Club Scene
Contents
1. DM Channels 1 16 Showselect L 1 l Showselect H 2 none only show 0 15 Speed Kpps 3 l i none use value in showtable Framerepeat 6 none use value in showtable Size 4 none use alue so Offset X A none use value 128 Offset 5 l none use value 128 Blankshift 8 M none usevalue 4 Intensity 12 W none use value 355 E Fig 3 DMX channel selection Showselect L This DMX function cannot be disabled Input here the channel for show selection When just this channel is used for show selection one of the first 16 shows including Pause can be selected Showselect H Input the channel number corresponding to this function here 16 banks of shows 16 shows each can be selected using this function When DMX control of this function is disabled only shows number 0 pause to 15 are selectable from the control desk Speed Kpps Input the channel number corresponding to this function here2. loop interuptable sc 7 qu pen La a ero etal etfs ett eft eft eruuy wild eff 0g ild a Lod ild ild ild ild ild ild 12 0 w Ma N Fe to Pa Ca Ta Dan Taa Dan L L L L ani L L L L L Fig 4 Showtable loop interuptable loop interuptable loop interuptable loop interuptable loop interuptable loop interruptable loop interuptable loop interuptable When clicking in a row under Filename a dialog opens for selecting a file The same file can be used in different rows of the table Watch that the card removable media is selected as the path Then you can be sure that your show file is available on the card It is also possible to work in a backup directory on the hard disk and then copy the whole content to the memory card But then it must be sure that there are short filenames available This is normally only sure when using FAT file system Otherwise Windows will create a short filename
3. WD Data nem DHX Yalue Filename Speed pps Framerepeat Displaymode Coie mm m Fig 5 Speed pps 20000 Fig 6 Speed pps Framerepeat Fig 7 This value only will be used when framerepeat is not controlled by DMX channel Framerepeal Fig 7 framerepeat Displaymode Fig 8 Here one of four possible displaymodes can be selected PAUSE is fixed to one mode and the TRIGGER shows only offer 2 modes Displaymode is the combination of 2 showmodes and 2 priority modes Displaymode loops interuotable oneshot complete oneshotyinteruptable loopcomplete loop intenruptable Fig 8 The 2 showmodes are Loop or Oneshot Loop When using this mode playback of the show will be repeated as long as no new show will be selected For example when the show only consists of one single frame this frame will be displayed permanently Oneshot The selected show will be displayed exactly one time When the show only consists of one single frame this frame will be displayed n times where n is the value under Framerepeat When playback of the show or frame is fi
4. 2 3 DMX channels assignmet Channel1 Show select L This channel is used for show selection one of the first 16 shows including Pause can be selected Channel2 Show select H 16 banks of shows 16 shows each 256 shows can be selected using this function Channel3 Size projection size When you change size by the use of DMX control a fader position of 0 minimum can cause a standing laser beam This can be a dangerous condition DMX only allows a refresh rate of 50 Hz Moving a control fader fast will result in jumps of the display settings Channel4 Offset X horizontal position A value of zero results in the maximum negative offset 128 is the center position and 255 is the maximum positive offset When changing this value via DMX the projected display can jump because DMX Signal rate is slow Channel5 Offset Y vertical position See Offset X Channel6 Frame repeat Shows in ILDA format do not contain any timing information When all frames of a show are outputted one after the other the animation speed is too fast By repeating every frame a number of times the speed of the animation movement can be cont
5. Input the channel number corresponding to this function here When you change size by the use of DMX control a fader position of 0 minimum can cause a standing laser beam This can be a dangerous condition It is recommended not to use this DMX control and use the fixed global value instead or to use laser projectors with a scanner safety circuit only This ensures the laser emission being shut down during dangerous conditions Also the scanners can be overloaded when increasing the scan angle at the same scan speed DMX only allows a refresh rate of 50 Hz Moving a control fader fast will result in jumps of the display settings Offset X horizontal position Input the channel number corresponding to this function here This setting has an unsigned value A value of zero results in the maximum negative offset 128 is the center position and 255 is the maximum positive offset When changing this value via DMX the projected display can jump because DMX signal rate is slow When DMxX control of this function is disabled the value set behind global Value will be taken For center position use a value of 128 Offset Y vertical position
6. DME 52 contol The device has 10 operating channels If you set the first on DMX address 1 the next DMX device can follow at address 20 DMX channels assignment DMX512 Channel FUNCTION VALUE Sound control 3 10ch useless 1 Control Mode 64 127 Auto mode 3 10ch useless 16 25 green 3 Pattern 124patterns 0 255 4 Vertical Move 128 191 auto down speed up accordingly 192 255 auto up speed up accordingly Hon TT P l 0 127 manual horizontal A 5 Horizontal T Move 128 191 manual right speed up accordingly T 192 255 manual left speed up accordingly E 0 127 manual vertical rotation R 6 Vertical Roll N 128 255 auto vertical rotation speed up accordingly 0 127 manual horizontal rotat
7. This function controls the output speed points per second The POSEIDON can output a maximum speed of 30000 points per second and 1000 points per second minimum Keep in mind that changing the point output speed also will change the speed of the displayed animation and also will influence the blanking settings blank shifting For this reason the speed should be adjusted carefully When DMx control of this function is disabled the value set in the showtable individual for every show is used Framerepeat Input the channel number corresponding to this function here Shows in ILDA format do not contain any timing information When all frames of a show are outputted one after the other the animation speed is too fast By repeating every frame a number of times the speed of the animation movement can be controlled Common used values are 3 6 Values by DMX control are 1 to 16 When DMx control of this function is disabled the value set in the showtable individual for every show is used Size projection size
8. and X invert X and Y changed and Y invert X and Y changed and both inverted N Ooh WM A O 2 2 Message center If any error condition occurs a code will be displayed on the status LEDs see table Not all errors will cause a stop of playback Errors from the memory card read write will cause a total shutdown of the player If there is no card or the card is not inserted correctly of if there is no right format or file system the player functions will be shut down When there is no file allocated to a selected show number this is no error condition and the player will switch the output to Pause Shown umber 0 PAUSE When the accessed show file is not valid or corrupted the playback will be switched off All other functions keep running and the selection of another show is possible Ready DMX Data Error Yellow No MMC SD card Yellow Red File system FAT16 not found Yellow Yellow Red Data error when reading MMC SD card Yellow Yellow File not found or invalid file Yellow X No DMx signal Yellow Green Ready
9. switches to PC MODE position and then connect the PC ILDA output interface to the ILDA IN connector on the rear panel using the included PC Controlling Cable If you want to make your own cable you should comply with the blow signal definition table of ILDA DB 25F pinouts 5 to 5V 5 to 5 V Connect to ground 15 Connect to ground Ground 25 Cable shield Caution Because the device is equipped with scanner of 20Kpps so you should do tune down the setting of scan rate below 20K per second when you use software Pangolin Mamba Phoenix etc to control the device Too high scan rate will be greatly harmful to the scanner and we will not be responsible to the damage for that
10. when copying data to memory card and the names would be changed The player then will not find the filename on the card It is better first to place all show files on the memory card and then selecting them directly from the card Note for Windows 2000 or Windows XP with NTFS file system NTFS will not create short filenames or change the names when copying files to the card It is recommended first copying all show files to the card and then select all files directly from the memory card when making configuration Speed Kpps Fig 6 This is the output speed point rate for the current show This value only will be used when the speed is not controlled by DMX channel The lasershow player supports a maximum output speed of 30 Kpps 30000 points per second When using a value greater than 30000 the player limits the speed to 30K internally When clicking into the field Speed Kpps a dialog opens where speed framerepeat and displaymode can be selected Copy and paste can be used to copy all values of a row into another row of the showtable Fig 5
11. See Offset X Blankshift Input the channel number corresponding to this function here This function can be controlled in 16 steps Here the timing of the blanking Laser off and the colors can be controlled Because the scanners are slower than the changes of colors or blanking these changes have to be delayed Common used values are 2 to 5 Possible values are 0 to 15 When DMx control of this function is disabled the value set behind global Value will be taken A global value for all shows often is critical because different shows need different settings The best solution is to adjust the value via DMX and save the settings together with the show selection as a scene on the DMxX desk Note Changing the point speed Kpps will also make it necessary to change blankshifting The Showtable Fig 4 In the showtable all DMX values of the channels ShowselectH and ShowselectL are listed giving a maximum count of 256 shows plus 2 separate shows for Trigger inputs A showfile and several show parameters can be allocated to every DMxX value When only using ShowselectL for showselection rows from 16 to 255 don t care because only 15 shows plus Pause can be accessed by DMxX control
12. User Manual Hadfield Management Ltd Laser UK Club Scene TRI COLOR LASER SHOW SYSTEM LASER UK Club Scene amp Please read this manual carefully before you initially start up OPEN THE BOX FOR CHECKING Thank you for choosing of this product Club Scene Tri color Laser show System In order to use this product safety and reasonable please read over this manual carefully before use and the operation must strictly according to this manual to avoid any damage to the product and personal safety Once you receive this product please immediately take it out carefully and check whether the product was damaged during the transportation Then please check if the following parts are included Club Scene laser projector Power cable DMX signal cable User manual Specifications Laser type Laser class Laser life Cooling ways Color Laser output Scanner system Optical angle Control mode Power supply Power consumption Dimensions Net Weight 1pc 1pc 1pc 1pc Green Laser Diode Pumped Solid Stated Laser DPSSL Red Laser Semiconductor Diode Laser Class IV gt 5000 Hours Air cooled Red 650nm Green 532nm 180mW 120mW 650nm 6 O0MW 532nm 20Kpps optical scanner O 20 Sound active Auto mode with simultaneous operation USITT DMX512 10channels Playback of ILDA lasershow files in SD card 6channels ILDA 25 pin Interface for PC controller AC 110 240
13. V 50 60Hz lt 300W W200mm xH260 mm xD450 mm 6 0Kg DANGER LASER RADI ATION Avoid direct eye exposure Laser radiation can cause eye damage and or skin damage All protective measures for a safe operation of this laser must be applied Safety instructions If the device has been exposed to drastic temperature fluctuation do not switch it on immediately The arising condensation water might damage your device Leave the device switched off until it has reached room temperature The laser must only be used for shows The operation Is only allowed if it is controlled by a skilled and well trained operator Never leave this device running unattended and keep it away from children and amateurs Keep away from heaters and other heating sources In order to safeguard sufficient ventilation leave 50 cm of free space around the device Never direct the laser beam to people or animals CAUTION LASER DIODE Never unscrew the housing There are no serviceable parts inside the device Maintenance and service operations are only to be carried out by authorized dealers Always disconnect from the mains when the device is not in use or before cleaning it HEALT HAZARD Never look directly into the light source as sensitive persons may suffer an epileptic shock Operating determinations The operator has to make sure that laser radiation also reflected laser radiation higher than the highest al
14. ay suffer damages and the guarantee becomes void Furthermore any other operation may lead to dangers like short circuit burns electric shock Product Rear View LDAN ILDA THRU ee aTLaserTecHNotocy _ a D VOLUME Volume sensitive Message center Indicating the state of SD card controlling system SD Card Controlling Used to set some important parameters for SD card Settings SD Card SD Card maximum capacity of 1 Gigabytes support Select the operating modes DMX 512 signal input DMX OUT DMX 512 signal output START DDRESS Setting the DMX start address w ILDA IN ILDA standard signal input EE ILDA THRU ILDA standard signal through Ea ON OFF Key switch for powe
15. ddress ILDA Player MPIZC LX r Sax DMX Channels 1 16 Showselect L 1 Showselect H 2 none only show 0 15 Speed Kppz i none use value in showtable Framerepeat 6 none use value in showtable Size 4 none use value Offset x 4 none use value Offset Y 5 none use value Blank shift ge isl i none use value A Intensity 12 l V none use value 255 10000 loop intenruptable E 0000 1 loop interuptable 0000 loop interuptable 0000 1 loop interuptable 0000 loop intenruptable U000 loopinteruptable U000 loop interuptable 0000 loop interuptable 0000 1 loop interuptable Save Config Print Fig 1 Configuration software Input here the DMX base address from where the group of 16 control channels starts Possible values are 1 512 Maximum sum of base address plus highest used control channel is 512 Any overflow will be watched by the software and a message will be displayed Global Data DM gt B aseaddress 1 Fig 2 Global settings Setting up DMX channels Fig 3 Each parameter control can be placed to any channel starting from the base address By checking NONE DMX control can be disabled and a fixed value can be used
16. ed Oneshot Complete The show will be displayed completely exactly one time Oneshot Interruptable The show will be displayed exactly one time but will be aborted when a new show is selected Exceptions Show number 0 Pause is always Loop Interruptable Triggershows will be displayed only one time Oneshot because these shows will be selected edge triggered Note When a show is running in Complete mode all parameters like speed size offset framerepeat and blankshift will be held also when controlled by DMX Otherwise the parameters would be changed when selecting a new show during playback of the current show The Pauseshow Normally the filename at show number 0 Pause is left blank When selecting Pause or after finishing playback the laser is blanked and the output is stopped In some special cases for example when using the system as an advertising display without DMX it could be necessary to playback a show without any additional control When placing a show file to show number 0 pause this show always will be outputted when no other show is selected Useful combinations of display modes Long shows should be interruptable to allow changing to another show Short shows or short effects should be set to Complete Single frames should be set to Loop because otherwise they just will be displayed parts of a second Special sequences as a highlight of a show should be set to Oneshot 3 PC MODE Put the mode
17. ion 7 Horizontal Roll 128 255 auto horizontal rotation g 8 Rotation 128 191 auto clockwise rotation speed up accordingly R 192 255 auto anti clockwise rotation speed up O accordingly from small to large speed up accordingly U 9 Zoom In P 8 Out 86 170 from large to small speed up accordingly ne oa large small speed up accordingly 10 Pont Draw Point Draw 0 255 0 nil 1 255 faint bright 2 SD Card Controlling Mode 2 1 SD CARD Controlling Settings Panel The panel can be used to access some important parameters for the ILDA projector If the memory of the panel is empty it displays Err at power on At normal function if parameters are set correctly the panel displays the actual DMX base address for exa
18. lowed level is avoided by technical or organizational measures Make sure that the used voltage is AC 110V 240V 50 60Hz with ground If the device is used in a flying installation the mounting brackets and an appropriate Safety rope must be fixed Laser effects are not designed for permanent operation Consistent operation breaks will ensure that the device will serve you for a long time without defects In some country the operator must notify the accidence insurance and the authority for industrial safety before operating a laser For more information contact the relevant authorities Please consider that unauthorized modifications on the device are forbidden due to Safety reasons If this device will be operated in any way different to the one described in this manual the product m
19. mple 001 There are 3 keys from left to right gt 1 FUNC By pressing FUNC the actual parameter for changing is selected There are 2 parameters currently available Adr DMX base address Ort orientation of the projection gt 2 SEL After selected the parameter with FUNC press SEL and the current stored value will be displayed By pressing SEL again the digit for changing will blink Pressing Select multiple times will activate all digits by blinking one after the other gt 3 Up Use this key to change the current number in the blinking digit The number will be increased When reaching the maximum number 9 the number will be start from zero again Example Set DMX base address to 200 Press FUNC until Adr blinks Press SEL until current value is displayed and right digit blinks Press Up until 0 is reached Press SEL to go to middle digit Press Up until 0 Press SEL until left digit blinks Press Up until 2 is reached Press FUNC for exit this parameter The value is stored automatically All values are stored and activated when exit the parameter input by pressing FUNC parameter The value is stored automatically After not changing anything in the parameter input routine the panel will return to main routine after about 10 seconds without storing value to memory Note that playback of longer shows may be interrupted
20. nished and no new show is selected for playback the player automatically will switch to PAUSE show 0 The 2 showmodes can be combined with 2 output priorities These are Complete and Interruptable Complete The current running show will be outputted completely before any new showselection is possible Interruptable The current running show will be aborted when a new show is selected The following combinations are possible Loop Complete The current show always is displayed completely and will restart from the beginning when no new showselction is recognized at the end of the show Loop Interruptable The current show will be repeated when no new show is selected When selecting a new show the current running show will be abort
21. r supply E3 AC IN AC 110 240V 50 60Hz OPERATION INSTRUTION MODE SWITCHES 1 2 3 1 Sound amp DMX Control mode You can choose Sound or DMX control mode through the 10 switch While it is switched to OFF position the equipment works in sound auto mode While it is switched to ON position the equipment works in sound mode 1 1 Sound Auto mode When the 10 switch is OFF 1 9 are function codes Here the functions as bellows lf the 1st switch is OFF the equipment works in sound mode lf the 1st switch is ON the equipment works in automatic mode Function code setting Function Dip Switches Sound mode DMX mode function switch Auto Mode Pa Slave mode For master slave mode put the 2nd switch to ON position and it works as slave Synchronized Connections and Settings n Gurl MASTER 7 J war 235345 7849 DO 2445 T 9 10 345 THO W Sound mode ON i ON ir BOG Auto mode 1 2 DMX Control mode For DMX mode the 10th dip switch must be ON Then set the DMX base address with the binary system 0 or 1 through switch 1 9 Examples DMX DMX address address A Ta A T o E mbH g seer nuro NIAS Ci Le Ey Gia rel h fro Fa 6 4 asl Gi h foe E Ae H AUURUNAMG eR NF oF me fe N allel DMX base adds 1 10 setting ON is 1 OFF is 0 en T T Sound Coral 1 0 0 0 0 0 0 0 0 0 yo w 1 1 0 0 0 0 0 0 0 0
22. rolled Values by DMxX control are 1 to 16 2 4 Memory card Compact Flash card All Compact Flash cards up to a maximum capacity of 2 Gigabytes can be used 2 4 1 Important lt The card has to be formatted with FAT 16 file system only lt The manufacturer recommends the use of high quality cards No name Cards can cause read errors lt All cards shipped together with the equipment are formatted correctly and must NOT be reformatted 2 4 2 Caution When using own cards or reformat cards by using a PC with Windows operating system it is not ensured that the cards are formatted FAT16 Depending on the memory size of the card Windows can format these to FAT12 FAT16 or FAT32 file system The Poseidon will not work wi
23. stopped when changing parameters at he panel during show output Display of single frames of short sequences normally will not be interrupted Limits DMX base address 1 512 Intensity 0 99 Orientation 0 7 Limits will be controlled automatically by the panel If trying to set a value beyond the limits the panel automatically corrects to an allowed value during input Intensity For the projector this value should be set to 99 Orientation There are 8 different values possible allowing all possible projection orientations This is important for back projections or if it is not clear how the projector is installed at the location normal X invert Y invert X and Y invert X and Y changed X and Y changed
24. th other file systems than FAT16 Avoid formatting the card by the use of a PC with Windows operating system No subdirectories are supported by the Poseidon All show files and configuration files must be placed in the root directory of the card Subdirectories are allowed but cannot be found by the Poseidon system There may be not more than 260 files located in the root directory It is recommended not to store more files as necessary on the card Only short filenames will be processed 8 3 format by the Poseidon The Poseidon does not support long filenames The name of the files should be not longer than 8 characters plus the extension for example ILD When copying files to the card both long and short filenames are created The Poseidon only reads the short names The long names need additional space in the root directory To avoid losing space and limiting maximum possible number of files the names should be kept as short as possible Short filenames are not case sensitive 2 4 3 Reserved Filenames Some filenames are reserved for device control These files will be read out by the Poseidon automatically and must NOT be deleted or renamed The following filenames are reserved CONFIG DAT Contains output settings for the Poseidon FLASHMP BIN Controls program for firmware update FWUP12C BIN File for a specific firmware update When this file is found the Poseidon automatically updates the firmware After
25. this procedure this file will be deleted automatically by the Poseidon 2 4 4 Creating the Configuration file CONFIG DAT The free software tool inside the SD card shipped together with every Poseidon allows the creation and modification of the configuration file DMX base address can be set and every control parameter can be directed to a specific DMX channel inside the group of 16 channels Also DMX control of every parameter can be disabled and a fixed value can be set instead Edit Config dat Global Data DM B aseaddress 1 Preset t es l eff001 ild effO02 ild effO03 ild effO04 ild eff005 ild effQ06 ild eff ild eff00s ild C a aa Tan II Hew Config 12 0 J Om cn ee to ho DMX Base a
Download Pdf Manuals
Related Search