Intimidator Spot 255 IRC Rev. 3
Contents
1. Glance Safety Notes Page 4 of 24 0 E Use on Dimmer Outdoor Use Sound Activated DMX Master Slave Auto Programs p Auto ranging Power Supply P p X Replaceable Fuse User Serviceable These notes include important information about the mounting usage and maintenance of this product read before using the product This product is not intended for permanent installation Always connect the product to a grounded circuit to avoid the risk of electrocution Always disconnect the product from power before cleaning or replacing the fuse Avoid direct eye exposure to the light source while the product is on Make sure the power cord is not crimped or damaged Never disconnect the product from power by pulling or tugging on the cord If mounting the product overhead always secure to a fastening device using a safety cable Make sure there are no flammable materials close to the product when operating Do not touch the product s housing when operating because it may be very hot Always make sure that the voltage of the outlet to which you are connecting the product is within the range stated on the decal or rear panel of the product The product is for indoor use only IP20 To prevent risk of fire or shock do not expose the product to rain or moisture Always install the product in a location with adequate ventilation at least 20 in 50 cm from adjacent surfaces Be sure that no ventilation slots on the pro2. lreland Mexico or Benelux follow their instructions on how to return Chauvet products to them Visit our Outside the U S UK Ireland Mexico or Benelux contact your distributor and E website for contact details Returns Call the corresponding Chauvet Technical Support office and request a Return Merchandise Authorization RMA number before shipping the product Be prepared to provide the model number serial number and a brief description of the cause for the return You must send the merchandise prepaid in its original box and with its original packing and accessories Chauvet will not issue call tags Clearly label the package with the RMA number Chauvet will refuse any product returned without an RMA number Write the RMA number on a properly affixed label DO NOT write the RMA number directly on the box Before sending the product clearly write the following information on a piece of paper and place it inside the box Your name Your address Your phone number RMA number A brief description of the problem Be sure to pack the product properly Any shipping damage resulting from inadequate packaging will be your responsibility FedEx packing or double boxing are recommended Chauvet reserves the right to use its own discretion to repair or replace returned product s Intimidator Spot 255 IRC User Manual Rev 3 Page 23 of 24 CONTACT US Page 24 of 24 WORLD HEADQUARTERS Chauvet General In
3. you must always consider the length of the power linking cable and mount the products close enough for the cable to reach The rubber feet also serve as floor supports When mounting the product on the floor make sure that the product and cables are away from people and vehicles Bracket Safety Cable ae such as CH 05 from Chauvet Attachment Plate l yy pe XAUS aS A Rubber Feet for Floor Mounting x4 Threaded Hole for Safety Loop behind the foot IIA AAA RRR EEE When using only one mounting clamp with this fixture you must use a clamp with a captive bolt to prevent accidental loosening Intimidator Spot 255 IRC User Manual Rev 3 4 OPERATION Control Panel To access the control panel functions use the four buttons located underneath the display Operation Button Function MENUS Press to find an operation mode or to back out of the current menu option lt UP gt Press to scroll up the list of options or to find a higher value lt DOWN gt Press to scroll down the list of options or to find a lower value lt ENTER gt Press to activate a menu option or a selected value Menu Map Main Level Programming Levels Description Address the DMX starting address en Slave Bentsen _ Selects Slave mode 1 2 3 or 4 Sound Selects Sound Active mode po Ato SelectsAutomaticmode PR Selects infrared control _ _ ___sees Fine control of panning e 0 270 Run Mode Fine Fi
4. color speed and sensitivity and set the strobe To set the product to IR mode do the following IRC 6 Operation 4 D a l a M a 0 a OOOO A Page 18 of 24 1 Pak wWD Make sure the product is plugged into a power source and not connected to a DMX cable Press lt MENU3 gt Use lt UP gt or lt DOWN gt to choose Run Mode Press lt ENTER gt Use lt UP gt or lt DOWN gt to choose IR Press lt ENTER gt and the IR indicator on the front of the Intimidator Spot 355Z IRC lights up Be sure the IRC 6 remote is pointing directly at the product and there is nothing in between the remote and the product Some of the buttons on the remote work differently than what is indicated on their labels For example lt MANUAL gt changes the Gobo pattern lt FADE gt changes the color lt R gt lt G gt lt B gt lt A gt and lt W gt control other manual functions Please read the next section carefully lt BLACKOUT gt Turns LED on and off lt AUTO gt Activates Auto mode Use the lt gt and lt gt buttons to cycle through Auto modes lt SOUND gt Activates Sound mode lt STROBE gt Activates the strobe Use the lt gt and lt gt buttons to cycle through strobe speeds lt SPEED gt Adjusts the movement speed Use the lt gt and lt gt buttons to cycle through movement speeds lt
5. range for the pan and tilt angles on the Intimidator Spot 255 Range To select which pan angle range to use do the following 1 Press lt MENU gt 2 Use lt UP gt or lt DOWN gt to choose Setup 3 Press lt ENTER gt 4 Use lt UP gt or lt DOWN gt to select Pan Angle 5 Press lt ENTER gt 6 Use lt UP gt or lt DOWN gt to select 540 360 or 180 7 Press lt ENTER gt To select which tilt angle range to use do the following 1 Press lt MENU gt 2 Use lt UP gt or lt DOWN gt to choose Setup 3 Press lt ENTER gt 4 Use lt UP gt or lt DOWN gt to select Tilt Angle 5 Press lt ENTER gt 6 Use lt UP gt or lt DOWN gt to select 270 180 or 090 7 Press lt ENTER gt Intimidator Spot 255 IRC User Manual Rev 3 Page 15 of 24 Reset Options Information gt Page 16 of 24 Display The user can flip the LED display for easy readability in any mounting situation To select the display orientation D AE o ee T E 7 Press lt MENU gt Use lt UP gt or lt DOWN gt to choose Setup Press lt ENTER gt Use lt UP gt or lt DOWN gt to select Screen Reverse Press lt ENTER gt Use lt UP gt or lt DOWN gt to select ON or OFF Press lt ENTER gt The Reset option will restart the product but does not change any settings Using the Factory Set option will clear out all customized settings and return the settings to the factory defaults To reset the software on the In
6. INTIMIDATOR Spot 255 IRC User Manual TABLE OF CONTENTS 1 Berore YOBE gI ec ese hsucce Rosas daes Get tele a 3 What IS Included 2 0 0 cccccccecececcccececccccnecececueuenecececuaunecscaucuaenerseueauaenetscauauaenerseenenenenes 3 Win packinGslins MUGHON ia es 3 Glaim See Sas heehee a Seo sre a e e e a a a e too a een ne 3 TEexLCONVENIONS eenn a ta tod toallas 3 O RO a CE ate ascoscen sine mac ucekiaateneaca eeeaennceee aa 3 Documento NAOMI Es 3 Product at a GlaNCe sta i ee ke cece cee ed ee Ee ees 4 Sale NOIE Sar eairetoe de cauiraeswtacaec deans ean ee oea peat eamamnaie 4 2 INTOdUCHION a id 5 A A esa ineree seeds 5 Product DIMENSIONS ia a da a dees deta vices ives 6 O 7 XA AREE E EEEE E EE A EATE 7 Fuse Replace MENM sseni e as E a aaa e 7 POWer MMIC cican a a a E 7 o 8 As A E EEEE E EEEE EE EEE EEEE EEA 8 RIGON dnine O E E S 8 A Operans aa ii 9 Control Panel OEM a a E 9 Ment Mapsco e a aaa 9 Contguraton DMX iross a a A 10 o A R E EES 10 DMX Peod eS x otto cs cl de ch A do is a tl a end ee les 10 5 DMX ASSIN MENTS sco ii Io aba 11 IA A A E A IA 11 DIMAS GIA COMME aeris cece ced aeoticacanasitcbieachaveernceed A EN 12 PV SA PE hah ase ate tha etl gasp EE EETA E E T EE E A AT E 13 A A seats decanaane 14 Gontiguration Sandalias ia side 14 SOUNC Active Mode 22 2cccccecceccececeecuecuececcecaececuecueceececaecuecueceeceeaecueneececaecnecueceeseeaesaecuenueaes 14 SQUAD SEMIS IVY tees a aeons 14 Autom
7. SENSITIVITY gt Adjusts sound sensitivity Use the lt gt and lt gt buttons to cycle through sound sensitivity levels lt gt Adjusts the brightness of the LEDs Use the lt gt and lt gt buttons to increase or decrease the brightness of the LEDs lt MANUAL gt Changes the Gobo pattern Use the lt gt and lt gt buttons to scroll through the GOBO options lt FADE gt Changes the color Use the lt gt and lt gt buttons to scroll through the color options lt R gt Activates color wheel rotation control Use the lt gt and lt gt buttons to increase or decrease rotation speed lt G gt Activates Gobo wheel rotation control Use the lt gt and lt gt buttons to increase or decrease rotation speed lt B gt Activates color and Gobo auto mode independent from movement lt A gt Activates pan and tilt control Press lt A gt to toggle pan and tilt and use the lt gt and lt gt buttons to increase or decrease pan or tilt values lt W gt Activates prism control Use the lt gt and lt gt buttons to set prism value 0 15 for off 16 255 for on lt gt Increases values for controls as described above lt gt Decreases values for controls as described above lt 0 gt lt 9 gt Activates specific Auto modes Can be used as a shortcut for the combination of the lt AUTO gt button and the lt gt and lt gt buttons lt UV gt or lt P gt No function with t
8. Separate the gobo holder assembly away from the gobo wheel by pushing it forward and up Be careful not to push the gobo out of the gobo plate 6 Extract the gobo holder by pulling it backwards out of the product 7 Ona flat surface remove the expansion ring that holds the gobo in place and remove the gobo from the gobo plate 8 Insert anew gobo and hold it in place with the expansion ring 9 Tore insert the new gobos slide the tip of the gobo holder under the pressure plate near the center of the gobo wheel 10 Push the gobo holder assembly inwards DO NOT force the gobo holder into the gobo wheel slot Slightly move the holder from side to side if needed to get it to seat properly If correctly installed the bottom of the holder will be flush with the gobo wheel 11 Push cover back into position Gobo Replacement Diagram Gobo Holder Removal Expansion Ring y o a 7 Ss D iiil J waa A x iii f NN o J ON SKS IN ASES Gobo Holder Assembly AZ Easy access Panel pawvanawa aami LAA DA CMA EE Gobo Wheel Detail Views Page 20 of 24 Intimidator Spot 255 IRC User Manual Rev 3 6 TECHNICAL INFORMATION Product Dust build up reduces light output performance and can cause overheating This can lead to reduction of the light source s life To maintain optimum performance and Maintenance minimize wear yo
9. ark Blue White 128U 191 Color cycle rainbow with increasing speed 192 255 Reverse color cycle rainbow with increasing speed 0 7 8 15 16 23 24 31 32 39 40 47 48 55 56 63 3 Color Wheel n 064U 071 Gobo 7 shake slow to fast 4 Gobo Wheel 072U 079 Gobo 6 shake slow to fast 080U 087 Gobo 5 shake slow to fast 088U 095 Gobo 4 shake slow to fast 096U 103 Gobo 3 shake slow to fast 104U 111 Gobo 2 shake slow to fast 1120 119 Gobo 1 shake slow to fast 120U 127 Open 128U 191 Cycle effect with increasing speed 192U 255 Reverse cycle effect with increasing speed 000U 007 No function 008 119 Rotation effect with increasing speed 120U 231 Reverse rotation effect with increasing speed 232U 255 Gobo bounce 5 Gobo Rotation Intimidator Spot 255 IRC User Manual Rev 3 Page 13 of 24 DMX8CH Channel Function Value Percent Setting cont Configuration Standalone Sound Active Mode Sound Sensitivity Automatic Mode Totem Mode Page 14 of 24 E 000U 015 Open 016U 255 Prism on 000 003 Closed 004U 007 Open 8 Shutter ar 008U 215 Strobe effect with increasing speed 216U 255 Open Set the product in one of the standalone modes to control without a DMX controller Connect the product to power Never connect a product that is operating in any standalone mode either Automatic or Sound Active to a DMX string connected to a DMX controller Product
10. ate MOG ous e Bes Oia a Dare Mi le Pe gO aid Doge in OES A ROR 14 A ae OE ae a O eee Peer et eC Een 14 MARES NO ea nen 15 Patty IMPONEN NOM o e a ora e e ects 15 RanTIL Angle RANGE sos esas sc do lactosa 15 A ate E ve asimaseeeate nae E A aaeteeeeiatees 16 A eE A E S 16 SV SLE UM INOA AP A 16 Master SlaVe Mode EE EE E EE AN E E ae 17 NWO GE EEEE at o lod nea a lo a NS 18 IRG GODSON es e oo a a A NS 18 zero Adjust MOG E en ds od 19 Chandno GODOS siirrt e NN 20 6 Technical INTO MAD ON aii 21 ProdtictMaldten aC los 21 Tz Technical Specification S rin divers stlisawetevier elie 22 PROTEINS co hoses seen a eto as teat teases eee ore hee eas et 23 GOP TAGES a 24 Page 2 of 24 Intimidator Spot 255 IRC User Manual Rev 3 1 BEFORE YOU BEGIN What ls Intimidator Spot 255 IRC Power Cord Hanging Bracket with Mountin Warranty Card Included gig g y Hardware Quick Reference Guide Unpacking Carefully unpack the product immediately and check the container to make sure all the Instructions parts are in the package and are in good condition Claims f the box or the contents the product and included accessories appear damaged from shipping or show signs of mishandling notify the carrier immediately not Chauvet Failure to report damage to the carrier immediately may invalidate your claim In addition keep the box and contents for inspection For other issues such as missing components or parts damage not related to shipping or
11. concealed damage file a claim with Chauvet within 7 days of delivery Text Convention Meaning Conventions 1 512 A range of values 50 60 A set of values of which only one can be chosen Settings A menu option not to be modified Menu gt Settings A sequence of menu options to be followed lt ENTER gt A key to be pressed on the product s control panel ON A value to be entered or selected Sym bols Symbol Meaning Critical installation configuration or operation information Not following these instructions may make the product not work cause damage to the product or cause harm to the operator Important installation or configuration information The product may not function correctly if this information is not used Useful information ES gt Document The information and specifications contained in this document are subject to change without notice Chauvet assumes no responsibility or liability for any errors or omissions Information that may appear in this manual Chauvet reserves the right to update the existing document or to create a new document to correct any errors or omissions You can download the latest version of this document from www chauvetlighting com Copyright 2015 Chauvet All rights reserved Electronically published by Chauvet in the United States of America Author Date Editor Date A Leon 06 23 2015 R Isenstadt 06 23 2015 Intimidator Spot 255 IRC User Manual Rev 3 Page 3 of 24 Product ata
12. duct s housing are blocked Never connect the product to a dimmer or rheostat Make sure to replace the fuse with another of the same type and rating Never carry the product from the power cord or any moving part Always use the hanging mounting bracket The maximum ambient temperature Ta is 104 F 40 C Do not operate the product at higher temperatures In the event of a serious operating problem stop using the product immediately Never try to repair the product Repairs carried out by unskilled people can lead to damage or malfunction Please contact the nearest authorized technical assistance center To eliminate unnecessary wear and improve its lifespan during periods of non use completely disconnect the product from power via breaker or by unplugging it Keep this User Manual for future use If you sell the product to another user be sure to give this document to the next owner Intimidator Spot 255 IRC User Manual Rev 3 2 INTRODUCTION Product Overview M anual Focus Lens a el Gobo Access Door Cooling Fan Pi y LCD Display IR Sensor Indicator LED Menu Buttons Front Panel View Power Out Microphone DMX In Out Power In Back Panel View Fuse Holder Intimidator Spot 255 IRC User Manual Rev 3 Page 5 of 24 Product Dimensions Page 6 of 24 Intimidator Spot 255 IRC User Manual Rev 3 3 SETUP AC Power The Intimidator Spot 255 IRC has an auto ranging power su
13. e DMX input of the first slave product to the DMX output of the master 9 Connect the DMX input of the subsequent slaves to the DMX output of the previous slave 10 Finish setting and connecting all the slaves Master 1 Set the master to operate in either Automatic or Sound Active mode 2 Make the master the first product in the DMX daisy chain A ee a eae When including Intimidator Spot LED 250 products in Master Slave configuration with Intimidator Spot 255 IRC products you must observe the following 255 IRC is connected as a slave the Intimidator Spot 255 IRC must be set to DMX mode with a starting address of 001 DO NOT set the Intimidator Spot 255 IRC in Slave mode when an Intimidator Spot LED 250 is the master The Intimidator Spot 255 IRC will not operate as the master to an Intimidator Spot LED 250 connected as a slave When the Intimidator Spot LED 250 is the master and the Intimidator Spot Configure all the slaves before connecting the master to the DMX daisy chain Never connect a DMX controller to a DMX string configured for Master Slave operation because the controller may interfere with the signals from the master Do not connect more than 31 slave units to the master Intimidator Spot 255 IRC User Manual Rev 3 Page 17 of 24 IR Mode IR mode allows the product to be controlled with an infrared remote controller The IRC 6 can remotely set the product to various modes adjust the
14. formation Technical Support Address 5200 NW 108th Avenue Voice 954 577 4455 Press 4 Sunrise FL 33351 Fax 954 756 8015 Voice 954 577 4455 Email tech chauvetlighting com Fax 954 929 5560 Toll free 800 762 1084 World Wide Web www chauvetlighting com UNITED KINGDOM AND IRELAND Chauvet Europe Ltd General Information Technical Support Address Unit 1C Email uktech chauvetlighting com Brookhill Road Industrial Estate Pinxton Nottingham UK World Wide Web _ www chauvetlighting co uk NG16 6NT Voice 44 0 1773 511115 Fax 44 0 1773 511110 MEXICO Chauvet Mexico General Information Technical Support Address Av Santa Ana 30 Email servicio chauvet com mx Parque Industrial Lerma Lerma Mexico C P 52000 World Wide Web www chauvet com mx Voice 52 728 285 5000 CHAUVET EUROPE Chauvet BVBA General Information Technical Support Address Stokstraat 18 Email Eutech chauvetlighting eu 9770 Kruishoutem Belgium World Wide Web www chauvetlighting eu Voice 32 9 388 93 97 Outside the U S United Kingdom Ireland Mexico or Benelux contact the dealer of record and follow their instructions to request support or to return a product Visit the Chauvet website for contact information Intimidator Spot 255 IRC User Manual Rev 3
15. her products You can power link up to 6 Intimidator Spot 255 IRC units on 120 VAC or up to 10 Intimidator Spot 255 IRC units on 230 VAC The power linking diagram shown above corresponds to the North American A version of the product ONLY If using the product in other markets you must consult with the local Chauvet distributor as power linking connectors and requirements may differ in your country or region Intimidator Spot 255 IRC User Manual Rev 3 Page 7 of 24 Mounting Orientation Rigging Mounting Diagram Page 8 of 24 Before mounting the product read and follow the safety recommendations indicated in the Safety Notes The Intimidator Spot 255 IRC may be mounted in any position however make sure adequate ventilation is provided around the product Before deciding on a location for the product always make sure there is easy access to the product for maintenance and programming purposes Make sure that the structure or surface onto which you are mounting the product can support the products weight See the Technical Specifications for weight information The CLP 15 clamp from Chauvet is appropriate for this product When mounting the product overhead always use a safety cable Mount the product securely to a rigging point whether an elevated platform or a truss When rigging the product onto a truss you should use a mounting clamp of appropriate weight capacity When power linking multiple products
16. his product f ON The list below describes which features each button controls o Intimidator Spot 255 IRC User Manual Rev 3 Zero Adju St The Intimidator Spot 255 IRC contains a passcode protected mode which allows you to Mode calibrate and adjust several of the product s operating parameters In order to access this mode do the following 1 Press and hold lt MENU gt for at least 10 seconds 2 Use lt UP gt and lt DOWN gt to enter the passcode 2323 3 Press lt ENTER gt In this mode there are several options for adjustment Parameter Default Description Pan TS Manually adjust the starting pan angle Tilt 095 Manually adjust the starting tilt angle Gobo 1200 Manually adjust the gobo wheel starting position Color NT Manually adjust the color wheel starting position Prism 128 Manually adjust the prism starting position LED 000 Manually adjust the starting brightness of the LED Intimidator Spot 255 IRC User Manual Rev 3 Page 19 of 24 Changing To change the gobos in the Intimidator Spot 255 IRC do not remove the gobo wheel Simply Gobos 1 Disconnect product from power outlet 2 Place the product on a flat level surface with the front facing up 3 Access the gobo plate by removing the cover on the moving head By hand gently push downward on the cover in the direction of the debossed arrowhead on the cover 4 Rotate the gobo wheel until the gobo that needs replacing is accessible 5
17. ions below 1 Press lt MENU gt 2 Use lt UP gt or lt DOWN gt to choose Run Mode 3 Press lt ENTER gt 4 Use lt UP gt or lt DOWN gt to select Manual Test 5 Press lt ENTER gt 6 Use lt UP gt or lt DOWNS to select the function to test or control from the options Pan Pan Fine Tilt Tilt Fine P T Speed Color Gobo Gobo Rot Prism Dimmer Shutter Special Functions and P T Macros 7 Press lt ENTER gt 8 Use lt UP gt or lt DOWN gt to change the value of the selected function from 000 255 NOTE For information regarding what each value range does for each function see the DMX Assignments for 13CH Mode Pan Tilt To select whether the Intimidator Spot 255 IRC will operate with normal panning or Orientation inverted panning do the following Press lt MENUS gt Use lt UP gt or lt DOWN gt to choose Setup Press lt ENTER gt Use lt UP gt or lt DOWN gt to select Pan Reverse Press lt ENTER gt Use lt UP gt or lt DOWN gt to select ON or OFF Press lt ENTER gt To select whether the Intimidator Spot 255 IRC will operate with normal tilting or inverted tilting do the following Press lt MENU3 gt Use lt UP gt or lt DOWN gt to choose Setup Press lt ENTER gt Use lt UP gt or lt DOWN gt to select Tilt Reverse Press lt ENTER gt Use lt UP gt or lt DOWN gt to select ON or OFF Press lt ENTER gt RE oe A O Pan Tilt Angle The user can select the
18. l of pan Fine control of tilt Pan Tilt speed fast to slow white Yellow 021U 027 Green Rec Light Blue Kelly Green Orange Dark Blue White Yellow 6 Color Wheel Yellow Pink Pink Green 086 092 Green Red Red Light Blue Light Blue Kelly Green Kelly Green Orange Orange Dark Blue Dark Blue White 128U 191 Color cycling rainbow with increasing speed 1920 255 Reverse color cycling rainbow with increasing speed O11 ND 00 32 39 40 47 48 55 064U 071 Gobo 7 shake 7 Gobo Wheel 072 079 Gobo 6 shake 080 087 Gobo 5 shake 088U 095 Gobo 4 shake 096U 103 Gobo 3 shake 104U 111 Gobo 2 shake 112U 119 Gobo 1 shake 120U 127 Open 128U 191 Cycle effect with increasing speed 192U 255 Reverse cycle effect with increasing speed No function Rotation effect with increasing speed Reverse rotation effect with increasing speed 232U 255 Gobo bounce slow to fast slow to fast slow to fast slow to fast slow to fast slow to fast ATAR ASS AS AS AS A A gt gt slow to fast 8 Gobo Rotation Intimidator Spot 255 IRC User Manual Rev 3 Page 11 of 24 DMX13CH_Shanne cont 9 10 11 12 13 Page 12 of 24 Function Value Percent Setting 000 015 Open 016U 255 Prism on Closed Open Strobe effect with increasing speed Open 000 007 No function 008U 027 Blackout while pan tilt moving 028U 047 Blackout while moving gob
19. ne control of tilting P TSpeed i Pan Tilt speed fast to slow Selects color options Manual Test Selects gobo options ana Rot Rotation effect with increasing speed Selects 3 facet prism Sets dimmer value Strobe effect with increasing speed ee Special Function Selects control functions P TMacro Macro Selects pan tilt macros Pan Reverse m oe Normal pan operation Pan Reverse o Reverse pan operation eders OFF Normaltilt operation ON Reverse tilt operation OFF Normal display Screen Reverse ON a 50 Selectsthe540 pan angle range Pan Angle 360 Selects the 360 pan angle range Setup 180 Selects the 180 pan angle range Selects the 270 tilt angle range Tilt Angle 180 Selects the 180 tilt angle range PF 090 es Selects the 90 tilt angle range OFF Turms off Totem mode Totem Mode UP Selects upward pan and tilt range Selects downward pan and tilt range Sets sound sensiiviy po Reset Resets the product roads factory defaul Displays the sofware version Svinte Displays the current running mode Displays the current DMX address Temperature XXX Displays the LED temperature in Celsius Intimidator Spot 255 IRC User Manual Rev 3 Page 9 of 24 Configuration Set the product in DMX mode to control with a DMX controller DMX 1 Connect the product to a suitable power outlet 2 Connect a DMX cable from the DMX output of the DMX controller to the DMX input socket on the produc
20. o wheel 0480 067 ae blackout while pan tilt moving gobo 068U 087 Blackout while moving color wheel 0880 107 Disable blackout while pan tilt moving color wheel 1080 127 ETE blackout while moving gobo color Special Function wnee 128 147 Disable blackout while pan tilt moving gobo moving color wheel Reset pan Reset tilt Reset color wheel Reset gobo wheel Reset prism Reset all channels No function No function Automatic movement 1 Automatic movement 2 Automatic movement 3 Automatic movement 4 Automatic movement 5 Automatic movement 6 Automatic movement 7 Pan Tilt Macros 120U 135 Automatic movement 8 1360 151 Sound active movement 1 152U 167 Sound active movement 2 168 183 Sound active movement 3 184U 199 Sound active movement 4 200U 215 Sound active movement 5 216U 231 Sound active movement 6 232U 247 Sound active movement 7 248U 255 Sound active movement 8 Intimidator Spot 255 IRC User Manual Rev 3 DMX8CH_ hanne Function Value Percent Setting 1 000U 255 0 540 2 Tilt 000U 255 0 270 000U 006 White 007U 013 Yellow 014U 020 Pink 021U 027 Green 028U 034 Red 035U 041 Light Blue 042U 048 Kelly Green 0490 055 Orange 056U 064 Dark Blue 065U 071 White Yellow 072U 078 Yellow Pink 079 085 Pink Green O86U 092 Green Red 093 099 Red Light Blue 100U 106 Light Blue Kelly Green 107U 113 Kelly Green Orange 1140 120 Orange Dark Blue 121U 127 D
21. pply and it can work with an input voltage range of 100 to 240 VAC 50 60 Hz To determine the product s power requirements circuit breaker power outlet and wiring use the current value listed on the label affixed to the product s back panel or refer to the products specifications chart The listed current rating indicates the product s average current draw under normal conditions Always connect the product to a protected circuit circuit breaker or fuse Make sure the product has an appropriate electrical ground to avoid the risk of electrocution or fire To eliminate unnecessary wear and improve its lifespan during periods of non use completely disconnect the product from power via breaker or by unplugging it i Never connect the product to a rheostat variable resistor or dimmer circuit even if the rheostat or dimmer channel serves only as a 0 to 100 switch Fuse 1 Disconnect the product from power Replacement Using a flat head screwdriver unscrew the fuse holder cap from the housing 3 Remove the blown fuse 4 Replace with a fuse of the same type and rating 5 Screw the fuse holder cap back in place and reconnect power A Disconnect the product from power before replacing the fuse Always replace a blown fuse with another of the same type and rating N Power Linking The product provides power linking via the IEC outlet located in the back of the unit O O Power Linking a Diagram a 2 Product Ot
22. s in standalone mode may transmit DMX signals that could interfere with the DMX signals from the controller To enable the Sound Active mode do the following 1 Press lt MENU gt Use lt UP gt or lt DOWN gt to choose Run Mode Press lt ENTER gt Use lt UP gt or lt DOWN gt to select Sound Press lt ENTER gt DE de The product will only respond to low frequencies of music bass and drums To set the sound sensitivity do the following Press lt MENU gt Use lt UP gt or lt DOWN gt to choose Setup Press lt ENTER gt Use lt UP gt or lt DOWN gt to select Sensitivity Press lt ENTER gt Use lt UP gt or lt DOWN gt to select 001 100 low to high Press lt ENTER gt Id R en To enable the Automatic mode follow the instructions below Press lt MENUS gt Use lt UP gt or lt DOWN gt to choose Run Mode Press lt ENTER gt Use lt UP gt or lt DOWN gt to select Auto Press lt ENTER gt SS DA To activate the Totem Mode do the following Press lt MENU gt Use lt UP gt or lt DOWN gt to choose Setup Press lt ENTER gt Use lt UP gt or lt DOWN gt to select Totem Mode Press lt ENTER gt Use lt UP gt or lt DOWN gt to choose OFF DOWN or UP Press lt ENTER gt E A A IAS Intimidator Spot 255 IRC User Manual Rev 3 Manual Test Mode To test or control any function of the Intimidator Spot 255 IRC through the LCD display menu follow the instruct
23. t Starting Address When selecting a starting DMX address always consider the number of DMX channels the selected DMX mode uses If you choose a starting address that is too high you could restrict the access to some of the product s channels The Intimidator Spot 255 IRC uses up to 13 DMX channels in its 13 channel DMX mode which defines the highest configurable address to 500 If you are not familiar with the DMX protocol download the DMX Primer from www chauvetlighting com To select the starting address do the following DMX Personalities Page 10 of 24 aa oY Press lt MENU3 gt Use lt UP gt or lt DOWN gt to choose Address Press lt ENTER gt Use lt UP gt or lt DOWN gt to select the starting address Press lt ENTER gt The Intimidator Spot 255 IRC has two DMX personalities a 13 channel personality and an 8 channel personality To choose which DMX personality to use follow the steps below SAP one D Press lt MENU gt Use lt UP gt or lt DOWN gt to choose Run Mode Press lt ENTER gt Use lt UP gt or lt DOWN gt to select DMX Press lt ENTER gt Use lt UP gt or lt DOWN gt until either DMX13CH to choose the 13 channel personality or DMX8CH to choose the 8 channel personality shows on the display Press lt ENTER gt Intimidator Spot 255 IRC User Manual Rev 3 3 DMX ASSIGNMENTS DMX13CH Channel Function Value Percent Setting FinePan 0000 255 Fine contro
24. timidator Spot 255 IRC do the following 1 Press lt MENU gt 2 Use lt UP gt or lt DOWN gt to choose Setup 3 Press lt ENTER gt 4 Use lt UP gt or lt DOWN gt to choose Reset or Factory Set 5 Press lt ENTER gt System To view information about the Intimidator Spot 255 IRC 3 Press lt MENU gt Use lt UP gt or lt DOWN gt to choose Sys Info Press lt ENTER gt The current information about the product will show on the display Intimidator Spot 255 IRC User Manual Rev 3 Master Slave The Master Slave mode allows a single Intimidator Spot 255 IRC the master to Mode control the actions of one or more Intimidator Spot 255 IRC products the slaves without the need of a DMX controller The master will be set to operate in either Automatic or Sound Active mode while the slaves will be set to operate in Slave mode Once set and connected the slaves will operate in unison with the master Configure the products as indicated below Slaves Press lt MENU gt Use lt UP gt or lt DOWN gt to choose Run Mode Press lt ENTER gt Use lt UP gt or lt DOWN gt to select Slave Press lt ENTER gt Use lt UP gt or lt DOWN gt to select Slave1 Slave2 Slave3 or Slave4 Select Slave1 for 100 synchronized actions Select Slave2 Slave3 or Slave4 for a delayed show with all heads in the same direction but with a delay creating a wave effect 7 Press lt ENTER gt 8 Connect th
25. u should clean your lighting products at least twice a month However be aware that usage and environmental conditions could be contributing factors to increase the cleaning frequency To clean the product follow the instructions below 1 Unplug the product from power 2 Wait until the product is at room temperature 3 Use a vacuum or dry compressed air and a soft brush to remove dust collected on the external surface vents 4 Clean all glass transparent surfaces with a mild soap solution ammonia free glass cleaner or isopropyl alcohol 5 Apply the solution directly to a soft lint free cotton cloth or a lens cleaning tissue 6 Softly drag any dirt or grime to the outside of the glass transparent surface 7 Gently polish the glass transparent surfaces until they are free of haze and lint i Always dry the glass transparent surfaces carefully after cleaning them Do not spin the cooling fans using compressed air because you could damage them Intimidator Spot 255 IRC User Manual Rev 3 Page 21 of 24 7 TECHNICAL SPECIFICATIONS Dimensions and Weight Power Light Source Photometrics Thermal DMX Ordering Page 22 of 24 Length 8 3 in 211 mm Width 9 1 in 232 mm Height pointing upward 13 2 in 837 mm Note Dimensions in inches rounded to the nearest decimal digit Power Supply Type Switching internal Parameter Consumption Operating Power linking current units Fuse Po
26. wer I O Power input connector Power output connector Power Cord plug Type LED Color White Parameter Illuminance Beam angle Strobe Rate Pan and Tilt Pan Tilt Ranges Gobo Size Maximum External Temp 104 F 40 C I O Connectors 3 pin XLR Product Name Intimidator Spot 255 IRC Range 100 to 240 VAC 50 60 Hz 120 V 60 Hz 98 W 1 4A 8 A 6 units F 3A 250 V US Worldwide IEC Edison Edison US Power 60 W Quantity 1 10 420 lux 2m 15 0 to 20 Hz 540 Pan 540 360 180 Pan 24 mm outside 20 mm image 1 1 mm maximum thickness Cooling System Fan cooled Connector Type Sockets Item Code 08010959 Weight 12 6 lb 5 7 kg Voltage Selection Auto ranging 230 V 50 Hz 95 W 0 8A 8 A 10 units F3A 250 V UK Europe IEC IEC Local plug Lifespan 50 000 hours Current 2 3A 270 Tilt 270 180 90 Tilt Channel Range 8or 13 UPC Number 781462213077 RoHS Intimidator Spot 255 IRC User Manual Rev 3 To return a product or request support In the U S contact Chauvet World Headquarters See Contact Us In the UK or Ireland contact Chauvet Europe Ltd See Contact Us In Mexico contact Chauvet Mexico See Contact Us In Benelux contact Chauvet Europe BVBA See Contact Us In any other country DO NOT contact Chauvet Instead contact your lighting distributor See www chauvetlighting com for distributors outside the U S UK
Download Pdf Manuals
Related Search