User Manual
Contents
1. Wireless Remote Prepare the wireless remote for use by removing the battery insulating tape The remote uses a 3V CR2025 battery Note The wireless remote operates using radio frequency The remote controller s use is not restricted by normal obstructions such as walls doors etc 13 LED Controller Status Indicator A multi color emitting LED located on the remote controller indicates current operating status or operating status changes as follows iL 4400 Earth City Expy St Louis MO 63045 Waterproof LED Controller The MCBRF RGB10 LED controller is fully waterproof according to the IP68 standard and can be installed and operated underwater up to a depth of 30 meters Note LED controller sensitivity to wireless remote signals will decrease when operated in underwater conditions Make sure to perform all wiring connections and setup prior to installing LED controller underwater 866 590 3533 superbrightleds com2. ive static color Initiates Static Color Mode if Dynamic Mode is currently active 8 Direct Color Select Activates the static color indicated by the button color These individual colors are also accessible through the Ascend Descend Static Colors buttons 9 Wireless Remote LED Indicator Flashes blue when remote is operated to indicate that remote is functioning properly RGB LED Controller 10 Power Supply Wiring The controller power supply operates on 5 24VDC The red wire is positive and the black wire is negative as indicated on the controller housing 11 LED Output Wiring The controller supports common anode type LED prod ucts Output wires are indicated as follows Black V Common node which connects as the positive line connection inside the controller Red R Wire connection for red LED color signals Green G Wire connection for green LED color signals Blue B Wire connection for blue LED color signals Light Signal normal functioning mode 12 Wiring Connectors Use wiring connectors to make connections between wiring Be sure to maintain polarity and wiring color when connecting wiring Dolphin connectors are shown here Blue Short single Long single white flash white flash lighting change Pairing A New Remote Up to 3 wireless remotes can be assigned to operate the LED controller Additionally each individual wireless remote can be assigned to an unlimited number of controlle
3. rs The following steps show how to assign a new remote to the LED Controller 1 Disconnect the power to the LED controller wait 5 seconds and reconnect 2 Within 5 seconds of reconnecting the LED Controller press the Mode and Speed buttons simultaneously 3 The LED indicator on the LED controller will flash white 3 times indicating the new wireless remote has been successfully assigned This may be done for a total of 3 wireless remotes Pairing Any Remote Up to 3 wireless remotes can be assigned to operate the LED controller The following steps show how to assign a new remote to the LED Controller 4 Disconnect the power to the LED controller wait 5 seconds and reconnect 5 Within 5 seconds of reconnecting the LED Controller press the On and Play Pause gt buttons simultaneously 6 The LED indicator on the LED controller will flash yellow 3 times indicating the LED controller will recognize any remote RGB LED Controller Status Indicator Blue flash Red flash Overload short f circuit has Dynamic mode is been detected paused activating protection mode Long single yellow flash Yellow flash Range limit has been reached when cycling through Tempo Speed Level or Static color Brightness Level Range limit has been reached when cycling through Dynamic or Static color modes Overheating has been detected activating protection mode Additional Features Using the
4. superinighticiscom Important Read all instructions prior to installation RGB LED Controller with Wireless RF Remote Parts Included 1 LED Controller 1 Wireless Remote Wireless Remote 1 Turn On Standby O Turns on controller or enters standby mode 2 Ascend Descend Dynamic Modes Dynamic modes feature a variety of static color transitions and patterns with 43 distinct modes These buttons initiate Dynamic Mode and cycle through the modes in ascending or descending order 3 Play gt Pause User Manual Part Number MCBRF RGB10 RGB10 P C mo T eo eo IP Grade IP 68 Waterproof oo T 900 O Ne RF Wireless yy Remote Pairing Options Toggles between run pause when in Dynamic Mode or Demo Mode Initiates Dynamic Mode if Static Color Mode is currently active 4 Increase Decrease Tempo Speed Level Increases or decreases the tempo of the currently active dynamic mode Initiates Dynamic Mode if Static Color Mode is currently active 5 Demo Mode Initiates Demo Mode Demo Mode cycles through 27 individual modes repeating each 3 times 6 Ascend Descend Static Colors These buttons initiate Static Color Mode and cycle through the colors in ascending or descending order 7 Increase Decrease Static Color Brightness Level Increases or decreases the brightness of the currently act
Download Pdf Manuals
Related Search