Home

APX32EN Security System Quick Start Guide

image

Contents

1. K14117 8 11 07 Rev APX32EN APXALARM UL ALARM Security System Quick Start Guide APX32EN is not intended for UL985 Household Fire applications unless a 24 hour backup battery P N LYNXRCHKIT HC or LYNXRCHKIT SHA is installed Introduction This Quick Start Guide can help you install the rechargeable APX32EN quickly and easily by providing the basic steps for installation using the built in defaults For more detailed information and important notes refer to the APX32EN Installation and Setup Guide Installing APX32EN Installation and Electrical Connections Step Action 1 Install the control as follows a Separate the front assembly from the back plate and disconnect the cable from the front assembly board Note Disconnect the cable only from the front assembly board not from the terminal block PC board b Mount the back plate 2 Make wiring connections as follows a Connect the incoming phone line to either the 8 position jack or terminals 2 TIP and 3 RING b Connect the handset phone lines to either the RJ11 jack or terminals 4 TIP and 5 RING Note For full line seize operation see the installation instructions If used connect a piezo sounder to terminals 10 and 11 d If used connect a bell to terminals 11 and 12 e lfused connect the IP or GSM communications device to the Alarmnet LRR IP communications port f Connect wires from the K10145X10 AC Tr
2. various system functions Interactive Mode Programming Interactive Mode Used to Program 56 Enhanced Zone Programming Zone characteristics report codes and serial numbers 83 Enhanced Sequential Mode 5800 Series transmitter serial numbers 84 Assign Zone Voice Descriptors Voice descriptors for each zone Remote Programming Downloading Perform site initiated downloader session to load central station ID by Installer Code 7 1 APX32EN PROGRAMMING DEFAULT TABLES For programming data values and Powerline Carrier Devices other than those listed in the default tables see the Installation Instructions Function DefauttValue 4112 3 11 1 15 15 15 15 30 Daylight saving time start end weekend 2 7 3 44 Secondary subscriber account number 46 Follow Me Reminder Phone Number 47 Phone system select 48 Report format for primary secondary 7 49 Split dual reporting 50 15 second dialer delay burglary 51 Periodic test report 52 First test report offset 53 Sescoa radionics select 54 Lack of usage notification 55 Reporting channels 56 Enhanced zone programming See 56 table 1 1 1 1 1 1 1 1 5 2 7 i i i 1 1 1 0 0 T 0 0 0 0 0 0 74 Low battery restore report code 0 75 RFtransmitter low battery restore report code 0 76 Test restore report code 78 Programmable Tone Generation Time 80 Powerline Carrier Devices See 80 table See 81 table 81
3. user number User s Code see note below To delete a User Code except Master Code Master Code user number To turn Test mode on User Code To turn Test mode off User Code To use the defined AUX function Press and hold key 2 secs 4 beeps User Code To define the AUX function refer to the procedure in the Aux Function section of the User Manual Note The 1 button paging feature field 87 is not enabled with the default programming To program Follow Me reminder telephone number User Code FUNCTION 65 To delete Follow Me reminder telephone number User Code FUNCTION 65 Remote Phone Control Operation To remotely disarm system C 1 To remotely arm in AWAY mode C C 2 To remotely arm in STAY mode C C C 3 To remotely arm in AWAY or STAY with NO 2 3 0 To remotely bypass a zone e 6 zone no To remotely activate forced bypass L C 6 Note Force bypass option must be enabled To remotely check system status To end remote phone session Hang upor 19 Speaker Phone Operation Note The ARMED and READY LEDs blink alternately when the Speaker Phone feature is active To place a call or answer a call using the speaker phone 4 To Flash switch between two calls using call waiting To hang up and exit speaker phone mode To enable disable toggle ringer 4 V
4. BG 5 5S 9 YOU MUST ENROLL suns SY LOOP 1 LOOP LOOP THIS BUTTON LOOP 1 1 1 X V LOOP 1 5800CO 5800RL 5800WAVE 5801 5802 MN 5802 MN2 5804 5804 5804BD 5804BDV ENROLL AS RF SET PROGRAM ENROLL AS ENROLL AS ENROLL AS ENROLL AS BR BR HOUSE ID HOUSE ID UR OR UR OR RE UR OR RF PROGRAM HOUSE ID LOOP 1 LOOP2 PRIMARY REED LOOP2 AUX LOOP 1 CENTER LOOP 1 LOOP 1 T TERMINALS TERMINALS TEMP LOOP 1 LOOP 1 ALTERNATE SENSOR LOOP3 POSITION AUX FOR LOOP 2 RIGHT 5806 5807 5808 5808LST 5809 5814 5816 5816MN 5816TEMP 5817 ENROLL AS ENROLL AS RF ENROLL AS RE ENROLL AS RF ENROLL AS RF ENROLL AS RF ENROLL AS RF 1 2 2 LOOP2 b REED REED LOOP 1 LOOP 3 LOOP 1 MOTION TERMINALS LOOP 1 SOUND 9 INTERNAL SHOCK LOOP 1 SENSOR LOOP3 TERMINALS TERMINALS 5818 5819 5819S WHS amp BRS 5828 5828V 5849 5850 GBD 5890 5890PI ENROLL AS RF ENROLL AS RF ENROLL AS RF PROGRAM ENROLL AS RF ENROLL AS RF ENROLL AS RF HOUSE ID 09012 013 VO Notes 1 Loop 4 must always be enrolled on the 5801 5804 5804BD 5804BDV and 5804E transmitters 2 5804E encrypted High Security devices must be activated while the system is in Go No Go Test Mode Refer to the transmitter s installation instructions for complete details The system will confirm enrollment of the encrypted device by beeping two times Keypad Functions when default programm
5. Zone lists for devices 3 2 1 95 Ring detect count for downloading remote phone control 1 2 3 4 By activating 96 Field 43 and 44 will be changed to 15 15 15 15 5 on a Zone Default Value 2 front door 3 back door 4 window 5 motion detector 67 9i cce 26 loop 3 arm away 27 loop 2 disarm 28 loop 4 arm stay 29 loop 1 no alarm response 30 loop 3 arm away 31 loop 2 disarm 32 loop 4 arm stay 33 loop 1 no alarm response 92 duress 99 silent alarm NOTES e Table 1 supports a Powerline Carrier Device programmed as device 8 which closes and stays closed upon burglary alarms and restores after bell timeout For other applications or actions e g using a pulsing siren see the 80 Device Programming Menu Mode section of the Installation Instructions e Primary report format is Ademco s Contact ID reporting Table 1 records only alarms alarm restores troubles and trouble restores in the event log 5800 Series Transmitter Loop Numbers The following illustration shows the compatible transmitters and their associated input types and loop designations UL The 5800CO 5800RL 5802MN 5802MN2 5804 5804BD 5804BDV 5804E 5814 5816TEMP 5819 5819S WHS amp BRS 5828 5828V and 5850 GBD wireless transmitters have not been evaluated by UL LOOP 3 LOOP T gt YOU MUST e 2 ENROLL NN LOOP 2 A Dy
6. ABLE HANDSET INCOMING PHONE ALL OUTPUT CIRCUITS ARE POWER LIMITED LINE LINE EARTH FUTURE A WARME GROUND PHONE USE GND SOUNDERS PLCD AC 1 TOPREVENT Il m m 0 p pL 4 1 RISK OF SHOCK DISCONNECT 8 TELEPHONE LINE Ru POS ATTELECOM JACK JACKBEFORE l SERVICING i TIP RING TIP RING THISUNIT 1 o RO Dueb 9 o Ya 5 LRR IP COMMUNICATIONS gt lt zc PORT 8 25 GSML GSMVL COMMUNICATIONS PORT INCOMING TELEPHONE STANDARD LINE HIGH CAPACITY PREMISES BATTERY CONNECTOR TELEPHONE K10145X10 PLUG IN SUPER HIGH CAPACITY x TRANSFORMER BATTERY CONNECTOR q 2 BELL mi 6 14VDC Q AC EARTH FOTONI S 30mA max GROUND 6 14VDC AC 120mA max g WAVE2EX eg SYNC i 1 THE CONTROL IS COMPATIBLE WITH THE WEEKLY TESTING IS FOLLOWING INTEGRAL RECHARGEABLE REQUIRED TO ENSURE BATTERY PACKS PROPER OPERATION P N LYNXRCHKIT SC OFTHIS SYSTEM I DATA P N LYNXRCHKIT HC NOTE 1 P N LYNXRCHKIT SHA USE ONLY THE K10145X10 X10 REPLACE EVERY FOUR YEARS TRANSFORMER PROVIDED ONLY CONNECTIONS WHEN AVAILBLE APX32EN WIRING CONNECTIONS 2 09012 010 VO System Programming For advanced interactive mode programming refer to the end of the System Programming procedure Step Action 1 Enter Programming mode Installer Code 8 00 2 Set a programming default as follows Press 97 then press number 1 to sel
7. OLUME To return the keypad to telephone mode after disarming the system 4 Note The Babysitter Code and Installer Code cannot disarm the system unless it was the code used to arm the system In addition if the system is armed by pressing and holding the Quick Arm buttons neither the Babysitter Code nor the Installer Code can disarm the system REFER TO THE INSTALLATION AND SETUP GUIDE FOR THE LIMITATIONS OF THIS SYSTEM AND WARRANTY INFORMATION cH _ APXALARM SECURITY SOLUTIONS 5132 North 300 West Provo Utah 84604 800 216 5232 www apxalarm com K1 A 4117 8 11 07 Rev
8. ansformer to terminals 15 and 16 Make battery connections as follows Remove battery retainer Remove backing from tape on back plate Insert battery pack into back plate Install battery retainer Connect battery connector to receptacle on terminal block PC board Carefully reconnect the ribbon cable to the front assembly PC board connector properly aligning the red wire g After all wiring connections have been made snap the front assembly to the back plate so it is held by the locking tabs h Plug the transformer into a 24 hour 110VAC unswitched outlet Note Rechargeable batteries may take up to 48 hours to fully charge LOW BAT message should clear within four hours or by entering Test Mode oo00c0P RETAINER NOTE LYNXRCHKIT HC BATTERY PACK SHOWN LOCKING TABS E oq a A wb es PADS D BATTERY LOCKING TABS LOCKING TABS 09012 002 VO BATTERY RECEPTACLE WIRING TERMINALS 09012 00 UL NOTE THE MINIMUM WIRE SIZE USED FOR TELEPHONE LOCAL SOUNDER DISABLE SHUNT TO 1 INSTALLATIONS MUST BE 26 GAUGE REMOVE TO DIS
9. ect default table Refer to APX32EN Programming Default Tables 3 Program the variable data fields as follows a RF House ID Press 24 then enter the desired 2 digit RF House ID for wireless keypads b PABX Access Code if used Press 40 then enter up to 6 digits If fewer than 6 digits are used press to end the field and advance to the next field c Primary Phone Number Press 41 then enter the primary phone number up to 20 digits If fewer than 20 digits are used press to end the field and advance to the next field d Secondary Phone Number if used Press 42 then enter the secondary phone number up to 24 digits If fewer than 24 digits are used press to end the field and advance to the next field e Primary Account Number if used Press 43 then enter the primary account number If only 3 digits are used press to end the field and advance to the next field f Secondary Account Number if used Press 44 then enter the secondary account number If only digits are used press to end the field and advance to the next field g Download Phone Number Press 94 then enter the downloading computer phone number up to 20 digits If fewer than 20 digits are used press to end the field 4 Enhanced Sequential Mode Press 83 then follow the prompts as follows a Zone Number Enter 2 digit zone number of the first transmitter to have its serial number entered The system will announce the V
10. ing is used Security Functions Checking system status high level messages press again for secondary messages To arm in STAY mode Press and hold down or enter your code See note below To restart exit delay applies only if system is armed in Stay mode and Quick Exit option has been enabled To arm in AWAY mode Press and hold down or enter your code See note below To arm with NO DELAY User Code or OR User Code or To disarm the system and silence alarms User Code See note below Note During Entry Delay or when an Alarm Condition exists the system can be disarmed by entering the User Code Entering the key is not required To bypass a zone s User Code BYPASS 2 digit zone number s To turn Chime mode on or off FUNCTION CHIME Message Center To record a message To stop recording before end of 85 seconds To play back a message To skip a message gt To delete all messages FUNCTION DELETE during message replay Volume Control To adjust message playback system announcement volume 8 Up or 6 Down To mute system announcements To restore unmute announcements amp volume 3 or 6 Note If the system was muted during Field Programming it will be unmuted upon exiting Other Functions To set the time and date User Code 63 To program scheduled events User Code 64 then follow procedure in User Manual To add a User Code Master Code
11. l be displayed Note This point can be faulted and restored and the panel will listen for the transmission 4 The serial number loop number combination that was entered can be confirmed by faulting and restoring the zone being entered If the panel receives a transmission that matches the serial number and loop number entered the keypad will beep three times and C will be displayed This indicates that the serial number transmission has been confirmed to match No further transmissions will be received Note When confirming a 4 button key it assumed that all loops are used and only the serial number is confirmed Pressing any key will allow a confirm Two beeps indicate that the template has been accepted A single long beep indicates illegal entries or duplicate serial number loop entry 5 When the last zone has been entered the display will remain on that zone To exit this mode and return to data field program mode press 00 at the ZONE NUMBER prompt 6 Once all zones have been programmed test each zone using the system s Test mode Do not use the Transmitter ID Sniffer mode for this since it will only check for transmission of one zone on a particular transmitter and not the zones assigned to each additional loop sg Step Action c Serial Number This prompt can be used to enroll the transmitter serial number via RF ent transmission or manually If using RF Learning proceed to c 1 If usi
12. ng the manual mode skip to c 2 1 RF Learning Two 2 transmissions two key depressions at least five second apart will be required for BR type or four 4 transmissions fault restore and fault restore for UR or RF type BR type devices can be enrolled only by transmission from BR devices Likewise UR and RF devices can only be enrolled by transmission from a UR or RF device If the learned serial number has a different loop number than that entered in 56 the system will announce the Voice Descriptor if it is programmed followed by two beeps and will return to Prompt 1 and L will be displayed If the loop number captured by RF transmission and that entered in 56 mode match the system will announce the Voice Descriptor if it is programmed followed by three beeps and return to Prompt 1 and LC will be displayed No additional transmissions are needed for confirmation Note BR type devices can be enrolled only by transmission from BR devices Likewise UR and RF devices can only be enrolled by transmission from a UR or RF device ib 2 Manual Entry Enter the 7 digit serial number printed on the transmitter If you enter an incorrect digit press the key to backup to prompt 1A and start over When all seven digits are entered press the key 3 Once all 7 digits have been entered press the key If less than 7 digits are entered the keypad will emit a single long beep and return to the 1 prompt witho
13. oice Descriptor for the selected zone number if it is programmed Press to continue Starting with this zone the system will search for the first transmitter which has all of the following attributes pre programmed in Zone Programming 1 The correct input type selected in 56 RF UR or BR programmed 2 correct loop number selected in 56 3 No serial number programmed 4 Zonetype Notes 1 If the first zone number entered does not have one or more of the above attributes the system will search its database for the first zone that does and will display it at the ENROLL SERIAL NUMBER prompt 1b 2 Pressing 00 exits mode upon which the prompt 83 blinks indicating the mode is inactive b Enroll Mode If L is displayed the serial number for this transmitter has already been entered however it may still be confirmed viewed or deleted 1 If the transmitter s serial number has not been previously entered enter the enroll serial number mode now by pressing 1 or copy the last serial number that was entered by pressing 2 5 r m 2 Ifthe transmitter s serial number has been previously entered it may be viewed by pressing 3 or deleted by pressing 9 Note If view is selected each digit will be re displayed and the keypad will beep once for digits 1 6 and three times for the last digit 3 Once the serial number has been entered the system will return to the 1A prompt and L wil
14. ut displaying the L If more than 7 digits have been entered the first 6 digits will be saved along with the last digit that was entered entering 123456789 yields the serial number 1234569 Note If 52 seconds passes and no entry has been made the system returns to prompt 1 d Delete Serial Number This prompt can be used to delete the serial number programmed for the zone 1 Enter 0 to discard delete request or 1 to confirm 5 Exit Programming mode as follows 98 inhibits re entry into the Programming mode using the Installer Code 99 allows re entry into the Program mode using Installer Code 8 0 0 6 Set RF House ID in the wireless keypads as follows a 5827 wireless keypad Set the keypad s DIP switches to the RF House ID programmed in field 24 7 Set the Real Time Clock as follows a Enter time date setting mode by entering the User Code FUNCTION 63 b The hour prompt is displayed Enter the correct hour then press ADD to accept and advance For each subsequent prompt enter the correct value then press ADD d The system will exit this mode automatically after entering the year and pressing ADD or if no keys are pressed for 1 minute 8 Test the system as follows a After installation and programming enter Installer Code TEST b Toexit Test mode enter Installer Code OFF 9 Assign desired User Codes by following the procedures in the User Guide Show the user how to perform the

Download Pdf Manuals

image

Related Search

Related Contents

LG 55LM6200 Energy Guide : Free Download, Borrow, and Streaming : Internet Archive  WiFi user manual 20150108.cdr  横浜市グリーン購入の推進に関する基本方針 (別記)特定調達物品等  SPANISH MASTER - Franklin Electronic Publishers, Inc.  our User Manual - Construction Estimating Software  User Manual - Hitachi Solutions America  Manual de instrucciones  

Copyright © All rights reserved.
Failed to retrieve file