Home

CubeSuite+ Simulator for 78K0R/Kx3 V3.00.03 Release Note

1. Differences between target devices and simulator Differences from behavior of target devices due to simulator specifications Cautions for using simulator GUI Cautions for using the simulator GUI window 5 1 Differences between target devices and simulator 5 1 1 Flash self programming function The following differences exist between the target device and simulator regarding the flash self programming function 1 Operation when a pull down resistor is connected to the FLMDO pin In the target device whether the flash self programming mode can be set via software is determined based on its resistance when a pull down resistor is externally connected to the FLMDO pin FLMDO Pin Handling Setting via Software Pulled down with a resistance of 100k ohm or more Available Pulled down with a resistance of less than 100k ohm Not guaranteed On the other hand in the simulator connection of a pull down resistor to the FLMDO pin can be specified in the I O Panel window but this panel does not have the function to set the resistance value As a result if connection of a pull down resistor to the FLMDO pin is specified it is regarded as an operation equivalent to that being pulled down with a resistance of 100k ohm or more R20UT2511EJ0100 Rev 1 00 Page 6 of 16 February 25 2013 RENESAS CubeSuite Simulator for 78KOR Kx3 V3 00 03 Release Note 2 Errors that are not generated The simulator does not generate the foll
2. o 0 o o 0 JosTS2 OSTS1 OSTSO NN 4 477 Bits are always 0 Although the values of these bits cannot be changed in the case of the target device the values can be changed in the case of the simulator Note that changing these values has no effect on behavior 5 1 15 Comparator stabilization time of A D converter The comparator stabilization times of the A D converter are different for the target device and simulator Target device It takes 1 microsecond from the start of operation of the comparator until it stabilizes Any A D conversion results obtained before stabilization will be invalid For this reason it is necessary to ignore the first A D conversion results Simulator Comparator operation stabilizes immediately upon startup For this reason A D conversion results obtained within 1 microsecond of the start of operation will be correct and there is thus no need to ignore the first A D conversion results 5 1 16 Default voltage of AVrero pin and AVrer pin Default voltage of AVrero pin is 5 0V And default voltage of AVrer pin is 3 6V Note The meaning of Default voltage is the voltage when the pin have no connection R20UT2511EJ0100 Rev 1 00 Page 13 of 16 February 25 2013 RENESAS CubeSuite Simulator for 78KOR Kx3 V3 00 03 Release Note 5 1 17 Interrupt response time The interrupt response times of the target device and simulator differ Target device It takes 9 to 14 clock cycles from the
3. for external interrupt pin ssssssesesssssesrnrrersstetrrrnrensssrstttnnrnnsrtnntrnn nennen ent 10 9 16 C DUS SIMULATION ercana e CE E E E 10 5 1 7 External bus interface fUNCtiOns c cece etter ee erne ee erent ee ttnt t tunnt EEEn AE EEEn AE EEANN EEES AE EEEn aE EEEn nE EEEn ae 11 SLO DMA TONTE onenn a E T R N ETE T O 12 5 1 9 Operation clock of timer array Unit esseenid A R A 12 5 1 10 Input pulse interval measurement mode of timer array unit eccececeeeeeeeeceeeeeeeseteeeseaeees 12 9 171 Noise filter of timer array Unilecsencseariserairarniironi E E a 12 5 1 12 Operation clock of serial array unit 0 0 eee ee eeeeee erent etree ee eerie eee e teaser tieeeee teaser taeeeeetaa 12 5 1 13 Noise filter of serial array Unit ccccccceecceseececctesseceeesseeceeeensecceetesseceeeesaeceeeesececseeseceeeteneceeeeeenes 13 9 I4 SER OF CONSTANE Dil es cevswicceveninczenyitcaceybvencseyvepleneyapencceeyt EAA 13 5 1 15 Comparator stabilization time of A D converter 2 00 2 cececeeeeececeeeeeeeeeeeaeceeeeeeeeeecenaeeeeeeeeesessnaeess 13 5 1 16 Default voltage of AVrero PIN ANd AV per PIN 2 ceecceccceceeeeeeneececeeeeeseeeeeaeceeeeeeeesecennieaeeeeeeesseneaeees 13 5 1 17 Interrupt response tiIMe ceccecececeeeee cece cece eeceeeeeeeeeeeeescaaeaeeeeecesescaacaeeeeeeeseesnceeeeeeeeeeesetensaees 14 5 1 18 Execution of illegal inStrUCtionS 0 cece eee e etter ee enne ee eee E EEE E EERE 14 5 2 Cauti
4. is used to set the oscillator gain according to the frequency when oscillating the high speed system clock If a wrong setting is made the high speed system clock may not oscillate in the target device In the simulator however wrong settings do not affect the oscillation of the high speed system clock Bit 0 FSEL of operation speed mode control register OSMC This register is used to control the step up circuit for the high speed flash memory operation If a wrong setting is made read or instruction fetch from the flash memory may fail or self programming may fail in the target device In the simulator however wrong settings do not affect the operation High speed internal oscillator trimming register HIOTRM This register is used to correct the high speed internal oscillator accuracy This register is provided in the target device because the high speed internal oscillator usually causes errors In the simulator however the high speed internal oscillator does not cause errors so it is not simulated R20UT2511EJ0100 Rev 1 00 Page 9 of 16 February 25 2013 RENESAS CubeSuite Simulator for 78KOR Kx3 V3 00 03 Release Note 5 1 5 Noise reduction circuit for external interrupt pin The simulator does not simulate the noise reduction circuit For example if you input the active level to an external interrupt pin with a noise reduction circuit the interrupt will be received even if the active level amplitude is too low The exa
5. signal input to external bus pins in the Timing Chart window It will appear as high impedance When connecting ROM or RAM to the external bus perform configuration in the Property panel from the Debugging Tool Setting tab Connect by entering Type of memory to connect to emulation ROM area or emulation RAM area Memory address to connect to Property S 78KOR Simulator Property This setting enables both E Memory 8 Writing to external bus E Access Memory While Running Update display during the execution Yes i Reading from external bus Display update interval ms 500 Memory mappings For the addition and e in start address or end address select the button and r pping dialog box The additions deletibrs M RAM area target memory area and 1 0 protection area are not possi Connect Settings Debug Tool Settings A Download File Settings Hook Transaction Set Memory Mapping Memory type Address range Emulation ROM area Me Ox80000 HE _Oxedfff Memory type 7 range Internal ROM area 0x00000 Ox7ffff 512 Non map area 0x80000 Oxeffff 446 SFR area ox 0000 OxfO7ff 2 KBytes 8 bits Non map area Ox 0800 Oxf0ffft 2 KBytes 8 bits Mirror area Ox 1000 Oxf66ff 30464 Bytes 16 bits Internal RAM area Oxf8700 Oxffedf 30688 Bytes 16 bits Register area Oxffeed Oxffeff 32 Bytes 16 bits SFR area Oxftfftoo Oxfffff 256 Bytes 8 bits OK Cancel Help R20UT2511EJ0100 Rev 1 00 Page 11 of 16 Feb
6. 1 905 898 5441 Fax 1 905 898 3220 Renesas Electronics Europe Limited Dukes Meadow Millboard Road Bourne End Buckinghamshire SL8 5FH U K Tel 44 1628 651 700 Fax 44 1628 651 804 Renesas Electronics Europe GmbH Arcadiastrasse 10 40472 Dusseldorf Germany Tel 49 211 65030 Fax 49 211 6503 1327 Renesas Electronics China Co Ltd 7th Floor Quantum Plaza No 27 ZhiChunLu Haidian District Beijing 100083 P R China Tel 86 10 8235 1155 Fax 86 10 8235 7679 Renesas Electronics Shanghai Co Lid a f i Unit 204 205 AZIA Center No 1233 Lujiazui Ring Rd Pudong District Shanghai 200120 China Tel 86 21 5877 1818 Fax 86 21 6887 7858 7898 Renesas Electronics Hong Kong Limited Unit 1601 1613 16 F Tower 2 Grand Century Place 193 Prince Edward Road West Mongkok Kowloon Hong Kong Tel 852 2886 9318 Fax 852 2886 9022 9044 Renesas Electronics Taiwan Co Ltd 13F No 363 Fu Shing North Road Taipei Taiwan Tel 886 2 8175 9600 Fax 886 2 8175 9670 Renesas Electronics Singapore Pte Ltd 80 Bendemeer Road Unit 06 02 Hyflux Innovation Centre Singapore 339949 Tel 65 6213 0200 Fax 65 6213 0300 Renesas Electronics Malaysia Sdn Bhd Unit 906 Block B Menara Amcorp Amcorp Trade Centre No 18 Jin Persiaran Barat 46050 Petaling Jaya Selangor Darul Ehsan Malaysia Tel 60 3 7955 9390 Fax 60 3 7955 9510 Renesas Electronics Korea Co Ltd 11F Samik Lavied or Bldg 720 2 Yeoksam Dong Kan
7. 68A yPD78F 1174 uPD78F1175 uPD78F 1176 uPD78F 1177 uPD78F 1178 78KOR KH3 uPD78F1174A uPD78F1175A uPD78F1176A uPD78F1177A uPD78F1178A 78KOR KJ3_ UPD78F1184A uPD78F1185A uPD78F1186A uPD78F1187A uPD78F1188A R20UT2511EJ0100 Rev 1 00 Page 2 of 16 February 25 2013 RENESAS CubeSuite Simulator for 78KOR Kx3 V3 00 03 Release Note Chapter 2 User s Manuals Please read the following user s manuals together with this document Manual Name Document Number CubeSuite V1 01 00 78KOR Debug R20UT0732EJ0100 CubeSuite V2 00 00 Message R20UT2448EJ0100 R20UT2511EJ0100 Rev 1 00 Page 3 of 16 February 25 2013 RENESAS CubeSuite Simulator for 78KOR Kx3 V3 00 03 Release Note Chapter 3 Key Word for Uninstallation To uninstall this product use the integrated uninstaller uninstalls CubeSuite R20UT2511EJ0100 Rev 1 00 Page 4 of 16 February 25 2013 RENESAS CubeSuite Simulator for 78KOR Kx3 V3 00 03 Release Note Chapter 4 Changes This chapter describes changes from V3 00 02 to V3 00 03 4 1 Specifications changed 4 1 1 Simulation on CubeSuite V2 00 00 Support simulation on CubeSuite V2 00 00 There is no functional change R20UT2511EJ0100 Rev 1 00 Page 5 of 16 February 25 2013 RENESAS CubeSuite Simulator for 78KOR Kx3 V3 00 03 Release Note Chapter 5 Cautions This section describes cautions for using 78KOR Kx3 simulator The following two types of caution are described
8. CRmn timer counter register mn 00 07 or 10 13 is to OxFFFF For this reason the pulse width count will be one less than on the target device 5 1 11 Noise filter of timer array unit Although the target device s timer array unit has a function to turn the noise filter on and off in order to reduce noise on the timer input pin the simulator does not simulate this There is no difference in behavior whether filtering is on or off Since there is no noise in the simulator s signal it would be meaningless to simulate this function 5 1 12 Operation clock of serial array unit Do not use INTTM02 or INTTMO3 as the operation clock for the serial array unit Doing so will prevent the serial array unit from operating at all R20UT2511EJ0100 Rev 1 00 Page 12 of 16 February 25 2013 RENESAS CubeSuite Simulator for 78KOR Kx3 V3 00 03 Release Note 5 1 13 Noise filter of serial array unit Although the target device s serial array unit has a function to turn the noise filter on and off in order to reduce noise on the input pin the simulator does not simulate this There is no difference in behavior whether filtering is on or off Since there is no noise in the simulator s signal it would be meaningless to simulate this function 5 1 14 SFR 0 1 constant bit The SFR has bits that are always 0 or 1 For example bits 3 to 7 are always 0 for the oscillation stabilization time selection register OSTS 7 6 5 4 3 2 1 0 osts
9. RENESAS CubeSuite Simulator for 78KOR Kx3 V3 00 03 R20UT2511EJ0100 Rev 1 00 Release Note February 25 2013 Contents Chapter 1 Target Devices 0 0 2 ecceeeeeeeee ee eeee ee ee eeneee ee eaeee ees aeeeeeseeeeeeseeaeeeseeeeaeeeeeeeaeeeseeeaeeeseeaeeeseenaeees 2 Chapter 2 User s Manuals 0 cccccceceeececceeeeeeeeeeeaeceeeeeeececsaaaeceeeeeeesecaaaeceeeeeeeeseseccasaeeseeeesesecsieaeeeeeess 3 Chapter 3 Key Word for Uninstallation 0 ec ccecceeceeeeeeeeeeeeeeeeeeeeeeeeeeeeseeeaeeeseneaeeeseeeaeeeseeeaeeesenaeeeteeaeees 4 Chapter Changos scanneri a a a et Aaglagetea dia etd Avettiaeatt bettas 5 4 1 SPECiications changed cerien a cers dune caevedenccbbagehsettedda cers dnidi Gtiseheetveds ccrsage esis 5 4 1 1 Simulation on CubeSuite V2 00 00 eceeeeeee ee aiaia a 5 Chapter 5 Cautions cciievtiitre ide n sie ede i vie he EE adeeb de aie adds 6 5 1 Differences between target devices and simulator 0 0 0 cece ee eene eter ener eter tees ee taeeeeetaeeeeetnaeeeeees 6 5 1 1 Flash self programming fUnCtiOn 1 ccccccccecaecscecectssacccatsssecectssacceatenecectetscccetenseceenessdcecteneceetinecees 6 2 PROS nonen e na vague sah nased a a a a a Ea 7 5 1 3 Oscillation stabilization time of Clock Generator sssssesesesssrreserresrtrrssttrnssttnnsstennnsttnnnstennssnn ns 8 5 1 4 SFR with clock generator AMPH FSEL HIOTRM essssesssssssrisseerrssesrrssrrrrssrinrssrtrnnsrennsstrnsssnns 9 5 1 5 Noise reduction circuit
10. cluding but not limited to redundancy fire control and malfunction prevention appropriate treatment for aging degradation or any other appropriate measures Because the evaluation of microcomputer software alone is very difficult please evaluate the safety of the final products or systems manufactured by you 8 Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product Please use Renesas Electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances including without limitation the EU RoHS Directive Renesas Electronics assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations 9 Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture use or sale is prohibited under any applicable domestic or foreign laws or regulations You should not use Renesas Electronics products or technology described in this document for any purpose relating to military applications or use by the military including but not limited to the development of weapons of mass destruction When exporting the Renesas Electronics products or technology described in this document you should comply with the applicable export control laws and regulations and follow the procedures r
11. eck the quality grade of each Renesas Electronics product before using it in a particular application You may not use any Renesas Electronics product for any application for which it is not intended Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for which the product is not intended by Renesas Electronics 6 You should use the Renesas Electronics products described in this document within the range specified by Renesas Electronics especially with respect to the maximum rating operating supply voltage range movement power voltage range heat radiation characteristics installation and other product characteristics Renesas Electronics shall have no liability for malfunctions or damages arising out of the use of Renesas Electronics products beyond such specified ranges 7 Although Renesas Electronics endeavors to improve the quality and reliability of its products semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions Further Renesas Electronics products are not subject to radiation resistance design Please be sure to implement safety measures to guard them against the possibility of physical injury and injury or damage caused by fire in the event of the failure of a Renesas Electronics product such as safety design for hardware and software in
12. equired by such laws and regulations 10 It is the responsibility of the buyer or distributor of Renesas Electronics products who distributes disposes of or otherwise places the product with a third party to notify such third party in advance of the contents and conditions set forth in this document Renesas Electronics assumes no responsibility for any losses incurred by you or third parties as a result of unauthorized use of Renesas Electronics products 11 This document may not be reproduced or duplicated in any form in whole or in part without prior written consent of Renesas Electronics 12 Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this document or Renesas Electronics products or if you have any other inquiries Note 1 Renesas Electronics as used in this document means Renesas Electronics Corporation and also includes its majority owned subsidiaries Note 2 Renesas Electronics product s means any product developed or manufactured by or for Renesas Electronics sCENESAS SALES OFFICES Renesas Electronics Corporation http www renesas com Refer to http www renesas com for the latest and detailed information Renesas Electronics America Inc 2880 Scott Boulevard Santa Clara CA 95050 2554 U S A Tel 1 408 588 6000 Fax 1 408 588 6130 Renesas Electronics Canada Limited _ 1101 Nicholson Road Newmarket Ontario L3Y 9C3 Canada Tel
13. generation of an interrupt until actual vector interrupt processing begins Simulator Vector interrupt processing begins immediately upon the interrupt 5 1 18 Execution of illegal instructions If an illegal instruction instruction code OxFF is executed the target device will be reset but the simulator will go into an infinite loop the illegal instruction will be executed repeatedly R20UT2511EJ0100 Rev 1 00 Page 14 of 16 February 25 2013 RENESAS CubeSuite Simulator for 78KOR Kx3 V3 00 03 Release Note 5 2 Cautions for using simulator GUI 5 2 1 Cautions for controlling each windows The following keyboard operations are not available in the simulator windows signal data editor window I O panel window and serial window Navigation via tab or arrow keys lt ft Deletion via the Del or Backspace keys Copy amp paste and other operations via the Ctrl C V X A or Z keys Perform the above operations as follows Navigation Navigate using the mouse Deletion Right click and perform the action via the context menu Copy amp paste etc Right click and perform the action via the context menu 5 2 2 Cautions for closing simulator GUI window The simulator GUI window can only be closed by disconnecting from the debugging tool or by closing CubeSuite proper The X button cannot be clicked Additionally although it appears that the X button can be pre
14. gnam Ku Seoul 135 080 Korea Tel 82 2 558 3737 Fax 82 2 558 5141 2013 Renesas Electronics Corporation and Renesas Solutions Corp Colophon 22
15. level the simulator momentarily goes into reset status and then the reset status is released immediately R20UT2511EJ0100 Rev 1 00 February 25 2013 RENESAS Page 7 of 16 CubeSuite Simulator for 78KOR Kx3 V3 00 03 Release Note 5 1 3 Oscillation stabilization time of Clock Generator The simulator does not simulate the clock oscillator oscillation stabilization time The oscillation stabilization time is always 0 seconds when a reset or standby is released regardless of the OSTS register settings The OSTS register is set to the following values e Initial value after reset during STOP mode when MSTOP of CSC register 1 0x00 e MSTOP of CSC register 0 after STOP mode release Values shown in the following table Maximum value in the target device OSTS Setting Value OSTC Value 0x0 2 fx 0x1 2 fx 0x2 2 fx 0x3 2 fx 0x4 2 fx 0x5 2 fx Ox6 2 fx 0x7 2 8 fx The following figure illustrates this operation In the target device the X1 clock oscillation starts after the states 1 to 4 have passed In the simulator states 1 to 4 end instantly and the X1 clock oscillation starts In target device an example of when OSTS is set to 0x07 sx MUU UU QUO ULL waveform In simulator an example of when OSTS is set to 0x07 oscillation waveform R20UT2511EJ0100 Rev 1 00 Page 8 of 16 February 25 2013 RENESAS CubeSuite Sim
16. license express implied or otherwise is granted hereby under any patents copyrights or other intellectual property rights of Renesas Electronics or others 4 You should not alter modify copy or otherwise misappropriate any Renesas Electronics product whether in whole or in part Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from such alteration modification copy or otherwise misappropriation of Renesas Electronics product 5 Renesas Electronics products are classified according to the following two quality grades Standard and High Quality The recommended applications for each Renesas Electronics product depends on the product s quality grade as indicated below Standard Computers office equipment communications equipment test and measurement equipment audio and visual equipment home electronic appliances machine tools personal electronic equipment and industrial robots etc High Quality Transportation equipment automobiles trains ships etc traffic control systems anti disaster systems anti crime systems and safety equipment etc Renesas Electronics products are neither intended nor authorized for use in products or systems that may pose a direct threat to human life or bodily injury artificial life support devices or systems surgical implantations etc or may cause serious property damages nuclear reactor control systems military equipment etc You must ch
17. mple below considers the case when there is input to the INTPO pin There is a noise reduction circuit on the INTPO pin of the target device For this reason in order to generate an interrupt it is necessary to input an effective edge to the target device and subsequently maintain the signal level See the user s manual of the target device for the length of time it must be maintained Target device behavior falling effective edge Signal input to INTPO pin In the case of the simulator however this noise reduction circuit is not simulated For this reason an interrupt will be generated any time a valid edge is generated No need to maintain signal level Simulator behavior falling effective edge Signal input to INTPO pin q B 5 1 6 IIC bus simulation IIC bus simulation is not supported R20UT2511EJ0100 Rev 1 00 Page 10 of 16 February 25 2013 RENESAS CubeSuite Simulator for 78KOR Kx3 V3 00 03 Release Note 5 1 7 External bus interface functions Some of the external bus interface functions can be simulated and some cannot Functions that can be simulated ROM and RAM connection Access to connected ROM RAM Functions that cannot be simulated External bus related SFR simulation External bus access is possible even without configuring SFR Access speed simulation Access time is always 0 clock cycles Additionally signal input to the WAIT pin is ignored Check
18. ons for using simulator GUI eee cece eee eene ee ee eae teen tratt ee eeeaaeeeeeeaaeeeeeeaaeeeeesaeeeeeenaeeeeeeeaas 15 5 2 1 Cautions for controlling each WINKOWS cceceeteeeee ee ette ee ee etnies ee tender taeee erties ee teaser NEREA R RARE 15 5 2 2 Cautions for closing simulator GUI WINdOW sessies eeeeee eee ee ee tne eset teaser teeeee teases ENNAN 15 5 2 3 Cautions for showing help for the simulator GUI WINGOW ec eieeeeeeeeeteeeeeetteeeeettteeeeeeeneeeeeene 15 5 2 4 Cautions for disconnecting the debug tool eee centre treet eee eenneee eee tneeeeeeeeeeetieeeersneeeerena 15 5 2 5 Cautions for setting the Host Machine s language and region eceeeeeceteeeeeeeteeeeeeeteeeeetnteeeeeeeee 16 R20UT2511EJ0100 Rev 1 00 Page 1 of 16 February 25 2013 RENESAS CubeSuite Simulator for 78KOR Kx3 V3 00 03 Release Note Chapter 1 Target Devices Below is a list of devices supported by the 78KOR Kx3 simulator Nickname Device name yPD78F 1142 uPD78F 1143 uPD78F 1144 uPD78F 1145 uPD78F 1146 78KOR KE3 UPD78F1142A uPD78F1143A uPD78F1144A uPD78F1145A uPD78F1146A UPD78F 1152 uPD78F1153 uPD78F 1154 uPD78F 1155 uPD78F 1156 78KOR KF3 uUPD78F1152A uPD78F1153A uPD78F1154A uPD78F1155A uPD78F1156A UPD78F 1162 uPD78F1163 uPD78F 1164 uPD78F 1165 uPD78F 1166 yPD78F 1167 uPD78F 1168 78KOR KG3 UPD78F1162A uUPD78F1163A uPD78F1164A uPD78F1165A uPD78F1166A uPD78F1167A uPD78F11
19. owing errors Error Function Name Error Name Return value Initialize function Processing abortion due to interrupt occurrence Ox1F Block blank check function Processing abortion due to interrupt occurrence 0x1F Block erase function Erase eror O aad 0x1A Processing abortion due to interrupt occurrence 0x1F Word write function Write error o O L 0 x1C il Processing abortion due to interrupt occurrence Ox1F Block verify function Verify internal verify error LS Ox1B_ Processing abortion due to interrupt occurrence 0x1F Set information function Erase eror O OO fOOa Ld 0x1A Verify internal verify error LS 0x1B_____ Write Smor ee cee ee EOE ee eeen d Ox1C Processing abortion due to interrupt occurrence Ox1F EEPROM write function Write error 0x1C Verify internal verify error 2222222222222222 d Ox1D_ Processing abortion due to interrupt occurrence 0x1F 5 1 2 Reset If a reset is generated by the Power on Clear circuit POC or low voltage detector LVI circuit the simulator will display STANDBY in the status bar The status is actually reset not standby And the behavior differs as follows if a reset is generated by the RESET pin Target device Goes into reset status when the RESET pin goes to low level Reset status is released when it goes to high level Simulator Does not go into reset status when the RESET pin goes to low level When it goes to high
20. ruary 25 2013 RENESAS CubeSuite Simulator for 78KOR Kx3 V3 00 03 Release Note 5 1 8 DMA controller The transfer speeds of the target device and simulator differ as follows when simulating the DMA controller Target device It takes two clock cycles to complete one DMA transfer The CPU waits during this period If there is contention for transfer timing with another channel s DMA then one of the DMA transfers will be placed on hold after the other DMA transfer is completed the one on hold will begin Simulator It takes zero clock cycles to complete one DMA transfer For this reason the CPU does not wait If there is contention for transfer timing with another channel s DMA then both of the DMA transfers are performed simultaneously 5 1 9 Operation clock of timer array unit Do not specify an operation clock that is 233 Hz or lower If the operation clock CKmk of the timer array unit m 0 or 1 k 0 or 1 is 233 Hz or lower then the timer array unit will not operate correctly it will behave as if operating via a clock that is faster than the one selected 5 1 10 Input pulse interval measurement mode of timer array unit When the input pulse interval measurement mode of the timer array unit is being used the behavior when an effective edge is detected on the Timn mn 00 07 or 10 13 pin differs Target device The TCRmn timer counter register mn 00 07 or 10 13 is initialized to Ox0000 Simulator The T
21. ssed if Aero is enabled in Windows Vista pressing this button will not close the GUI window 5 2 3 Cautions for showing help for the simulator GUI window Pressing the F1 key in the simulator GUI window will not display the help if none of the internal windows are visible e g the I O panel window To display the help for the simulator GUI window from the GUI window s menu select Help gt Main Window 5 2 4 Cautions for disconnecting the debug tool CubeSuite may exit if the debugging tool is disconnected while any of the following dialog boxes is open from the simulator GUI window Make sure that the following dialog boxes are closed before disconnecting the debugging tool Save As Parts Button Properties Open eAnalog Button Properties New Parts Key Properties Color Parts Level Gauge Properties Font Parts Led Properties Customize Parts Segment LED Properties Loop Parts Matrix Led Properties Select Pin Parts Buzzer Properties Search Data ePull up Pull down Format UART Entry Bitmap Format CSI Object Properties Message e g Error R20UT2511EJ0100 Rev 1 00 Page 15 of 16 February 25 2013 RENESAS CubeSuite Simulator for 78KOR Kx3 V3 00 03 Release Note 5 2 5 Cautions for setting the Host Machine s language and region If a Japanese OS is installed on your Host Machine then if the language or region is set to other than Japanese Japan the menus and dialog box names of the simulator GUI window
22. ulator for 78KOR Kx3 V3 00 03 Release Note Therefore pay attention to the code that waits for oscillation stabilization There is no problem if a program is created with the condition that the execution exits the oscillation stabilization wait period when the OSTC register value becomes the maximum value or when the OSTC register value exceeds the specified value but if a program is created with the condition that the execution exits the oscillation stabilization wait period when the OSTC register value becomes a value other than the maximum value the execution enters an infinite loop The following shows examples of code that causes does not cause problems This is an example of when OSTS is set to 0x07 Correct program example 1 Correct program example 2 Example of program that may cause problems while OSTC Oxff while OSTC lt Oxf0 while OSTC Oxf0 NOP wait NOP wait NOP wait 5 1 4 SFR with clock generator AMPH FSEL HIOTRM The simulator does not simulate the following SFRs which belong to the clock generator Read write for each register can be performed normally but the operation does not change even if its value is changed e Bit 0 AMPH of clock operation mode control register CMC e Bit 0 FSEL of operation speed mode control register OSMC e High speed internal oscillator trimming register HIOTRM Bit 0 AMPH of clock operation mode control register CMC This register
23. will be shown in English Similarly if a non Japanese OS is installed on your Host Machine then if the language or region is set to Japanese Japan the menus and dialog box names of the simulator GUI window will be shown in Japanese All trademarks and registered trademarks are the property of their respective owners R20UT2511EJ0100 Rev 1 00 Page 16 of 16 February 25 2013 RENESAS Notice 1 Descriptions of circuits software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples You are fully responsible for the incorporation of these circuits software and information in the design of your equipment Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits software or information 2 Renesas Electronics has used reasonable care in preparing the information included in this document but Renesas Electronics does not warrant that such information is error free Renesas Electronics assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein 3 Renesas Electronics does not assume any liability for infringement of patents copyrights or other intellectual property rights of third parties by or arising from the use of Renesas Electronics products or technical information described in this document No

CubeSuite+ Simulator for 78K0R/Kx3 V3.00.03 Release Note

Contents

Download Pdf Manuals

Related Search

Related Contents