Home

User Manual

image

Contents

1. Do not clean the burners in the dish washer e Clean the appliance with a moist soft cloth Only use neutral detergents Do not use abrasive products abrasive cleaning pads solvents or metal ob jects 2 4 Disposal WARNING Risk of injury or suffocation 3 PRODUCT DESCRIPTION 3 1 Cooking surface layout e Contact your municipal authority for in formation on how to discard the appli ance correctly e Disconnect the appliance from the mains supply e Cut off the mains cable and discard it e Flat the external gas pipes Q Semi rapid burner Triple Crown burner Auxiliary burner Control knobs 3 2 Control knobs x A 4 DAILY USE WARNING Description no gas supply off position ignition position maximum gas supply Refer to the Safety chapters Symbol Description minimum gas Supply 4 1 Ignition of the burner A WARNING Be very careful when you use open fire in kitchen environment Manufacturer decline any respon sibility in case misuse of the flame Always light the burner before you put cookware To light the burner 1 i Turn the control knob counterclock wise to the maximum position XX and push it down Keep the control knob pushed for ap proximately 5 seconds this will let thermocouple to warm up If not the gas supply will be interrupted Adj
2. sheath 1 To replace the connection cable use only HO5V2V2 F T90 or equivalent type Make sure that the cable section is applicable to the voltage load and the working temperature The yellow green earth wire B must be approxi mately 2 cm longer than the live and neutral wire A N WARNING A cut off plug inserted into a 13 amp socket is a serious safety shock hazard Ensure that the cut off plug is disposed of safely N The replacement of electric cable must be carried out exclusively by the service force centre or by per sonnel with similar competencies in accordance with the current regulations 8 6 Building In min 600 mm min 100 mm min 650 mm 14 wwweelectrolux com A supplied seal B supplied brackets CAUTION Install the appliance only on a worktop with flat surface 8 7 Possibilities for insertion Kitchen unit with door The panel installed below the hob must be easy to remove and let an easy access 9 TECHNICAL INFORMATION Hob dimensions Width Length 594 mm 510 mm Hob recess dimensions Width 560 mm Length 480 mm in case a technical assistance intervention is necessary kain 20 mm max 150 mm A Removable panel B Space for connections Kitchen unit with oven The hob recess dimensions must obey the indication and the kitchen unit must be equippe
3. ata are necessary to help you quickly and correctly These data are available on the supplied rating plate Model description e Product number Serial Number S N Use the original spare parts only They are available at Service Force Centre and ap proved spare parts shops 7 1 Labels supplied with the accessories bag Stick the adhesive labels as indicated be low si MOD TYPE PROD NO PROD NO Ew er ne SER NO SER NO a DATA DATA MADE IN ITALY MODEL MODEL u X X Stick it on Guarantee Card and send this part Stick it on Guarantee Card and keep this part 8 INSTALLATION WARNING Refer to the Safety chapters A WARNING The following instructions about installation connection and main tenance must be carried out by qualified personnel in compliance with standards and local regula tions in force 8 1 Important safety requirements This hob must be installed in accordance with the Gas Safety Installation and Use Regulations Current Edition and the IEE Wiring Regulations Current Edition Stick it on instruction booklet For appliances installed in the Republic of Ireland please refer to NSAI Domestic Gas Installation 1 5 813 Current Editions and the ETCI Rules for Electrical Installa tions Provision for ventilation Detailed recomm
4. d with vents to let a continu ous supply of air The electrical connec tion of the hob and the oven must be in stalled separately for safety reasons and to let easy remove oven from the unit 120 cm2 180 cm2 Heat input Triple Crown 4 0 kW burner Semi rapid burn 2 0 kW er Auxiliary burner 1 0 kW ENGLISH 15 TOTAL POWER G20 2H 20 mbar Category 2 9 kW F G30 3 28 30 Gas supply G20 2H 20 mbar mbar 654 g h Appliance class 3 G31 3 37 mbar 643 g h By pass diameters Electric supply 230 V 50 Hz Burner By pass in 3 core flexible ca 1 100 mm ble with non re Auxili 28 wireable plug fit ted with a 3 amp Semi rapid 32 cartridge fuse Triple Crown 56 Gas connection R 1 2 Gas burners RE NORMAL POWER NOR MAL DUCED NATURALGAS LPG Butane Propane Burn POWER POW G20 2H 20 G30 G31 3 28 30 37 ER ER mbar mbar inj inj G30 G31 kW kW 1 100 ms h 1 100 mm mm g h g h Auxiliary 1 0 0 33 70 0 095 50 T3 71 Semi rapid 2 0 0 45 96 0 190 ral 145 143 Triple Grown 4 0 1 4 146 0 381 98 291 286 10 ENVIRONMENT CONCERNS Recycle the materials with the symbol Put the packaging in applicable containers to recycle it Help protect the environment and human health and to recycle waste of electrical and electronic appliances Do not dispose appliances marked with the symbol with the household waste Return the product to your
5. e appliance and the up per drawer is sufficient for air circula tion The bottom of the appliance can get hot We recommend to install a non combustile separation panel under the appliance to prevent access to the bot tom Electrical connection WARNING Risk of fire and electrical shock All electrical connections must be made by a qualified electrician The appliance must be earthed Before carrying out any operation make sure that the appliance is disconnected from the power supply e Use the correct electricity mains cable e Do not let the electricity mains cable tangle e Make sure the mains cable or plug if applicable does not touch the hot ap pliance or hot cookware when you connect the appliance to the near sock ets e Make sure the appliance is installed correctly Loose and incorrect electricity mains cable or plug if applicable can make the terminal become too hot e Make sure that a shock protection is in stalled e Use the strain relief clamp on cable e Make sure not to cause damage to the mains plug if applicable or to the mains cable Contact the Service or an electrician to change a damaged mains cable e The electrical installation must have an isolation device which lets you discon nect the appliance from the mains at all poles The isolation device must have a contact opening width of minimum 3 mm Use only correct isolation devices line protecting cu
6. e by pass screw in e If you change from liquid gas to natural gas G20 20 mbar undo the by pass screw approximately 1 4 of a turn 1 2 of a turn for Triple Crown burner A WARNING Make sure the flame does not go out when you quickly turn the knob from the maximum position to the minimum position 8 5 Electrical connection Do not pull the mains cable to discon nect the appliance Always pull the mains plug e The appliance must not be connected with an extension cable an adapter or a multiple socket There is a risk of fire Do not let the power cable to heat up to a temperature of more than 90 C The cable should be guided by means of clamps fixed to the side of the cabi net in order to avoid any contact with the equipment beneath the cooktop e Make sure that there is access to the mains plug after the installation Electrical Requirements Permanent electrical installation must agree with the latest E E Regulations and local Electricity Board regulations For your own safety the installation must be done by a qualified electrician e g your local Electricity Board or a contractor Who is on the roll of the National Inspec tion Council for Electrical Installation Con tracting NICEIC 1 The manufacturer refuses to be held responsible if these safety measures are not abi ded by Supply connections This hob has to be connected to 230 240 V 50 Hz electricity supply T
7. ee ere 2 Electrolux EGG6343 EN HOB USER MANUAL 2 wwweelectrolux com CONTENTS J SAFETY INFORMATION u s tet tee cee ean aia eee Soke Sabb aba kasu 3 2 SAFELY INSTRUCTIONS daa Papa Linie 4 3 PRODUCT DESCRIPTION L yy sassa aps a whee me eR RAYE RE RR Ee ey 6 DALY USE deeb DD nu ot RME aoa na edad ie S 6 5 HELPFUL HIINTS AND TIPS alan dates aa Gade ead oe ed eka Pa 7 6 GARE AND CLEANING 28 oka ede eee Ra 8 Te TROUBLESHOOTING 34 gs bee bbe ee d di 9 8 INSTALLATION Dane ventes Cube toner 10 9 TECHNICALINFORMATION eRe Encens 14 WE RE THINKING OF YOU Thank you for purchasing an Electrolux appliance You ve chosen a product that brings with it decades of professional experience and innovation Ingenious and stylish it has been designed with you in mind So whenever you use it you can be safe in the knowledge that you ll get great results every time Welcome to Electrolux Visit our website for 9 Get usage advice brochures trouble shooter service information www electrolux com 2 Register your product for better service EY www electrolux com productregistration Buy Accessories Consumables and Original spare parts for your appliance w www electrolux com shop CUSTOMER CARE AND SERVICE We recommend the use of original spare parts W
8. endations are contained in the following British Standards Codes Of Practice B S 6172 B S 5440 Par 2 and B S 6891 Current Editions The hob should not be installed in a bed sitting room with a volume of less than 20 m If it is installed in a room of volume less than 5 ms an air vent of effective area of 100 cm is required If it is installed in a room of volume between 5 ms and 10 ms an air vent of effective area of 50 cm is required while if the volume exceeds 11 no air vent is required However if the room has a door which opens directly to the outside no air vent is required even if the volume is between 5 ms and 11 m8 If there are other fuel burning appliances in the same room B S 5440 Part 2 Cur rent Edition should be consulted to deter mine the requisite air vent requirements For appliances installed in the Republic of Ireland please refer to the NSAI Domestic Gas Installation 1 5 813 Current Editions Table Four Location The hob may be located in a kitchen a kitchen diner or bed sitting room with a volume greater than 20 ms but not in a bathroom or shower room The minimum distance combustible mate rial can be fitted above the hob in line with the edges of the hob is 400 mm If it is fit ted below 400 mm a space of 50 mm must be allowed from the edges of the hob For appliances installed in the Republic of Ireland please refer to NSAI Domestic Gas Installation 1 5 813 Current Ed
9. h flammable products in near or on the appliance WARNING Risk of damage to the appliance Do not keep hot cookware on the con trol panel Do not let cookware to boil dry Do not activate the cooking zones with empty cookware or without cookware e Be careful not to let objects or cook ware fall on the appliance The surface can be damaged Do not put aluminium foil on the appli ance Do not let acid liquids for example vin egar lemon juice or limescale remover touch the hob This can cause matt patches e Provide good ventilation in the room where the appliance is installed e Make sure that the ventilation openings are not blocked e Use only stable cookware with the cor rect shape and diameter larger than the dimensions of the burners There is a risk of overheating and rupture of the glass plate if applicable e Make sure the flame does not go out when you quickly turn the knob from the maximum to the minimum position e Make sure pots are centrally positioned on the rings and do not stick out over edges of the cooking surface e Use only the accessories supplied with the appliance Do not install a flame diffuser on the burner 2 3 Care and Cleaning WARNING Risk of damage to the appliance Clean regularly the appliance to prevent the deterioration of the surface material Do not use water spray and steam to clean the appliance 6 www electrolux com
10. he hob has a terminal block which is marked as follows e L Live terminal N Neutral terminal e or E Earth terminal Before carrying out the connection make sure 1 The limiter valve and the electrical system can take the appliance load see the rating plate 2 The supply system is equipped with an efficient earth connection in com pliance with the current standards and regulations 3 The outlet or omnipolar switch used for connection is easily accessible with the appliance installed The appliance is supplied with a 3 core flexible powercable with a 3 amp plug If it is necessary to change the fuse use a 3 amp ASTA approved BS 1362 fuse ENGLISH 13 A Green and Yellow B 3 amp fuse C Brown D Cord clamp E Blue The wires in the cord are coloured as fol lows Green and yellow Earth Blue Neutral Brown Live Replacement of the connection cable 1 Connect the green and yellow earth wire to the terminal which is marked With the letter or the earth symbol Or coloured green and yellow 2 Connect the blue neutral wire to the terminal which is marked with the let ter or coloured blue 3 Connect the brown live wire to the terminal which is marked with the let ter L It must always be connected to the network phase There must be no cut or stray strands of wire present The cord clamp must be correctly attached to the outer
11. hen contacting Service ensure that you have the following data available The information can be found on the rating plate Model PNC Serial Number A Warning Caution Safety information i General information and tips 4 Environmental information Subject to change without notice ENGLISH 3 1 SAFETY INFORMATION Before the installation and use of the appliance carefully read the supplied instructions The manufacturer is not responsible if an incorrect installation and use causes in juries and damages Always keep the instructions with the appliance for future reference 1 1 Children and vulnerable people safety WARNING Risk of suffocation injury or permanent disability This appliance can be used by children aged from 8 years and above and persons with reduced physical sensory or mental capabilities or lack of experience and knowledge if they are supervised by an adult or a per son Who is responsible for their safety Do not let children play with the appliance Keep all packaging away from children Keep children and pets away from the appliance when it operates or when it cools down Accessible parts are hot If the appliance has a child safety device we recom mend that you activate it Cleaning and user maintenance shall not be made by children without supervision 1 2 General Safety The appliance and its accessible parts become hot during use Do not touch the heating elements Do not opera
12. iameters applicable to the size of burners Burner Diameters of cook ware Triple 180 260 mm Crown Front Semi 120 180 mm rapid Rear Semi 120 220 mm rapid Auxiliary 80 160 mm WARNING Make sure that the bottoms of pots do not stand above the con trol knobs If the control knobs are under the bottoms of pots the flame heats them up Do not put the same pan on two burners A 6 CARE AND CLEANING WARNING Refer to the Safety chapters AS A WARNING Deactivate the appliance and let it cool down before you clean it Disconnect the appliance from the electrical supply before you do cleaning or maintenance work Scratches or dark stains on the surface have no effect on how the appliance operates i e You can remove the pan supports to easily clean the hob e To clean the enamelled parts cap and crown wash them with warm soapy water and dry them carefully before you put them back e Wash stainless steel parts with water and then dry them with a soft cloth e The pan supports are not dishwasher proof They must be washed by hand e When you wash the pan supports by hand take care when you dry them as WARNING Make sure that pot handles is not above the front edge of the cook top Make sure that pots are cen trally put on the rings in order to get maximum stability and to get lower gas consumption Do not put unstable or damaged pots on the rings to prevent from
13. ition Section 7 Permitted Locations of Appli ance 8 2 Gas Connection WARNING Any gas installation must be car ried out by a GAS SAFE REGIS TER installer Make sure that once the hob is installed it is easily accessible for the engineer in the event of a breakdown The manufacturer will not accept liability should the above instructions or any of the other safety instructions incorporated in this instruction booklet be ignored On the end of the shaft which includes the G 1 2 threaded elbow adjustment is fixed so that the washer is fitted between the components as shown in the diagram Screw the parts together without using excessive force ENGLISH 11 gt lt C A End of shaft with nut B Washer Elbow Connection to the gas supply should be With either rigid or semi rigid pipe i e steel or copper The connection should be suitable for connecting to R 1 2 1 2 BSP male thread When the final connection has been made it is essential that a thorough leak test is carried out on the hob and installa tion Make sure that the main connection pipe does not exert any strain on the hob If you use flexible metal pipes make sure that they agree to ISO 10380 and ISO 10807 standards Be careful they do not come in touch with mobile parts or they are not squeezed Also be careful when the hob is put together with an oven A It is important to i
14. lighting and check that the burner crown holes are not obstructed 6 2 Periodic maintenance Periodically speak your local Service Force Centre to check the conditions of the gas supply pipe and the pressure ad juster if fitted Remedy There is no spark when lighting the gas supply e There is no electrical e Make sure that the unit is connected and the electrical supply is switched on e Control the fuse If the fuse is released more than one time refer to a qualified electrician e Burner and crown Make sure that the are placed uneven The flame is blow out im mediately after ignition The gas ring burns un evenly dues burner cap and crown are in correct positions e Thermocouple is not e After lightning the heated sufficient flame keep the knob pushed for approxi mately 5 seconds e Burner crown is e Make sure that the in blocked with food resi jector is not blocked and the burner crown is clear of food parti cles If there is a fault first try to find a solution to the problem yourself If you cannot find a solution to the problem yourself speak your dealer or the local Service Force Centre 1 If you operated the appliance in correctly or the installation was not carried out by a registered en gineer the visit from the customer service technician or dealer may not take place free of charge even during the warranty period 10 www electrolux com These d
15. local recycling facility or contact your municipal office www electrolux com shop 356989702 A 452012 fan
16. nstall the elbow correctly with the shoulder on the end of the thread fitted to the hob connecting pipe Failure to ensure the correct as sembly will cause leakage of gas A A Rigid connection Make sure that the gas supply pressure of the appliance obeys the recommended values Carry out connection by using metal rigid pipes copper with mechanical end 8 3 Injectors replacement 1 Remove the pan supports 2 Remove the caps and crowns of the burner 3 With a socket spanner 7 remove the injectors and replace them with the ones which are necessary for the type 12 www electrolux com of gas you use see table in Techni cal Information chapter 4 Assemble the parts follow the same procedure backwards 5 Replace the rating plate it is near the gas supply pipe with the one for the new type of gas supply You can find this plate in the package supplied with the appliance If the supply gas pressure is changeable or different from the necessary pressure you must fit an applicable pressure ad juster on the gas supply pipe 8 4 Adjustment of minimum level To adjust the minimum level of the burn ers 1 Light the burner 2 the knob on the minimum posi tion 3 Remove the knob 4 With a thin screwdriver adjust the by pass screw position A SS A The by pass screw e If you change from natural gas G20 20 mbar to liquid gas fully tighten th
17. spill and injury WARNING Do not use a flame diffuser the enamelling process occasionally leaves rough edges If necessary re move stubborn stains using a paste cleaner e Make sure you position the pan sup ports correctly after cleaning To make the burners work correctly make sure that the arms of the pan supports are in the centre of the burner Q Be very careful when you replace the pan supports to prevent the hob top from damage After cleaning dry the appliance with a soft cloth Removing the dirt 1 Remove immediately melting plastic plastic foil and food con taining sugar Stop the appliance and let it cool down before you clean lime scale rings water rings fat stains shiny metallic discolorations Use a special cleaner applicable for sur face of hob 2 Clean the appliance with a damp cloth and some detergent 3 At the end rub the appliance dry with a clean cloth The stainless steel can become tarnished if it is too much heated Refer to this you must not cook with potstones earthen ware pans or cast iron plates 7 TROUBLESHOOTING Problem Possible cause ENGLISH 9 6 1 Cleaning of the spark plug This feature is obtained through a ceramic ignition candle with a metal electrode Keep these components well clean to prevent difficult
18. t outs fuses screw type fuses removed from the holder earth leakage trips and contactors Gas connection e Al gas connections should be made by a qualified person e Make sure that there is air circulation around the appliance e The information about the gas supply is on the rating plate This appliance is not connected to a device which evacuates the products of combustion Make sure to connect the appliance according to current in stallation regulations Pay attention to requirements regarding adequate venti lation 2 2 Use WARNING Risk of injury burns or electric shock Use this appliance in a household envi ronment Do not change the specification of this appliance Do not let the appliance stay unatten ded during operation Do not operate the appliance with wet hands or when it has contact with wa ter Do not put cutlery or saucepan lids on the cooking zones They become hot Set the cooking zone to off after use WARNING Risk of fire or explosion e Fats and oil when heated can release flammable vapours Keep flames or heated objects away from fats and oils when you cook with them The vapours that very hot oil releases can cause spontaneous combustion ENGLISH 5 e Used oil that can contain food rem nants can cause fire at a lower temper ature than oil used for the first time Do not put flammable products or items that are wet wit
19. te the appliance by means of an external timer or Separate remote control system Unattended cooking on a hob with fat or oil can be dangerous and may result in fire 4 www electrolux com e Never try to extinguish a fire with water but switch off the appliance and then cover flame e g with a lid or a 2 fire blanket e Do not store items on the cooking surfaces e Do not use a steam cleaner to clean the appliance e Metallic objects such as knives forks spoons and lids should not be placed on the hob surface since they can get hot SAFETY INSTRUCTIONS This appliance is suitable for the following markets GB 2 1 Installation WARNING Only a qualified person must in stall this appliance Remove all the packaging Do not install or use a damaged appli ance Obey the installation instruction Sup plied with the appliance Keep the minimum distance from the other appliances and units Always be careful when you move the appliance because it is heavy Always wear safety gloves Seal the cut surfaces with a sealant to prevent moisture to cause swelling Protect the bottom of the appliance from steam and moisture Do not install the appliance adjacent to a door or under a window This pre vents hot cookware to fall from the ap pliance when the door or the window is opened If the appliance is installed above draw ers make sure that the space between the bottom of th
20. ust the flame after it is regular not light check if the crown and its cap are in correct positions If after some tries the burner does A B Burner Burner crown gnition candle D Thermocouple 5 HELPFUL HINTS AND TIPS WARNING Refer to the Safety chapters 1 ENGLISH 7 WARNING Do not keep the control knob pushed for more than 15 sec onds If the burner does not light after 15 seconds release the control knob turn it into off position and try to light the burner again after minimum 1 minute In the absence of electricity you can ignite the burner without elec trical device in this case approach the burner with a flame push the relevant knob down and turn it counter clockwise to maximum gas release position If the burner accidentally goes out turn the control knob to the off position and try to light the burner again after minimum 1 minute The spark generator can start au tomatically when you switch on the mains after installation or a power cut It is normal 4 2 Turning the burner off To put the flame out turn the knob to the symbol A WARNING Always turn the flame down or switch it off before you remove the pans from the burner 5 1 Energy savings f possible always put the lids on the pans www electrolux com e When the liquid starts to boil turn down the flame to barely simmer the liquid Use cookware with d

Download Pdf Manuals

image

Related Search

Related Contents

  当日の問題  e+p VB 20  3Com 3C16491 Switch User Manual  Installation, Operation, Maintenance  Texas Instruments MSP50C614 User's Manual  

Copyright © All rights reserved.
Failed to retrieve file