Operation Manual - Whaley Food Service
Contents
1. SUA Lh J tJ USER MANUAL OWNERS MANUAL SCTF Series Countertop Freezers General Instructions Carefully examine the cabinet for shipping damage before discarding the packing material If damage is found contact the delivery carrier immediately and have their agent prepare an inspection report for the purpose of registering a claim THIS IS YOUR RESPONSIBILITY Positioning The cabinet should be positioned on a firm flat base and must not be exposed to direct heat from radiators sunlight or other sources of heat The cabinet emits heat while it is running and this heat is expelled through the black grating at the back of the cabinet Consequently there must be a gap of at least 4 behind the cabinet If the cabinet is placed in a recess placed beneath a working surface etc there must be a gap of at least 4 behind and above the cabinet The cabinet must not be placed on the floor Use Before using the appliance it should be cleaned A weak solution of soapy water is recommended Scouring powder must never be used Temperature setting is the only operation needed The temperature can be adjusted by using the thermostat button at the back of the cabinet Place a thermometer approximately 4 inside the cabinet on the top shelf and check the temperature once it h2. Has the main switch been switched on Is the plug inserted correctly in the outlet Is the thermostat button set correctly oe a A Other Problems Compressor not running Has it been switched off at the main current Has the circuit or fuse blown Is the outlet switched on Is the plug properly in place Is the thermostat correctly adjusted Is the frost layer too thick Thermostat can be adjusted to a lower temperature using the instructions in section Use Temperature too high Is the thermostat correctly adjusted Is there ample air circulation around the unit Is the ambient temperature too warm Thermostat can be adjusted to a lower temperature using the instructions in section Use Compressor not running If you have checked the above points and the appliance is still not working satisfactorily please contact your authorized service agent Light Replacement Disconnect the unit before removing and replacing the inside light Do Not Drill Holes in Cabinet Refrigeration tubing and wiring is routed through the cabinet walls Leaks wet insulatin or electrical problems caused by drilled holes are not covered by warranty Disposal It is the responsibility of the owner of the appliance to ensure that the disposal of the appliance is carried out in accordance with safety and environmental requirements Doors should be removed and together with any locking device be disposed of separately from the appliance The refr
3. number 5 on the thermostat button opposite the hole in the plate Place a thermometer approximately 4 inside the cabinet on the top shelf and check the temperature once it has achieved steady conditions Turn the thermostat button clockwise if the temperature is too high or counterclockwise if the temperature is too low Switching On Before switching on the cabinet should be cleaned Use normal water soluble agents suitable for internal cleaning purposes Once the cabinet has reached the required temperature it is ready for use Do not place product further forward than the front edge of the shelves If you want to keep the light on please turn on the light switch Maintenance A layer of frost gradually forms inside the cabinet When the frost layer is 1 8 deep it should be scraped off using a plastic or wooden scraping implement and removed from the cabinet without switching off The cabinet is then ready for use again If the cabinet is dirty inside it should be switched off and unplugged so the layer of frost can melt before cleaning commences Breakdown If the current supply to the cabinet has been disconnected it should not be reconnected until 6 minutes have elapsed Unless the delay is observed the compressor will not be able to start The cabinet has been thoroughly tested prior to shipment however if breakdowns occur please check the following points first Is the main current disconnected Has the circuit or fuse blown
4. as reach a stable level Turn the thermostat button clockwise if the temperature is too high or counterclockwise if the temperature is too low This equipment is intended for the storage and display of non potentially hazardous packaged ice cream and packaged frozen food Electrical Requirements The power supply to the cabinet must conform to all national and local electrical codes A separate circuit is recommended for each cabinet to prevent loss of product if another appliance on the same circuit causes supply failure NOTE The supply voltage must not vary more than 10 from that shown on the data plate located on the back side of the cabinet If there is any doubt contact an authorized electrician Warning Before removing the plate to the compressor compartment switch off the appliance and remove the plug from the outlet In the interest of safety the appliance should only be serviced by authorized persons The manufacturer will not accept responsibility for any injuries or damage sustained due to unauthorized service or alterations to the appliance WARNING Closed containers with fluids containing carbon dioxide must not be put into the freezer as they may explode Popsicle must not be consumed immediately after they are taken out as they may injure the lips Operation Temperature setting is the only operation needed The temperature can be adjusted by using the thermostat button at the back of the cabinet Start by positioning to
5. igeration system should be removed by an authorized refrigeration service Components including refrigerant and compressor oil should be sent to a recycling center The equipment is intended for use in an area where the environmental conditions are controlled and maintained so that the ambient temperature typically does not exceed 80 F
Download Pdf Manuals
Related Search