Quick-Start Guide
Contents
1. Power On Off press on off button press key to choose LIGHT ON Send Button press send button The below message will appear for a short time confirm with Enter all targeted lamps should turn on choose BLACKOUT confirm with Enter all targeted lamps should turn off Press this button if lamps are getting out of synchronisation The send button re sends the current effects and configurations to the lamps Configurations are also sent while changing settings the Send button simply re sends them Factory Reset of Remote Control press minus until SETUP press Enter press button confirm with Enter confirm with Enter confirm with Enter Factory Reset of Lamps press minus until SETUP press Enter Create a Set press minus until SETUP press Enter 2 x Confirm second blinking lamp by pressing its button and watch rapid blinking as confirmation lamp 3 and 4 Create a Chain press minus until SETUP press Enter confirm first blinking lamp by pressing its button and watch rapid blinking as confirmation press button Set Group press button until SETUP confirm with Enter press button choose any number confirm with Enter Continue assigning possitions for in the same way press button choose Remote Setup confirm with Enter press button confirm with Enter choose pixels of set confirm with Enter press Enter confirm with Enter Confirm first blinking lamp2. by pressing Troubleshooting This is the most basic function and great for testing if a remote control works with a lamp If this is not working you probably target the wrong lamps Check the Target Lamps chapter Other solutions are checking the Radio Pin and making sure your products have the same frequency 868MHz in Europe 915MHz in USA Always reset the remote control before starting a new lighting installation The remote and or lamps might still have some commands stored press button of each lamp you want to reset press button its button and watch rapid blinking as confirmation Press Home button your Set is finished now This guide is for 4 lamps with 1 pixel each If you have lamps with more pixels count all pixels together when calculating Size of Set You can create a set for a single lamp that way you are able to address it individually later confirm with Enter choose how many pixels your chain has confirm with Enter confirm second blinking continue assigning lamp by pressing possitions for its button and watch other lamps rapid blinking as in the same way confirmation press Home button your Chain is finished now SET position 8 TAP LAMPS NOW confirm with Enter confirm Remote Group with Enter choose any of the 4 Groups press Enter Chains and Sets are very similar to each other The main difference is that you can set hundreds of sets but only 1 chain A
3. e ART3 wireless DMX transmitter for additional information about using Astera lamps with wireless DMX Astera ARC2 quick start guide v1 6 2011 Astera LED Technology GmbH for additional functions please refer to the User Manual or contact your sales agent
4. lso a set can be part of a chain that makes it easier to handle a large amount of lamps confirm with Enter to send this group to all targeted lamps Home Button press Home button The below message will appear Change Program press Prog button press and buttons to select a program Change Colors press any of the color buttons C1 C4 set color with and buttons Change Brightness press brightness button confirm with Enter set brightness with and buttons This button lets you return to the top level navigation Use it to quickly return home when lost in the menu It can be pressed from anywhere inside the menu The following configurations only work while in HOME direct control to save program Each program except RAINBOW cosists out of 1 4 colors These colors will be set in the next chapter confirm with Enter press another button to change another color set color with and buttons confirm with Enter confirm with Enter to save value instead of Intensity you can change the Power Scheme of the lamps refer to the user manual booklet for information about that MEMORY programs press button press any of the 8 white buttons to launch a program Tap sync press Tap sync button twice check speed values decorative program is playing to reach MEMORY 2 4 Each MEMORY tab has 8 programs that can be launched by pressing the white buttons That means a total
5. of 32 MEMORY programs MEMORY 1 has decorative programs MEMORY 2 has slow party programs MEMORY 3 has heavy party programs MEMORY 4 can be programmed by the user Press and buttons to switch between the 4 MEMORY tabs and the SETUP rere are displayed in this speed Tap sync lets you synchronize the lamps with a beat or pattern The frequency of 2 taps is measured and displayed in seconds and beats per minute 3 kinds of colors can be selected 11 standard colors 255 index colors a mixed color out of RGB channels Change Fade press the fade button set fade with and confirm with Enter to save value Change Speed press the speed button set speed value with and buttons confirm with Enter Target Lamps press Target Lamps button choose if you want to target a set group individual lamp confirm with Enter Target all lamps in range press Target Lamps button choose Target lamps by Groups confirm with Enter The speed of a Program is displayed in minutes and seconds The displayed value is the duration of one cycle of the displayed Program The more time you select the slower the program is displayed if asked select a set or group number confirm with Enter press button until confirm with Enter all 4 Groups are selected Send a DMX address to a lamp press Target Lamps button click until Target lamps by TAPPING THEM confirm with Enter confirm with Enter selec
6. t which DMX address you want to send confirm with Enter all lamps in range should start to blink slowly press minus until SETUP press Enter press button until press the button of the lamp or lamps that you Each Group or Set can contain one or many lamps To control an individual lamp create a Set for it or Target Lamps by Tapping them confirm with Enter DMX setup Setup DMX SETUP the lamp should show a short rapid blinking want to take this DMX address to confirm that it accepted W the DMX address W W Le Radio pin make sure the lamp you want to pair with the remote is turned on W confirm with Enter hold down the on off button of the lamp until it blue LEDs start blinking rapidly blue mode f set any number confirm with Enter press plus until PAIR WITH LAMPS Radio PIN press minus until SETUP press Enter Confirm with Enter press button until Radio Pin confirm with Enter display shoud show Pairing Radio PIN enables you to set a unique frequency for lamps and remote That enables you to use 2 remotes in 1 room without disturbing each other s lamps You can achieve a similar effect by creating different sets and targeting each set at a time press the button of the lamp or lamps that you want to take this DMX address select another DMX address lamps that need DMX addresses continue with all other D Please refer to the manual of th
Download Pdf Manuals
Related Search