User Manual
Contents
1. STSM212 MONITOR SCREEN 5 0 inch 128mm VIEWING ANGLE POWER CONSUMPTION POWER SOURCE TV SYSTEM VIDEO INPUT OUTPUT RESOLUTION CONTRAST BRIGHTNESS OPERATING TEMPERATURE STORAGE TEMPERATURE WEIGHT OUTER DIMENSIONS WxHxD DISCLAIMER CMOS 1 3 OV7949 NTSC 510 H x 496 V PAL 626 H x 586 V NTSC 0 232x0 165in 5 9mm x 4 2mm 1 3 inch INTERNAL 380 TV LINES 0 LUX MINIMUM F 1 2 MINIMUM 48dB AT AGC OFF 9V 12Vdc 1 5W AT 12Vdc MAX 150mA 110 D 98 H 82 V 4 F to 149 F 20 C to 65 C 22 F to 176 F 30 C to 80 C 400g 0 88Ib 3 54 x 2 76 x 3 39in 90 x 70 x 86mm COLOR TFT LCD 50 LEFT RIGHT 15 TOP 35 DOWN 10W 560mA MAXIMUM 12 28Vde PAL NTSC COMPOSITE VIDEO SINGLE 1VP P 75 OHM 960 H x 234 V 350 1 200cd m2 14 F to 140 F 10 C to 60 C 13 F to 176 F 25 C to 80 C 330g 0 728Ib 5 67 x 4 88 x1 06in 144 x 124 x 27mm without flush mount The use of the STSK5665 Vehicle CCTV system should not in any way be used as a substitute for careful and cautious driving Always obey traffic laws and motor safety regulations must always be adhered to Specifications subject to change without any notice Fig 1 Camera mount in suggested location Mount camera assembly high Centered Camera mounting hole pattern 60 30 THRU Fig 2 Position of camera Vehicles behind truck Street Rear Bumper Typical mon2. in any way to be a substitute for careful and cautious driving All applicable traffic laws and motor vehicle safety regulations must still be obeyed FEATURES STSC108 CAMERA CMOS Camera e lt 1 Lux sensitivity 18 IR LED Field of view 110 Diagonal e Back Light Compensation BLC e Automatic electronic iris provides a clearer more consistent image in low and bright light Compact and lightweight design installs easily into most vehicles e Waterproof dustproof IP69 rating e Wind deflector reduces buildup of dirt on lens STSM212 TFT LCD COLOR 5 MONITOR e Menu Control for Picture System and Options One Camera e Power stand by switch e Powerful built in speaker Day Night Mode CONTENTS OF COMPLETE SYSTEM 1 Camera with Accessories Mounting Bracket w hardware Wind Deflector 65 Camera extension cable 1 Monitor with Accessories Duckfoot universal bracket for surface mounting of monitor on dashboard or headliner including adhesive pad Power Video Audio Distribution harness INSTALLATION INSTRUCTIONS Note The following instructions are for typical rear view application STSC108 CAMERA 1 2 Attach camera bracket close to rear marker lights centered on vehicle see Fig 1 Attachment point must be sturdy enough to support camera and bracket We do not recommend mounting the camera near the lower area of the vehicle ex bumper This reduces the view of the camera
3. possible into vehicle and clamp securely This reduces the possibility of it being hooked or snagged Keep all cables away from HOT ROTATING and ELECTRICALLY NOISY components Camera Drill a 20mm 0 8in diameter hole into vehicle body near the camera and bracket Insert camera cable into vehicle be careful not to kink cable and fit grommet into hole Apply sealant around grommet to increase resistance to water penetration Connect camera to the camera extension cable which runs inside the vehicle Monitor The monitor terminates in a 13 pin connector which should be connected to the mating 13 pin receptacle end of the power video audio distribution harness For typical rear view installation connect the camera extension cable from the rear view camera to the 4 pin connector The green wire is the REVERSE trigger wire In typical rear view installations connecting this wire to the vehicle s backup light circuit will activate the rear view image whenever the vehicle shifts into reverse FUEL TANKERS amp OTHER SPECIALTY VEHICLES All electrical equipment fitted to petroleum vehicles must be connected via battery master switch and must be isolated from the battery while the vehicle are loading and unloading For other specialty vehicles please check applicable code and regulations prior to installation 10 Always consult your dealer when fitting any electrical or electronic equipment to a vehicle fitted with a CAN bus or mult
4. COLOR BACKUP CAMERA SYSTEM STSK5665 VisionSystems A Century of Automotive Vision Safety WARNING 1 To prevent electrical shock DO NOT OPEN THE MONITOR CASE There are dangerous voltages inside the monitor There are no user serviceable parts inside 2 Avoid exposing monitor to water rain moisture etc It is NOT waterproof Any moisture inside the monitor could cause extensive damage 3 Do not disassemble the camera This voids the warranty Disassembling the camera will compromise the waterproof seal STORAGE 1 Do not expose the monitor to excessive heat or cold The storage temperature of this machine is 13 F to 176 F and operating temperature is 14 F to 140 F 2 Do not store or operate in humid environments e GENERAL 1 This system is intended for use in automotive applications Power source should be an automobile storage battery 12V 24V 2 Make sure all cables are connected properly Improper cable connections may damage the monitor Remove the cable connection when you do not intend to use the unit for a long period of time 3 Please install this system according to the instructions in this manual 4 Connect the system to an ignition switched power source Connection to an unswitched battery source will reduce battery life This device complies with Part 15 of the FCC Rules Operation is C subject to the following two conditions 1 This device may not cause harmful interference 2 Th
5. and increases the chance of physical damage to the camera Attach camera to bracket using screws provided Adjust angle as indicated in Fig 2 Use rear bumper and back of vehicle as a reference point Wind deflector may be installed This deflector is designed to reduce the buildup of dust dirt and moisture on the camera lens See Fig 3 STSM212 MONITOR 1 Attach monitor inside vehicle in a location convenient to the driver ex center of dash overhead or flush mounted in dash 2 Attach the duckfoot bracket to the dashboard or to the headliner using self tapping screws and or adhesive pad 3 Fasten monitor to duckfoot and adjust mounting angle to allow optimum driver viewing comfort See Fig 4 CABLE 1 Be sure to position the cable properly The male end attaches to the camera The female end attaches to the power video audio distribution harness typically located under the dashboard See Fig 5 2 Donotrun the cable over sharp edges or corners Do not kink the cable Keep the cable away from hot and rotating parts 3 Fasten all cable runs and secure all excess cable WIRING CAMERA AND MONITOR Connect the red wire to an ignition switched accessory ex radio power source and connect the black wire to chassis ground See wiring diagram for connections See Fig 5 Before drilling be sure no cable or wire is on the other side Be sure to drill a 20mm 0 8in diameter hole only Feed as much cable as
6. iplex system FUNCTIONS AND OPERATION MONITOR 1 MINI SWITCHES Both mini switches activate the mirror function for the Camera 2 POWER If the monitor is switched off press the Power switch to switch the monitor on the picture appears Test if the mirror function is correctly set The setting should be such that an obstacle behind the vehicle on the right also appears on the right in the monitor Press the main switch Power to switch off the monitor The picture disappears 3 VOLUME You can set the volume to amplify or mute the noises transmitted by the camera Press the button to reduce the volume Press the button to increase the volume 4 MENU Button See Press the MENU button once to set desired brightness Press the MENU button twice to set desired contrast Press the MENU button three times to set desired color 5 MODE Switching the monitor to day mode or night mode When in night mode the monitor darkens the image on the monitor to prevent glaring light that can distract the driver Press the main switch MODE The monitor is switched from day mode to night mode or vice versa The LED COLOR is lit orange if the monitor is operating in day mode The LED COLOR is lit green if the monitor is operating in night mode HOW TO SET YOUR MONITOR TO YOUR REQUIREMENTS NOTE On screen menu commands may only be selected when monitor is in Steady on green light mode When m
7. is device must accept any interference received including interference that may cause undesired operation E 1 3 1 High voltages exist within the monitor Opening of monitor case is unsafe and never necessary for operating purposes 2 In case of any failure please tum off the display at once and notify our company or the corresponding dealer The monitor and camera are made up of many precise electronic components Any disassembly or modification may lead to damage and voiding of warranty Front view 1 2 3 4 5 6 7 8 Mini Switches Turns mirror function on and off for Camera 1 Reduces the brightness to prevent glare Switching the monitor to day mode or night mode Menu Switches to setup mode See p 8 for options Volume amp Menu Control Increases amp Decreases Volume amp Adjust Menu settings Brightness Control Contrast Control Color Indicates dimming status amp Tint Control LED is lit orange if the monitor is operating in day mode green if night Power Switch Switches Monitor from Stand by to Steady on COLOR BACKUP CAMERA SYSTEM STSK5665 INTRODUCTION Please read this manual thoroughly This manual contains instructions to make the installation of the camera and monitor easier The color backup camera system is a supplement to standard rear view mirror systems and will provide additional rear view vision when installed and maintained properly It is not intended
8. itor image of view from properly installed camera 11 Fig 3 Optional wind deflector 12 Fig 4 POWER INPUT LEAD RED To Ignition Switched Accessory a ni GROUND WIRE BLACK To metal point of the vehicle CAM1 l REVERSE Trigger 1 GREEN O Note For typical installation this trigger wire should be connected to the vehicle s back up lights circuit and the rear view camera should be attached to the connector as shown 14 ROSCO QUALITY POLICY Rosco Vision Systems is committed to providing customer satisfaction and quality products supported by employee participation and continuous improvement through the Quality Management System Vision Systems 90 21 144th Place Jamaica New York 11435 Phone 1 800 227 2095 Fax 718 297 0323 www roscomirrors com ACentury of Automotive Vision Safety
9. onitor is in standby mode and activated by trigger sig nal on screen menu commands are disabled To set monitor to suit your requirements proceed as follows Press the MENU button once to set the desired brightness The LED BRI starts flashing Press the button to reduce the brightness Press the button to increase the brightness Press the MODE button to exit setup mode Press the MENU button twice to set the desired contrast The LED CONT starts flashing Press the button to reduce the contrast Press the button to increase the contrast Press the MODE button to exit setup mode Press the MENU button three times to set the desired color The LED COLOR starts flashing Press the button to reduce the tint Press the button to increase the tint Press the MODE button to exit setup mode Note You can reset the monitor to the factory settings for brightness contrast tint and volume To do this proceed as follows Press the MENU button once The LED BRI starts flashing Press the MODE button SPECIFICATIONS STSC108 CAMERA PICK UP DEVICE TV SYSTEM PICTURE ELEMENTS SENSING AREA IMAGE SIZE SYNCHRONIZATION HORIZONTAL RESOLUTION REQUIRED ILLUMINATION SIGNAL TO NOISE RATIO POWER SUPPLY POWER CONSUMPTION CURRENT CONSUMPTION LENS ANGLE OPERATION TEMPERATURE STORAGE TEMPERATURE WEIGHT DIMENSIONS W x H x D
Download Pdf Manuals
Related Search