User`s Manual - Glunz & Jensen
Contents
1. p E p n Han 1504 User s Manual CONCEPT 301 D 401 D 501 D E Daily use Initial operation of the unit Start up the dryer To start the dryer press on the E located nearby the temperature indication of the desired section At this point the dot located in the bottom right corner of the display starts blinking 260 indicating the heating is ON The display change from the set temperature to the real temperature in the dryer Wait until the temperature reaches the setup point to start loading plates in the unit Drying process To start a drying process press on the 59 corresponding to the loaded drawer The display shows the bottom right dot blinking throughout the process The display shows End at the end of the drying cycle To start anew process remove the plate from the drawer and press on the E corresponding to the unloaded drawer When one of the drawers is open the corresponding section display is blinking and the section blowers are switched off User s Manual CONCEPT 301 D 401 D 501 D 1504 Maintenance E Cleaning the unit Part 3 Maintenance Cleaning the unit e Clean the unit covers from dust and dirt by using a clean damp cloth 133306 1504 User s Manual CONCEPT 301 D 401 D 501 D E Maintenance Cleaning the unit User s Manual CONCEPT 301 D 401 D 501 D 15042. or act according to the o Caution information in order to avoid any mechanical or electrical damage to the equipment The operator must observe and or act according to the A Warning information in order to avoid any personal injury 1504 User s Manual CONCEPT 301 D 401 D 501 D a General information About this manual Unintended use of the equipment Glunz amp Jensen Degraf S p A does not take any responsibility for any damage or accidents caused by unintended use of the equipment Itis absolutely prohibited to make any modifications electrical nor mechanical of the equipment If however this prohibition is disregarded Glunz amp Jensen Degraf S p A s warranty will no longer apply Intended use of the equipment This unit is a part of a full range dedicated for the treatment of flexographic printing plates This range includes exposure processor dryer and light finisher This unit is designed to drying of flexographic printing plates Installation Never install the unit in explosive environments tis the responsibility of the owner and operator s of this unit that the installation is made in accordance with local regulations and by engineers authorized to carry out plumbing and electrical installations Installation service and repair must be performed only by Service Technicians who are trained in servicing the equipment The manufacturer cannot be held responsible for any damag
3. unit is clean and free for easy movement il Check all the required supplies and connections power cable and exhaust e Turn on the main switch of the unit located at the rear side of the unit T33298 e Switch the unit on by pressing 7 button on the control panel of the unit T33299 User s Manual CONCEPT 301 D 401 D 501 D 1504 Daily use c9 Initial operation of the unit Temperature value modification To modify the temperature value press on the g and then press on the B button corresponding to the desired section A small dot is then displayed on the bottom right corner of the display Em as well as the LED located on the top right corner of the buttons indicates the possibility to modify the value g B Enter a new value using the numeric keyboard and then press the 53 to confirm the value Afterwards the dot disappears and the LED of button is off Time value modification To modify the drying time press first on 4 and then press on the 5 button corresponding to the desired drawer A small dot is then displayed on the bottom right corner of the display 220 as well as the LED located on the top right corner of the button g indicates the possibility to modify the value Enter the new value using the numeric keyboard and then press the g to confirm the value Afterwards the dot disappears and the LED of button is off editing possible value confirmed i E
4. User s Manual CONCEPT 301 D 401 D 501 D GLUNZ amp JENSEN DEGRAF User s Manual CONCEPT 301 D 401 D 501 D Edition BA January 2015 This book has part No 10077258 GB Always read the Safety Instruction Manual part No 21741 before installing or operating the equipment This manual is published by Glunz amp Jensen Degraf S p A Il Girasole Palazzo Donatello 8 03b 20084 Lacchiarella MI Italy Internet www degraf glunz jensen com Copyright 2014 by Glunz amp Jensen Degraf S p A User s Manual CONCEPT 301 D 401 D 501 D 1504 gg Table of contents Part 1 General information leeren 1 1 About this miarilldl ususarios we ety aus ot 1 1 Intended use of this manual eee II 1 1 RRESEIVATIONS iras a i dot Smeg a eg ade Ln bane at et s 1 1 Notes cautions and warnings l naasa aaaea eaa 1 1 Unintended use of the equipment 204 3424 142420 ri 1 2 Intended use of the equipment 0 0 a 1 2 installation se et ota es td e ance Gee Guns he een ee A 1 2 Selvice ASSISTANCE iuuenis ead a HR haha irn 1 2 Part 2 Daily USE orinar ana anna ae 2 1 Generaler pc ee eas Gs ee ae ee er Te ae 2 1 Safety WANNE 2 vestidas dai ed ae 2 1 Initial operation of the UNiL o o o o ooooooooo s 2 2 Temperature value modification cece eee ee ee eee 2 3 Time value modification 0 eee 2 3 Start up the AE civi
5. c sod eae SSeS EME CO Read eee 2 4 Drying process o 2 4 Part 3 Maintenance 000 eee nnn 3 1 Cleaning thou ones tee ceeds ere We dara eta RUE Y oe ieu 3 1 1504 User s Manual CONCEPT 301 D 401 D 501 D User s Manual CONCEPT 301 D 401 D 501 D 1504 General information EE About this manual Part 1 General information About this manual Intended use of this manual This manual describes the common use procedures of the unit It is intended for the daily user and should be kept with the equipment for reference at all times Reservations This manual was written and illustrated using the best possible information available at the time of publication Any differences between this manual and the equipment reflect improvements introduced after the publication of the manual Changes technical inaccuracies and typographic errors will be corrected in subsequent editions Asa part of our policy of continuous improvement we reserve the right to alter design and specifications without further notice Notes cautions and warnings Throughout the manual notes cautions and warnings are written in bold like the example below il Electrical installation must conform to local regulations and guidelines Symbol Meaning Explanation The operator should observe and or act according to the m Note information in order to obtain the best possible function of the equipment The operator must observe and
6. e caused by incorrect installation of this unit The unit is intended for installation in a restricted access location only Service assistance f help is needed to correct any problem with the equipment please contact your supplier User s Manual CONCEPT 301 D 401 D 501 D 1504 Daily use General Part 2 Daily use General This unit is designed to drying of flexographic printing plates after washout process This unit is equipped with a specific control panel which ensures very easy control Safety warnings To use this unit safely it is necessary that operators and maintenance people follow the safety instructions and safety cautions and warnings specified in the manuals For the safety of operators the unit is equipped with interlock switches for the opening of the dryer drawers during operation and with detection of the exhaust blower If any of the interlocks are not installed or closed the unit will not operate If an interlock is activated during operation the unit stops immediately Al Do not open the side or rear panels during plate processing Al For handling the plates use a safety gloves 1504 User s Manual CONCEPT 301 D 401 D 501 D Daily use Initial operation of the unit Initial operation of the unit il Make sure the room temperature is between 17 and 28 C 63 and 82 F and relative humidity on max 80 il Before turning the unit on make sure that the working area around the
Download Pdf Manuals
Related Search