USER MANUAL - Pool Technologie
Contents
1. gt Select On to activate the mode or OFF gt to deactivate then press V gt to confirm gt If On gt is selected the temperature safety is activated SIMPLEO will stop the chlorinator as soon as temperature will be under 15 C SIMPLEO will operate the chlorinator and will handle a shock treatment for 48 hours in the beginning of the season It will be activated as soon as the temperature will remain above 15 C for more than 10 days IJIOLEL 13071 The temperature safety activation is indicated by a flashing 6 11 8 Ajusting the temperature sensor gt Enter the main menu and go to PA 08 menu The current measured temperature flashes gt Adjust the desired temperature 3 then press V gt to confirm The new temperature is recorded and the device switches to the main display 9 Temperature sensor Pro gt Enter the main menu and go to PA 09 menu gt Select On to activate or OFF to deactivate then press V to confirm Note If the sensor is deactivated all fucntions related to temperature will be deactivated Temperature control mode TEMP Low temperature safety Temperature adjustment menu Frost guard safety The deactivation of the temperature sensor will be indicated by the display of a line up right of the display alternatively with the time l VIII WARRANTY All our care and technical expertise h2. 15 16 17 18 21 22 Lo Le COVER FLOW TEMP EIE TRAITEMENT AUTOMATIQUE Ph N T T N Ph T N Ph B INSTRUCTIONS A swerro must be connected after a circuit braker and must control the pump by mean of a relay It can control a pump up to 600 VA maximum If the pump is larger it is necessary to use a contactor Electrolyseur Basic COFFRET FILTRATION ee Ce i CS FILTRE IA 230 V Contact Volet gd REFOULE Coe se Temperature CELLULE Option d bit ASPIRATION 1 Temperature sensor The temperature sensor must be installed after the pump and the filter but before the heater the pH regulation accessories and the chlorination cell gt Place the saddle while adjusting the 72 opening towards the bottom The opening may be adjusted towards the top however a bottom orientation will allow an optimal precision Mark then drill the pipe Screw the temperature sensor on the hole gt Plug the extension cable in SIMPLEO terminals 20 and 21 Plug the temperature cable in the extension jack socket 2 Pool cover connection gt Find the limit switch dry contact no current in the pool cover controller Some pool covers manufacturers specially mark this limit switch as it used for chlorinators gt By mean of a wire 2 conductors connect the dry contact in terminals 14 and 15 of SIMPLEO 3 Flow sensor The flow sensor must be located just after
3. line should be protected by a differential circuit breaker with a release security of 30 mA maximum with an opening distance of at least 3 mm on all poles This circuit breaker has nothing to do with the house s one from 300 to 500 mA In case of doubt get a qualified electrician to look at the installation The electrical installation of this equipment should be performed by a qualified person in accordance with the regulation in force in the region concerned The power supply cables and the cell must be protected against accidental damage A damaged cable should be replaced immediately and exclusively with an original cable Never cut or extend the cables It is important to turn off the power supply before carrying out any technical work Do not modify the device Any modification may cause damage or be dangerous Only qualified personnel should carry out maintenance in case of break down This device is intended for use in family pools only NON OBSERVANCE OF THESE INSTRUCTIONS MAY CAUSE DAMAGE TO THE DEVICE OR SERIOUS INJURY PACKING LIST Before starting installation ensure that the box contains YA v v v 1 User Manual 1 Electronic controller fitted in an IP65 housing for the outdoor model 1 temperature sensor and extension cable 1 34 saddle III PRESENTATION A APPLICATIONS 1 Filtration control refer to p 10 SIMPLEO is a smart module which has been designed to control automatically the fi
4. USER MANUAL SIMPLEO INDEPENDANT MODULE MOY YYYYYYYY YY ie E CA 0000000000000 LWA ey FAMILY POOLS C X R f PAPI004064 UK 10 09 TABLE OF CONTENTS SAFETY INSTRUCTIONS JI PACKING LIST IT PRESENTATION IV INSTALLATION V OPERATION VI WARRANTY VII ENVIRONMENT PRESERVATION Pool Technologies declares this equipment complies with the following E U directives Electromagnetic Compatibility Directive 89 336 EEC modified 92 31 EEC and 93 68 EEC Low Voltage Directive 73 23 CEE modified 93 68 EEC Chief Executive Gan SS To improve product quality the manufacturer reserves the right to modify production at any time and without notice SAFETY INSTRUCTIONS READ AN FOLLOW ALL INSTRUCTIONS SAVE ALL INSTRUCTIONS A In the manual this symbol indicates a WARNING It informs you of the risk of damage to the equipment or of serious injury It is very IMPORTANT that you pay attention to these warnings WARNING RISK OF ELECTRIC SHOCK The safety instructions outlined in this manual are not exhaustive They highlight the most common risks of using electrical equipment in presence of water Any installation and use of this equipment should be carried out with caution and common sense To prevent injury or accident install the equipment out of the reach of children Ensure that the installation conforms to the regulation in force in the region concerned The filtration box power supply
5. as gone into making this device It has undergone quality control If in spite of all care and knowledge which has gone in to its manufacture you have to use our warranty free replacement only applies to parts of our equipment which are defective transportation excluded Duration of the warranty v 2 YEARS for New equipment v 1 MONTH for AFTER SALES repair and spare parts from Authentic invoice date OBJECT OF THE WARRANTY The warranty applies to all parts with the exception of worn parts which must be replaced regularly The device is covered for any manufacturing defect only when it has been used normally in a family pool Use in public pools voids the warranty After sales service v All repairs are done in our work shop 12 All transport fees are payable by the user There will be no compensation for immobilisation and privation of the equipment when it is being repaired v In any case the equipment is always carried at the user s own risk It is up to the latter to check that it is in perfect condition before the order is collected and if need be to state any reservations on the carrier s slip Confirm this with the carrier within 72 hours by registered letter with an acknowledgement of receipt IMPORTANT A replacement under guarantee will on no account extend the initial warranty Limit of the warranty Not included in the warranty Equipment and labour provided by a third party at the time of the instal
6. de Montpellier 13 IX PROTECTING THE ENVIRONMENT Protecting the environment is essential Our company is very much involved in this Our products are designed and manufactured with materials and components which are of a high quality respect the environment and are reusable and recyclable However the different components of which they consist may not be biodegradable Our products should not just be discarded European environmental directives set the accurate management of older electronic equipments The aim is to reduce and to reuse wastes and to avoid making their components become a danger The symbol stamped on a product means that a selective collection 15 necessary and that it must be sorted from other household waste Consequently you must not dispose our product anywhere e you may drop it off at a waste collection organization e If you buy a similar device you may leave it with your seller at the time of purchase 14 15 Manufactured by POOL TECHNOLOGIE Zac des Jasses 115 rue de l Oliveraie 34130 Valergues France www pool technologie com 16
7. ers load The user has just to set off the function manually The mode will stop automatically 24 hours later v Wintering automatic activation of the chlorinator refer to p 11 In order to protect the chlorination cell and hence to increase its lifespan a chlorinator should be stopped as soon as temperature decreases under 15 C SIMPLEO will automatically stop the chlorinator when temperature will decrease under 15 C As soon as the temperature will get above 15 C SIMPLEO will activate automatically the chlorinator and SIMPLEO will set off a choc treatment for 48 hours v Frost proof protection During winter SIMPLEO will protect your installation against frost by activating the filtration 24 24 h when temperature is under 15 C v No flow safety refer to 11 SIMPLEO may be equipped with a flow sensor option in order to protect your installation in case of no flow in the pipes B MODELS 1 SIMPLEO standard model To be mounted on the DIN rail in the filtration box in place of the manual timer To be mounted safely and independently by the filtration controller thanks to its watertight box INSTALLATION DIAGRAM SIMPLEO Chorinator automatic treatment control Filtration control Pool cover conncection IV INSTALLATION A ELECTRICAL CONNECTION example single phase connection Contact sec Capteur Sonde volet d bit temp rature OG
8. lation of the equipment 2 Damage caused by an installation which is non compliant 3 Problems caused by deterioration accident harsh treatment professional negligence or by the final user non authorised repairs fire floods lightening frost armed conflict or any other force majeure CAUTION The warranty does not cover any damaged equipment further to non respect of security use rules use and maintenance stated in the current manual Every year we improve our products and software These new versions are compatible with previous models New versions of equipment and software are not added to the warranty from the previous models Implementation of the warranty v For more information on the current warranty get in touch with a professionnal or our After Sales Service Any request should be accompanied by a copy of your proof f purchase Y Do not hesitate to activate your guarantee on www pool technologie com It will enable you to receive information on your device v No part replacement will be made without the defective part being returned beforehand Any part which is not returned will be charged at the current tariff Laws and disputes v The present warranty is subject to French law and all other European directives or international treaties which are in force at the moment of complaint and which are applicable in France In the event of dispute with regard to its interpretation or its execution this is the remit of TGI
9. ligent control according to the temperature CEP a gt Enter the main menu and go to PA 02 menu gt Select TEMP gt then confirm with gt TEMP gt remain displayed the control by the temperature is activated and the device returns to the main display b TIME manual setting SIMPLEO can also be manually set in order to allow the user to customise up to 8 operating slots gt Enter the main menu then go to A 02 menu gt Select TIME and valid with V the display switch to time slots settings 8 available slots and TS 01 gt flashes Time slots setting gt Enter the desired slot ex 15 01 and valid with V gt The starting hour of the slot is displayed gt Set the starting hour adjust the first 2 figures for the hour and press V to confirm then adjust the 2 last figures for the minutes and press V to valid The display switches then to the stop time of the slot gt Adjust the stop time in the same way and press V gt to confirm When the time is recorded the display switches to the slot starting time To set the other slots go to the desired slot TS OI gt to TS 08 gt and repeat the same operations Note to deactivate a set slot go to the slot ex 1501 and hold V gt for 3 seconds 10 3 Pool cover mode pons gt Enter the main menu and go to PA 03 menu gt Select On gt to activate the function or OFF gt to deactivate then pres
10. ltration pump by replacing your traditional pump timer but also to control your treatment equipment Its main function is to modulate automatically the daily time of filtration according to water temperature and desired time slots The below mentioned diagram shows the filtration cycles over 24 hours according to the water temperature spitted in 3 slots Slot 1 night slot 2 morning and slot 2 afternoon Go ROP RO EST S ja af Pat fk j ta 16h 18h _ el Jae 2 5 6 20 22 4 28 30 Plage 1 n Plage 2 LE Plage 3 Complementary functions SIMPLEO also manages all the automatic treatment systems in particular the chlorinators to which it brings additional functionalities Y Pool cover mode refer to p 11 SIMPLEO is connected to the pool cover controller and then allows modulating the disinfectant production according to the cover position open or closed in order to avoid over chlorination risks v Indoor pool mode refer to p 11 SIMPLEO includes a mode which has been specifically designed for indoor pools This mode allows to reduce the disinfectant production v Boost mode super chlorination on demand refer to p 10 BOOST function allows to set off un continuous filtration for 24 hours in case of a punctual event requiring a high demand of disinfectant high bath
11. s V to confirm gt If On is selected set the type of relay nO gt normaly open or nC gt normaly closed then press V to valid The production rate for closed cover is then displayed gt Adjust the production rate you wish when cover is closed 25 by default then press V The value is recorder and the device switch to the main display When pool cover mode is activated it is indicated by a flashing C CoL gge 4 Time setting ALI gt Enter the main menu then go to PA 04 menu gt Adjust the first 2 figures for the hour and press V gt to confirm then adjust the 2 last figures for the minutes and press V to valid The device then switches to the main display Mi 5 Indoor pool mode Hri gt Enter the main menu and go to PA 05 menu gt Select On to activate the mode or OFF gt to deactivate then press V gt to confirm gt If On is selected the indoor pool mode is activated and the filtration time will be reduced of 60 6 Flow safety option PAO gt Enter the main menu and go to PA 06 menu gt Select On to activate the mode or OFF gt to deactivate then press V gt to confirm gt If On gt is selected the no flow safety is activated The flow safety activation is indicated by a flashing F 7 Temperature safety recommended for saltwater chlorinators only mym y q gt Enter the main menu and go to PA 07 menu
12. s apo py abeyd aun p C0 sd UONEINUUE Buoy A o 03 sapu y sanay anay ap FOS d nuy GC 7 UWS pedap g abed SO SL 140 yuo i ae SE yenol apop EO Td 110 SSO SUSE Mi anb ye wone SBE so Ts Wa WAU Ol puo ap apow np xoga Y U anay UE snua sap Jos pedap Uga ppo LW aun Jaudy abed dal ya es IPO Sur Ipi BA LO SL uoe e ap abe yy 4 SUR U EMNDE So SUBD JO IA fo ad SWaWRed UN Ja pipo py anua Sa SUBD SS SUED SIO BI Sanal aimes dus 130 t UO 00 apa py Oly Bud A LO d ELA aHeysye 1 41 Ya 11112 11 JAH 4507 1d 19 1934 FUNCTIONS SETTINGS To access the menus v Go to main menu by pressing 3 seconds V v Select the code of a parameter you wish to modify PAO1 to PAO9 using the arrow A Confirm with V v To cancel the modification of a parameter or to leave a menu press quickly 1 Boost mode P HI gt to main menu by pressing 3 seconds V PA O1 menu flashes gt Select ON or OFF then confirm with V gt If ON is selected boost mode is activated and the filtration will run for 24h Boost mode in progress is indicated by a flashing b gt clignc CBSbE IB H Note to stop boost mode just press C 2 Filtration control P AL g Intel
13. the pump but before any other equipment filter gt Place the flow sensor with sensor outpout towards the top gt Connect the flow sensor to terminals 16 and 17 of SIMPLEO V MAINTENANCE A DESCRIPTION 1 Main display Operation mode indicator Auto temperature or manual Alternative display of setting mperature and tim temperature a d time Manu manual oneration Operating light for automatic treatment Operating light for pump SIMPLEO froot techovocie Correction menu exit Menu browsin g parameters kev modification key Validation menu access kev 2 Operating mode v SIMPLEO can operate in 3 modes gt AUTO automatic control of the filtration According to the temperature refer to TEMP p 10 By manual setting refer to TIME p 10 gt MANU manual operation gt OFF filtration stop v To modify the operating mode from the main dispaly temperature hour use the arrow A v The mode in progress is shown by the indicator at the right of the display A M O Ex mode AUTO 32 C Ex mode MANU 28 Ex mode OFF B SETTING MENU ada aa nfa 89 497 S29 130 7 UG anyad way nade g at anduwa abeysnty amas JOSIP JIqep op Td Ja 29997 EI 1207 Un l GSH anjuadway anaes mu 407 d HAL JOTI ADCO 140 Uo Jae CI td AL JUTE 0121 Pe yap ap naes uada JUSTO OAL 8 wou 313 SO vd 140 i UG C anaua ado
Download Pdf Manuals
Related Search