Home
Configuration Manual - Epsio FX (Reveal Mode) 1.1
Contents
1. q Note A If you install a new graphic pack after you have configured Epsio FX Reveal Mode check that the new graphic pack has been selected in the Launcher before you use the Epsio FX Reveal Mode Setting up Epsio Configuring Epsio Parameters To configure the Epsio parameters proceed as follows On the Epsio server open the Epsio FX Reveal Mode user interface by clicking the Epsio FX Reveal Mode icon The Epsio FX Reveal Mode Launcher opens Y Advanced Click Advanced to expand the Advanced pane where you will find the Epsio FX Reveal Mode parameters Fill in the fields as explained in the Advanced pane and in the section Epsio FX Reveal Mode Parameters on page 9 When you have defined the parameters you can Start Epsio FX Reveal mode by clicking the Start or Start Offline Mode button at the top of the Launcher window Close the launcher if you do not want to use Epsio FX Reveal Mode directly 2 Configuration CONFIGURATION MANUAL 1 2 Epsio FX Reveal Mode 2 4 2 2 Configuration V5 Epsio FX Reveal Mode Parameters Introduction The parameters of Epsio FX Reveal Mode are available in the Advanced pane of the Epsio FX Reveal Mode launcher When you open the Advanced tab the parameter values are the ones of the last session See section Configuring Epsio Parameters on page 8 to see how to access the parameters Ac EpsioFx Reveal mod Advanced Video Fo
2. Genlock Other PGM in E E VIDEO SDI VITC Audio EVS Server Scoreboard LSM Remote VIDEO SDI VITC Audio Graphics Epsio 3U 1 Introduction 3 EVS Broadcast Equipment SA Issue 1 2 A July 2015 1 3 Requirements and Limitations Hardware and Software Requirements EVS Server Software Multicam version 11 02 or 12 02 or higher Epsio FX Hardware Epsio with the new version of the backplane including the following connectors above the power supplies one XLR connector e twoRS 232 Data Com ports Software OS Windows 7 Graphic Board NVIDIA QUADRO FX 2000 e XSecure license option 20 for Epsio FX Reveal Mode Timecode Requirements When Epsio is cabled a continuous reference timecode must be entered into Epsio During data recording this timecode allows Epsio to store the scoreboard data with a corresponding timecode See section Cabling on page 2 When Multicam is configured you need to make sure the PGM coming from the EVS server into Epsio through the video input 1 port IN 1 has the LTC timecode embedded in HAnc VITC timecode During replay this timecode allows Epsio to read the stored scoreboard data corresponding to the timecode of the incoming video signal See section Setting up Multicam on page 7 Limitations The following scoreboard data protocols are currently supported Daktronics and OES e There is a
3. Science Park 852 2914 2501 13 rue Bois St Jean B 4102 Seraing Other regional offices Belgium www evs com contact EVS Broadcast Equipment is continuously adapting and improving its products in accordance with the ever changing requirements of the Broadcast Industry The data contained herein is therefore subject to change without prior notice Companies and product names are trademarks or registered trademarks of their respective companies
4. need to select an archive name to be able to start working with Epsio FX Reveal Mode 11 EVS Broadcast Equipment SA Issue 1 2 A July 2015 2 4 3 2 4 4 Working Offline Introduction By default Epsio FX Reveal Mode works in Live mode It is operated during a match and the scoreboard data is fed directly form the scoreboard into Epsio In specific cases for example a demo you need to work outside a production environment In this case you will work as follows e The AV material recorded on an EVS video server is fed into Epsio e The scoreboard data stored in an archive is used on Epsio instead of a direct feed The Data Com port is therefore not cabled and the continuous reference timecode does not have to be fed into Epsio either How to Set up Epsio to Work Offline To set up Epsio to work offline you have to set the Epsio parameters as follows 1 Click the Epsio FX Reveal Mode icon on the desktop then click Advanced in the Launcher to open the Advanced pane In the Data group box Mode field select Offline In the Data group box Archive field select the archive you want to use to provide the scoreboard and corresponding TC data 4 Fill in the other parameters as described in Epsio FX Reveal Mode Parameters on page 9 5 Click the Start Offline Mode button in the Epsio Launcher Managing Scoreboard Data Introduction You may want to keep the scoreboard data after the match for example
5. to further exploit the AV material with a scoreboard data display after the event or to provide the data for a demo Tothis end you will need to store the scoreboard data to an archive may then need to export it and then import and restore it onto another Epsio server These actions are performed from the Launcher or via the EpsioRevealDataSetManager bat file opening a DOS command 2 Configuration pum V5 CONFIGURATION MANUAL 1 2 Epsio FX Reveal Mode em The following table gives an overview on the actions to manage scoreboard data and where they are performed Action Interface Archive the scoreboard data Epsio FX Reveal Mode Launcher Restore a scoreboard data archive Epsio FX Reveal Mode Launcher Export a scoreboard data archive EpsioRevealDataSetManager bat file Import a scoreboard data archive EpsioRevealDataS etManager bat file Delete a scoreboard data archive EpsioRevealDataSetManager bat file Rename a scoreboard data archive EpsioRevealDataSetManager bat file How to Archive the Scoreboard Data To archive the timestamped scoreboard data during a live production proceed as follows 1 Click the Epsio FX Reveal Mode icon on the desktop then click Advanced in the Launcher to open the Advanced pane 2 Inthe Data group box Archive field type the name you want to give to the archive The scoreboard data will be archived on the Epsio server during the production This archive will remain available afte
6. 2 5 1 Checking the Parameters Checking the Information Screen Introduction After Epsio FX Reveal Mode has been configured you start the recording process by clicking the Start or Start Offline Mode button in the Launcher At this time an information window is displayed on the output of Epsio server It allows the operator to check the Epsio configuration and the signal characteristics The Information window looks like the following one Epsio FX BLACKBURST LIVE 1 MAR 2015 HD 1080i 50 PAL 18 58 41 07 08 44 12 0 18 58 28 00 08 57 1 2 Epsio FX BLACKBURST 2 SEP 2015 HD 720p 60 NTSC 11 28 22 26 00 00 0 0 01 37 33 13 00 00 0 0 2 Configuration pm m V5 CONFIGURATION MANUAL 1 2 Epsio FX Reveal Mode sum 2 Configuration Background Colors This table describes that meaning of the possible background colors for the cells of the Information window Background Color Blue Gray Orange Red Field Values Meaning Command area The cell value is editable using the specified keyboard shortcut Cell with normal field value Cell with field value revealing a potential problem for ex license expiration This corresponds to a warning Cell with field value revealing a problem for ex wrong genlock signal This corresponds to an error The following table describes the information in each cell and explains the possible issues which lead to an orange or red cell
7. 6 frame delay between the EVS server output and the Epsio output The Data Com ports are configured so that FIFO buffers are not used This is a factory setting 1 Introduction pum V5 CONFIGURATION MANUAL 1 2 Epsio FX Reveal Mode mm 1 4 1 Introduction Opening Epsio FX Reveal Mode How to Open Epsio FX Reveal Mode To open Epsio FX Reveal Mode user interface proceed as follows on the Epsio server e Click the application icon OR e Select the application from the Start menu gt All Programs gt Evs Broadcast Equipment EpsioFX EpsioFX Reveal Mode Epsio FX Reveal Mode Launcher The Epsio FX Reveal Mode Launcher opens FX EpsioFx Reveal mode Y Advanced Epsio FX Reveal Mode consists in this Launcher window in which you can perform the following actions Defining the Epsio FX Reveal Mode parameters This is one of the required configuration steps before you can start working with Epsio FX Reveal Mode See section Configuring Epsio Parameters on page 8 Starting Epsio FX Reveal Mode once the application has been configured and tested on the venue See below How to Start Epsio FX Reveal Mode Before you can actually start using Epsio FX Reveal Mode you need to configure it as explained in the section Overview on page 6 When Epsio FX Reveal Mode has been configured and is open click the Start or Start Offline Mode button for the application to start
8. CONFIGURATION MANUAL Epsio FX Reveal Mode Version 1 2 July 2015 V5 Ei V5 CONFIGURATION MANUAL 1 2 Epsio FX Reveal Mode Sa Disclaimer This manual and the information contained herein are the sole property of EVS Broadcast Equipment SA and or its affiliates EVS and are provided as is without any expressed or implied warranties including but not limited to the implied warranties of merchantability and fitness for a particular purpose In particular EVS makes no warranty regarding the use or the consequences of use of this manual and the information contained herein Furthermore EVS may not be held liable for any direct or indirect incidental punitive or consequential loss damage cost or expense of any kind whatsoever and howsoever resulting from the normal or abnormal use of this manual and the information contained herein even if advised of the possibility of such loss damage cost or expense While every effort has been made to ensure that the information contained in this manual is accurate up to date and reliable EVS cannot be held liable for inaccuracies or errors that may appear in this publication The information in this manual is furnished for informational purpose and use only and subject to change without notice This manual cancels and replaces any previous versions thereof Copyright Copyright 2014 2015 EVS Broadcast Equipment SA All rights reserved This manual may not be reproduced tr
9. anscribed stored in a database or an retrieval system translated into any language computer language transmitted in any form or by any means electronically mechanically printed photocopied optically manually or otherwise in whole or in part without the prior written consent of EVS Trademarks All product and brand names are registered trademarks and trademarks of EVS or of their respective owners Improvement Requests Your comments will help us improve the quality of the user documentation Please send improvement requests or report any error or inaccuracy on this user manual by e mail to doc evs com Regional Contacts You will find the full list of addresses and phone numbers on the following webpage http www evs com contacts EVS Broadcast Equipment SA Issue 1 2 A July 2015 User Manuals on EVS Website The latest version of the user manual if any and other user manuals on EVS products can be found on the EVS download center on the following webpage http www evs com downloadcenter pem V5 CONFIGURATION MANUAL 1 2 Epsio FX Reveal Mode Sa Table of Contents Table of Contents TABLE OF CONTENTS 2 111 Li INTRODUCTION coita sense 1 1 1 Product Description 2220 00 2 2 c ccc ce ence ccc cecceccecceeeteeeeeeees 1 A 224 cca thet atte eee a ee eee 2 1 3 Requirements and Limitations 2 000222 nenn 4 1 4 Opening Ep
10. ay the AV material from the EVS server s PGM is entered into Epsio and then replayed with the scoreboard data in overlay EVS Broadcast Equipment SA 1 2 Cabling Recommended Cabling The following schema shows how the Epsio hardware needs to be cabled to configure and operate Epsio FX Reveal Mode e The scoreboard data is entered into one of the RS DATA Com port RS 232 port e TheLTC reference timecode is entered into the LTC IN port XLR port Issue 1 2 A July 2015 e The video SDI audio and the VITC data embedded in the video signal are entered into the video input 1 port IN1 of the PCX3 board BNC connector e The Genlock data is entered into the GLK port BNC connector VIDEO SDI VITC PGM1 Audio Genlock EVS Server LTC reference Scoreboard timecode LSM Remote VIDEO SDI VITC Audio Graphics Epsio 3U 1 Introduction VS CONFIGURATION MANUAL 1 2 Epsio FX RevealMode Ss Alternate Cabling In case you cannot enter the LTC reference timecode via the LTC IN connector you can use an alternate cabling You can provide the reference timecode information by entering a PGM output of the EVS server into the video input 2 connector IN2 of Epsio This PGM output needs to be in E to E and have the same Multicam configuration as the PGM1 plugged into the video input 1 connector IN VIDEO SDI VITC Audio
11. background Cell Field Name Ref Mode Licence Video TC Live Data Live TC Replay Data Replay Description Genlock type and status The status is indicated by the cell color If the cell is red it means the genlock signal is bad Mode in which Epsio FX Reveal Mode is used Live or Offline Number of days before the expiry date of the XSecure Epsio FX Reveal Mode license option The cell turns orange when the license code will expire in less than 15 days The cell turns red when the license code has expired Video format applied to the video output of Epsio If the cell is red it means that the video format entered into the video input 1 port IN 1 does not correspond to the video format defined in the Epsio FX Reveal Mode parameters Reference timecode value read in the timecode input on the LTC IN port or on the video input 2 port IN2 when the alternate cabling is used Scoreboard data at the live timecode LTC timecode value read on the video input 1 port IN1 receiving the feed from the EVS server Scoreboard data at the replay timecode 17 EVS Broadcast Equipment SA Issue 1 2 A July 2015 2 9 2 Commands The following commands are available from the Information window To Do the following action To hide or show the information Press CTRL I screen To adjust the horizontal phase Press CTRL Left Arrow Right Arrow To ajust the vertical phase Press CTRL Up Arro
12. e for ATC VITC parameter has to be set to LTC for PGM1 Timecode insertion settings Inputs Outputs HD OUT ATC LTC No Userbits ATC VITC Userbits SD OUT D VITC No Lines 19 21 Q Note A If you use the alternate cabling configure in the same way the player channel plugged into the video input 2 port IN2 of the Epsio server Starting an Appropriate Multicam Configuration After you have set up the timecode insertion settings start a Multicam configuration on your EVS server The 1080p and 4K formats are not supported 2 3 Installing a Custom Graphic Pack When your company has requested a customized graphic pack you will receive an executable including all components of the graphic pack To install the custom graphic pack proceed as follows 1 Copy the executable on the Epsio server 2 Double click the executable The first installer window opens 3 Click Install 2 Configuration 7 EVS Broadcast Equipment SA Issue 1 2 A July 2015 2 4 2 4 1 4 Answer by Yes or Notothe following message Do you want to remove all other templates Even if you remove all other templates the default template will always remain installed on the Epsio server 5 Onthelast window click Finish to exit the installer The graphic pack is installed on the Epsio server and is available in the configurations settings of the Launcher in Epsio FX Reveal Mode See section Epsio FX Reveal Mode Parameters on page 9
13. ed together a difference may occur between the scoreboard and the graphics displayed This is due to the fact the data coming from the clock provider may arrive between 2 frames of the video You may also see a visual difference between the basket clock and the arena s ribbon board clocks in some cases 2 Configuration 19 EVS Broadcast Equipment SA 2 6 20 Issue 1 2 A July 2015 Troubleshooting No Scoreboard Data on Output If you do not see any data on the scoreboard display on the output this issue might have Several causes listed below For each possible cause perform the corresponding check Cause Solution Cause Solution Cause Solution The scoreboard is not connected to the Epsio server Check that the scoreboard is physically connected to the RS Data Com 1 or RS Data Com 2 port The connection port specified in the Launcher Check that the port number specified in the Input field in the Launcher corresponds to the RS Data Com port number that is connected The protocol specified in the Launcher does not correspond to the protocol of the connected scoreboard device Check that the protocol specified in the Protocol field in the Launcher corresponds to the communication protocol of the Scoreboard device 2 Configuration Sa V E To learn more about EVS go to www evs com Corporate 32 4 361 7000 North amp Latin America 1 973 575 7811 EVS Headquarters Asia amp Pacific Liege
14. her custom graphic packs are listed if they have been installed on the Epsio server 2 Configuration CONFIGURATION MANUAL 1 2 Epsio FX Reveal Mode Data Mode Description Values Initial value Intput Description Values Protocol Description Values Archive Description Values 2 Configuration V5 Working mode of Epsio FX Reveal Mode Depending on the working mode the Start button in the launcher will have a different wording Start or Start Offline Mode Two modes are available Live mode used by default when you work on a live production o The application reads the scoreboard data feed from the Com Port o The scoreboard data is recorded on Epsio e Offline mode used when you need to work outside the live production or perform a demo o The application reads the scoreboard data from an archive file selected by the user o No data is recorded on Epsio Live RS232 Data Com port on which the scoreboard data is entered 1forRS Com 1 e 2forRSCom2 Provider of the scoreboard whose data is entered into Epsio Two scoreboard protocols are available in Epsio Basketball Daktronics Basketball OES Name of the archive in which the recorded data is stored in live mode or read in offline mode In Live mode the scoreboard data is stored by default in an archive named by the following pattern Record YYYY MM DD You can specify another name In Offline mode you
15. o FX Reveal Mode Sa How to Adjust the Delay Without Control of the Scoreboard To adjust the delay when you cannot control the scoreboard proceed as follows 1 Record a video sequence where the shot clock reaches 0 0 and you see the red square around the basket lighting up 2 Jog back to this instant and adjust the delay with CTRL Page Up Page Down to get the shot clock 0 0 on the video output at the exact frame where the square around the arena scoreboard turns red 3 Check that the delay is good on all other cameras otherwise adjust it Restrictions Synchronized Cameras As Epsio FX Reveal Mode is based on the VITC synchronization it is important to check the signal timing Examples of camera sources not in sync Frame Sync If a camera is resynchronized through a frame synchronizer Supermotion combined output If the combined output of a camera operating as SuperMotion is recorded on another EVS server it will be delayed by a frame compared to the super motion phases iMovix x10 UltraMotion A processed camera like an iMovix 6x or 10x camera for UltraMotion has a slight delay Straight Recorded Clips Epsio FX Reveal Mode works with SLSM cameras However if the user records hypermotion cameras the VITC is not the same as with other cameras For this reason clips not created on the current record trains cannot be used with Epsio Fx Reveal Mode LED Timing Issue As the LED scoreboards are not genlock
16. r the production How to Export a Scoreboard Archive To export a scoreboard data archive out of the Epsio server proceed as follows 1 Select EpsioFX Reveal Mode Dataset Manager from the menu Start gt All Programs EVS Broadcast Equipment EpsioFx Reveal Mode A DOS prompt opens and displays a list of available commands on scoreboard archives Epsio Reveal Data set management Export Dataset Import Dataset Delete Dataset Rename Dataset Exit your choice 123 45 2 Configuration 13 EVS Broadcast Equipment SA Issue 1 2 A July 2015 2 Type 1 and press Enter The archives stored on the Epsio server are listed in the DOS prompt 3 Type the figure that corresponds to the archive you want to export and press Enter A Save As window opens 4 Pointto the requested location and type the name of the zip file where the scoreboard archive will be stored The scoreboard data archive is exported to a zip file stored in the specified path How to Import a Scoreboard Archive To import a scoreboard data archive to Epsio proceed as follows 1 Storelocally the zip file containing the scoreboard data archive to be imported onto the Epsio server 2 Select EpsioFX Reveal Mode Dataset Manager from the menu Start gt All Programs EVS Broadcast Equipment EpsioFx Reveal Mode A DOS prompt opens and displays a list of available commands on scoreboard archives 3 Type2and pres
17. rmat Timecode Input Graphics Template Data Mode Input Protocol Archive HD 720p 60 NTSC LTC Recommended BasketballGenerici Live Offline Com Port 1 Basketball Daktronics Record 2014 10 23 EVS Broadcast Equipment SA Issue 1 2 A July 2015 Video amp Reference Format Description Values Video standard field rate and resolution applied to the video output of Epsio The video standard defined on Epsio must correspond to the running configuration on the EVS server The list of values correspond to the formats available with the PCX3 board of Epsio SD 50PAL 16 9 SD60NTSC 16 9 HD 1080i 50 PAL HD 1080i 60 NTSC e HD 720p 50 PAL e HD 720p 60 NTSC Timecode Reference Input Description Values Initial value Graphics Template Description Values Live timecode reference used in the data recording to map the scoreboard data with a corresponding timecode Two values are possible depending on the cabling LTC if the continuous timecode reference is entered through the LTC IN port on the back panel VITC if the continuous timecode reference is entered through the video input 2 port IN 2 on the back panel In this case the incoming feed must be the HAnc VITC of a PGM in E E LTC Graphic pack to be used during the production At least the default graphic pack is installed and available It has the following name BasketballGeneric Ot
18. s Enter An Open window opens 4 Pointto the zip file containing the scoreboard data archive to import and press Open In the DOS prompt the following message is displayed Enter the name of the new DataSet 5 Type the name of the new data in the DOS promp and press Enter The scoreboard data archive is imported onto Epsio and will be available in the Launcher Data section and Archive field to be restored How to Restore the Scoreboard Data Archive If you want to restore a scoreboard data archive on an Epsio server where the original data has not been recorded you first need to import the scoreboard data archive onto the Epsio Server To restore a scoreboard data archive in an offline environment proceed as follows 1 Click the Epsio FX Reveal Mode icon on the desktop then click Advanced in the Launcher to open the Advanced pane 2 Inthe Data group box Archive field select the name of your archive from the drop down field The scoreboard data set included in the archive file is restored on the Epsio server and can be used in an offline environment 14 2 Configuration Ei V5 CONFIGURATION MANUAL 1 2 Epsio FX Reveal Mode Sa How to Rename a Scoreboard Archive To rename a scoreboard data archive on an Epsio server proceed as follows 1 Select EpsioFX Reveal Mode Dataset Manager from the menu Start gt All Programs gt EVS Broadcast Equipment gt EpsioFx Reveal Mode A DOS prompt open
19. s and displays a list of available commands on scoreboard archives Type 4 and press Enter The archives stored on the Epsio server are listed in the DOS prompt Type the figure that corresponds to the archive you want to rename and press Enter Type the new name for the scoreboard data archive and press Enter Answer Y and press Enter to confirm you want to rename the scoreboard data archive The scoreboard data archive is renamed and available with its new name in the Launcher If it was previously selected in the Launcher the renamed archive will still be selected in the Launcher the next time you will open Epsio FX Reveal Mode How to Delete the Scoreboard Archive To delete a scoreboard data archive on an Epsio server proceed as follows 1 3 4 Select EpsioFX Reveal Mode Dataset Manager from the menu Start gt All Programs gt EVS Broadcast Equipment gt EpsioFx Reveal Mode A DOS prompt opens and displays a list of available commands on scoreboard archives Type 3 and press Enter The archives stored on the Epsio server are listed in the DOS prompt Type the figure that corresponds to the archive you want to delete and press Enter Type Y and press Enter to confirm you want to delete the scoreboard data archive The scoreboard data archive is deleted on the Epsio server and is no longer available in the Launcher 2 Configuration 15 EVS Broadcast Equipment SA Issue 1 2 A July 2015 2 3
20. sio FX Reveal Mode 2 2 22 eee 5 2 CONFIGURATION 22 2 2222 6 ANOTHER PI 6 2 2 Setting up Multicam ssssssssssssssssssssssssss sss RR s essere lin 7 2 3 Installing a Custom Graphic Pack suuuuuuuueueeseseseess ese eese 7 2 4 Setting up EpSIO esee ceste ann reed nen een ea ne 8 2 4 1 Configuring Epsio Parameters oocccccccccccccccccccccccccccccccccccccnoo 8 2 4 2 Epsio FX Reveal Mode Parameters ssseeeessss 9 2 4 3 Working OMNE sesser rererere ei rear 12 2 4 4 Managing Scoreboard Data 222ccccceeneeeeeeeneeennnn 12 2 5 Checking the Parameters 00 00000 0c eee cece cece cece cece eeeeeeeeeeees 16 2 5 1 Checking the Information Screen _ 2 2 0 eee eececccececccccccceeeeecees 16 2 5 2 Adjusting the Delay 1 2000 0 2 s n eee RR rese 18 2 6 Troubleshooting No Scoreboard Data on Output 22 c cnneen 20 Ee V5 CONFIGURATION MANUAL 1 2 Epsio FX Reveal Mode Sa 1 1 1 1 Introduction Introduction Product Description Epsio FX can be used in Reveal Mode to display the scoreboard data of a basket ball match game clock and shot clock on the video output being replayed Epsio FX Reveal Mode is based on the following working principle During the match the scoreboard data is stored on the Epsio server along with a synchronized reference timecode During repl
21. w Down Arrow To reset the phases Press CTRL R To increase or reduce the delay Press CTRL Page Up Page Down See section Adjusting the Delay on page 18 for more information on this task Adjusting the Delay Introduction Before you start working live on a venue with Epsio FX Reveal Mode you need to adjust the delay to compensate for the offset between the recorded scoreboard data and the actual scoreboard data in the arena How to Adjust the Delay With Control of the Scoreboard To adjust the delay when you can control the scoreboard proceed as follows 1 Record as you perform the following recommended game shot clock sequence in the arena a Point all cameras to the scoreboard game shot clock display b Startthe game clock at 2 00 and begin the countdown c Runthe shot clock multiple times from 24 to 0 0 d Runthe shot clock finally at 30 sec on the game clock until the shot clock reaches 0 0 red square around the basket lighting up e Letthe game clock run to 00 00 with red border 2 Jog back to the timecode when the shot clock reaches 0 0 step d and adjust the delay with CTRL Page Up Page Down to get the shot clock 0 0 on the video output at the exact frame where the square around the arena scoreboard turns red 3 Browse through all cameras and check that the delay is good on all cameras Otherwise adjust it as described on step 2 2 Configuration Ei V5 CONFIGURATION MANUAL 1 2 Epsi
22. working The button depends on the working mode selected in the parameters By default Epsio FX Reveal Mode operates in live mode and the timestamped scoreboard data is stored in an archive named on the pattern Record Yvvv MM DD When you will replay the PGM1 of the EVS server coming into the video input 1 connector of Epsio the scoreboard data will automatically be displayed on the video output EVS Broadcast Equipment SA Issue 1 2 A July 2015 2 2 1 Configuration Overview It is recommended to configure the EVS server and Epsio in the following sequence uU 2 3 4 5 6 Configuration Step Setting up the Multicam Parameters Launching the Multicam Configuration Installing a Custom Graphic Pack Configuring Epsio Parameters Checking the Information Screen Adjusting the Delay GUI EVS Server EVS Server Epsio Epsio Epsio Epsio The operations specified below are not part of the main workflow 1 2 Action Working Offline Managing Scoreboard Data Epsio Epsio and EpsioRevealDataSetManager bat Compulsory or Optional Compulsory Compulsory Optional Compulsory Compulsory Compulsory GUI 2 Configuration pum V5 CONFIGURATION MANUAL 1 2 Epsio FX Reveal Mode i 2 2 Setting up Multicam Configuring the Timecode Insertion Settings CEM In the Multicam Configuration module Channel page advanced view Timecode Insertion settings in the HD OUT section the valu
Download Pdf Manuals
Related Search
Related Contents
V7 Laser Toner for select HP printer - replaces Q5953A Tripod Portable Screens User Manual Sears KENMORE 46521 User's Manual TFA_No. 35.1104 Anleitung μTRONキーボード 取扱説明書[詳細編] USER MANUAL Copyright © All rights reserved.
Failed to retrieve file