www.uobd2.com
Contents
1. the electrical circuit of AdBlue system and after the identification of the fuse controlling the power feeding of the AdBlue sysiem the vehicle power batteries can be reconnected The SEAS module acquires inputs from the CAN Bus line the first time the dashboard Is turned on key ON but engine still OFF Please make sure that fuse is correctly inserted and placed then follow the procedure e Turn on the dashboard key ON and verify that the YELLOW LED is turned on too e After approx 1 minute the YELLOW LED switches off and a GREEN LED will turn on e Switch off the dashboard key OFF After this procedure the SEAS module will be activated whenever the dashboard will be turned on key ON The result will be e If the fuse F109 is installed the AdBlue system will be working and the two LED will always be on e lf the fuse F109 is not installed the AdBlue system will not be working and the SEAS module will be activated the two LED will be flashing All the operations on the fuse have to be performed ONLY with the dashboard switched off key OFF SEAS module diagnostic table of LED Light Emission Diode DASHBOARD YELLOW LED GREENLED State of the SEAS module KEY OFF No power feeding Not programmed ON OFF Programmed waiting for self learning KEY ON OFF ON Auto acquiring operations completed ___ ON ON Datasaved modulenotactivated _ Renault_eng doc Pagina 5 di 5 Ver 0 12. Blue ECU EARTH 1 a Renault_eng doc Pagina 4 di 5 Ver 0 1 w OBD2 China TERE Notes on the Activation signal The SEAS module and the original AdBlue system cannot be both activated at the same time the grey Activation wire 30 is utilized to enable automatically the SEAS module working For this reason it is extremely important to connect this wire to a 24 Volt source always available battery moreover the soldering operation must be done between the 25 Amp Fuse F109 and the AdBlue module Consequently if you want to stop and exclude the original AdBlue system working it is enough to remove the fuse before starting the engine The SEAS module will automatically be activated To reset the original AdBlue system working it is enough to re install the fuse F109 before starting the engine The SEAS module will be de activated IMPORTANT the fuse is located into the battery niche close to 2 other fuses one 5 Ampere and one 25 Ampere fuse Follow the procedure to identify the correct fuse the vehicle power batteries must be kept disconnected Remove the two 25 Ampere fuses from their fuse site By using a multimeter you have to find the electric continuity between PIN 3 or 4 on the AdBlue connector and the fuse sites Identify the fuse site of AdBlue system mark it and reconnect the two 25 ampere fuses Self learning CAN Bus line Once the SEAS module is fully connected to
3. W OBD2 RETE China Auto Diagnostic Tool Center SEAS INSTRUCTIONS RENAULT Please read the complete document before starting the installation Brand assignment SEAS add on module is delivered NOT PROGRAMMED therefore a brand Renault in this case must be set with computer and specific program SETUP TRUCK This procedure can be achieved both before and after the installation on the vehicle if after the installation the vehicle power batteries must be disconnected during the operations Connect the programming cable to the USB port of your PC Connect the programming cable to the SEAS module by using the white 4 pins connector during this operation the LED Light Emission Diode of the SEAS module will be off Run the program SimulaCan select it from the list of programs installed on your pc Proceed as follow ea sere TRUK TTF Start tri Select Start seni Ra Quit a SETUP TRUK ef x Wait for next screen displayed the time required can vary according to the quantity of virtual COM installed Renault_eng doc Pagina 1 di 5 Ver 0 1 W OBD2 RETE China Auto Diagnoste Tool Center 2 SETUP TRUK By x If the connection is successfully achieved serial communication recognized and accepted the program will display this page you can now select RENAULT brand Select Send PROG When the programming operation is completed the yellow LED on your SEAS module will t
4. he engine key is in ON position dashboard ON BLACK earth to be connected to an earth available preferably the same as AdBlue GREY 30 to be connected to a 24 Volt source always available of AdBlue system necessarily BETWEEN the F109 protection fuse and the AdBlue system e CAN Bus line connection The two conductors plaited together must be connected to the CAN Bus line of the AdBlue system WHITE CAN H to be connected to CAN H of the system that must be simulated BROWN CAN L to be connected to CAN L of the system that must be simulated The connections must be done inside the original AdBlue connector the AdBlue ECU is located on the chassis The SEAS module is waterproof so it can be placed onto any support even the vehicle chassis Should the wiring provided with the SEAS module be too long it can be shortened In contrast the same wiring cannot be extended The 5 conductors of SEAS module must be soldered to the 5 conductors of the AdBlue system SEAS Module Renault AdBlue system CAN L CAN L 6 Purple 0463 CAN H CAN H Brown 0462 Son 24 Volt always available 30 between sora 2328 Activation 30 F109 fuse 25 Amp and AdBlue 30r4 2328 24 Volt under key 15 Red 24 Volt under key 15 2329 is Renault_eng doc Pagina 3 di 5 Ver 0 1 15 30 LU Z r amp D O pa A m Fuse F109 da 25 Amp PIN to connect the original Ad
5. urn on Select Quit to close the program SimulaCan e Disconnect the programming cable of your SEAS module and place the specific cover on top of the white 4 pins connector IMPORTANT the following instructions indicate how to connect and install your SEAS module on the original AdBlue system of the truck The number displayed and the colour of the conductors of the AdBlue system are referred to Renault Premium 450 year 2008 these details may vary according to different production lots or vehicle equipment Please refer to the schemes layouts supplied with the Renault technical manual to identify the CAN Bus line of the AdBlue system its protection fuse and the power feeding The main working procedure of SEAS modules does not vary Renault_eng doc Pagina 2 di 5 Ver 0 1 W OBD2 k kkk t China Auto Diagnoste Tool Center Installation on the vehicle Before proceedin lease make sure that the following conditions are respected e NO faulty codes memorized in the original ECU e AdBlue liquid higher than the reserve level e Vehicle batteries disconnected from the electrical circuit The SEAS module is supplied with 5 conductors e Power feeding activation RED 15 to be connected to a 24 Volt source under key 24 Volt enabled when the engine key is in ON position preferably to the same source that enables the AdBlue system working This connection will supply power to the SEAS module when t
Download Pdf Manuals
Related Search