAR Character CHAR Character CHAR Character 0x00 A Ox1A a 0x34 0 0x01 B Ox1B b 0x35 T 0x02 C Ox1C c 0x36 27 0x03 D Ox1D q 0x37 F 0x04 F Ox1E te 0x38 ut 0x05 d Ox1F P 0x39 P 0x06 G 0x20 g Ox3A 0x07 H 0x21 h 0x3B D 0x08 T 0x22 T 0x3C g 0x09 J 0x23 Jg Ox3D 9 Ox0A K 0x24 K Ox3E 2 OxOB T 0x25 P Ox3F E 0x0C M 0x26 m 0x40 s OxOD N 0x27 n 0x41 uer OxOE 0x28 o 0x42 and OxOF P 0x29 p 0x43 0x10 Q 0x2A q 0x44 x Ox11 R 0x2B rr 0x45 ur 0x12 S 0x2C g 0x46 T 0x13 T 0x2D a 0x47 Db 0x14 U Ox2E tu 0x48 E 0x15 NT Ox2F vt 0x49 gt 0x16 W 0x30 w 0x4A V 0x17 UC 0x31 x 0x4B te 0x18 Y 0x32 ty Ox4C et 0x19 VA 0x33 z 0x4D Blank Function OSD Display On Off Setting Command This command indicates whether each function OSD of the camera is displayed on the screen PC gt Camera 0xC5 0x6B INDEX ONOFF CAM ID C S Camera PC OxC5 0x6B INDEX ONOFF INDEX OxXX OxXX OxXX C S 55 INDEX The index value to select whether or not to display the function OSD ONOFF The value which indicates whether the selected functio
50. tor Zoom Focus A D Key DC12V IN Key Control Tele Up Wide Down Near Far Menu Day Night Control Day Night Output Day Night External Input Operating Temperature 10 C to 50 C Operating Humidity 0 RH 60 RH Supplied Voltage DC 12 V 10 Recommendation DC 12V 0 5 V Power Consumption Max 4 1W Dimensions 60 x 50 x 130mm WxHxD Letters in BOLD Default Mode Note Design and specifications are subject to change without prior notice 60 ACCESSORIES IR Remote Keyboard Controller Model XSDIDCIR The Xvision XSDIDCIR is an IR Remote Control and transmitter set The transmitter simply connects to the Zoom camera and then the IR Remote Control can be used to control the Zoom Focus and Menu of the camera Wall Ceiling camera mounting bracket Model WH160 The Xvision WH160 bracket allows you to fix industry standard CCTV cameras to a wall or ceiling Weatherproof housing and wall bracket Model HCW200 The Xvision HCW200 weatherproof housing and bracket allows external wall mounting of industry standard CCTV cameras in temperatures from 10 to 40 C Weatherproof housing and ceiling bracket Model HCW200CB The Xvision HCW200CB weatherproof housing and bracket allows external ceiling mounting of industry standard CCTV cameras in temperatures from 10 to 40 C Professional weatherproof housing and wall bracket with built in Heater and Fan Cable Managed Model
51. tup Menu Mode PELCO Keyboard Camera Function OPEN Sub Menu Enter CLOSE Sub Menu Exit NEAR Cursor Up FAR Cursor Down Twist Joystick clockwise or Zoom In None Twist Joystick counterclockwise or Zoom Out None Move Joystick Left Decrease Move Joystick Right Increase Move Joystick Up Cursor Up Move Joystick Down Cursor Down Please refer to PELCO Keyboard or compatible manual for more information 14 8 SYSTEM SETUP 8 1 OSD On Screen Display FORMAT OSD DISPLAY POSITION Figure 8 1 OSD DISPLAY DESCRIPTION FUNCTION OSD Format DESCRIPTION Non display Auto Mode 1 FOCUS MODE i Manual Push Auto Mode Non display Back Light OFF 2 BACK LIGHT BLC display BLCON Auto Super BLC Mode Normal Shutter Non display NTSC 1 60 PAL 1 50 Ff display Flickerless Mode 3 SHUTTER SPEED 1 125 29 variable steps 1 30 000 AWB AUTO White Balance HUE The HUE control is valid 0 99 IWB WB Preset for INDOOR OWB WB Preset for OUTDOOR 4 WBC MODE MWB Manual WB Adjustment Push Auto White Balance turn this PWB mode ON the white trace automatically Turn this mode OFF Preserve the white of final auto tracing action Manual AUTO NATIVE After power on information on PROTOCOL PELCO LG PROTOCOL and COMM will be 5 1 displayed Setting string This information will remain on the
52. ure Mode is IRIS MAN or MANUAL 38 AGC Level Setting Set the AGC Level of the camera according to the data of AGC_CTL PC Camera 0xC5 OxAA 0x7D AGC CTL CAM ID C S Camera PC OxC5 OxAA Ox7D AGC_CTL Ox7D OxXX OxXX OxXX C S AGC_CTL The data for adjusting the AGC level of the camera Data value range from Ox1C Minimum AGC Level to OXDC Maximum AGC Level Caution This command is valid when the Exposure Mode is AGC MAN or MANUAL Function OSD Display Mode Change Change the Function OSD Display Mode of the camera according to the data of OSD DISP PC Camera OxC5 OxAA 0x64 OSD DISP CAM ID C S Camera PC OxC5 OxAA 0x64 OSD DISP 0x64 OxXX OxXX OxXX C S OSD DISP Bit Explanation 7 Reserved Fix to 0 6 Reserved Fix to 0 0 OFF 5 1 General Function OSD Display ON Focus Auto Manual OSD Back Light OSD Shutter Speed OSD White Balance Mode OSD 4 Reserved Fix to 0 3 0 OFF Camera ID OSD Display ON OFF Zoom Magnitude OSD Display ON OFF User Title OSD Display ON OFF Power ON Initial Title OSD Display ON 2 Oj Oj Oj 39 Digital Zoom Mode ON OFF Setting Switch the Digital Zoom mode to ON or OFF according to the data of MODE PC Camera 0xC5 OxAA 0x6E MODE CAM ID C S Camera PC OxC5 OxAA Ox6E MODE Ox6E OxXX OxXX OxXX C S 1 In case of MODE 0x01 the
53. us of the camera The data is CAM CON2 PC Camera O0xC5 OxAA 0x81 0x00 CAM ID C S Camera PC OxCS Ox AA 0x81 0x00 CAM CON2 OxXX OxXX OxXX C S Construction of CAM CON2 data Bit Explanation 1 Indicating that the camera recheck the object distance for Zoom Tracking Reserved Reserved Reserved Reserved Reserved INIWASAN Reserved 0 Auto BACKLIGHT Mode OFF state 1 Auto BACKLIGHT Mode ON state Digital Effect status of the Camera Read Command Read the current Digital Effect status of the camera The data is DEFT_CON PC Camera OxC5 OxAA 0x82 0x00 CAM ID C S Camera PC OxC5 OxAA 0x82 0x00 DEFT CON OxXX OxXX OxXX C S Construction of DEFT CON data 42 Bit Explanation 7 Reserved 0 Mosaic OFF state 1 Mosaic ON state 0 Color ON state 1 Color OFF state 4 Reserved 0 10096 Negative OFF state 3 1 100 Negative ON state 2 0 Screen Inversion OFF state 1 Screen Inversion ON state 1 Reserved 0 Reserved Read the White Balance Mode Read the current White Balance Mode of the camera The data is WB MODE PC Camera 0xC5 OxAA 0x83 0x00 CAM ID C S Camera PC OxC5 OxAA 0x83 0x00 WB MODE OxXX OxXX OxXX C S Explanation of WB_MODE data WB MODE Explanation 0x0 AUTO White Balance mode Ox1 HUE White Balance mode 0x2 I
54. xAA 0x6A 0x00 CAM ID C S Camera PC OxC5 Ox AA 0x6A 0x00 0x6A OxXX OxXX OxXX CS Caution If the Camera ID is OFF mode then the Camera ID is not displayed Zoom Lens Position Read Read the current position value of Zoom lens amp Digital Zoom MAG data PC Camera 0xC5 0x36 0x00 0x00 CAM ID C S Camera PC 0xC5 0x36 0x00 0x00 ZP_CNT 1 ZP CNT V MAG 0xXX C S 1 ZP_CNT 1 Upper byte of Zoom lens position 2 ZP CNT Lower byte of Zoom lens position 3 V MAG Digital zoom data Ex In case of Zoom lens Position 0x12A amp Digital zoom data 0x10 a ZP_CNT 1 0x01 b ZP CNT 0x2A c V MAG 0x10 Caution This command is used to set the PRESET mode control Focus Lens Position Read Read the current value of Focus lens PC Camera OxC5 0x37 0x00 0x00 CAM ID C S 29 Camera PC OxC5 0x37 0x00 0x00 FP CNT 1 FP CNT OxXX OxXX C S 1 FP CNT I Upper byte of Focus lens position 2 FP CNT Lower byte of Focus lens position Ex In case of Focus lens Position 0x1A2 a FP_CNT 1 0x01 b FP_CNT 0xA2 Caution This command is used to set the PRESET mode Camera Power ON Turn on the power of Camera PC Camera O0xC5 0x3A 0x00 0x00 CAM ID C S Camera PC OxC5 0x3A 0x00 0x00 0x00 0x00 OxXX OxXX C S Camera Power OFF Turn off the power of Camera PC Camera 0xC5 Ox3E 0x00 0x00 CAM ID C S Camera PC OxC5 Ox3E 0x00 0x00 0x00 0x00 OxXX OxXX C S Memorize
55. y amp Night Control Mode becomes Day Mode 0x02 Camera s Day amp Night Control Mode becomes AE Mode Camera toggle Day or Night Mode according to exposure of object Camera s Day amp Night Control Mode becomes SENSOR Mode 0x03 Camera toggle Day or Night Mode according to sensitivity of SENSOR 0x04 Camera s Day amp Night Control Mode becomes External Mode Other Values No Operation Read Day amp Night Control Mode This command is to see the camera s Day amp Night control mode PC Camera OxCS OxAA 0x81 0x00 CAM ID C S Camera PC OxC5 OxAA 0x81 0x00 Status OxXX OxXX OxXX C S The status of Camera operation Bit5 amp Bit4 are the flags of Day amp Night Control Mode Status Bit5 Bit4 Explanation 0 0 Camera s Day amp Night Control Mode is Day amp Night DAY Mode 0 1 Camera s Day amp Night Control Mode is Day amp Night NIGHT Mode Camera s Day amp Night Control Mode is Day amp Night AUTO Mode and the status of Camera s Day amp i g Night Control is Day Mode Camera s Day amp Night Control Mode is Day amp Night AUTO Mode and the status of Camera s Day amp i Night Control is Night Mode Set Day amp Night Data This command is to set the camera s Day amp Night data PC Camera OxC5 OxOF Day amp Night Index Data CAM ID C S Camera PC 0xC5 OxOF Day amp Night Index Data Day

User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents