Model 1040 Standalone Enclosure User Manual
Contents
1. Model 1040 Standalone Enclosure User Manual This device contains static sensitive components It should be handled only with proper Electrostatic Discharge ESD grounding procedures NOTE Cet quipement contient des composants sensibles aux d charges lectro statiques I doit absolument tre manipul en respectant les regles de mise a la terre afin de pr venir de telles d charges NOTICE Canoga Perkins has prepared this users manual for use by customers and Canoga Perkins personnel as a guide for the proper installation operation and or maintenance of Canoga Perkins equipment The drawings specifications and information contained in this document are the property of Canoga Perkins and any unauthorized use or disclosure of such drawings specifications and information is prohibited Canoga Perkins reserves the right to change or update the contents of this manual and to change the specifications of its products at any time without prior notification Every effort has been made to keep the information in this document current and accurate as of the date of publication or revision However no guarantee is given or implied that the document is error free or that is accurate with regard to any specification Canoga Perkins Corporation 20600 Prairie Street Chatsworth California 91311 6008 Business Phone 818 718 6300 Monday Friday 7 a m 5 p m Pacific Time FAX 818 718 6312 24 hrs Web Site www canoga com2. Email fiber canoga com Copyright 2003 2005 Canoga Perkins Corporation All Rights Reserved EdgeAccess Universal Chassis System Model 1040 User Manual Model Number 1040 UM Product Number 6913100 Rev D 01 2008 2 EdgeAccess Model 1040 Model 1040 Standalone Enclosure User Manual The Model 1040 standalone enclosure shown in Figure 1 supports one 5U sized managed module Figure 1 Model 1040 Standalone Enclosure The front provides two switches five LEDs one connector and a slot for a module The back includes an AC power cord socket and the ALM IN and ALM OUT connectors Switch Setting F1 NRM F2 for the module Fl Selects Function 1 such as Local loopback NRM Normal operation set this for most applications F2 Function 2 such as Remote loopback HDX FDX for lOBASE T port HDX Half duplex FDX Full duplex Note If the link partner is set to auto negotiation the link uses 10M and follows the HDX FDX switch setting for this port otherwise set this switch to match the other switch on the link LED State PWR Off Green ALARM MAJ and MIN Off MIN Amber MAJ Red Tx for LOBASE T port Off Green blinking LNK Rx for lOBASE T port Off Green Amber Blinking Definition No power Power is on Normal Minor alarm Major alarm No transmission Transmission activity No link Link is established at full duplex Link is established at half duplex Data 1s received Note To clear a latched Minor or Major
3. alarm push the ACK button Connector Provides ALM IN and ALM OUT MIN and MAJ Alarm status from another device IN and to another device OUT IOBASE T Half or full duplex Ethernet EdgeAccess Model 1040 Installing and Using the 1040 Enclosure To use the 1040 enclosure see Figure 1 and follow these steps 1 Place it on a secure surface with room for air flow and within 7 ft 2 134 m of the AC power source 2 Insert a module in the guide rails and press it firmly into the backplane then secure the thumbscrews finger tight 3 At ALM OUT on the rear panel connect devices to receive alarm information see Figure 2 e NO The contacts are open for normal operation and closed in a fault condition e COM The electrical common e NC The contacts are closed for normal operation and open in a fault condition 4 At ALM IN on the rear panel connect devices to supply alarm information see Figure 2 Connect cabling from the output on the device to IN on the 1040 and from the output to IN on the 1040 the internal alarm sense circuit is optically protected Connect an optional Frame or Chassis Ground to FGND 452 z z o aN d3 NI HI AOD F 6 E O L MIN mas MIN MA J eed ALM IN ALM OUT Figure 2 Model 1040 Alarm Connectors 5 Plug the power cord into the rear of the 1040 enclosure then plug it into the AC power source this turns on the power To turn off the power unpl
4. ug the power cord 6 To set any switches on the module install the module in the 1040 enclosure connect all cables and access the module see the User Manual for the module Specifications Dimensions 11 70 L x 12 0 W x 1 718 H 297 mm x 305 mm x 44 mm Weight 5 6 Ibs 2 5 kg Power 115 to 230 VAC 50 to 60 Hz autoranging 14 W maximum Operating Environment 0 to 50 C Up to 90 humidity Non condensing Regulatory Compliance e ETL cETL UL 60950 CAN CSA C22 2 No 60950 EN IEC 60950 EN 60825 1 2 e FCC Part 15B IC 003 VCCI Class A C Tick AS NZS 3548 e EN 55022 Class A EN 61000 3 2 EN 61000 3 3 e EN 55024 e CE Mark 4 EdgeAccess Model 1040 Warranty Information Current Warranty information is available on line in the Client Login Area of the Canoga Perkins web site www canoga com or by contacting Technical Support at 800 360 6642 voice or fiber canoga com email EdgeAccess Model 1040 CANOGA PERKINS CORPORATION CANOGA PERKINS 20600 Prairie Street Chatsworth California 91311 6008 USA Phone 818 718 6300 FAX 818 718 6312 Web Site www canoga com Email fiberWcanoga com
Download Pdf Manuals
Related Search