Aimpoint T1 Engineering Paper (2 Page)
Contents
1. Dot Brightness Power Source Battery Type One 3 V lithium Battery type CR2032 commercially available Over 5 years of continuous day and night use at pos 8 of 12 and over 10 months at pos 10 of 12 Typically 500 000 h at NVD setting Storage battery 10 years Battery Life typical MOA Minute Of Angle 1MOA 30 mm at 100 m or 1 at 100 yards 2NVD Night Vision Device Values valid at room temperature and for a quality battery Physical Specifications Dimensions LxWxH 62 mm x 41 mm x 36 mm 2 4 x 1 6 x 1 4 Sight only 62 mm x 41 mm x 40 mm 2 4 x 1 6 x 1 6 Sight with Mount 18 mm 0 7 over top surface of Picatinny Rail Weight 84 grams 3 0 oz Sight only 105 grams 3 7 oz Sight with Mount Lens Covers will add 7 mm 0 3 to the length and 10 grams 0 4 oz to the weight Range 1 m at 100 meters 1 yds at 100 yds in windage and elevation 1 click 10 mm at 80 meters 13 mm at 100 meters 1 2 at 100 yds Extruded high strength aluminum hard anodized black to dark gray non glare finish Material Lens Covers Rubber black non glare finish Radioactive Materials None Tritium 0 Thorium 0 Thorium Fluoride 0 None Mercury 0 including battery Keyed mount Maintainability Height of optical axis Mean Time To Repair Lens Covers Adjustment Material Housing Hazardous Materials Environmental Specifications Temperature Range Operating and St2. Ensure that Battery Cap 2 and the two Adjustment Caps 1 are tightened before exposing the Sight to sea spray mud snow or before immersing the sight in water Tighten the 2 Adjustment Caps 1 by hand and use the Tool 9B to tighten the Battery Cap 2 Keep Lens Covers 8 closed when sight is not being used Clean lenses with lens paper cloth and wipe the sight dry as soon as possible after exposure to water sea spray mud or snow Dust storms and sand storms Keep Lens Covers 8 closed when sight is not being used f High altitudes No special procedures required CAUTION The lenses shall never be cleaned with fingers but with lens paper cloth If no lens paper cloth available To clear away debris sand grass etc blow away the dirt To clean lenses mist up the lenses and clean them with a soft piece of cloth c d e CHAPTER IV TROUBLE SHOOTING PROCEDURES 4 1 RED DOT DOES NOT APPEAR Discharged Battery Replace Battery Battery installed incorrectly Remove and reinstall Battery with toward Cap Battery is not making good contact Clean contact surfaces and reinstall Battery Defective Rotary Switch Notify dealer armourer The Battery Cap is not enough tightened Tighten the Battery Cap so that it gets in contact with the bottom of the Battery Housing 4 2 IMPOSSIBLE TO ZERO Adjustment screw is at its limit Check alignment of Mount to Barrel Check Mount and Weapon Rail or Carry Handle
3. stability Impact point is moving CHAPTER V MAINTENANCE a This reflex sight does not require any particular maintenance while used under normal conditions b Under severe weather conditions please refer to chapter III c Keep lens covers closed whenever the sight is not in use d Warehouse storage Remove battery and allow lens surfaces to dry completely if wet before closing the lens covers e To clean lenses refer to CAUTION in CHAPTER III f To reach maximum protection level for all weather conditions wax is added into the rubber mixture The wax will slowly migrate to the surface of the part During frequent use this wax will be used up completely and not noticed by the user For long time storage the wax will not be used up as frequently and will be seen as a grey film on the surface To restore to its original condition please hand wash in warm dishwater IMPORTANT INSTALLATION INSTRUCTIONS To avoid damage to the sights and for the proper assembly of the mount on the sight shall the small original screws M3x4 only be tightened by Aimpoint Operator s and Maintenance Manual for AIMPOINT MICRO T 1 CAUTION Do not continue to adjust windage and elevation mechanisms hand and with the attached micro tool if you encounter resistance ang Ang WIU NG ened MICTON00 Aimpoint AB Aimpoint Inc T this agershi i The Elevation Adjustment Screw 5 is located on top of the sight while o do Jagershillgatan 15 14
4. 103 Mariah Court i s pou SE 213 75 Malm Sweden Chantilly VA 20151 2113 USA the Windage Adjustment Screw 5 is located on the right side Phone 46 0 40 671 50 20 Phone 1 703 263 9795 a Open remove Lens Covers 8 Fax 46 0 40 21 92 38 Fax 1 703 263 9463 b Turn the Rotary Switch 4 clockwise until the red dot has a sufficient 1 Turn the sight upside down Hold it in your hand with the screw holes up 2 Press the mount against the sight and check that there is no gap 3 Apply locking compound to the threads and install the screw in the mount e mail info aimpoint se e mail info aimpoint com intensity to contrast against the target www aimpoint com c Remove the Adjustment Cap 1 for windage and elevation adjustment one at a time Either the two knobs incorporated on top of the Adjustment Cap 1 or the Tool 9A shall be used for adjusting the Adjustment Screw 5 Reverse the Adjustment Cap 1 and the knobs will fit into the two recesses on the Adjustment Screw 5 WARNING Do not overtighten 4 Mount the Screws crosswise Tighten each Screw until resistance is felt Rotate the Bolt Head an additional 1 4 turn to fully tightened This is equivalent to 1 0Nm 0 2Nm of torque www aimpoint com THE FUTURE IN SIGHT Copyright 2014 Contents property of Aimpoint All rights reserved 12034 4
5. CHAPTER 1 1 PRESENTATION Aimpoint Micro T 1 Reflex Sight is a small light and rugged red dot sight developed mainly for military and law enforcement applications Aimpoint red dot sights are designed for the two eyes open method of sighting which greatly enhances situational awareness and target acquisition speed Thanks to the parallax free design the dot follows the movement of the user s eye while remaining fixed on the target eliminating any need for centering Further the Micro T 1 allows for unlimited eye relief and is compatible with 1st 2nd and 3rd generation night vision devices The Aimpoint Micro T 1 uses the Advanced Circuit Efficiency Technology called ACET which combines Aimpoint s superior accuracy and ease of use with significantly lower power usage With the Micro T 1 sight Aimpoint has introduced an aiming system that gives the performance of our full sized sights in the smallest package possible 1 2 SPECIFICATIONS Optical System Operating Principle Passive Red Dot Collimator Reflex Sight Optical Magnification 1 x unlimited eye relief Clear Aperture 20 mm Aiming Dot Size 2 MOA 0 6 mRad or 4 MOA 1 2 mRad Optical Coating Anti reflex and Band Pass coatings NVD compatible 12 settings 4 NVD and 8 Daylight settings of which 1 Extra Bright Dot brightness manually adjusted Dot Color Red 650 nm wavelength Optical Signature No forward optical signature from the dot beyond 10 meters
6. justments are necessary providing that the weapon rail Picatinny Rail is properly aligned NOTE Each click of the Adjustment Screw 5 corresponds to a 13 mm movement of the point of impact at 100 meters 3 mm at 25 meters and 26 mm at 200 meters or 1 2 at 100 yds d Insert either the two knobs on top of the Adjustment Cap 1 or the two knobs on the Tool 9A in the two holes on the Adjustment Screw 5 and turn as follows To move the point of impact to the right turn windage adjustment screw counter clockwise To move the point of impact to the left turn windage adjustment screw clockwise To move the point of impact up turn elevation adjustment screw counter clockwise To move the point of impact down turn elevation adjustment screw clockwise e Confirm zeroing by firing at least three shots at a zeroing target Check points of impact on zeroing target to confirm accuracy and repeat above procedure if required f After initial firing ensure that the sight is secure g Turn Rotary Switch 4 to position 0 counter clockwise h Close front and rear Lens Covers 8 CHAPTER III OPERATION UNDER EXTREME CONDITIONS a Extreme heat moist or dry No special procedures required b Extreme cold Extreme cold might shorten battery life It could also make the Rotary Switch 4 a little harder to turn than at normal temperatures Salt air No special procedures required Sea spray water mud and snow
7. n the weapon The Micro Sight is designed for installation on most types of weapons which have a MIL STD 1913 Picatinny Rail or Weaver Rail If your weapon does not have or support an appropriate base s please consult your dealer gunsmith or other qualified source 2 1 2 1 Installing Sight on a Picatinny Rail a Loosen the Shaft 10 by means of the Tool 9C so that the Locking Bar 11 can clamp around the Picatinny Rail b Install the Sight to the weapon Rail by tightening the Shaft 10 First ensure that the Sight is correctly positioned and that the Shaft 10 recoil stop fits into a groove on the Picatinny Rail To make sure that the Shaft is firmly tightened screw the Shaft 10 clockwise until a light resistance can be encountered After that screw another 1 4 to 1 2 turn WARNING Do not overtighten c When using Lens Covers 8 ensure that they are correctly positioned and can easily be opened d Finally make sure that the Shaft 10 with Locking Bar 11 is firmly tightened around the weapon Rail e Complete zeroing according to 2 2 1 below 2 1 3 Lens Covers In order to preclude the loss of the lens covers when removed from the optical path of the Sight the lens covers should be removed downwards The rubber string will then grab around the Sight and Base 2 2 OPERATING PROCEDURES 2 2 1 Zeroing The Micro Sight is delivered with the red dot in a centered position Normally this means that only small ad
8. orage 45 C to 71 C 50 F to 160 F Water Resistance Fully waterproof Chemical Resistance Not affected by weapons cleaners lubricants oil or insect repellants Mechanical Interface Mount for MIL STD 1913 Rail System Picatinny Rail included for T 1 Less than 0 5 h at field level MTTR 1 3 LOCATION AND DESCRIPTION OF MAJOR COMPONENTS See figure OORwWnr Adjustment Cap 2 pcs Battery Cap Battery type CR2032 Rotary Switch Adjustment Screw Base 7 Screws 4 pcs for Base 8 Lens Cover rubber 9 Tool 3 functions 10 Shaft for Base 11 Locking Bar CHAPTER II OPERATION UNDER NORMAL CONDITIONS 2 1 ASSEMBLY AND PREPARATION FOR USE WARNING Insure the weapon is unloaded and the safety selector is in the safe position before attempting to install remove or perform maintenance on the sight 2 1 1 Installing Battery a Remove Battery Cap 2 by turning it counter clockwise b Insert a battery type CR2032 with positive end toward Cap CAUTION Install the battery in the battery compartment carefully Open the Battery Cap 2 Inspect that the current O ring is not damaged Failure to do so could result in water leakage into the battery compartment c Install Battery Cap 2 by turning clockwise until snug Tighten with the provided Tool 9B only d Verify that red dot is present by turning the Rotary Switch 4 clockwise 2 1 2 Installing Sight o
Download Pdf Manuals
Related Search