Home

HL440 - User Manual

1. ER 100 FREE MEMORY 25 000 Print complet status of the only when RS232 AUX has been 4 How to use Minitimer 4 1 Recharge the internal battery before starting a new timing session gt Minitimer OFF and connected to the power supply HL 540 1 AC DC the red LED is ON while charging The red LED turns OFF when the battery is completely charged gt Minitimer ON and connected to the power supply HL 540 1 The red LED is ON while charging The red LED is OFF when the battery is completely charged The green LED is ON power supply connected Without the external power supply the green LED turns on briefly at power up and then turns off When the capacity of the battery reaches 30 the green LED flashes indicating that your Minitimer is operational for approximately 8 hours INFORMATION The capacity of the battery can be checked via the function menu lt F gt PARAMETER STATUS IMPORTANT Never charge the device under 0 C 32 F and over 30 C 86 F 4 2 Switch ON the Minitimer gt Switch ON the Minitimer gt The LCD illuminates for 5 seconds e Minitimer HL 440 and the Firmware version V A 03 gt Select how the Serial output should be used e RS232 TO PRINTER The data will be configured for a serial printer HL 200 Martel e RS232 TO AUXILIARY HL440 OR PC In this mode the synchronized data and time of day are sent with a top second signal You ll be able to adjust the baud
2. The HL670 radio system in DATA MODE also provides for the addition of a 2 MiniTimer at the finish line and for a 3 MiniTimer as a coach s monitor All time of day information will be shared live between all three HL670 transmitters connected to three MiniTimers This allows the athlete to introduce his own competitor at the start and see his time at the finish Meanwhile the coach can have his own MiniTimer to view net times and provide instant access to Session Lists and Session Rankings anywhere on the hill that is within range of the HL670 To do this it is necessary to program the coach s MiniTimer with external input data in lt settings status entries gt In the lt Settings gt menu all Capture Window times min max must be set to 0 The MiniTimer at the start is programmed to accept impulses on CH1 only and the MiniTimer at the finish is programmed to accept impulses on CH4 only This system can also expand to involve Intermediates 1 and 2 by adding additional HL670 transmitters and HL440 timers
3. 8 9 4 Chronoprinter 540 synced with a Minitimer to a Computer CP 540 Docking HL540 GPS Cable sp cial HL605 10 Settings PC 540 Synchro Synchro Manuel GPS Timing mode PTBSEQ1a4 HL 440 Synchro Synchro Slave Setup RS 232 PC gt 9600 bps RS 232 AUX gt TO AUX Input mapping Input 5 to 8 9 5 Training HL670 Rx START TRAINING Minitimer HL440 A A HL670 Tx FINISH HL2 31 Settings HL 440 Synchro Manual Synchro Setup RS 232 PC 9600 bps RS 232 AUX TO AUX Input mapping Input 1 to 4 9 6 Training with coach HL670 Rx START TRAINING Coach HL440 HL670 Rx Minitimer HL440 HL670 Tx Coach HL670 Tx FINISH Setting HL 440 1 Synchro Manual Synchro Setup RS 232 PC 9600 bps RS 232 AUX gt TO AUX Input mapping Input 1 to 4 HL 440 Coach s monitor Synchro Manual Synchro Setup RS 232 PC 9600 bps RS 232 AUX gt TO AUX Input mapping Input 1 to 4 Parameter Capture windows has to be set exactly as HL440 1 9 7 Cable Pin outs HL 605 10 Sub D9p M F 2 2 3 3 5 5 HL 200 10 Sub D9p M M 2 3 3 2 5 5 HL540 10 Sub D9p RJ45 Special cable CP540 to HL440 Synchro RJ12 CP540 RJ 11 Docking Sub D9p M D signation 3 2 5 GND 5 3 Rx Tx 1 2 1 9 SYNC IMPORTANT No data is transmitted if the Input mapping isn t set up correctly Minitimer Pa
4. Inter 1 2 and Finish On the LCD the times set by the forerunner will be shown so that you can fine tune the Capture Windows settings The times recorded by the forerunner are not included in Rankings or Listings Once the capture windows min max are set each competitor will be automatically identified as he passes through the various timing points while his run is in progress For intermediate times if the crossing time is inside of the window the bib number of the competitor will be automatically identified to the time and the MiniTimer will automatically calculate the Net Time If the crossing time is outside of this window lower or higher the time of the day will be saved but without identification It will be necessary to use the function lt R gt Recall in order to correctly identify this time if desired later e For Finish if crossing time is inside the window the time of the day will be automatically identified with bib number and the MiniTimer will calculate the net time On the other hand if crossing time is not within the window two scenarios are possible e lf the time is less than the MIN value entered in the Capture Window the time of the day will be memorized but the running time will continue to run to the end of the window MAX time e The time is greater than the MAX value entered in the capture Window parameter the time of the day will be saved but running time will automatically disappea
5. another Timing device like a CP540 or Minitimer TORS232 AUX Send Data through the serial output PRINTER gt DUPLICATE Allows another or several competitor N s to be associated with a particular start intermediate or finish time already received Not available for Training mode gt INSERT TIME Allows you to create a particular start or finish Time of Day for any competitor Not available for Training mode gt NUMBERING You can select Manual or Automatic competitor numbering assigned to input 1 Start only Automatic in ascending UP order Manual enter the competitors N ENTER At any time it is possible to cancel the next competitor by pressing O Enter This is available only on the Training Mode 6 Opening Run and Timing Enter the menu and select OPEN RUN Do not forget to unblock the external input Red key 1 4 if necessary The Minitimer records sequentially the time of day from each input Each time can be matched with a competitor n N lt 4 before the impulse or after with the RECALL function Note only in Split mode SPLIT mode Each time can be identified with a bib number N lt 4 BEFORE the start Impulse or AFTER with the function RECALL R TRAINING Mode it is important to define correctly the parameter CAPTURE WINDOWS Max Min for the Intermediates and Finish The time window min max automatically identifies the competitor number s expected
6. maximum times for Inters 1 and 2 if desired and finish Ranking Session Ranking it is possible to view or print the ranking of a training session Each competitor s fastest time of the session is given in the Session Ranking Listing listing a session For Listing you can select competitor to list all of his times from all of the runs he has taken so far for the current session For listing a session you can select a session in memory and see the time of a competitor from that specific session Input Configuration Start input 1 Intermediate 1 input 2 Intermediate 2 input 3 Finish input 4 NUMBERING You can select Manual or Automatic competitor numbering assigned to input 1 Start only Automatic in ascending UP order Manual enter the competitor s ENTER At any time it is possible to cancel the next competitor by pressing 0 Enter This is available only on the Training Mode Defining the capture Windows In training mode it is possible to send one or more forerunners to establish estimated arrival times for the training course To tell the MiniTimer that a forerunner is about to start press the key and then enter a bib N ENTER The forerunner will define the times at Inter 1 and 2 and finish As soon the forerunner crosses the finish line the Minitimer will switch automatically to the Capture Windows menu and thus allow the operator to define the MIN MAX settings for
7. the software TAGHeuerFirmManager exe ad TagHeuer Firmware Manager V5 0 ka TAGHeuer PROFESSIONAL TIMING www tagheuer timing com SerialPort com FileName Select file name START Select the Port Select the file Update HL440 xxx dat Press START on the software Power ON the HL440 The HL440 will go into a special mode Download The LDC back light will be ON but LCD will be blank 9 Assoon as the upgrade is downloaded into the HL440 validate the software with OK 10 Remove the RS232 cable from the HL440 11 The HL440 is ready to use ooo 8 RS232 and Ethernet Protocol RS232 Port settings 2400 9600 38400 57600 bds Data 8 bits 1 stop bit no parity Frame Format Data TAB CS16 CR LF TAB 0x09 CR 0x0D LF 0x0A CS16 is the sum of all data octets the sum of all the data bytes except for the characters if present module 65536 The hexadecimal result is inserted in the frame with 4 ASCII characters Example print the text Hello PL Hello lt TAB gt lt CS16 gt lt CR gt lt LF gt Data 0x50 L 0 4 Space 0x20 H 0x48 e 0x65 Ox6C Ox6C o Ox6F Sum 02B0 hexadecimal CS16 fare 00 086 000 0 68 6 060 GF 0 08 05300532 0x42 000 Flow control If any equipment connected to the RS232 port does not allow a flow min
8. A Louis Joseph Chevrolet 2300 la Chaux de Fonds Switzerland Tel 032 919 8000 Fax 032 919 9026 E mail info tagheuer timing com Http www tagheuer timing com USA Reliable Racing Supply Inc 643 Upper Glen Street Queensbury NY 12804 info reliableracing com www reliableracing com HL440 MiniTimer ADDENDUM TRAINING MODE OPERATING INSTRUCTIONS Description The latest firmware upgrade HL440_vb02 includes a Training mode which is designed for the automation of training sessions while minimizing errors caused by false impulses or racers abandoning the course DNF This mode allows you to measure up to 2 intermediate times and a finish time An estimated arrival window can be programmed for each intermediate and finish input Running times and NET times for intermediates and finishes are provided on the MiniTimer s display Net times are also provided to a scoreboard HL970 HL980 or printer A participant can take multiple runs during the session The training mode is a powerful solution for both professional sports teams and self timing venues for the general public Menu changes From power up you immediately select Printer port assignment Select from RS232 Printer RS232 Data or To HL970 980 Main menu under Timing Modes Training Mode is now included at the bottom of the list After selecting the TRAINING MODE go to Parameters and then Capture Window Here you assign minimum and
9. N OFF power switch 4 RS 232 printer display Sub D9f connector for the Martel HL200 Printer It is possible to print Online or Offline one or several runs This serial connector is also used for a Master Slave syncing Input or to send data to a TAG Heuer display board Training mode 5 Four banana jack inputs for external timing impulses and or synchronization Working contact normally open collector Ex Manual push button HL 18 photocells HL 2 31 35 start gate HL 7 1 3 Respect the correct polarity The Minitimer HL 440 provides a visual on the LCD and audio alarm should an external input remain in short circuit This feature allows you to observe the status of TAG Heuer s new direct response photocells HL 2 31 HL 2 35 and HL 2 32 serial number 7000 or higher and allows the timekeepers to instantly determine if a photocell is out of alignment YOO COGO a 11 i SDO 12 9 DODDS 13 10 Blocking Manual keys to unblock and block the External inputs 1 4 An input is blocked when the corresponding black bar is shown on the LCD display LED Power Two led lamps green and red show the battery loading progress and the external power supply function Keyboard to enter the time and date for synchronisation and for introducing competitor numbers distances and arrival windows Training mode Star Key ERROR to cancel an incorrect number you entered or to con
10. NU TAGHeuer PROFESSIONAL TIMING Minitimer HL 440 User Manual Version 06 2010 Table of contents QN 9n 0 094 Introduction Technical description Function Menus lt F gt 3 1 Power on Menu 3 2 Main Menu 3 3 Menu during a Run 3 3 1 In PTB Split mode 3 3 2 In Training mode How to use Minitimer 4 1 Recharge the internal battery before starting a new timing session 4 2 Switch ON the Minitimer 4 3 Connection to the Martel HL 200 Printer Menu F Opening Run and Timing 6 1 RECALL function R Download a new version of Firmware RS232 and Ethernet Protocol Configuration 9 1 Computer Minitimer and a Printer 9 2 Two Minitimer gt 8 synced Inputs 9 3 Chronoprinter 540 Minitimer Computer not synced together 9 4 Chronoprinter 540 synced with a Minitimer to a Computer 9 5 Training 9 6 Training with coach 9 7 Cable Pinouts 10 Technical specifications 11 Notes Introduction The Minitimer HL 440 is a professional timing system with 4 inputs using the same high Technology as our Chronoprinter 540 It is an essential general purpose timer for many applications The HL 440 has a high precision time base ideal for communication bi directionally with a computer It supersedes the popular PTB 605 and 606 Together with TAG Heuer software it is possible to print the calculated times and the name of the competitors on the Martel HL 200 printer connected to Minitim
11. R ZZZZ NNNN HH MM SS FFFFF TAB CS16 CR LF DR WWWW LULL _ _ HH MM SS FFFFF lt TAB gt lt CS16 gt lt CR gt lt LF gt Z Rank 0 9999 N Candidate number 1 9999 WWW Winner competitor number 1 9999 L Looser competitor number 1 9999 Intermediate number 1 9 H Hours 0 23 M Minutes 0 59 S Seconds 0 59 F Fraction of seconds 0 99999 e Speed VE VE NNNN SSS SSS UUUUUUU lt TAB gt lt CS16 gt lt CR gt lt LF gt Speed number 1 4 N Competitor number 1 9999 S Speed 0 000 999 999 U Speed unit Text 7 bytes e Recalled RT or downloaded Time data 01 AN A A A A AC Ax_NNNN_SSSS_CC_HH MM SS FFFFF_DDDDD lt TAB gt lt CS16 gt lt CR gt lt LF gt Competitor number 0 9999 Sequential number 0 9999 Channel number 1 99 or if manual inputs M1 M4 Hours 0 23 Minutes 0 59 Seconds 0 59 Fraction of seconds 0 99999 Day 0 32767 starting from 01 01 2000 OUmozrooz e Identification number request 10 ID lt TAB gt lt CS16 gt lt CR gt lt LF gt e Print Line PL HPL XXXXXXXXXXXXXXXXXXXXXXXX lt TAB gt lt CS16 gt lt CR gt lt LF gt X Text to print 24 bytes e Download 00 DL_RR lt TAB gt lt CS16 gt lt CR gt lt LF gt R Run number 1 99 e Recall Time RT RT_SSSS_CC lt TAB gt lt CS16 gt lt CR gt lt LF gt S Sequential number 0 9999 C Channel number 1 99 e S
12. REEN TO PRINTER Ll 1 sec to 1 100 000 sec A 1 4 A A INPUT STATUS Enter Time MAX MIN for Inter 1 Inter 2 Finish Select the Baud Rat 2400 to 57 600 Bds Special 9600 Bds Ctr Flux 5 PRINTER TO AUX TO HL970 HL980 H FRANCAIS DEUTSCH R 00 M MOIRE LIBRE _ 257000 Print the Minitimer status Select a run to download 16 00 00 16 02 10 PR T POUR LA SYNCHRO ON SCREEN TO PRINTER Lock time 1 00 to 0 01 sec PRINTER OFF MARTEL ON Select the Baud Rai 2400 to 57600 Bds pecial 9600 Bds Ctrl Flux only when RS232 AUX has been selected 3 3 Menu during a Run 3 3 1 In PTB Split mode CLOSE SESSION elect the Baud Rate RS232 PC 2400 to 57 600 Bds Special 9600 Bds Ctrl Flux TOP PRINTER PRINTER OFF RS232 AUX TO AUX roped es TO HL970 HL980 FRANCAIS PARAMETERS LANGUAGE DEUTSCH ITALIANO BATTERY 100 STATUS FREE MEMORY 25000 Print complet status of the PRINT SETTING Minitimer PRINTER OFF PRINTER MARTEL ON TO COMPUTER only when RS232 AUX has been TO CHRONO RS232 Select a run to download selected TO RS232 AUX DOWNLOAD 3 3 2 In Training mode CLOSE SESSION ON SCREEN TO PRINTER RANK A SESSION LISTING Select a bib number LIST A SESSION Select a session g E PARAMETERS LOCK TIME RS232 PC RS232 AUX STATUS PRINT SETTING PRINTER OFF TO COMPUTER TO CHRONO RS232 TO RS232 AUX
13. X C if command completed F if command failed or item not found e HL440 Identification number ID ID NNNNN lt TAB gt lt CS16 gt lt CR gt lt LF gt N ID number 0 65535 e Open new Run OP OP RR TAA XXXXXXXXXXXXXXXXXXX lt TAB gt lt CS16 gt lt CR gt lt LF gt Run number 1 99 If T the added run is a combination of other run Added to Run 1 99 Timing Mode Text 19 bytes x gt dT e Close Run CL CL RR lt TAB gt lt CS16 gt lt CR gt lt LF gt R Run number 1 99 e Download Run Start DS DS RR TAA XXXXXXXXXXXXXXXXXXX lt TAB gt lt CS16 gt lt CR gt lt LF gt R Run number 1 99 T the added run is a combination of other run A Added to Run 1 99 X Timing Mode Text 19 bytes e Download Run End DE DE RR lt TAB gt lt CS16 gt lt CR gt lt LF gt R Run number 1 99 e Time data TN T T T T TC Tx NNNN SSSS CC HH MM SS FFFFF DDDDD lt TAB gt lt CS16 gt lt CR gt lt LF gt N Competitor number 0 9999 S Sequential number 0 9999 C Channel number 1 99 or if manual inputs M1 M4 H Hours 0 23 M Minutes 0 59 S Seconds 0 59 F Fraction of seconds 0 99999 D Day 0 32767 starting from 01 01 2000 e Inter Diff Run and Added Run Result IR DR RR GR IRI NNNN HH MM SS FFFFF lt TAB gt lt CS16 gt lt CR gt lt LF gt RR ZZZZ NNNN _ _ HH MM SS FFFFF lt TAB gt lt CS16 gt lt CR gt lt LF gt G
14. anual Green Key 1 4 or if the system should be synchronized as along with another device from an external input 1 4 do not forget to unblock the associated external input Red key 1 4 e Slave synchro e This will put the Minitimer in Slave mode The Device will wait for the time of day information through the serial Input Printer from another Minitimer master Chrono Mode PTB Sequential 1 to 4 or 5 to 8 Sequential recording of time of Day on 4 channels 8 channels if 2 HL 440 s are connected together with RS232 connection This mode does not calculate Net Times In this mode bib number entry is not possible SPLIT 1 to 4 or 5 to 8 Sequential recording of time of Day on 4 channels 8 channels if 2 HL 440 s are connected together with RS232 connection This mode will not calculate Net Times In this mode it is possible to enter bib numbers TRAINING This mode allows you to perform automatic timing for Training sessions with a Start two intermediates and a Finish This mode will automatically recognize the bib numbers after the start at both intermediate locations and at the finish through the Capture windows information specified in the Parameters Menu IMPORTANT In the TRAINING MODE several runs for a competitor can be memorised for later analysis during a timing session gt RANKING RANK A SESSION only into the Training mode Ranking of the current timing session or any memori
15. arrival as he passes through the various timing points while his run is in progress e For intermediate times if the crossing time is inside of the window the bib number of the competitor will be automatically identified to the time and the MiniTimer will automatically calculate the Net Time If the crossing time is outside of this window lower or higher the time of the day will be saved but without identification It will be necessary to use the function lt R gt Recall in order to correctly identify this time if desired later e For Finish if crossing time is inside the window the time of day will be automatically identified with bib number and the MiniTimer will calculate the Net Time On the other hand if the crossing time is not within the window two scenarios are possible e If the time is less than the MIN value entered in the Capture Window the time of the day will be memorized but the running time will continue until the end of the window MAX time e If the time is greater than the MAX value entered in the capture Window parameter the time of the day will be saved but running time will automatically disappear at the MAX value and competitor number will be identified as a DNF Do Not Finish Defining the capture Windows 6 2 In training mode it is possible to send one or more forerunners to establish estimated arrival times for the training course To tell the MiniTimer that a forerunner is about to star
16. d with this N indicates that this time was recalled and associated with a bib number Direct time identification on an input PressR Select Input When a new time arrives identify it immediately by entering the competitor N Validate with lt 4 Cancel errant time Press R Select Input Select the errant time by using UP DOWN arrows Press to request the change Press 0 to cancel the time Press to valid the cancelling o Change indentified time PressR Select Input Selectthe time you want to change the identification by using UP DOWN arrows Press to request the change Enter the new bib s number Validate with lt ATTENTION A time identified with competitor O deletes the time The character C is memorized and associated with the time 7 Download a new version of Firmware Program downloads and new releases of the TAG Heuer firmware up loader are available free of charge on our website www tagheuer timing com For this operation you need to have e Sub D9p cable HL 605 10 e The software TAGHeuerFirmmanager exe installed on your PC Procedure 1 Copy the software TAGHeuerFirmManager exe onto your hard drive 2 Connect the HL440 with the external power supply The HL440 should be off before plugging in the external power supply Do not turn on the HL440 yet 3 Connect the RS232 cable HL605 10 to the PC and to the HL440 4 Run
17. er It memorizes 30 000 times in 99 timing sessions with a user selected precision between 1 second and 1 100 000 of second The Minitimer can be connected to our Martel HL 200 printer enabling the printing of times on line ON LINE or in download mode OFF LINE The HL 440 can be used at the start of a race Alpine skiing for example as a numerical keyboard to identify the competitor s number As soon as the competitor leaves the start both the time and the competitor number will be transmitted to the timekeeper by wire connection or by our radio transmission system HL 670 or HL 680 It is also an excellent backup system manual or automatic The competitor number can be introduced before or after the timing impulse RECALL function Two Minitimers can be connected together or to a Chronoprinter 540 to provide up to 8 input channels The Minitimer has a special timing mode called Training which is designed for the automatic training sessions Start Inter 1 Inter 2 and Finish 2 Technical description 1 RS 232 PC Sub D9f connector for bidirectional serial communication with PC It is possible to download Online or Offline one or several sessions This serial connector is also used for a Master Slave syncing Output 2 Power External power supply to recharge the internal batteries Power supply HL540 1 110 220 Vac 12 Vdc Connection to an external 12Vdc battery is possible by using the HL520 17 cable 3 O
18. firm a menu option Also used to cancel printing R Key RECALL to access the unassigned memorized times of a channel for identification UP DOWN keys to navigate the menu and to scroll through the unassigned memorized times ENTER to confirm a menu selection time date or competitor number Green Keys Manual Impulse and time of day synchronization Warning The manual timing keys 1 to 4 do not guarantee timing precision Only two simultaneous impulses can be processed at a time from the manual keys 3 Function Menus lt F gt 3 1 Power on Menu MINITIMER HL 440 V A 03 TAG HEUER RS232 TO PRINTER RS232 TO AUX SYNCHRO MANUAL SYNCHRO SLAVE TO HL970 HL980 2400 Bds 9600 Bds 9600 Bds CTRL FLUX 38400 Bds 57600 Bds 16 00 00 SYNCHRO 16 02 10 DATE lt JMA gt dd mmlyy READY FOR SYNCHRO TIME lt HM gt hh mm READY FOR SYNCHRO 3 2 Menu 16 00 00 16 02 10 MEMORY FREE 25000 ENTER TO MENU gt F OPEN SESSION SYNCHRO TIMING MODE CLEAR MEMORY LIST A SESSION PARAMETERS Open a new session SYNCHRO MANUAL SYNCHRO SLAVE PTB SEQUENTIAL 1 4 PTB SEQUENTIAL 5 8 SPLIT 1 4 SPLIT 5 8 TRAINING LOCK TIME INPUT STATUS CAPTURE WINDOW BEEP RS232 PC RS232 AUX PRINTER OFF MAREL ON O PRIN TO COMPUTER TO CHRONO RS232 TO RS232 AUX SYNCHRO DATE lt JMA gt dd mm aa TIME HM hh mm FOR SYNCHRO ON SC
19. he system information locking status of the input time of day and bib number entered by the keypad e Line 2 displays the bib number at the start along with the start time of day e Line 3 displays the bib number the input for the intermediate 1 or 2 the time of day of the Intermediate for 2 seconds and then the NET Time calculated by the Minitimer for 5 seconds e Line 4 displays the bib number next to arrive at the finish line along with the running time When the racer finishes the time of day will be shown for 2 seconds and then the Net Time will be shown for 5 seconds e Net time precision on the LCD Printer and ext Display HL970 980 Parameters setting Net time expressed to 1 10 1 sec 1 100 1 1 1000 01 1 10000 001 Wireless timing For wireless applications the MiniTimer is ready to go with the HL610 impulse only for short range projects up to 1k line of sight For long range projects the new HL670 can be used in either impulse or data mode This form of traditional wireless timing relies upon timing impulses and can expand to include the two Intermediate timing points For example Simple short range system Start Finish bib entry at the finish 1 HL610X 1 HL7 3 at the start 1 HL440 HL2 31 1 HL610R at the finish Long range system with Intermediate times bib entry at the start 1 HL440 1 HL670R 1 HL7 3 at the start 3 HL2 31 3 HL670X at Inters 1 amp 2 and the finish
20. imum of 2400 bps ex Radio transmission a basic flow control is available Go into Parameters RS232 menu then select 9600bds Flow Ctrl Once this option is activated the HL440 sends the first Frame and waits to receive the characters 0x06 ACK before sending the next one Message list HL440 to PC Frame ID s AK PC command acknowledge Every PC to CP540 message is acknowledge ID HL440 Identification number OP Open Run CL Close Run DS Download Run Start DE Download Run End TN New Time data T Unassigned Time T Re identified Time T Manually Inserted Time Duplicated Time TC Cancelled Time IR Intermediate Result DR Differential Result RR Run Result GR Result add to another Run Result VE Speed AN Recalled or Downloaded Time original A Recalled or Downloaded Time De identified Recalled or Downloaded Time Re identified Recalled or Downloaded Time Manually Inserted Recalled or Downloaded Time Duplicated Time AC Recalled or Downloaded Time Cancelled Time PC to HL440 Frame ID s 0 Identification number request PL Print Line 24 characters DL Download Run RT Recall Time SL Start List BM Send message to all ports RS232 Ethernet GSM Save Identification number MAC address LSB to Flash HL440 to PC Frames Note In the following frame the character represents a space e PC command acknowledge AK AK_X lt TAB gt lt CS16 gt lt CR gt lt LF gt
21. r at the MAX value and competitor number will be identified as a DNF If the competitor s finish time of day was a valid finish but outside of the window it will be necessary re identify the competitor s start and finish time of days using the lt R gt function This system allows you to certify with the greater likelihood that times are properly identified and false impulses passages through photocells inadvertently are not taken into account At any time it is possible to cancel an errant time To do this you select the channel concerned channel use the up down arrows to select the time you wish to cancel and then press the key followed by 0 Validate by pressing the key one more time It is possible to change the identification of a time with a different competitor N through the same process by entering any number other than 0 IMPORTANT If the value entered in time min max is 0 the window is completely open IMPORTANT In the TRAINING mode the HL440 accepts multiple times for the same competitor number from the start to the finish and for multiple runs However for the RANKING classification only the best time of a competitor from all of his runs is given IMPORTANT We also recommend that you keep track of your starting list of competitor numbers in order to identify the ones that didn t finish within the arrival window On the LCD display e Line 1 displays t
22. rameters Input Mapping CP 540 Parameters Input Status 10 Technical specifications gt General Inputs Outputs gt Keyboard gt Display Time Base U Operating temperature Charging temperature Operating time Internal power supply External power supply U U vu v UY Dimensions Weight Stand alone sports timing system Timing calculation Speed to the 1 1 600 000 sec Timing resolution printer PC from 1 sec to 1 100 000 sec Memory of 30 000 times and 99 timing sessions Sequential N competitor N from 1 to 9 999 Four banana jack inputs for external timing impulses working contact open collector COMPUTER Bidirectional RS232 or to drive external display PRINTER RS232 Expansion port available for future Docking Stations Numeric keyboard Three keys UP DOWN and ENTER Four validation keys 1 4 RECALL key Four manual toggle keys to block and unblock the external Inputs Matrix LCD display Adjustable contrast Thermo compensated quartz 12 8 MHz Precision 0 5 ppm at 25 C Precision 1 5 ppm between 20 and 55 4 F 20 C to 131 F 55 C 32 F 0 C to 86 F 30 C 38 hours 1 incoming impulse every 5 seconds Rechargeable Li ion battery 12 V DC by adaptor HL540 1 or 12 V batteries 197 x 105 x 35 mm Minitimer only 500g 11 Notes ell TAGHeuer PROFESSIONAL TIMING TAG Heuer PROFESSIONAL TIMING 6
23. rate We recommend using 9600 Bds e Select your synchronizing method Synchro Manual e Enter the current date and confirm with lt 4 e Enter the time of day format HH MM and confirm with 4 1 e Synchronize the Minitimer with any Green Manual Impulse Key 1 4 If the timer is to be synchronized with another device with an external input 1 4 do not forget to unblock the input Red key 1 4 The LCD display shows e Four black bars which indicate that all the four inputs are blocked e time of the day and the date Synchro Slave This will put the Minitimer in Slave mode The Device will wait for the synchronized time of day information through the serial Input Printer from a master Minitimer For more information please refer to configuration at the end of this user manual 4 3 Connection to the Martel HL 200 Printer e Read the printer user s manual carefully e Connect the printer to the Sub D9f on the right e First turn on the printer and then turn on the Minitimer 5 Menu gt OPEN RUN start a new timing run after closing the previous run The run number is displayed when input 1 is unblocked CLOSE RUN Exit the current run with this option Times will be saved but cannot be modified later gt SYNCHRO to establish a new time of day synchronization e Manual synchro e Enter Synchro Date dd mm yy and Time hh mm confirm with lt 4 e Synchro the Minitimer with the M
24. t press the key and then enter a bib N ENTER The forerunner will define the times at Inter 1 and 2 and finish As soon the forerunner crosses the finish line the Minitimer will switch automatically to the Capture Windows menu and thus allow the operator to define the MIN MAX settings for Inter 1 2 and Finish On the LCD the times set by the forerunner will be shown so that you can fine tune the Capture Windows settings The times recorded by the forerunner are not included in Rankings or Listings It is possible to cancel the new starter in SPLIT and TRAINING mode by entering the bib s number 0 and valid with lt RECALL function R This allows you to o Recall all the memorized times from any input from the buffer with or without competitor numbers Review and select times not yet identified with a bib number Example PressR Select Input Scroll Up Down with the and A keys Place the black arrow with the desired time _ gt 16 55 40 789 Enter the competitor number and confirm with 4 1 The symbol is associated with this N indicates that this time was recalled and associated with a bib number Recall competitor N and modification Example Enter the competitor N PressR Select Input The competitor N to modify will be displayed Press error and enter the new competitor Confirm with lt 4 The symbol is associate
25. tart List HSL Delete memorized list SLR lt TAB gt lt CS16 gt lt CR gt lt LF gt Add competitor number in the list SLA_NNNN lt TAB gt lt CS16 gt lt CR gt lt LF gt Close a new list SLC lt TAB gt lt CS16 gt lt CR gt lt LF gt N Competitor number Send message to all ports BM HBM XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX lt TAB gt lt CS16 gt lt CR gt lt LF gt X Message 1 32 octets characters lt TAB gt lt CR gt are not authorized Serial port setup factory setup HMC 04660 XXXXX lt TAB gt lt CS16 gt lt CR gt lt LF gt X Serial 0 65535 9 Configuration 9 1 Computer Minitimer and a Printer HL605 10 HL 200 10 Settings HL 440 Synchro Synchro Manual Setup RS 232 PC gt 9600 bps RS 232 AUX gt PRINTER Input mapping Input 1 to 4 9 2 Two Minitimer gt 8 synced Inputs HL 440 1 HL 440 2 HL605 10 RS232 Synchro HL 200 10 Settings HL 440 1 Synchro Synchro Manual Setup RS 232 PC 9600 bps RS 232 AUX gt AUX Input mapping Input 5 to 8 440 2 Synchro Synchro Slave Setup RS 232 PC gt 9600 bps RS 232 AUX gt VERS PRINTER Input mapping Input 1 to 4 9 3 Chronoprinter 540 Minitimer Computer not synced together HL540 10 HL 200 10 HL605 10 Settings CP 540 Synchro Synchro Manual Timing mode SEQ 1 to 4 HL 440 Synchro Synchro Manuel Settings RS 232 PC 9600 bps RS 232 AUX VERS AUX Input mapping Input 5 to
26. tifies the competitor number as he passes through the various timing points while his run is in progress If the value is defined at 0 no restrictions are activated there is no guaranty that the competitor will be correctly identified BEEP Audio Signal activation ON OFF The last setting is memorized RS232 PC Baud rate is selectable 2400 9600 38 400 57 000 and 9 600 Bds Select Flow Control for our radio Data Voice transmission HL 680 RS232 AUX Data bus RS232 PRINTER TO PRINTER printer ON OFF TO AUX Serial bus RS232 PRINTER is setup for Master Slave mode gt ToHL970 HL980 will send information to a display including Net Time especially for the Training Mode LANGUAGE The Minitimer is programmed in English German French and Italian STATUS Capacity of the memory available number of runs memorized and battery status in 96 PRINT SETTING print the full parameter settings of your Minitimer including memory status timing mode precision and input lock time PRINTER PRINTER OFF No output available Serial bus is closed PRINTER ON Times and Data are send to the Serial Printer connection IMPORTANT When you turn on the Printer all saved data will be printed gt DOWNLOAD TOPRINTER Print all Times and data on the serial printer o COMPUTER Send all data to the serial connection Computer in a traditional protocol o CHRONO RS232 Send Data to
27. zed session Note that only the best time of each competitor will be displayed on the LCD or printed LISTING LIST A SESSION only into the Training mode This is a listing of a competitor number s times in chronological order for the current session or any memorized session All the times Inter 1 2 and Finish will be displayed for each run within the session 01 COMPETITOR 1 INTER 1 10 23 INTER 2 23 56 FINISH 42 98 gt CLEAR MEMORY Clear the memory only when you start a new timing session and you are sure you do not need to retain the previous session s in memory gt PARAMETERS o PRECISION you can choose the timing precision between 1 sec to 1 100 000th of second The LCD display will show a maximum precision of 1 1000 of second however all times transferred memorized and printed are at the specified precision LOCK TIME Lock out time of the 4 inputs is selectable from 0 01 to 9 99 seconds To enter 1 00 Sec press 1 0 0 and confirm with 4 The minimum lock out time of 0 01 sec should not be used with any mechanical triggering device bounce may cause several impulses INPUT STATUS Selection of Inputs and their timing info functions info transmit received UP Narrow TRANSMIT DOWN Narrow Received HORIZONTAL Close The default status of the input is set as Transmit after switching off CAPTURE WINDOWS only into the Training mode The time window min max automatically iden

HL440 - User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents