FAVORIT 88009 W0P/AU FAVORIT 88009 M0P/AU EN User manual
Contents
1. Manual adjustment Turn the water hardness dial to the posi tion 1 or2 Electronic adjustment 1 Press the on off button to activate the appliance Make sure that the ap pliance is in setting mode refer to Setting and starting a program Press and hold at the same time De lay and Start until the indicators of AUTO PRO ana SILENT start to flash Press Progra The indicators of PRO and SILENT 99 off The indicator of AUTO contin ues to flash e The display shows the current set ting of the water softener e g 5 I level 5 Press Program again and again to change the setting Press the on off button to deactivate the appliance and to confirm the set ting ENGLISH 11 6 2 Filling the salt container 1 Turn the cap counterclockwise and open the salt container 2 Put 1 litre of water in the salt con tainer only for the first time 3 Fill the salt container with dishwash er salt 4 Remove the salt around the opening of the salt container 5 Turn the cap clockwise to close the salt container IN CAUTION Water and salt can come out from the salt container when you fill it Risk of corrosion To pre vent it after you fill the salt con tainer start a program Press the release button D to open the lid C Fill the rinse aid dispenser A no more than the mark max Remove the spilled r2. available c have the proof of purchase eg an invoice available d telephone the numbers shown below You accept that if you make a war ranty claim AEG and its ASC may exchange information in relation to you to enable AEG to meet its obli gations under this warranty Important Notice 22 www aeg com Before calling for service please ensure that the steps listed in point 13 above have been followed SERVICE AUSTRALIA HAEG www aeg com au FOR SERVICE or to find the address of your nearest state service centre in Australia PLEASE CALL 1300 363 664 OR EMAIL customercare aegaustralia com au For the cost of a local call Australia only FOR SPARE PARTS or to find the address of your nearest state spare parts centre in Australia PLEASE CALL 13 13 50 OR EMAIL customercare aegaustralia com au For the cost of a local call Australia only SERVICE NEW ZEALAND HAEG FOR SERVICE or to find the address of your nearest authorised service centre in New Zealand FREE CALL 0800 10 66 10 OR EMAIL customercare electrolux co nz New Zealand only FOR SPARE PARTS or to find the address of your nearest state spare parts centre in New Zealand FREE CALL 0800 10 66 20 OR EMAIL customercare electrolux co nz New Zealand only 14 ENVIRONMENT CONCERNS Recycle the materials with the appliances Do not dispose symbol amp Put the packaging in appliances marked with the symbol 2 applicable containers
3. the program duration is long 4 With this program you can wash a load with fresh soil It gives good washing results in a short time 5 With this program you have the most efficient use of water and energy consumption for crockery and cutlery with normal soil This is the standard program for test institutes 6 With this program you can wash a load with mixed soil Very heavy soil in the lower basket and normal soil in the upper basket The water pressure and the water temperature in the lower basket are higher than in the upper basket 8 www aeg com Consumption values Program Duration Energy Water min kWh I AUTO 90 160 0 9 1 7 8 15 PRO 140 160 1 5 1 6 13 14 SILENT 200 220 el 11 2 9 11 30MIN 30 0 9 9 ECO 147 161 0 79 0 96 10 4 12 6 50MIN 50 60 1 0 1 2 10 11 Yh 130 140 1 4 1 5 14 15 y 70 80 0 8 0 9 11 12 1 The pressure and the temperature of the water the variations of the mains supply the options and the quantity of dishes can change the values Information for test institutes For all the necessary information for test performance send an email to info test dishwasher production com Write down the product number PNC that is on the rating plate 5 OPTIONS Activate or deactivate the op tions before the start of a pro gram You cannot activate or de activate the options while a pro gram operates i If one or more options are set make sure that the re
4. washing re sults Make a check regularly and if necessary clean them 1 Turn the filter A counterclockwise and remove it 2 ENGLISH 15 To disassemble the filter A pull apart A1 and A2 Remove the filter B Wash the filters with water Before you put the filter B back make sure that there are no residues of food or soil in or around the edge of the sump Make sure that the filter B is cor rectly positioned under the 2 guides C Assemble the filter A and put it back in filter B Turn it clockwise until it locks An incorrect position of the filters can cause bad washing results and damage to the appliance 9 2 Cleaning the spray arms Do not remove the spray arms If the holes in the spray arms are clog ged remove remaining parts of soil with a thin pointed object 9 3 External cleaning Clean the appliance with a moist soft cloth Only use neutral detergents Do not use abrasive products abrasive cleaning pads or solvents 10 TROUBLESHOOTING The appliance does not start or it stops during operation Before you contact the Service refer to the information that follows for a solu tion to the problem With some problems the display shows an alarm code e IQ The appliance does not fill with water Problem 9 4 Internal cleaning If you regularly use short duration pro grams these can leave deposits of grease and li
5. FAVORIT 88009 WOP AU EN User manual 2 iz FAVORIT 88009 MOP AU WAEG perfekt in form und funktion 2 www aeg com CONTENTS enaupunp SAFETY INSTRUCTIONS ea a eu ea 8 PRODUCT DESCRIPTION see ae ee GONTROLBANER ass ea Eee en een ee PROGRAMS 3040 04 Kiss bid bhdd boda nem ee en eg ee Dane OPTIONS 2 een re nee erg BEFORE FIRS TSE 4 rn en a ee enden date een DAILY USB a ee ee ech age HINTS AND TIPS 2335 20g aa aetna ee a a a Haken 9 CARE AND CLEANING Hs ss 22242 add ae Peds Sd nen hee lees 10 TROUBLESHOOTING o sascha en 11 TECHNICAL INFORMATION 2 23 220 22 82 ba a au bard aed eed an MAINS FALA MON ee ee tote tener toate en ee er Male 13 WARRANTY u se ed edad tae ei TE FOR PERFECT RESULTS Thank you for choosing this AEG product We have created it to give you impeccable performance for many years with innovative technologies that help make life simpler features you might not find on ordinary appliances Please spend a few minutes reading to get the very best from it Visit our website for Get usage advice brochures trouble shooter service information www aeg com Register your product for better service www aeg com productregistration Buy Accessories Consumables and Original spare parts for your appliance www aeg com shop iw amp CUSTOMER CARE AND SERVICE We recommend the use of original spare parts When contacting Service ensure that
6. ICAL INFORMATION Make sure that the local water authority gives you the average mains pressure in your area Water drain hose The highest point of the drain hose must be no more than 600 mm from the floor ENGLISH 19 and must have a continuous fall to the plumbing connection The drain hose can be lengthened using additional lengths and connectors These must be purchased from Electro lux Spare Parts The extension length must not exceed 2 metres The drain hose must be free of obstruc tions Remove the sink plug when the appli ance drains the water to prevent that the water goes back into the appliance The appliance has a security feature to prevent dirty water going back into the appliance If the spigot of the sink has a non return valve this valve can cause the appliance to drain incorrectly Remove the non return valve Remove entire internal membrane If you connect the water drain hose to a trap spigot under the sink remove the plastic membrane If you do not remove the membrane remaining food can cause a blockage in the drain hose spi got 20 www aeg com 13 WARRANTY HAEG FOR SALES IN AUSTRALIA AND NEW ZEALAND ALL AEG BRANDED APPLIANCES This document sets out the terms and conditions of the product warranties for AEG Appliances It is an important document Please keep it with your proof of purchase documents in a safe place for future reference should you re
7. appliance operates If you open the door the appliance stops When you close the door the ap pliance continues from the point of inter ruption Cancelling the delay start while the countdown operates When you cancel the delay start also the program is cancelled 1 Press and hold at the same time De lay and Start until all the program in dicators come on and the display shows 2 horizontal status bars 2 Setthe program again Cancelling the program 1 Press and hold at the same time De lay and Start until all the program in dicators come on and the display shows 2 horizontal status bars Make sure that there is detergent in the detergent dispenser be fore you start a new program At the end of the program The display shows 0 and the end indica tor comes on 1 Press the on off button to deactivate the appliance 2 Close the water tap i If you do not press the on off button the Auto Off function au tomatically deactivates the appli ance a few minutes after the end ofthe program This helps to decrease the ener gy consumption 8 HINTS AND TIPS 8 1 The water softener Hard water contains a high quantity of minerals that can cause damage to the appliance and bad washing results The water softener neutralises these miner als The dishwasher salt keeps the water softener clean and in good conditions It is important to set the right level of the water softener This makes su
8. d horn aluminium pew ter and copper Refer to the supplied leaflet with examples of the load of the bas kets e Do not put in the appliance items that can absorb water sponges household cloths e Remove remaining food from the items e To remove easily remaining burned food soak pots and pans in water be fore you put them in the appliance e Put hollow items cups glasses and pans with the opening down e Make sure that cutlery and dishes do not bond together Mix spoons with other cutlery e Make sure that glasses do not touch other glasses 9 CARE AND CLEANING WARNING Before maintenance deactivate the appliance and disconnect the mains plug from the mains sock et A 9 1 Cleaning the filters e Put the small items in the cutlery bas ket Put the light items in the upper bas ket Make sure that they do not move e Make sure that the spray arms can move freely before you start a pro gram 8 4 Before starting a program Make sure that e The filters are clean and correctly in stalled e The spray arms are not clogged e The position of the items in the bas kets is correct e The program is applicable for the type of load and for the degree of soil e The correct quantity of detergent is used e There is dishwasher salt and rinse aid unless you use combi detergent tab lets e The cap of the salt container is tight Dirty filters and clogged spray arms decrease the
9. he point of interruption If the problem occurs again contact the Service If the display shows other alarm codes contact the Service 10 1 If the washing and drying results are not satisfactory Whitish streaks or bluish layers on glasses and dishes e The released quantity of rinse aid is too much Adjust the rinse aid selector to a lower position e The quantity of detergent is too much Stains and dry water drops on glasses and dishes e The released quantity of rinse aid is not sufficient Adjust the rinse aid se lector to a higher position e The quality of the detergent can be the cause or with a low temperature drying phase Leave the door ajar for some minutes before you remove the dishes e The rinse aid dispenser is empty e The quality of the rinse aid can be the cause e The quality of the combi detergent tablets can be the cause Try a differ ent brand or activate the rinse aid dis penser and use rinse aid together with the combi detergent tablets i Refer to HINTS AND TIPS for other possible causes 10 2 How to activate the rinse aid dispenser The activation of the rinse aid dispenser can occur only with the Multitab option activated 1 Press the on off button to activate the appliance Make sure that the ap pliance is in setting mode refer to Setting and starting a program 2 Press and hold at the same time De lay and Start until the indicato
10. in this case h you means the purchaser of the Appliance not having purchased the Appliance for re sale and your has a corresponding mean ing This warranty only applies to Appli ances purchased and used in Aus tralia or New Zealand and is in addi tion to and does not exclude re strict or modify in any way any non excludable statutory warranties in Australia or New Zealand During the Warranty Period AEG or its ASC will at no extra charge if your Appliance is readily accessible for service without special equip ment and subject to these terms and conditions repair or replace any parts which it considers to be defec tive AEG or its ASC may use rema nufactured parts to repair your Ap pliance You agree that any replaced Appliances or parts become the property of AEG This warranty does not apply to light globes batteries filters or similar perishable parts Parts and Appliances not supplied by AEG are not covered by this war ranty You will bear the cost of transporta tion travel and delivery of the Appli ance to and from AEG or its ASC If you reside outside of the service area you will bear the cost of a travel of an authorised represen tative b transportation and delivery of the Appliance to and from AEG or its ASC In all instances unless the Appliance is transported by AEG or an AEG au thorised representative the Appli ance is transported at the owner s cost and
11. inse aid with an absorbent cloth to prevent too much foam Close the lid Make sure that the re lease button locks into position You can turn the selector of the released quantity B between position 1 lowest quantity and position 4 highest quantity 7 DAILY USE 1 Open the water tap 2 Press the on off button to activate w Load the baskets Add the detergent gt the appliance Make sure that the ap e Ifyou use the combi detergent pliance Is In setting mode refer to tablets activate the Multitab op Setting and starting a program tion e f the salt indicator is on fill the salt 5 Set and start the correct program for container the type of load and the degree of e f the rinse aid indicator is on fill soil the rinse aid dispenser 12 www aeg com 7 1 Using the detergent Press the release button B to open the lid C 2 Putthe detergent in the compart ment A 3 Ifthe program has a prewash phase put asmall quantity of detergent on the inner part of the appliance door 4 Ifyou use detergent tablets put the tablet in the compartment A 5 Close the lid Make sure that the re ease button locks into position 7 2 Setting and starting a program Setting mode For some settings it is necessary that the appliance is in setting mode Press the on off button to activate the appliance The appliance is in setti
12. lated indi cators are on before the program starts i 5 1 ExtraHygiene With this option you have better hygiene results During the rinsing phase the temperature stays at 70 C for at least 10 minutes How to activate the ExtraHygiene option 1 Press Option until the ExtraHygiene indicator comes on In the display you can see the update of the pro gram duration e Ifthe option is not applicable to the program the related indicator does not come on 5 2 OKO PLUS This option decreases the temperature in the last rinse phase The use of this option decreases the en ergy consumption up to 25 and the program duration The dishes can be wet at the end of the program How to activate the OKO PLUS option 1 Press Option until the OKO PLUS in dicator comes on In the display you 6 BEFORE FIRST USE 1 Make sure that the set level of the water softener agrees with the water hardness in your area If not adjust the water softener Contact your local water authority to know the water hardness in your area 2 Fill the salt container ENGLISH 9 can see the update of the program duration e Ifthe option is not applicable to the program the related indicator does not come on 5 3 Multitab Activate this option only when you use the combi detergent tablets This option deactivates the use of rinse aid and salt The related indicators stay off The program duration can increase How to ac
13. mescale inside the appli ance To prevent this we recommend to run long duration programs at least 2 times per month e Cf The appliance does not drain the water e Jf The anti flood device is on WARNING Deactivate the appliance before you do the checks Possible solution You cannot activate the appli ance Make sure that the mains plug is connected to the mains socket 16 www aeg com Problem The program does not start Possible solution Make sure that there is not a damaged fuse in the fuse box Make sure that the appliance door is closed Press Start If the delay start is set cancel the setting or wait for the end of the countdown The appliance does not fill with water Make sure that the water tap is open Make sure that the pressure of the water supply is not too low For this information contact your local water authority Make sure that the water tap is not clogged Make sure that the filter in the inlet hose is not clogged Make sure that the inlet hose has no kinks or bends The appliance does not drain the water Make sure that the sink spigot is not clog ged The anti flood device is on Make sure that the drain hose has no kinks or bends Close the water tap and contact the Service After the checks are completed activate Dishes are wet the appliance The program continues e The program is without a drying phase from t
14. ng mode when all the program indicators come on and the display shows 2 hori zontal status bars If the control panel does not show this condition press and hold at the same time Delay and Start until the appliance is in setting mode Starting a program without delay start 1 Open the water tap 2 Press the on off button to activate the appliance Make sure that the ap pliance is in setting mode sd Close the appliance door 4 Press Program again and again until the indicator of the program you want to set comes on You can also set the applicable options e The duration of the program flash es in the display e The indicators of the phases that are foreseen for the program come on 5 Press Start to start the program e When the program starts only the indicator of the running phase stays on e The program duration starts to de crease with steps of 1 minute Starting a program with delay start 1 Set the program 2 Press Delay again and again until the display shows the delay time you want to set from 1 to 24 hours e The Delay indicator comes on e The delay time flashes in the dis play The indicators of the phases that are foreseen for the program go off 3 Press Start to start the countdown e The countdown starts to decrease with steps of 1 hour When the countdown is completed the program starts The indicator of the run ning phase comes on Opening the door while the
15. nter 820 mm min 1 Put the appliance adjacent to a water tap and a water drain 2 Make sure that the dimen sions of the recess agree with the dimensions in the figure 3 Remove the rear screws 1 4 Pull the worktop from behind 2 5 Lift the worktop and move it from the front slots 3 6 Level the appliance using the adjustable feet 7 Install the appliance under the kitchen counter 12 2 Water connection Water inlet hose Connect the inlet hose to a water tap with an external BSP thread spout of 3 4 For best washing performance it is rec ommended to connect the appliance to a cold water supply Energy savings can be made by connect ing the appliance to a Solar water sys tem and using economy options howev er the water temperature must not ex ceed 60 C Inlet water supply e Water pressure 800 kPa max 50 kPa min e Water flow rate 10 L minute min e f water pressure is in excess of 800 kPa a pressure reducing valve should be used Check for leaks e f water temperature is in excess of 60 C a tempering valve should be used Check for leaks IN CAUTION Always use new hoses when you connect the appliance to the wa ter mains Old hoses must not be used The water inlet hose must be examined at an interval of twelve months for deterioration and replaced if necessary The water pressure must be in the limits refer to TECHN
16. quire service for your Appliance 1 In this warranty a acceptable quality as referred to in clause 10 of this warranty has the same meaning referred to in the ACL b ACL means Trade Practices Amendment Australian Consum er Law Act No 2 2010 c Appliance means any AEG product purchased by you ac companied by this document d ASC means AEG authorised serviced centres e AEG is the brand controlled by Electrolux Home Products Pty Ltd of 163 O Riordan Street Mas cot NSW 2020 ABN 51 004 762 341 in respect of Appliances pur chased in Australia and Electro lux NZ Limited of 3 5 Niall Bur gess Road Mount Wellington in respect of Appliances purchased in New Zealand f major failure as referred to in clause 10 of this warranty has the same meaning referred to in the ACL and includes a situation when an Appliance cannot be re paired or it is uneconomic for Electrolux at its discretion to re pair an Appliance during the Warranty Period g Warranty Period means where the Appliance is used for personal domestic or household use i e normal sin gle family use as set out in the instruction manual the Appli ance is warranted against man ufacturing defects in Australia and New Zealand for 60 months following the date of original purchase of the Appli ance this Appliance is not designed for commercial use and there fore no warranty applies
17. r Electrical connection WARNING Risk of fire and electrical shock e The appliance must be earthed e Make sure that the electrical informa tion on the rating plate agrees with ENGLISH 3 the power supply If not contact an electrician e Always use a correctly installed shock proof socket e Do not use multi plug adapters and extension cables e Make sure not to cause damage to the mains plug and to the mains cable Should the mains cable need to be re placed this must be carried out by our Service centre Connect the mains plug to the mains socket only at the end of the installa tion Make sure that there is access to the mains plug after the installation Do not pull the mains cable to discon nect the appliance Always pull the mains plug Do not touch the mains cable or the mains plug with wet hands Test the appliance Run a quick wash ing program and ensure that the ap pliance fills with water washes and drains with no leaks Water connection e Make sure not to cause damage to the water hoses e Before you connect the appliance to new pipes or pipes not used for a long time let the water flow until it is clean e The first time you use the appliance make sure that there is no leakage e The water inlet hose has a safety valve and a sheath with an inner mains ca 7 WARNING Dangerous voltage 4 www aeg com e If the water inlet hose is damaged im mediately di
18. re that the water softener uses the correct quantity of dishwasher salt and water 8 2 Using salt rinse aid and detergent e Only use salt rinse aid and detergent for dishwasher Other products can cause damage to the appliance ENGLISH 13 Important e For better drying results keep the door ajar for some minutes before you remove the dishes e Let the dishes become cold before you remove them from the appliance Hot dishes can be easily damaged e First remove the items from the lower basket then from the upper basket e There can be water on the sides and on the door of the appliance Stainless steel becomes cool more quickly than the dishes The rinse aid helps during the last rinsing phase to dry the dishes with out streaks and stains e Combi detergent tablets contain de tergent rinse aid and other added agents Be sure that these tablets are applicable to the water hardness in your area Refer to the instructions on the packaging of the products e Detergent tablets do not fully dissolve with short programs To prevent de tergent residues on the tableware we recommend that you use the tablets with long programs 2 Do not use more than the correct quantity of detergent Refer to the instructions on the detergent packaging 14 www aeg com 8 3 Loading the baskets i e Only use the appliance to wash items that are dishwasher safe e Do not put in the appliance items made of woo
19. risk while in transit to and from AEG or its ASC Proof of purchase is required before you can make a claim under this war ranty You may not make a claim under this warranty unless the defect claimed is due to faulty or defective parts or workmanship AEG is not liable in the following situations which are not exhaustive a the Appliance is damaged by accident misuse or abuse including fail ure to properly maintain or service normal wear and tear power surges electrical storm damage or incorrect power supply incomplete or improper instal lation incorrect improper or inappro priate operation insect or vermin infestation failure to comply with any ad ditional instructions supplied with the Appliance b the Appliance is modified with out authority from AEG in writ ing c the Appliance s serial number or warranty seal has been removed or defaced d the Appliance was serviced or re paired by anyone other than AEG an authorised repairer or ASC This warranty the contract to which it relates and the relationship be tween you and AEG are governed by the law applicable where the Ap pliance was purchased Where the Appliance was purchased in New Zealand for business purposes the Consumer Guarantee Act does not apply To the extent permitted by law AEG excludes all warranties and liabilities other than as contained in this document including liability for an
20. rs of AUTO PRO ana SILENT start to flash 3 Press Option The indicators of AUTO and SILENT go off The indicator PRO continues to flash e The display shows the current set ting 11 TECHNICAL INFORMATION ENGLISH 17 Od Rinse aid dis penser off id Rinse aid dis penser on Press Option to change the setting Press the on off button to deactivate the appliance and to confirm the set ting Adjust the released quantity of rinse aid Fill the rinse aid dispenser Dimensions Width Height Depth 596 850 610 mm Electrical connection Refer to the rating plate Voltage 220 240 V Frequency 50 Hz Water supply pressure Min max bar MPa 0 5 0 05 8 0 8 Water supply 1 Cold water or hot water max 60 C Capacity Place settings 14 1 Connect the water inlet hose to a water tap with a 3 4 thread 2 If the hot water comes from alternative sources of energy e g solar panels wind turbine energy use the hot water supply to decrease energy consumption 18 www aeg com 12 INSTALLATION 12 1 Fitting under a kitchen counter The plinth of a freestanding appliance is not adjustable Do not remove the appliance worktop if you want to use it as a freestanding unit It is not necessary to remove the work top when installing under a standard kitchen counter Only remove the appliance worktop to install it under a close fitting sink unit or kitchen cou
21. sconnect the mains plug from the mains socket Contact the Service to replace the water inlet hose 1 3 Use e This appliance is intended to be used in household and similar applications such as Farm houses By clients in hotels motels and oth er residential type environments Bed and breakfast type environ ments WARNING Risk of injury burns electrical shock or fire e Do not change the specification of this appliance e Put knives and cutlery with sharp points in the cutlery basket with the points down or in a horizontal posi tion e The appliance can release hot steam if you open the door while a program operates e Do not keep the appliance door open without supervision to prevent to fall on it e Do not sit or stand on the open door e Obey the safety instructions from the manufacturer of the dishwasher deter gent to prevent burns to eyes mouth and throat e Only put detergent in the dispenser before you start a program e Check that the detergent dispenser is empty after completion of the pro gram Do not drink and play with the water in the appliance Do not remove the dishes from the appliance until the program is com pleted There can be detergent on the dishes e Make sure the dispenser is empty after the completion of the program e Do not put flammable products or items that are wet with flammable products in near or on the appliance e Do not use water spra
22. tivate the Multitab option 1 Press Option until the Multitab indi cator comes on If you stop to use the combi detergent tablets before you start to use separately detergent rinse aid and dishwasher salt do these steps 1 Set the water softener to the highest level 2 Make sure that the salt container and the rinse aid dispenser are full 3 Start the shortest program with a rinsing phase without detergent and without dishes 4 Adjust the water softener to the wa ter hardness in your area 5 Adjust the released quantity of rinse aid u Fill the rinse aid dispenser gt Open the water tap 5 Processing residues can stay in the appliance Start a program to remove them Do not use detergent and do not load the baskets 10 www aeg com 6 1 Adjusting the water softener Water hardness Water softener adjustment German French mmol l Clarke Manual Elec degrees degrees degrees tronic dH fH 47 50 84 90 8 4 9 0 58 63 21 10 43 46 76 83 7 6 8 3 53 57 21 9 37 42 65 75 6 5 7 5 46 52 21 8 29 36 51 64 5 1 6 4 36 45 21 7 23 28 40 50 4 0 5 0 28 35 21 6 19 22 33 39 3 3 3 9 23 27 21 51 15 18 26 32 2 6 3 2 18 22 i 11 14 19 25 19 28 13 17 1 3 4 10 7 18 0 7 1 8 5 12 lt 4 lt T lt 0 7 lt 5 12 12 1 Factory position 2 Do not use salt at this level You must adjust the water soft ener manually and electronically
23. to recycle it with the household waste Return the Help protect the environment and product to your local recycling human health and to recycle waste facility or contact your municipal of electrical and electronic office ENGLISH 23 www aeg com shop P Ce es I 117909751 A 052013 C MAN HAEG perfekt in form und funktion
24. y 10 11 12 14 ENGLISH 21 loss or damage whether direct or in direct arising from your purchase use or non use of the Appliance For Appliances and services provi ded by AEG in Australia the Appli ances come with a guarantee by AEG that cannot be excluded under the Australian Consumer Law You are entitled to a replacement or re fund for a major failure and for com pensation for any other reasonably foreseeable loss or damage You are also entitled to have the Appliance repaired or replaced if the Appliance fails to be of acceptable quality and the failure does not amount to a ma jor failure The benefits to you given by this warranty are in addition to your other rights and remedies un der a law in relation to the Applian ces or services to which the warranty relates At all times during the Warranty Peri od AEG shall at its discretion de termine whether repair replacement or refund will apply if an Appliance has a valid warranty claim applicable to it For Appliances and services provi ded by AEG in New Zealand the Appliances come with a guarantee by AEG pursuant to the provisions of the Consumer Guarantees Act the Sale of Goods Act and the Fair Trad ing Act To enquire about claiming under this warranty please follow these steps a carefully check the operating in structions user manual and the terms of this warranty b have the model and serial num ber of the Appliance
25. y and steam to clean the appliance 1 4 Disposal WARNING Risk of injury or suffocation e Disconnect the appliance from the mains supply e Cut off the mains cable and discard it e Remove the door catch to prevent children and pets to get closed in the appliance ENGLISH 5 2 PRODUCT DESCRIPTION NV Z El Worktop EJ Air vent and water hardness dial Top spray arm EJ Rinse aid dispenser Upper spray arm Detergent dispenser Lower spray arm Cutlery basket Filters Lower basket El Rating plate Upper basket Salt container 6 Wwww aeg com 3 CONTROL PANEL Pr Erra Quick Quick AUTO pro SILENT 30Min Eco 50Min 45 70 70 50 60 50 55 auro fero suent son Jeco Dsomn 1 12 gt On off button Delay touchpad Program touchpad Wj Start touchpad Program indicators Indicators Display E Option touchpad Indicators Description 8 Multitab indicator OKO PLUS OKO PLUS indicator ExtraHygiene indicator Washing phase indicator It comes on when the washing phase operates Rinsing phase indicator It comes on when the rinsing phases operate Drying phase indicator It comes on when the drying phase op erates End indicator It comes on when the program is completed Door indicator It comes on when the appliance door is open or is not correctly closed Dela
26. y indicator Rinse aid indicator It is always off while the program operates Salt indicator It is always off while the program operates ENGLISH 7 4 PROGRAMS Program Degree of soil Program Options Type of load phases 1 All Prewash ExtraHygiene AUTO Crockery cutlery Wash 45 C or 70 C OKO PLUS pots and pans Rinses Dry PRO Heavy soil Prewash KO PLUS Crockery cutlery Wash 70 C pots and pans Rinses Dry 3 Normal soil Prewash SILENT Crockery and cut Wash 50 C lery Rinses Dry 30MIN Fresh soil Wash 60 C ExtraHygiene Crockery and cut Rinse lery ECO Normal soil Prewash ExtraHygiene Crockery and cut Wash 50 C OKO PLUS lery Rinses Dry 50MIN Normal soil Wash 55 C ExtraHygiene Crockery and cut Rinses lery Lf 6 Mixed soil Prewash OKO PLUS Crockery cutlery Wash 70 C pots and pans Rinses Dry y Normal or light soil Wash 45 C KO PLUS Delicate crockery Rinses and glassware Dry 1 The appliance senses the degree of soil and the quantity of items in the baskets It automatically adjusts the temperature and quantity of the water the energy consumption and the program duration 2 This program has a high temperature rinsing phase for better hygiene results During the rinsing phase the temperature stays at 70 C for at least 10 minutes 3 This is the most silent program The pump works at a very low speed to decrease the level of noise Because of the low speed
27. you have the following data available The information can be found on the rating plate Model PNC Serial Number A Warning Caution Safety information i General information and tips 9 Environmental information Subject to change without notice 1 A SAFETY INSTRUCTIONS Before the installation and use of the ap pliance carefully read the supplied in structions The manufacturer is not re sponsible if an incorrect installation and use causes injuries and damages Always keep the instructions with the appliance for future reference 1 1 Children and vulnerable people safety WARNING Risk of suffocation injury or per manent disability e Do not let persons children included with reduced physical sensory re duced mental functions or lack of ex perience and knowledge use the ap pliance They must have supervision or instruction for the operation of the ap pliance by a person who is responsible for their safety Do not let children play with the appli ance Keep all packaging away from chil dren Keep all detergents away from chil dren Keep children and pets away from the appliance door when it is open 1 2 Installation e Remove all the packaging e Do not install or use a damaged appli ance e Do not install or use the appliance where the temperature is less than 0 C e Do not drill into the sides of the appli ance otherwise damage to hydraulic and electrical components may occu
Download Pdf Manuals
Related Search