User`s Manual
Contents
1. 100 R to DVI input port of display Step 7 If you need on site monitoring connect DVI OUT on the front side to DVI input port of local monitor over DVI cable 1 3 Installation Note1 The maximum extension length by multi mode fiber is 500 meters Note2 Be recommended NOT to use any intermediate cable or adapter in between to avoid undesirable performance degradation DVDF 200 On ery Re Pii a U KZ ZD 4o lo a ey NW S2 G4 IX A NS S DVFX 100 DVI Source L i Local Remote DVI Display DVI Display Figure 1 Connection Diagram of DVDF 200 1 4 Installation Self EDID Programming Procedure The graphic source equipment generally requires display information EDID It contains resolution and timing information of the display DVDF 200 supports Self EDID programming It is the procedure that reads the EDID from the display and stores it in the EEPROM of the converter We highly recommend do Self EDID once when you install your system with DVDF 200 for the first time Follow the steps below to do it correctly Note1 If you know that EDID is not required by the user s DVI source Self EDID programming is not necessary Note2 The default EDID in factory ship out is programmed in the VESA standard of WUXGA 1920x1200 60Hz Step 1 Connect 5V power adapter to turn DVDF 200 Step 2 Power LED Blue will be turned ON Step 3 Push the EDID button on the rear side of converter with a narrow pin2. A Locking type Oo User s Manual O Option Product Mounting bracket 1 1 Welcome Product Description System Requirements for Setup O Hardware requirements m You have to have a DVI graphic controller or card having a DVI port in your PC SUN or Mac systems It should support the maximum graphic resolution feature of displays to be connected m No special requirements for memory size CPU speed and chipsets if you ve already properly installed your DVI graphic controllers or cards O Software requirements m No special restrictions if you ve already properly installed your DVI graphic controller in your OS 1 2 System Requirements for Setup Installation Important Please keep the installation procedure below Improper or no operation may result if the start up sequence is not correctly followed Step 1 Carefully unpack the contents of the shipping group Step 2 Plug and fasten the 5V power adapters to the 5V DC jack on the rear side of converter Ensure the Power LED ON Blue Step 3 Please check if the maximum resolution of the display is WUXGA 1920x1200 Otherwise follow the instructions for Self EDID Programming Procedure on page 1 5 Step 4 Connect the DVI source to DVI IN port over DVI cable If the DVI source is active status LED Blue will be turned on Step 5 Connect the OPTICAL OUT to 1 fibe DVI receiver DVFX 100 R over multi mode SC SC optical fiber Step 6 Plug DVFX
3. Fax 82 31 719 8032 www opticis com For order support please contact your Distributor or Reseller For technical support check with the Opticis web site www opticis com or contact techsupp opticis com
4. Then status LED Blue will blink 3 times and turned ON Step 4 Connect the DVI OUT port on the front side of converter to the DVI input port of display over DVI cable Then the status LED will begin to blink rapidly It indicates reading the EDID from the display and storing it in the EEPROM After 8 10 sec blinking the status LED will be turned OFF and it indicates completion of all procedure Step 5 Disconnect the converter from the display 1 5 Self EDID Programming Procedure Troubleshooting The display shows only black screen Ensure that all plugs and jacks used by external power supplies both Opticis and others are firmly connected Ensure that the Power and status LED ON Ensure that the video ports are firmly plugged in to the PC and display Ensure that the converter and receiver modules plugged correctly to the PC and display respectively Check if the PC and display are powered on and properly booted Screen is distorted or displays noises Check if the graphic resolution is properly set Go to the display properties of Windows and tap the settings Ensure that the resolution sets less than WUXGA 1920x1200 at 60Hz refresh ratio Reset the system Disconnect and reconnect the optical fiber or 5V power adapters Maintenance No special maintenance is required for the converter and power adapters Ensure that the converter and power adapters are stored or used in a benign environment fr
5. cifications Warranty Information 1 One Year Warranty Opticis warrants this DVDF 200 to be free from defects in workmanship and materials under normal use and service for a period of one 1 year from the date of purchase from Opticis or its authorized resellers If a product does not work as warranted during the applicable warranty period Opticis shall at its option and expense repair the defective product or part d eliver to customer an equivalent product or part to replace the defective item or refund to customer the purchase price paid for the defective product All products that are replaced will become the property of Opticis Replacement products may be new or reconditioned Any replaced or repaired product or part has a ninety 90 day warranty or the reminder of the initial warranty period whichever is longer Opticis shall not be responsible for any software firmware information or me mory data of customer contained in stored on or integrated with any product s returned to Opticis for repair under warranty or not Warranty Limitation and Exclusion Opticis shall have no further obligation under the foregoing limited warranty if the product has been damaged due to abuse misuse neglect accident unusual physical or electrical stress unauthorized modifications tampering alterations or service other than by Opticis or its authorized agents causes other than from ordinary use or failure to properly use the produ
6. ct in the application for which said product is intended Dispose of Old Electrical amp Electronic Equipment Applicable in the European Union and other European countries with separate systems This symbol on the product or on its packaging indicates that this product shall not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative z consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product The recycling of materials will help to conserve natural resources For more detailed information about recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product 1 8 Warranty Information Regulatory Statements This device complies with part 15 of FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 and 2 of FCC Rules EN 55022 55024 61000 3 for CE certification These limits are designed to provide reasonab
7. ee from liquid or dirt contamination There are no user serviceable parts Refer all service and repair issues to Opticis Technical Support and Service For commercial or general product support contact your reseller For technical service contact Opticis by email techsupp opticis com or visit its website at www opticis com 1 6 Troubleshooting Maintenance Technical Support Product Specifications DVDF 200 DVI to 1 fiber DVI converter O Compliance with DVI standard Supports DVI1 0 fully implemented by fiber optic communication and DDC2B by virtual DDC O Extension limit 500 meters 1640 feet for WUXGA 1920x1200 60Hz refresh rate O Graphic transmission bandwidth Supports up to WUXGA 60Hz or 1 65Gbps bandwidth per graphic channel O Supporting resolution Based on DVI input HDTV 480p 720p 1080p VESA VGA SVGA XGA WXGA SXGA WXGA UXGA WSXGA WUXGA O Fiber optic connection DVDF 200 has one 1 SC receptacles so as to be connected with one 1 SC multi mode fiber having 62 5 50 125um core DDC connection Virtual DDC by Self EDID programming Dimensions WDH 104 x 112 x 28mm O Environmental Specifications E Operating temperature 0 C to 50 C Storage temperature 30 C to 70 C m Humidity 0 to 85 AC DC Power Adapter O Power Input AC 100 240V 50 60Hz 0 1A O Power Output 5 V 3A SMPS DC power Adapter O Cord DC Jack Core is 5 V and outer is GND 1 7 Product Spe
8. le protection against harmful interference when the equipment is operated in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction guide may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Re orient or relocate the receiving antenna e Increase the separation between the equipment and the receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult a service representative for help Properly shielded and grounded cables and connectors must be used in order to comply with FCC CE emission limits Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment 1 9 Regulatory Statements 2013 Opticis Co Ltd All Rights Reserved Revision 1 1 3 Sep 2013 Opticis Locations Headquarters Opticis Co Ltd 16Fl Kins Tower 8 Sungnam daero 331 beon gil Bundang gu Seongnam si Gyunggi do 463 844 South Korea Te 82 31 719 8033
9. pTIcis www opticis com DVI to 1 fiber DVI converter DVDF 200 User s Manual Doc No OC D130903 Rev1 1 Manual Contents Manual Contents Welcome Product Description System Requirements for Setup Installation Self EDID Programming Procedure Troubleshooting Maintenance Technical Support Product Specifications Warranty Information Regulatory Statements Pictorials Figure 1 Connection Diagram of DVDF 200 1 0 Manual Contents Welcome Congratulations on your purchase of the DVI to 1 fiber DVI converter DVDF 200 This manual contains information that will assist you in installing and operating the product Product Description The DVDF 200 DVI to 1 fiber DVI converter receives DVI up to WUXGA 1920x1200 60Hz signal and converts to optical signal and transmits up to transmits 500 meters 1640feet over one 1 SC multi mode fibers OPTICIS 1 fiber DVI receiver DVFX 100 R is used as a pair to recover 1 fiber DVI to electrical DVI The EDID Extended Display Identification Data in a display can be read and restored by just connecting once transmitter to the display This Self EDID programming feature makes the installation of DVDF 200 more easy and flexile at any variable resolution display systems For your convenience WUXGA EDID had been stored before shipment as a default Shipping Group Oo DVDF 200 DVI to 1 fiber DVI converter One 1 unit O AC DC power adapter One 1 unit of 5V 3
Download Pdf Manuals
Related Search