quadrapaddle receiver insert part identification
Contents
1. DETAIL A EXTRACTION TOOL PINS Figure B Insert removal tool pins Figure C Seat removal tool Figure D Push removal tool plunger to module frame 2 1 For the most current information available visit www vpc com 7 30 15 QUADRAPADDLE INSERT USER S MANUAL SECTION 2 VIRGINIA PANEL CORPORATION INSERT INSTALLATION REMOVAL INSTRUCTIONS FOR i2 MX RECEIVER PART 310 130 XXX TOOLS REQUIRED VTAC Extraction Tool Kit Receiver and ITA Part 910 112 130 INSERT INSTALLATION INSTRUCTIONS 1 Ensure that the Insert s is squared up with the corresponding module VTAC HSD INSERT location Apply gentle pressure and insert the Insert s into the rear BLUE INSERT wiring side of the module shown in Figure A The Insert s can only yee go into one side Once in place gently pull the wire to ensure the 7 Insert s is fully seated INSERT REMOVAL INSTRUCTIONS 1 Group the required number of extraction tools together for the given patchcord shown in Figure B The tool pins should be on opposite sides of the patchcords or wires to be removed QUADRAPADDLE INSERT WARNING All Inserts within each patchcord must be extracted simultaneously to prevent damage to Inserts la Oe eof of oof eof oof gI gI oof oo oo NOTE The extraction tools are magnetic to aid in stacking them together 2 While grasping the extraction tool s body from the sides Figure B s2. 30 INSERT INSTALLATION INSTRUCTIONS 1 Ensure that the Insert s is in line with the corresponding module location Apply gentle pressure and insert the Insert s into the rear wiring side of the module shown in Figure A The Insert s can only go into one side Once in place gently pull the wire to ensure the Insert s is fully seated VTAC HSD INSERT BLUE INSERT ra YQ ll al A IA aU A A Ad a a INSERT REMOVAL INSTRUCTIONS 1 Group the required number of extraction tools together for the given patchcord shown in Figure B The tool pins should be on the mating side of the module a Wal al Al al AU a Ad Id eG VG OG OG GE OG UGE A aE E a WARNING All Inserts within each patchcord must be extracted QUADRAPADDLE INSERT simultaneously to prevent damage to Inserts NOTE The extraction tools are magnetic to aid in stacking them together 2 While grasping the extraction tool s body from the sides Figure B slide tool pins into module s extraction cavity square holes until the tool frame is seated against the body shown in Figure C WARNING The extraction tool s need to be seated against the module front face before the plunger is pushed in Otherwise damage to Insert s may occur Figure A Insert installation 3 Push plunger of extraction tool s in to extract Insert s The Insert s will be ejected out the wiring side of the module shown in Figure D PLUNGER
3. QUADRAPADDLE INSERT USER S MANUAL SECTION VIRGINIA PANEL CORPORATION QUADRAPADDLE RECEIVER INSERT PART IDENTIFICATION PART 510 180 101 This section will point out features designed to help determine the proper orientation of the QuadraPaddle receiver Insert Figure A as well as distinguishing features The top of the QuadraPaddle receiver Insert can be determined by the position 1 indicator designated by the triangle shown in Figure A The front and rear of the QuadraPaddle receiver Insert are shown in Figure B The front side mates with the QuadraPaddle ITA Insert The rear of the QuadraPaddle receiver Insert has the position indicator located on the top Wires exit the QuadraPaddle receiver Insert from the rear side The Insert is keyed like the VIAC HSD Insert to ensure proper orientation see VIAC User s Manual Section 2 1 Figure C POSITION 1 TRIANGLE INDICATOR POSITION 1 TRIANGLE CONTACT RETENTION INDICATOR EXTRACTION CAVITY TOP FRONT REAR MATING WIRING SIDE SIDE BOTTOM Figure A QuadraPaddle receiver Insert Figure B QuadraPaddle receiver Insert side view 1 1 For the most current information available visit www vpc com 7 30 15 QUADRAPADDLE INSERT USER S MANUAL SECTION 2 VIRGINIA PANEL CORPORATION INSERT INSTALLATION REMOVAL INSTRUCTIONS FOR RECEIVER MODULE PART 510 170 101 TOOLS REQUIRED VTAC Extraction Tool Kit Receiver and ITA Part 910 112 1
4. RAIL S INSTALLATION INSTRUCTIONS 1 To install Rail s orient rail s as shown in Figure A Figure C illustrates the identifiers to aid in orientation receiver rails shown The receiver rails are marked with RR receiver right and RL receiver left when viewing from mating face The ITA rails are marked with IR ITA right and IL ITA left when viewing from rear wiring side 2 Place rail s ledge on flat surface shown in Figure D then put halves together and tighten the two Phillips flat head screws using a Phillips head screwdriver NOTE Receiver ITA frame halves are keyed to be placed together Figure A Rail s install removal receiver shown only one direction PHILLIPS CAPTIVE SCREWS 2 a ss BLACK POSITION Al INDICATOR RL RECEIVER RR RECEIVER LEFT TOP FLAT SURFACE BOTTOM Figure B ITA frame separation Figure C Rail s Identifiers Figure D Rail s install removal receiver shown 4 For the most current information available visit www vpc com 7 30 15
5. lide tool pins into module s extraction cavity slots until the tool frame is seated against the body shown in Figure C Figure A Insert installation 3 Push plunger of extraction tool s in to extract Insert s The Insert s will be ejected out the wiring side of the module shown in Figure D WARNING The extraction tool s need to be seated against the module front face before the plunger is pushed in Otherwise damage fo Insert s may occur Ne VANAN E F E N a PUSH PLUNGER Ly pemes N NANS 4 a Le X i A v PLUNGER Figure C Seat Removal tool Figure D Push removal tool plunger 2 3 For the most current information available visit www vpc com 72015 QUADRAPADDLE INSERT USER S MANUAL SECTION 3 VIRGINIA PANEL CORPORATION QUADRAPADDLE INSERT CONTACT INSTALLATION REMOVAL INSTRUCTIONS TOOLS REQUIRED Tool Module Insert QuadraPaddle Receiver Part 910 112 131 Tool Extraction QuadraPaddle ITA Part 910110 111 CONTACT REMOVAL INSTRUCTIONS RECEIVER 1 Remove QuadraPaddle Insert from receiver frame see Section 2 1 and 2 3 QUADRAPADDLE CONTACT TABS 2 Align extraction tool protrusions to extraction cavity see Figure B and C 3 Apply pressure to QuadraPaddle contact tabs see Figure A 4 Remove patchcord from wiring side see Figure C CONTACT REMOVAL INSTRUCTIONS ITA NOTE ITA QuadraPaddle contacts can be ex
6. tracted while the QuadraPaddle Insert is in the ITA frame or after the patchcord s has been removed NOTE Install Extract ITA QuadraPaddle contacts per the QuadraPaddle User s Manual Reference contact Part 610 138 109 or 610 138 112 Figure A QuadraPaddle receiver Insert contact removal APPLY PRESSURE APPLY PRESSURE CONTACT RETENTION EXTRACTION CAVITY EXTRACTION TOOL PROTRUSIONS Figure B QuadraPaddle receiver Insert contact removal tool Figure C QuadraPaddle receiver Insert contact removal tool 3 1 For the most current information available visit www vpc com 7 30 15 QUADRAPADDLE INSERT USER S MANUAL SECTION 4 VIRGINIA PANEL CORPORATION RAIL S INSTALLATION REMOVAL INSTRUCTIONS PART 310 130 XXX AND 410 130 XXX TOOLS REQUIRED Phillios Head Screwdriver RAIL S REMOVAL INSTRUCTIONS 1 If working with a receiver use a Phillips head screwdriver to remove strain relief by removing screws Figure A The ITA will require removal of backshell first See Section 2 of this User s Manual for instructions 2 After removing strain relief backshell use a Phillips head screwdriver to remove the two Phillips flat head screws that are PHILLIPS FLAT HEAD SCREWS 2 holding the frame halves together Figure A For ITA use Phillips head screwdriver to loosen the two captive screws on the back of the rear frame Figure B 3 Pull halves apart 4 Remove Ralil s
Download Pdf Manuals
Related Search