595 Kb Manual_B12
Contents
1. LIGHTING PROFESSIONAL LED COLOR CHANGER USER MANUAL Bie KEEP THIS MANUAL FOR FUTURE NEEDS Introduction Thank you for using QUADRO B12 This unit is a DMX intelligent LED wash light that can be used as a stand alone or a sound active mode The unit can also be controlled via Wireless DMX QUADRO B12 has been thoroughly tested and has been shipped in perfect operating condition Carefully check the shipping carton for damage that may have occurred during shipping If the carton appears to be damaged carefully inspect your unit for any damage and be sure all accessories necessary to operate the unit has arrived intact In the case damage has been found or parts are missing please contact the manufacturer or your dealer for further instructions Do not return this unit to your dealer without first contacting To optimize the performance of this product please read these operating instructions carefully to familiarize you with the basic operations of this unit These instructions contain important safety information regarding the use and maintenance GENERAL GUIDELINES This device is a lighting effect for professional use on stages in discotheques theatres etc This fixture is only allowed to be operated with the max alternating current which stated in the technical specifications of this manual the device was designed only for indoor use Lighting effects are not designed for permanent operation Consistent2. 10 times the weight for 1 hour without any harming deformation The installation must be secured with a secondary safety attachment an appropriate safety rope Never stand directly below the device when mounting removing or servicing the fixture The operator has to make sure the safety relating and machine technical installations are approved by an expert before taking the device into operation for the first time These installations have to be approved by a skilled person once a year Cautions The effect should be installed outside areas where persons may reach it walk by or be seated Overhead mounting requires extensive experience including amongst others calculating working load limits installation material being used and periodic safety inspection of all installation material and the device If you lack these qualifications do not attempt the installation yourself Improper installation can result in bodily injury CAUTION The electric connection must only be carried out by a qualified electrician Before mounting make sure that the installation area can hold a minimum point load of 10 times the device s weight Warning To prevent or reduce the risk of electrical shock or fire do not expose this unit to rain or moisture Caution There are no user serviceable parts inside this unit Do not attempt any repairs yourself doing so will void your manufactures warranty In the unlikely event your unit may require service pl
3. this unit in an area that will allow proper ventilation Allow about 20cm between this device and a wall Do not attempt to operate this unit if it becomes damaged This unit is intended for indoor use only use of this product outdoors voids all warranties During long periods of non use disconnect the unit s main power Always mount this unit in safe and stable matter Heat The appliance should be situated away from each appliance that produce heat Cleaning The unit should be cleaned only as recommended by the manufacturer See Cleaning for details CAUTION Never touch the device during operation The housing may heat up CAUTION Never look directly into the light source as sensitive persons may suffer an epileptic shock Please be aware that damages caused by manual modifications to the device are not subject to warranty Keep away from children and non professionals INSTALLATION INSTRUCTIONS Mounting the device CAUTION Please consider the EN 60598 2 17 and the other respective national norms during the installation The installation must only be carried out by a qualified person QUADRO B6 can support power supply from 110V to 230V so you need to be sure to connect the machine with the correct voltage The applicable temperature is between 0 C 45 C Do not use the lighting under or above the temperature The installation of the effect has to be built and constructed in a way that it can hold
4. Charging current 14A Maximum capacity 92Ah Maximum output current 14A Standard charge time Shours Discharge cut off voltage 2 75V circulation life 500 times DMX wireless specs Wireless DMX 512 protocol Built in 2 400G 2 525 receiver transmitter for wireless DMX 126 auto jumping channel frequencies high anti jamming ability to ensure work reliability 7 ID codes for multiple transmitters and receiver use Wired DMX 512 protocol Note All information is subject to change without prior notice
5. STRUCTIONS CAUTION Be careful with your operations With a dangerous voltage you can Suffer a dangerous electric shock when touching wires This device has left the factory in perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual gt gt Important Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems This device falls under protection class I Therefore it is essential that the device be earthed Be sure that the local power outlet match that of the required voltage for your unit The electric connection must carry out by qualified person No move at operating mode To reduce the risk of electrical shock or fire do not expose this unit to rain or moisture Do not spill water or other liquids into or on to your unit Do not attempt to operate this unit if the power cord has been frayed or broken Do not attempt to remove or break off the ground prong from the electrical cord Disconnect from main power before making any type of connection Do not remove the cover under any conditions There are no user serviceable parts inside Never operate this unit when its rear cover is removed Never plug this unit in to a dimmer pack without proper ventilation Always be sure to mount
6. d chasing through the built in programs You can choose the sensivity by the knob in the panel Auto Mode The unit will automatically chase through the different colors DMX control mode This function will allow you to control each individual units traits with a standard DMX 512 controller Master slave mode One unit will work as the master in the one of the above three modes other units in the chain will work in synchronization towards the master DMX Mode Operating through a DMX controller give the user the freedom to create their own programs tailored to their own individual needs This function also allows you to use your units as spot lights 1 This function will allow you to control each individual unit s traits with a standard DMX 512 controller 2 The QUADRO B12 uses 7 48 51 DMX channels to operate Please see DMX Values and Functions for the DMX traits 3 To run your unit in DMX mode plug in the unit via the XLR connections to any standard DMX controller Set your desired DMX address following the setup specifications that come with your DMX controller Touch Buttons There four touch buttons under the LCD display Esc Down Up and Enter Normally the LCD will display in the second line of the LCD screen the current DMX address code as like DMX Address 001 When the first line reads Select Menu lt gt press Func to enter the main menu Press Up Down to scroll in the menu or sub
7. ease contact the manufacturer or your dealer Panel Instruction LCD DISPLAY nu E Battery arging AC POWER DMX RoHS m ON ON SOUND Q wii SOUND ADJ orr ESC UP DOWN ENTER C POWER POWER DMX DMX TSE rum IN PUT e OUT PUT IN PUT OUT PUT 3 4 5 Power in and out powerconn connectors 2 Dmx in and out xlr connectors 3 On Off wireless switch 4 Charge Off On Battery selector 5 On Off AC selector Off On with AC On with Battery 3 Off 1 Power plug connected 4 On 4 Off 4 On 5 Off 5 Off 5 On On with dmx cables On with Wireless 2 dmx cables connected 3 On 3 Off Charge 1 Power plug connected 3 Off 4 Charge 5 On Battery Indicator 1 Battery power 10 p 4 Battery eee Charging Chargina Indicator hear 2 Battery power 50 3 Battery power 100 4 Charging led Red color charging Green color full TX RX ID Indicator Steady Red light no dmx signal Flashing Red light dmx signal transmission Flashing Green light dmx signal reception When you have Wireless On you can choose 7 different working groups by the ID button The RX TX ID led will show you different color each press RED GREEN RED GREEN BLUE RED BLUE GREEN BLUE RED GREEN BLUE Machines with same ID will work togheter Operating Instructions You can use QUADRO B12 in 4 ways Sound Active mode The unit will react to soun
8. ion 11 127 Color changing from 3 0 255 slow to fast 128 245 Color fade from slow to fast 246 255 NoFunction 4 0 255 Red dimmer 5 0 255 Green dimmer 6 0 255 Blue dimmer 0 255 White dimmer gt 48 Channels mode Channel Value Function 1 0 255 first dot red dimmer 2 0 255 first dot green dimmer 3 0 255 first dot blue dimmer 4 0 255 first dot white dimmer 5 0 255 second dot red dimmer 6 0 255 second dot green dimmer 7 0 255 second dot blue dimmer 8 0 255 second dot white c dimmer 9 0 255 third dot red dimmer 10 0 255 third dot green dimmer 11 0 255 third dot blue dimmer 12 0 255 third dot white dimmer 13 0 255 fourth dot red dimmer 14 0 255 fourth dot green c dimmer 15 0 255 fourth dot blue dimmer 16 0 255 fourth dot white c dimmer 17 0 255 fifth dot red dimmer 18 0 255 fifth dot green dimmer 19 0 255 fifth dot blue dimmer 20 0 255 fifth dot white dimmer 21 0 255 sixth dot red dimmer 22 0 255 sixth dot green dimmer 23 0 255 sixth dot blue dimmer 24 0 255 sixth dot white dimmer 25 0 255 seventh dot red dimmer 26 0 255 seventh dot green dimmer 27 0 255 seventh dot blue dimmer 28 0 255 seventh dot white dimmer 29 0 255 eighth dot red dimmer 30 0 255 eighth dot green dimmer 31 0 255 eighth dot blue dim
9. menu options Press Enter to confirm your selection and the first line will change to Select Value lt gt At this time press Up Down to change the value in the selected function Any time press and hold Up or Down the value will rapidly change and stop when release Once the value is set press enter again to save and exit to the main menu LCD Operation Menu The brand name will be displayed when the unit is power on After initialization it will show the model name Then the unit is ready for setting and working Please see the following table for setting information Menu Function Sel menu E E ChModeXX Channel Mode 07 48 51 Sel menu um Addr XXX Address Selection 000 255 Seb menu Slave Mode Slave Sel menu Sound Mode Sound Sel menu d Auto Mode Static Colors 00 15 00 off 01 red 02 red green 03 green Sel menu 04 gree blue 05 blue 06 blue white 07 white 08 red white Color XX 09 green white 10 red blue 11 greent blue white 12 red green blue 13 red blue white 14 red green white 15 red green blue white Sel menu ChangXXX Changing Colors 000 255 from slow to fast Sel menu Fade XX Fade 000 015 from slow to fast DMX Values and Functions gt 7 channels mode Channel Value Function 1 0 255 Master dimmer 0 255 0 10 NoStrobe 11 245 Master strobe from slow to fast 246 255 NoStrobe Color Functions 0 10 NoFunct
10. mer 32 0 255 eighth dot white dimmer 33 0 255 ninth dot red dimmer 34 0 255 ninth dot green dimmer 35 0 255 ninth dot blue dimmer 36 0 255 ninth dot white dimmer 37 0 255 tenth dot red dimmer 38 0 255 tenth dot green dimmer 39 0 255 tenth dot blue dimmer 40 0 255 tenth dot white dimmer 41 0 255 eleventh dot red dimmer 42 0 255 eleventh dot green dimmer 43 0 255 eleventh dot blue dimmer 44 0 255 eleventh dot white dimmer 45 0 255 twelfth dot red dimmer 46 0 255 twelfth dot green dimmer 47 0 255 twelfth dot blue dimmer 48 0 255 twelfth dot white dimmer gt 51 Channels mode Channel Value Function 1 0 255 Master dimmer 0 255 0 10 NoStrobe 11 245 Strobe from slow to fast 246 255 NoStrobe Color Functions 0 10 NoFunction 11 127 Color changing from 3 0 255 slow to fast 128 245 Color fade from slow to fast 246 255 NoFunction 4 0 255 first dot red dimmer 5 0 255 first dot green dimmer 6 0 255 first dot blue dimmer 7 0 255 first dot white dimmer 0 255 second dot red dimmer 9 0 255 second dot green dimmer 10 0 255 second dot blue dimmer 11 0 255 second dot white c dimmer 12 0 255 third dot red dimmer 13 0 255 third dot green dimmer 14 0 255 third dot blue dimmer 15 0 255 third dot white dimmer 16 0 255 fourth dot red dimmer 17 0 255 fourth dot green c dimmer 18 0 255 fourth dot blue dimmer 19 0 255 fourth dot white c di
11. mmer 20 0 255 fifth dot red dimmer 21 0 255 fifth dot green dimmer 22 0 255 fifth dot blue dimmer 23 0 255 fifth dot white dimmer 24 0 255 sixth dot red dimmer 25 0 255 sixth dot green dimmer 26 0 255 sixth dot blue dimmer 27 0 255 sixth dot white dimmer 28 0 255 seventh dot red dimmer 29 0 255 seventh dot green dimmer 30 0 255 seventh dot blue dimmer 31 0 255 seventh dot white dimmer 32 0 255 eighth dot red dimmer 33 0 255 eighth dot green dimmer 34 0 255 eighth dot blue dimmer 35 0 255 eighth dot white dimmer 36 0 255 ninth dot red dimmer 37 0 255 ninth dot green dimmer 38 0 255 ninth dot blue dimmer 39 0 255 ninth dot white dimmer 40 0 255 tenth dot red dimmer 41 0 255 tenth dot green dimmer 42 0 255 tenth dot blue dimmer 43 0 255 tenth dot white dimmer 44 0 255 eleventh dot red dimmer 45 0 255 eleventh dot green dimmer 46 0 255 eleventh dot blue dimmer 47 0 255 eleventh dot white dimmer 48 0 255 twelfth dot red dimmer 49 0 255 twelfth dot green dimmer 50 0 255 twelfth dot blue dimmer 51 0 255 twelfth dot white dimmer CLEANING AND MAINTENANCE The following points have to be considered also during the inspection 1 All screws for installing the devices or parts of the device have to be tightly connected and must not be corroded 2 There must n
12. operational breaks may ensure that the device will function properly for a long time Do not shake the device Avoid brute force when installing or operating the device The device shall only be used complete with its protective shield While choosing the installation spot please make sure that the device is not exposed to extreme heat moisture or dust The minimum distance between light output from the projector and the illuminated surface must be more than 0 1 meter Operate the device only after having familiarized with its functions Do not permit operation by persons not qualified Most damages are the result of unprofessional operation Please use the original packaging if the device is to be transported For safety reasons please be aware that all modifications on the device are forbidden If this device will be operated in any way different to the one described in this manual the product may suffer damages and the guarantee becomes void Furthermore any other operation may lead to short circuit burns electric shock crash etc FEATURES 3 pin xlr dmx input and output connectors input and output powerconn connectors Wireless Transmitter and Receiver Onboard 7 48 51 DMX 512 Channel Mode Stand Alone with Master Slave function and sound activated via Built in Microphone Multi Colors Color strobe Electronic Dimming 0 100 2 x 16 LCD operation menu with function buttons Daisy Chain Units Together with or without cables SAFETY IN
13. ot be any deformations on the housing color lenses fixations and installation spots ceiling suspension trussing 3 The electric power supply cables must not show any damage material fatigue or sediments Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed CAUTION Disconnect from mains before starting maintenance operation In order to make the lights in good condition and extend the life time we suggest a regular cleaning to the lights Due to fog residue smoke and dust cleaning the internal and external optical lenses must be carried out periodically to optimize light output Clean the external optics with glass cleaner and a soft cloth Use also normal glass cleaner and a soft cloth to wipe down the outside casing Clean frequently the fans Cleaning frequency depends on the environment in which the unit operates We recommend a frequent cleaning of the device Please use a moist lint free cloth Never use alcohol or solvents Should you need any spare parts please order genuine parts General Specifications Colors RGBW Color Mixing Dimensions 720 L x 320 W x Model QUADRO B12 LED 12 PCS 4INIRGBW 120 H mm Voltage 110V 230V 60Hz 50Hz Gross Weight 8Kgs Batteries specs Rechargeable Battery with up to 18 hours of battery life Battery power indicator 0 100 18650 type 2200MA Unit charging voltage 4 2V
Download Pdf Manuals
Related Search