Victory - Techni-Lux
Contents
1. reset Whenever necessary perhaps due to an imperfect electric line reset the Victory logic which may feel the effects of interference on the network when very powerful from the controller driving the projec tor This may be done thanks to the remote reset first of all activating it on the logic circuit CS0208 from the relevant dip switch Then it can be used according to the following table 50 234 Lamp histeresis 2353255 Reset ED Cio CD CF E mme SIGIM page 13 SIGM LIGHT TECHNOLOGY Via Pio La Torre 1 61010 TAVULLIA PS ITALY e Tel 0721476477 Fax 0721476170 info sgm it e www sgm it cod M0010902. 81 100 Gobo 4 1075020 Gobo 5 121 140 Gobo 6 141 160 Gobo 7 161 177 Rotagobo speed 1 178 194 Rotagobo speed 2 195 212 Rotagobo speed 3 2137229 Rotagobo speed 4 2307255 Music Hard change gobo channel 4 the operator may select gobo change with blackout values 186 198 or slow gobo change values 225 237 shutter strobe The shutter strobe is adjustable from Channel 4 Shutter Strobe L O20 Shutter closed Use of Music Flash is recommended 1019 see table which gives a remarkable visual 20 29 Stobe 1 39 fps Impact Channel 4 interacts with channel 2 and dee channel 3 values 186 237 40 49 Strobe 1 94 fps It can enable colour change and or gobo 50 59 Strobe 2 34 fps change with blackout as well as analog 60 69 Strobe 2 78 fps gobo change slow 70 79 Strobe 3 29 fps 80 89 Strobe 3 91 fps 90 99 Strobe 4 56 fps 100 109 Strobe 5 45 fps 110 119 Strobe 5 98 fps 120 129 Strobe 6 98 fps 130 139 Strobe 7 85 fps 140 149 Strobe 9 fps 150 159 Shutter Sync audio low freq 160 172 Flash Sync audio low freq 17324185 Flash Sync audio high freq 186 198 Shutter open amp auto shade gobos 199 211 Shutter open amp auto shade colours 212 224 Shutter open amp auto shade gobos colours 225 237 Shutter open low speed gobo change 238 255 Shutter open
3. supply card CS 0207 and a logic card CS 0208 By means of dip switches to address the control channels of the projector and to set the selectable options PAN TILT scanning inversion 8 or 16 bit mirror movement resolution Control mode Remote from remote control or Auto for automatic functioning independent of the projector 5 a micro stepper motors 5 DC motors Digital serial signal DMX512 or RS232 423 ch1 dimmer ch2 colour ch3 gobos ch4 shutter strobe ch5 pan ch6 tilt ch7 gobo rotation ch8 palette ch9 prism and prism rotation ch10 reset ch11 pan 16bit ch 12 tilt 16bit Mirror rotation by means of 2 extra high precision micro stepper motors and controlled by the relevant control card Option to invert mirror scanning The Victorys are in conformity with current CE regulations IP20 degree of protection Automatic power cut off in case of overheating or cooling system operation failure Forced through 1 axial fan In die cast extruded aluminium Epoxy powder enamelling In epoxy powder enamelled steel Installation position with adjustable inclination over 110 cm 18 x 65 x 35 Weight Kg 13 5 SGM Elettronica reserves the right to make improvements and modifications to its products at any time Always refer the manual to the equipment it pertains to in order to avoid mistakes and straying from the actual functions as illustrated in the manual CEN CID CD CF
4. CE SIGIM page 5 appendice SIGIM page 6 Positioning and Focusing Positioning To position the projector the channels must be set as follows Channel 1 dimmer 100 open Channel 2 colour white Channel 3 gobos no figure Channel 4 shutter strobe open Channel 5 6 pan tilt centre position Position the projector rotating it on its support bracket then lock it in the desired position with the knobs Focus adjustment To adjust the lens the channels must be set as follows Channel 1 dimmer 100 open Channel 2 colour white Channel 3 gobos position on a figure Channel 4 shutter strobe open Channel 5 6 pan tilt in position on the point where focus is desired Focusing the Victorys is very easy fast and with absolute precision through the screw knob located on the front of the projector Focus Focusing is accurate on all the gobos as they are all arranged on the same wheel Victory 250 Maintenance Access fo inside Victory has a particular way of access to the inside of the projector Remaining fixed as installed the projector can be opened exactly halfway in longitudinal direction thus allowing easy access to the inner parts in order to carry out any necessary op
5. SIGIM LIGHT TECHNOLOGY R C ro b d J a z T e V t PAS ictory automated luminaire rel 1 02 user manual General warnings Carefully read the warnings contained in this manual since they supply important instructions concer ning safety of installation use and maintenance It is very important that this manual be kept with the equipment for future consultation In case of sale or transfer of the equipment to another user ensure that this manual always accompanies the equipment to allow the new owner to obtain information about the operation and the relevant warnings Not for residential use After unpacking check the integrity of the equipment In case of doubt do not use the equipment and contact an authorized SGM Technical Service Centre The packaging materials plastic bags expanded polystyrene nails etc must be kept out of reach of children since they are potential sources of danger This equipment may only be operated by adults Do not allow children to tamper with the machine or play with the product The electrical and mechanical work necessary for the installation of the equipment must be carried out by a qualified electrician or by a competent person Before connecting the unit check that the data on the registration plate is the same as that of the electrical grid Avoid using the equipment in places subject to excessive humidity in places subject to vibrations or knocks in p
6. ave allowed obtaining a movement capability which is ultrafast precise and very linear even at lower speeds Moreover the Victorys accept 16 bit control which ensures a linearity of movement unbeatable among the projectors in this range Mirror scanning can also be inverted to facilitate installation and programming Strobe The stroboscopic effect of the Victorys is extremely fast for a projector of this category and may be adjusted by the operator to a frequency from 1 to 9 flashes a second Dimmer The Victorys are also fitted with a dimmer function so that the light intensity may be dimmed from 0 to 10096 ED Cio D CF CE mme SIGIM page 3 SIGIM page 4 e Iris The Victorys do not have a mechanical iris but the 8 position gobo wheel has a position to shape the luminous beam thus obtaining a narrower beam which for example can be directed at a mirrored globe or used to satisfy any other special need Since the gobo is interchangeable the amplitude of the luminous beam may be selected from the many available ShuHer A shutter is available on the Victorys which may be activated instantaneously to block the luminous beam output Colour 8 base colours are available on Victory 7 white obtained through top quality They are all easily inter changeable so that also personal requirements can be satisfied The colours may be selected as follows e fixed positions full colour e intermediate positions for two colour bea
7. ave properly hooked the lower part to prevent it from suddenly drop ping downwards Projector cleaning Periodic checks Cleaning the optics internally and externally is determining for maximum lumi nous yield and should periodically be carried out The cleaning frequency above all depends on the place where the projector operates In particular a humid environment with a great deal of smoke or dust favours greater accumulation of dirt on the projector optics Clean with a soft cloth using normal window cleaning products or denatured alcohol always carefully drying the parts Clean the external optics at least every 15 20 days and the internal optical unit condenser lenses parabola and gobo unit ED Cio D CF CE mme SIGIM page 7 SIGIM page 8 including the rotation system at least every 40 60 days To ensure an always perfectly efficient projector a general overall inspection every 700 hours of opera tion is recommended Checking of the electrical and mechanical parts must be carried out by technical staff Colour replacement Open the projector after disconnecting it from the mains If it was on wait for the lamp and the internal mechanical parts to cool down about 30 minutes The colour wheel consists of two parts between which the seats of the colour filters are located To replace them with the finger very gently separate the two locking discs at the point of the dichroic filter to be replaced Remove the fi
8. dic checks Colour replacement Gobo replacement Start addresses Victory connections Options Dip switch Pan Tilt Normal Reverse Mirror 8 16 bit res Auto Remote mode Control channels ch 1 dimmer ch 2 colour ch 3 gobo ch 4 shutter strobe ch 7 reset SIGM LIGHT TECHNOLOGY Made in Italy by SGM Electronic Printed in September 1998 Rel 1 02 Main Characteristics The intelligent projectors of the Victory series spring from a design philosophy which all SGM products have for years had in common These new scanners because of their avant garde performance cer tainly take top place among the best in world wide production The accurate study of the functions the search for innovative materials the continuous technical updating have led to the realization of a certainly unique product Victorys are projectors suitable for a multitude of applications The vast and pluridecennial experience of SGM in the sector of light control systems has allowed developing a product with high reliability and precision of which the mechanics optics and electronics are entirely designed by our own research laboratories This allows absolute mastery of the know how and optimisation of the quality price relation As every SGM product before commercialisation the Victorys have brilliantly passed the long testing period and the strict tests they have had to undergo this is synonymous with high quality and reliabi lity The particular care o
9. eration be it cleaning lamp change or service of any mechanical or electrical part To open the projector unscrew the 2 knobs on the front Fig 1 taking care that the lower part does not drop downwards suddenly when the screws are undone A locking lever Fig 3 will automatically hold it open at maximum travel fig 3 fig 2 d Lamp mounting or replacement WARNING Before replacing the lamp Evaluate the effective necessity to replace the lamp average lamp life about 300 h Disconnect the projector from the mains If the projector was on before opening it wait for the lamp and the internal mechanical parts to cool down 10 30 minutes Remove the burnt out lamp Be extremely careful not to touch the optics the parabola and the lamp with bare hands since the residuals subjected to high tem peratures burn causing the parts to blacken and irreparably damaging the lamp Proceed with mounting the new lamp placing it carefully in its housing FOR GOOD PROJECTION IT IS VERY IMPORTANT THAT THE LAMP FITS PER FECTLY IN THE SOCKET After each lamp replacement it is recommended to carry out a complete cleaning cycle After carrying out the necessary operations before pushing the lower part towards the top Fig 2 to close the projector release the locking lever lifting it towards the top Fig 3 Screw down the 2 knobs one after the other taking care that these h
10. ight or top bottom the Victorys will have opposite movements Therefore to make mirror scanning uniform act on PAN MOVE TILT MOVE of one of these OPTIONS 1 23 4 TILT normal reverse _ PAN normal reverse MIRROR res 8 16 bit MODE auto remote TILT normal reverse PANT normal reverse MIRROR res 8 16 bit MODE auto remote CENTER POINT AREA 77 TILT 50 x PAN 50 x TILT 100 x PAN 100 x Max AREA DI LAVORO OPTIONS TILT normal reverse _ PAN normal reverse MIRROR res 8 16 bit MODE auto remote PAN normal reverse MIRROR res 8 16 bit MODE auto remote TILT 100 x PAN 100 x TILT normal reverse zl TILT normal reverse PAN normal reverse MIRROR res 8 16 bit MODE auto remote OPTIONS TILT 0 PAN 0 CENTER POINT AREA cm TILT 50x PAN 50 x 1 Max AREA DI LAVORO Gei TILT 100 x TILT 100 x L PAN 100 x PAN CENTER POINT AREA 7 TILT 50x PAN 50 x Max AREA DI LAVORO Mirror res 8 16 bit The Victorys may also be 16 bit controlled on PAN TILT This function which normally is coupled to more professional projec tors guarantees absolute linearity of movement To activate this function the OPTIONS dip switch 3 must be set to ON In order to use the 16 bit control the Victorys need 2 additional control channels therefore passing from 7 to 9 channels Auto remote mode The Victorys can also function autonomously without the c
11. ion For connection in a DMX network always use balanced microphonic cables type RF 60 12 2x0 2bmm or similar and select a good quality to prevent malfunctioning of the projector To reduce interference it may be necessary to insert a network terminator on the last projector in the DMX chain realized with a 1200 1 4W resistor placed between pins 2 and 3 of the DMX connector Warning The screening part of the cable braid must NEVER be connected to the system earth since this would lead to malfunctioning of the projector and the control units DMX512 or RS 232 line socket pin out RS 232 423 connection input DIGITAL SIGNAL RS 232 COMPUTER OUT output 25 PIN CONNECTOR RS 232 CEN CID CD CFD CE appendice VICTORY 5 PIN CONNECTOR SIGIM page 9 GIMI page 10 OPTIONS Dip switches PAN TILT Normal Reverse OPTIONS The PAN and TILT dip switches are used to invert vertical and hori 1234 zontal scanning from top to bottom from left to right and vice Wd ON versa T Ex In the case where two Victorys are installed one in front of the other moving the joystick to the left r
12. laces with temperatures higher than 45 C or lower than 2 C Protect the equipment from excessively humid conditions the optimum values are between 35 and 80 Do not disassemble or modify the equipment Prevent inflammable liquids water or metallic objects from penetrating the equipment In case of spilling liquid on the equipment immediately disconnect the power supply of the mixer The minimum distance between the projector and the surface to be illuminated must not be less than 1 5 m In case of serious functioning problems switch off the equipment and contact the nearest SGM retailer or the manufacturer directly for inspection Avoid opening the equipment there are no parts repairable by the user Never try to repair the equipment alone Repairs carried out by inexpert persons may cause damage or serious malfunctioning Contact the nearest authorised Technical Service Centre Always insist on original spare parts Protect the environment do not throw the packaging in your dustbin but return it to your retailer or take it to a collection point for special waste disposal ED Cio DD CF CE mme SIGIM page 1 SIGIM page 2 Index General warnings Index Main characteristics Lamp Optic system Focusing Mirror Strobe Dimmer Iris Shutter Colour Gobo Technical characteristics Positioning and focusing Positioning Focus adjustment Victory 250 maintenance Access to inside Lamp mounting and replacement Cleaning Perio
13. lter and insert the new one Properly close the wheel and the projector Gobo replacement Open the projector after disconnecting it from the mains If it was on wait for the lamp and the internal mechanical parts to cool down about 30 minutes With the aid of a small screwdriver remove the spring C replace the gobo B reinsert the spring taking care to insert it perfectly on the special gobo ring A Properly close the projector Start Addresses For connection in DMX512 mode each projector must appropriately be configured The start address is set with the dip switch located on the back of the projector The address can be modified also when the projector is on 1 2 4 8 16 32 64 128 256 Victory II PRO150 1 ch 01 12 Victory II PRO150 2 ch 13 25 Victory II PRO150 3 ch 26 38 Victory II PRO150 4 ch 39 51 1 E BH iN 2 no Bo dies M 4 w CE 4 CR 8 B CH eg 16 W _ o OT 16 ff EDIT lo EDIT 19 IE M GAR GAR GAR 128 co 123 85 1 256 o 2560 M lt 2560 Warning Always refer to the numbers silk screen printed on the Victory panel and not to those on the dip switch Victory Connections The projector is fitted with a DMX512 and RS 232 423 input output When making the start address settings consider that 4 channels are used channel 1 is not operatio nal in this vers
14. ms e variable speed rotation to obtain a spectacular rainbow effect e passage from one colour to another with or without blackout e synchronization of the colour change with the music on fixed positions Music Hard The passage between the different colours is imperceptible to the human eye as it is extremely fast the absolute fastest among the projectors in this range and occurs in 0 08 sec Gobos The Victory gobo unit consists of a single wheel with 7 images and one empty position All the gobos are easily interchangeable so that the operator may install new figures easily and quickly The gobo change occurs in fast imperceptible mode or in analog mode with a slow passage from one figure to the next Technical Characteristics Power supply Lamp Absorbed power Optic unit Optic system Lenses Mirror Electronics Settings Motors Input Control channels Mirror movement Safety regulations Safety devices Cooling system Body Mounting bracket Dimensions 90 260V 50 60Hz Universal automatic voltage change 250W 24V EVC M 33 G6 35 connector Life approx 300 hours 300 W Mirrored parabola with very high luminous yield designed for Victory Mirrored parabola 7Omme lens 90mmoe lens screw focusing In glass with high transmission coefficient Ultra high reflection in special glass Entirely developed by engineers of the SGM Research amp Development Laboratory Has a power
15. ontrol auxiliary To activate this function the OPTIONS dip switch 4 must be set to OFF The projector will start running 8 resident programs AUTO in a continuous cycle 100 x TILT 50x PAN 50 x Max AREA DI LAVORO OPTIONS TILT normal reverse PAN normal reverse MIRROR res 8 16 bit MODE auto remote TILT normal reverse PAN normal reverse MIRROR res 8 16 bit MODE auto remote Control channels EE ee Adjustable from channel 1 allows linear adjustment of the light intensity from 0 to 100 according to operator requirements EP On Victory the 8 base colours are multiplied by a colour temperature conversion filter thus obtaining 16 colours The top quality 38 dichroic filters are carefully selected to guarantee perfect colour uniformity They are all easily interchangeable so that also personal requirements can be satisfied The colours may be selected as follows e fixed positions full colour e intermediate positions for two colour beams e variable speed rotation to obtain a spectacular rainbow effect e passage from one colour to another with or without blackout e synchronization of the colour change with the music on fixed positions Music Hard The passage between the different colours is imperceptible to the human eye as it is extremely fast the absolute fastest among the projectors in this range and occurs in 0 08 sec To activate change with blackout channel 4 shutte
16. r must be set to a value of between 199 and 211 White White Yellow Yellow Yellow Magenta Magenta Magenta Cyan Cyan Cyan Orange Orange 100 109 Orange Green Green 110 119 Green Blue 120 129 Blue 1905139 Blue Red 140 149 Red 150 159 Red White 160 170 Rainbow speed 1 100190 Rainbow speed 2 181 191 Rainbow speed 3 192 201 Rainbow speed 4 20221 Rainbow speed 5 LAS 005 Rainbow speed 6 224 233 Rainbow speed 7 234 244 Rainbow speed 8 245 255 Music hard change ED Cio D CF CE mme SIGIM page 11 SIGIM page 12 EP The gobo wheel is adjustable from Channel 3 All the gobos are easily interchangeable the light filter diameter is 34 mm The gobo selection is controlled by optical sensors located near the wheel The Victory gobo unit consists of only one wheel with 7 ima ges and one empty position All the gobos are easily interchangeable so that the ope rator may install new figures easily and quickly The gobo change occurs in fast impercepti ble mode or in analog mode with a slow passage from one figure to the next Selecting the rotagobo function running of figure adjustable to 4 preset speeds allows obtaining a special visual effect Channel 3 interacts with channel 4 From 41 60 Gobo 2 61 80 Gobo 3
17. ver the aesthetics and the optimisation of the outer structure aimed at functiona lity allow easy installation in any position and extremely fast technical intervention The Victorys are constructed in conformity with the CE regulations currently in force Lamp The Victorys use an extra low voltage incandescent halogen lamp with a 2 pin connector without doubt the ideal lamp for this type of projector since it combines good reliability with long life about 300 hours It has surprising luminous power at ridiculously low cost absolutely incomparable with other metallic iodide lamps mounted on projectors of the same type e Optic system The special SGM designed parabola able to concentrate the luminous beam and the condenser lens in selected glass with a high transmission coefficient subjected to special multilayer antireflection treat ment exalt the brilliance and luminous power of the Victorys whose brightness is positively astoun ding Focusing Focusing the Victorys is extremely easy fast and with absolute precision from the screw panel located on the front of the projector Focus Focusing is accurate on all the gobos as they are all arranged on the same wheel Mirror The mobile mirror of the Victorys has ultra high reflection able to reduce the loss of luminous yield to a minimum The scanning time is 0 5 seconds for the 90 Pan and 0 3 seconds for the 180 Tilt Extremely elaborate software and the use of first class motors h
Download Pdf Manuals
Related Search