Inno INA744 BoardLocker Surfboard Rack Instructions Manual
Contents
1. fhe Installation manual lower clamp and tighten R washer Using the Board Carrier Loading boards Release lock open cover and draw out cable while lifting release lever 1 Cable cannot be drawn out unless release lever is lifted Cables Release 1 Remove cable from hook and load board Board Hook M Guide cable loop over hook and turn ratchet knob with both hands to reel in cable 13 N CAUTION Be careful not to overtighten cable as board may crack or deform Cable Ratcheting Knob Adjust position of protective pad on cable so that it Close cover and lock with key contacts and protects the edge of board Protective Pad When stacking multiple bare boards do not allow cable to contact boards N CAUTION If cover is not locked release lever may open accidentally causing board to drop Cover will not stay closed unless locked by key Genuine Replacement Parts Crane cover The following genuine replacement parts are available for this carrier Specify the part number when ordering any part from the store where you purchased your system The specifications and external appearance of the carrier Key system and genuine replacement parts are subject to l i mE l Note key number change without prior notice in the interest of product improvement User s manual Contact Information configuration or specifications If you have any complaints requests or comments2. ay not be tight enough Make sure to check that the clamp is mounted securely by checking for play between the clamp and crossbar Installing Carrier on Factory Cross Bars Remove the rubber pads from the top half of each clamp Install the 2 round bar adapters sold separately on each bar keeping a distance of 28 25 inch 720 mm between adaptors This distance is measured from the center of the adapter Mount adapters so that they are parallel to the ground 28 25 inch 720 mm Round bar Round bar adaptor Place clamp over the round bar adaptor Continue following the mounting directions for Installing Carrier on Factory Cross Bars O Remove the rubber pads from the top half of the clamps Follow the mounting directions in the Installing Carrier on Factory Cross Bars section 9 installing Carrier on Aftermarket Square Bars US If the space between the crossbar and the roof is tight the tip of the bolt may contact the roof If this happens reverse the hex bolt according to the following steps 1 Knob Remove the plastic knob from the nut by pushing down on it as in the illustration a m4 A KKU __ Hex bolt _ Remove the R washer from the other bolt in the same manner Cr CCG 7 R washer _ Insert the hex bolt into the SEG knob remove in step 1 _ Insert the nut into the R washer CMA 6 Continue following the steps in _ Insert the knob bolt through the
3. cked release lever may open accidentally causing board to drop This system is a theft deterrent Boards should not be left unattended for long periods of time Release the lock and open cover 3 For installation on Factory Cross Bars go to step 4 For installation on Aftermarket Round Bars go to step i For installation on Aftermarket Square Bars go to step It is possible in the course of normal use the carrier may leave marks on the crossbars Open the clamp by pulling the lever until it is pointing away from the carrier as in the illustration Slide the knob out from the lower half of the clamp Loosen both knobs so that they are at their loosest position Place the carrier onto the cross bar Installing Carrier on Factory Cross Bars Slide the lever side knob back into the slot in the lower half of the clamp With the lever in the opened position tighten both knobs until you just begin to feel tension Do not overtighten Try to keep the lower half of the clamp parallel to the bottom of the crossbar when adjusting knobs D Installing Carrier on Factory Cross Bars Close the lever In the closed position the smooth side of the lever should face up If the lever is too tight to close loosen it by turning it counter clockwise one complete revolution Try to close the lever again Repeat this procedure until you can close the lever The lever should not be too easy to close If the lever is too easy to close it m
4. eful not to hit the surfboards or sailboards with the vehicle s tailgate or trunk lid In case your gear is accidentally hit by the tailgate or trunk lid be sure to check the carrier s mounting condition Be sure to lock cover with key before driving If cover is not locked release lever may open accidentally causing board to drop This system is a theft deterrent Boards should not be left unattended for long periods of time We cannot guarantee the performance of racks or crossbars made by other manufacturers when used with the Board Locker Please make sure that they are installed correctly and in good condition Do not attempt to modify your rack If multiple surf sail boards are stacked rear end must be higher than front end If front end is higher air resistance increases and may place undue strain on carrier Do not load sail boards or long boards in bag Only short boards can be loaded in bag Do not make hard starts unnecessarily sharp turns abrupt maneuvers or sudden stops In case you have to perform such a maneuver always check afterwards to see that the carrier and cargo remain secure Do not drive your carrier through a car wash Always remove the carrier system before running your car through a car wash Daily care and storage 1 Wash any mud off the carrier system a Use a damp cloth to wipe away dust and dirt Do not use thinner or other solvents Clean the carrier system and check
5. for the A Store all components of the carrier system together in one place to prevent any component from following being lost Avoid storage in areas subject to direct sunlight high temperature or excessive humidity 1 Worn screw threads 2 Key deformation 3 Holder deformation 4 Cracking in the components of the carrier system US siie
6. please contact us listed right CARMATE shall not be held liable for any accidents or incidental losses arising from improper installation or use nor for those arising from installation or use after the customer has made any change to the system s original Specifications and exterior design are subject to change without notice for purposes of improvement mnno CAR MATE USA Inc 383 Van Ness Ave Suite 1603 Torrance CA 90501 U S A ORNATE EE EAE EATE support nnoracks com www innoracks com yz ETI INA744 BOARD LOCKER q SS Se eS Locking Board Carrier ii OD Guidelines Read and understand this user s manual thoroughly before using the your new board carrier and be sure to follow all usage instructions Keep this manual in a safe place so that it s handy for reference anytime If you sell or give away the board carrier provide this manual to the new owner to ensure safe installation and usage If you have any questions regarding the information in this manual please contact the service center listed at the end of this manual AN Caution There should be a distance of at least 19 7 inch 50 cm between the front and rear crossbars At least 19 7 inch 50 cm Obey all posted speed limits Drive slower under strong winds or on rough roads Before driving shake board in all directions to inspect belt tension Retention loose belts If a short board is loaded in a bag secure it firmly to prevent moving Be car
7. sted at the end of this manual G Frame bar assembly 2 ky tt Installation Instructions 1 Preparing for Installation The distance between the front and rear carriers must be at least 20 inch 50 cm If necessary adjust after market or factory installed crossbars to meet this minimum distance At least 20 inch 50 cm This product will fit square round amp most factory crossbars 1 If you do not have factory crossbars mount the carrier stays and bars according to the procedures described in the Basic Carrier System Installation Instructions 1 Round bars require adapter sold separately Some factory crossbars require long bolt kit sold separately E MAXIMUM CROSSBAR SIZE H 3 5 inch 90 mm H 1 2 inch 30 mm 1 2 2 0 inch 30 50 mm Without option Needs long bolt kit Mount your base rack system according to the procedures described in the installation instructions for the rack Consult your vehicle s owner s manual for information regarding the operation of your factory installed rack if it will be used for this application N CAUTION The distance between the front and rear crossbars should be at least 20 inch 50 mm After installing and before driving the vehicle shake the attachment in all directions to ensure that there is no looseness in any of the four mounting knobs Retighten any loose knobs Be sure to lock cover with key before driving If cover is not lo
8. yz ARTO INA744 BOARD LOCKER ADVANCED CAR RACKS Locking Board Carrier 5474 70978C US J Installation Instructions The following Installation Instructions explain how to mount and use the INNO system carrier attachment system designed for loading 3 surf boards or 2 long boards After reading this manual keep it in a safe place along with the installation instructions for attachment systems If you have any questions regarding this manual please contact us listed at the end A CAUTION Failing to observe these cautions may lead to accidents that may cause death or serious injury N These notes explain points that you should know about when using the ote roof box A ATTENTION Failing to observe these attentions may lead to injuries or damage to the roof box vehicle and surrounding objects CAUTION This is a dedicated attachment for carrying up to 3 short surfboards or up to 2 long or sail boards Maximum loading capacity varies depending on vehicle type Check appropriate limits for your car in the Fit Guide Do not load objects other than surf or sail boards Follow the illustrations below when loading boards If multiple bare boards are stacked do not allow cables to contact boards cables may scratch board surface The Board carrier includes the parts listed below Verify that all parts are included with the carrier you have purchased In the event any of these is missing contact our service center as li
Download Pdf Manuals
Related Search