Pro-Ject Debut Carbon Phono/USB - Luxusní
Contents
1. Pro Ject INSTRUCTIONS FOR USE Pro Ject Debut Carbon Phono USB St Ted sets ao i 14 E U 2 Audio Trade GmbH Pro Ject Debut Carbon Phono USB Ortofon OM10 Revision 2013 11 15 Pro Ject Debut Carbon Phono USB Controls features and connections 1 Motor brackets with Sorbothane pads 2 Stepped drive pulley 3 Drive belt 3a Hook 4 Hub 5 Platter with felt mat 6 Tonearm counterweight ba Downforce scale 7 Tonearm lift lever 8 18 Tonearm rest and removable transport lock 9 Tonearm tube 9a Tonearm base 10 Lid 11 Lid hinges 12 Hinge fasteners 13 Mains lead 14 Phono output sockets earth connection and USB out 15 Anti skating stub with anti skating weight adjustment scale 16 Anti skating weight 17 Anti skating weight support hoop 19 Power switch 20 Headshell with finger lift and fitted Ortofon OM 10 cartridge 21 Motor 22 Single adapter 23 3 5mm connector Connection cable not shown Dear music lover thank you for purchasing a Pro Ject Audio record player In order to achieve maximum performance and reliability with this record player you should study these instructions for use carefully V Warning of a hazard for the user the unit or possible misuse 5 Important notice Your turntable has been2. 15 Connection to the amplifier The record player has gold plated female RCA phono sockets 14 so you can substitute the interconnect cables supplied with higher quality cables such as the Pro Ject Connect it interconnect cables for connection to the amplifier if you wish Use a line input such as AUX CD Tuner Tape or Video on your amplifier Due to the built in phono pre amplifier a phono input sometimes labelled gram disc or RIAA is not suitable Take care to connect the left and right channels correctly The right channel is usually marked red the left channel black or white Check the manual supplied with your amplifier for relevant information The earthing wire of the tonearm lead should be connected to the earth terminal on your amplifier if provided For detailed product information regarding Pro Ject Audio interconnect cables please refer to the Pro Ject web site www project audio com nes The recommended load impedance for the factory fitted cartridges is 47kohms MM input The 3 5 mm connector supplied can be used to connect your Pro Ject Debut Carbon Phono USB to any line level auxiliary input Computer Midi System Mixer etc Connect the socket end to the phono plugs at the end of the audio trailing lead from your turntable and insert the 3 5 mm plug into the relevant socket on your audio component Connecting to a Computer Connect the USB output of the unit to a free USB socket on your computer and turn it on
3. delivered with a factory fitted and adjusted cartridge please ignore the cartridge set up instructions unless changing the cartridge at a later date During assembly and adjustment of the deck small parts could be lost if not carefully placed in a suitable receptacle Before starting assembly make yourself acquainted with the parts listed above and correspondingly numbered in the technical drawings above Separately packed items are marked with an asterisk Safety instructions AC outlet voltages vary from country to country Before connecting to the mains make sure that the voltage in your area meets the voltage requirements printed on a label underneath the unit The power cord plug and the power switch 19 are used to disconnect the unit from the mains Make sure that the plug and the switch are easily accessible at all times Hold the plug when unplugging the power cord Never handle the power cord while your hands are wet or damp V Avoid letting liquids enter the device Never place any item containing liquid such as a flower vase on or near the device Never spill any liquid on the device Never place any naked flame sources such as lighted candles on or near the device The product shall not be used in damp or wet locations next to a bathtub sink swimming pool or any other similar conditions Keep plastic bags away from children to prevent any risk of suffocation Audio Trade GmbH Pro Ject Debut Carbon Phono USB Ortofon OM10
4. make sure it is powered on The new hardware found assistant will automatically detect the unit and announces it as a Microphone USB audio codec There is no need to install a driver manually After installation one setting has to be done For example Windows 7 operating system gt Control Panel gt Sound gt Recording gt Microphone USB Audio CODEC gt Properties gt Advanced set to 2 channel 16 bit 48000 Hz DVD Quality Please note Connection should be made to an USB socket of your computer directly Connecting to USB hubs or switches can cause problems Recording Programme In case you do not have a recording programme installed on your computer you may download one free from the Internet Recording programmes may be found by searching Google or Yahoo In the menu of the recording programme source or input may have to be set to Microphone USB audio codec Please be aware that downloads from the Internet are made entirely at your own risk Under no S circumstances can we carry responsibility or provide support for third party software products sourced from the internet or for any damage or problems arising from the use thereof All downloads should be checked with an up to date anti virus programme License fees may be applicable Mains power connection Connect the mains lead to the mains y AC outlet voltages vary from country to country Before connecting to the mains Make sure that the voltage in your area m
5. must be done carefully Do not forget to remove the cartridge protection cap if fitted Once the arm is correctly balanced return it to the rest Hold the counterweight 6 without moving it and gently revolve the downforce scale ring 6a until the zero is in line with the anti skating stub 15 Check whether the arm still balances out Rotate the counterweight counter clockwise seen from the front to adjust the downforce according to the cartridge manufacturer s recommendations One mark on the scale represents 1 MN 0 1g 0 1 Pond of downforce 5 Please note Adjust the downforce prior to installing the anti skating weight The recommended downforce for the factory fitted Ortofon OM 10 cartridge is 15mN Anti skating force adjustment The anti skating force must be adjusted corresponding to the downforce as follows 3 0 Downforce Groove inthe stub 15 10 14mN 1 from bearing rings 15 19mN giw de d 20mN and bigger 38 A i 15 Slip the loop of the anti skating weight s thread over the second groove of the stub to set the correct anti skating force for the factory fitted cartridge Feed the thread through the loop of the wire support 17 Fitting the lid Fit the lid dust cover 10 carefully over the hinge prongs and adjust the screws 12 until the lid stays open where you want it to without being too stiff to open or close 4 Audio Trade GmbH Pro Ject Debut Carbon Phono USB Ortofon OM10 Revision 2013 11
6. RIAA equalisation curve accuracy 20Hz 20kHz max 0 5dB USB output digital serial data protocol USB 1 1 Operating systems Windows XP Windows VISTA Windows 7 Windows 8 Mac OS Technical specifications MM Cartridge Ortofon OM 10 Frequency range 20 22 000Hz Channel separation 22dB 1kHz Output voltage 4mV Recommended load impedance 47kohms amplifier connection MM input Compliance stylus type 25um mN elliptical Recommended tracking force 15mN Weight 5g Potential incorrect use and fault conditions Pro Ject turntables are manufactured to the highest standards and undergo strict quality controls before leaving the factory Faults that may possibly occur are not necessarily due to material or production faults but can sometimes be caused by incorrect use or unfortunate circumstances Therefore the following list of common fault symptoms is included The platter doesn t turn although the unit is switched on The unit is not connected to the mains power supply No mains at the socket Drive belt is not fitted or has slipped off No signal through one or other channel or both channels No signal contact from the cartridge to the internal tonearm wiring or from that to the arm lead or trom that to the phono box or between that and the amplifier This could be due to a faulty plug broken wire or solder joint or simply loose plug socket connection Wrong input selected at amplifier Amplifier not switched on Amplifier o
7. Revision 2013 11 15 3 Set up The deck is supplied partially disassembled and carefully packaged for safe transport Carefully remove all parts from the transport packaging Make sure the surface you wish to use the turntable on is level use a spirit level before placing the turntable on it Remove the transport lock 18 from the tonearm Store it in the original packaging so it is available for any future transportation Fit the drive belt 3 around the hub 4 and the smaller diameter part of the motor pulley 2 Avoid getting sweat or grease on the belt as these will deteriorate the performance and reduce the belt s lifespan Use absorbent kitchen paper to remove any oil or grease from the outer edge of the hub and the belt Fit the platter 5 and felt mat over the spindle of the hub 4 Cartridge downforce adjustment The counterweight 6 supplied is suitable for cartridges weighing between 4 5 6g weight no 80 An alternative counterweight for cartridges weighing between 6 5 8 5g weight no 08 is available as an accessory part Pushing carefully turn the counterweight 6 onto the rear end of the tonearm tube 9 so that the downforce scale 6a shows towards the front of the player Lower the armlift and position the cartridge in the space between arm rest and platter Carefully rotate the counterweight 6 until the armtube balances out The arm should return to the balanced position if it is moved up or down This adjustment
8. ck it Maintenance and cleaning Your record player requires little or no regular maintenance Remove dust with a slightly moistened antistatic cloth Never use a dry cloth because this will create static electricity which attract more dust Antistatic cleaning fluids are available at specialist stores but must be applied sparingly to avoid damage to rubber parts It is recommended to fit the needle cover before cleaning or maintenance is carried out to avoid damage If the player is not used over a long period of time the drive belt can be removed to prevent unequal stretching NW Always disconnect the record player from the mains power supply as a precaution before maintenance 6 Audio Trade GmbH Pro Ject Debut Carbon Phono USB Ortofon OM10 Revision 2013 11 15 Technical specifications Pro Ject Debut Carbon Esprit Pro Ject 8 6cc Nominal speeds 33 45 r p m Speed variance 0 8 Wow and flutter 0 1 Signal to noise 68dB Effective tonearm mass 69 Effective tonearm length 8 6 218 5mm Overhang 18 5mm Power consumption 7 5W 0W in Stand By Voltage suitable for your country s mains supply Dimensions W x H x D 415 x 118 x 320mm dust cover open 415 x 365 x 405mm Weight 6kg Technical specifications moving magnet phono pre amplifier A D converter typical for MM or high output MC cartridges Input capacitance input impedance 47kohms 100pF Gain 32dB Output voltage typically 200mV 1kHz at 5mV Noise floor 88dB
9. eets the voltage requirements printed on a label underneath the unit Useful tips The record player should be positioned on a low resonance surface such as wood or multiple layer ply board to avoid structural vibrations disturbing replay Switching on and off Pressing the power switch 19 alternately starts or stops the motor Audio Trade GmbH Pro Ject Debut Carbon Phono USB Ortofon OM10 Revision 2013 11 15 5 Changing replay speed To play records at 45 r p m first remove the platter 5 Using the accessory tool provided 3a hook the belt 3 over the larger diameter part of the motor pulley 2 Refit the platter To revert to 33 r p m repeat the proceedings using the smaller step on the pulley Fitting and connecting the cartridge All cartridges with half inch mounting holes can be fitted Leaving the needle s protection cover on fit the cartridge to the headshell using the screws supplied with the cartridge by passing one screw through each slot in the headshell 20 Do not tighten the nuts yet Connect the tonearm wires to the cartridge pins as follows white left channel positive L red right channel pos R green right channel return R blue left channel return L The full sound quality of the record player can only be achieved if the cartridge is correctly adjusted Particular tools like the Pro Ject alignment tool are required to accomplish this job properly If you are not well acquainted with
10. r speakers defective or muted No connection to the loudspeakers Distorted or inconsistent sound from one or both channels Record player is connected to wrong input of amplifier or MM MC switch incorrectly set Needle or cantilever damaged Wrong r p m drive belt overstretched or dirty platter bearing without oil dirty or damaged Audio Trade GmbH Pro Ject Debut Carbon Phono USB Ortofon OM10 Revision 2013 11 15 7 Service Should you encounter a problem which you are not able to alleviate or identify despite the above information please contact your dealer for further advice Only when the problem cannot be resolved there should the unit be sent to the responsible distributor in your country Guarantee repairs will only be effected if the unit is returned correctly packaged For this reason we recommend keeping the original packaging Never return a record player without making sure that is it safely disassembled and correctly packaged in the original packaging according to the diagrams on the last page of this user guide Please remove these parts and pack them separately lid 10 counterweight 6 anti skating weight 16 platter 5 and belt 3 Fit the cartridge protection cap Insert the transport lock for the tonearm 18 prior to carefully packaging the record player Warranty The manufacturer accepts no responsibility for damage caused by not adhering to these instructions 5 for use and or by transportation withou
11. t the original packaging Modification or change to any part of the product by unauthorized persons release the manufacturer from any liability over and above the lawful rights of the customer Copyright trademarks PRO JECT is a Registered Trademark of H Lichtenegger The information was correct at the time of going to m press The manufacturer reserves the right to make This guide was produced by Audio Trade GmbH changes to the technical specification without prior Copyright 2012 All rights reserved notice as deemed necessary to uphold the ongoing process of technical development Windows XP Windows Vista Windows 7 Windows 8 are trademarks of the Microsoft group of companies Mac and Mac OS are trademarks of Apple Inc registered in the U S and other countries 8 Audio Trade GmbH Pro Ject Debut Carbon Phono USB Ortofon OM10 Revision 2013 11 15 Tomearm transport look Tonearm counterweight Audio Trade GmbH Pro Ject Debut Carbon Phono USB Ortofon OM10 Revision 2013 11 15 9
12. the adjustment of cartridges you are advised to call upon the willing help of your Pro Ject dealer to accomplish this task for you Please note Adjusting a cartridge and tonearm calls for the greatest care in order to avoid damaging the cartridge or tonearm bearings Leave this work to your dealer if you are in any way unsure of the necessary steps and precautions to be taken Adjusting the azimuth The cartridge needle must be vertical in the record groove in order to trace the groove wall modulations correctly A small screw at the bearing end of the arm allows incorrect azimuth to be MEES Screw corrected if your needle is not mounted exactly perpendicular to the cartridge body n e which is often the case Slacken off the screw just enough to be able to revolve the arm tube without applying force Please note do not remove the screw completely With the aid of a good magnifying glass adjust the needle until it is vertical in the groove i e perpendicular to the record s surface Ideally this should correspond to the top surface of the cartridge body being parallel to the record surface When you are satisfied that the needle is vertical retighten the screw carefully Please note Under no circumstances should the arm tube be adjusted with the needle still in the record groove Irreparable damage may be caused to the cantilever suspension The arm must be litted to make each adjustment and lowered afterwards to che
Download Pdf Manuals
Related Search