Automatic Washing Machine User manual This
Contents
1. Normal Wash How to use It is recommended that washing powder liquid is dissolved with water and then directly emptied into the washing Bleach whitener machine not applicable for Fuzzy Logic and Delay program 1 Add some water select the 1 water level 2 Add washing powder liquid Run for about 30s to fully dissolve the detergent Then push the Start Pause button to pause the wash cycle 3 Load laundry Select suitable water level Push the Start Pause button again to recommence washing cycle Always refer to the bleach whitener instructions prior to usage Fill water to desired level Dilute the bleach whitener in a container Pour it slowly into the washing tub Avoid using whitener on laundry with colour or patterns as they are prone lose colour The bleach whitener should NOT be directly applied to laundry directly f you select Quick program it is recommended to use liquid detergent instead of washing powder to ensure the most effective wash results Old or poor quality washing powder may causing caking in tub or detergent dispenser Clean the detergent box periodically to ensure washing power is evenly distributed and remove any detergent buildup Note For best wash performance use low suds High Efficiency detergent and dissolve the detergent in lt 1L warm water prior to mixing with laundry Close the lid During a washing program the top lid will be activated If you want to open th2. lock is activatde all of the buttons are locked and can not make selection e Release the child lock function Press the Spin button and Delay button at the same time for more than 2 seconds After three beep sound the child lock function is released Remaining time display Displays during Fuzzy Logic detection cycle until level is determined Displays total remaining during current in progress wash cycle Displays remaining time when the Delay program is used hours e Displays error codes see page 15 Operation amp Wash Cycles Press the Temp Wash Rinse button to select your wash temperature During wool cycle the hot cold water temperature cannot be chosen Soak button For the Memory Synthetic Heavy Normal programs press the Soak botton select the desired soak time 5 10 20 30 minutes The button is unavilable in the Quick and Tub dry cycles For the Wool programs press the Soak botton choose or cancel soak process but can t change the soak time C D E Wash Rinse Spin button You may change the Wash Rinse and Spin times when Memory Heavy Normal and synthetic cycles are selected When the Wool cycle has been selected you cannot change the Wash Rinse and Spin times You can not change the Wash Rinse and Spin times when Tub dry and Quick cycles are selected F Delay button The display shows the time re
3. that are soiled or items that are heavy big Delicate Delicate items that are machine washable Lightly soiled or small laundry loads less than 1 5kg This cycle setting remembers the last soak wash rinse and spin settings Water level will not be remembered as it is determined by fuzzy logic function Synthetic Ideal for synthetic fabrics Machine washable woollen items Dries the inner and outer tub to avoid the growth of mildew START PAUSE button After the power is switched on press the Start Pause button to start the machine During operation push the Start Pause button to pause the machine Push the Start Pause button again to restart the machine J POWER button To turn on off the power press the power button f the start pause button is not pushed within 5 minutes the washing machine will automatically switch off the power 10 Operation amp Wash Cycles Button Operation and Descriptions POWER 1 Press the button to switch power on off 2 Press the button to select automatic program When the power is switched on Normal cycle is automatically set To select a different automatic cycle press the Cycle button till the corresponding indicator is on Refer to the section on the Cycle button above E g choose Quick cycle for a small load of lightly soiled laundry When the Synthetic Memory cycles are selected the Fuzzy Logic program is run The washing cycle i
4. tight connection Check the inlet hose connections 1 Swing the hose gently to confirm that the hose is securely fastened 2 After installation open the tap to check for leaks 3 Do not bend the hose unduly 4 Periodically check the hose connections are firm at both ends This is to ensure the connections remain watertight over time Removing the water inlet hoses 1 Turn off the water taps 2 Loosen each connection at faucet and washer 3 Carefully remove each hose separately as they may contain residual water Before washing Preparation Ensure the water inlet hoses are correctly installed and faucets are turned on Insert the power plug into the electrical socket Ensure the drain hose is mounted at the correct height Select a suitable location for the washer on a hard even Surface away from direct sunlight or heat sources e g Radiators heaters 459 cooking appliances etc LIC a 5 Any floor unevenness may J fe pon vam result in unstable working or 3 tk y abnormal noise Please ensure the machine Is level Check the following before washing Check if the Clear the pockets Tie any long The weight of the When the machine is laundry has and take out Straps or laundry shall not running buttons may any special loose items such strings fasten exceed the rated cause noise To washing as coins sand buttons and capacity of your reduce the noise turn instructions hairpins etc close
5. zippers machine Loosen clothes inside out or the laundry before place them in a laundry placing it evenly bag in the tub T so e a Check if the laundry is suitable for machine washing b Divide the laundry into colour fast and non colour fast items c Separate items that do not absorb water easily and wash by hand d For heavily soiled items please first remove loose dirt then apply detergent directly as per instructions on pack to the stain before washing e For those items that may attract lint or are furry or fluffy please turn inside out before washing f Do not put laundry soiled with chemicals or solvents into the washing machine Loading your laundry The rated washing capacity refers to the largest dry weight of a load that can be washed The thickness size and type of clothes will influence the actual capacity Do not select more than Water Level 4 for clothes less than 1 0kg to avoid splashing of water It is recommended that low suds High efficiency detergent is used Detergent usage guide Adding washing power It is suggested to dissolve detergent before adding to the tub see as below 1 Prepare warm water lt 35 C in a container 2 Add washing powder stirring to dissolve it completely Adding washing powder Fuzzy Logic Programs Add washing powder liquid into the detergent box directly for Fuzzy logic programs and Delay program Adding washing powder
6. Automatic Washing Machine User manual This manual is for HWMP75 918 e Please read this manual carefully before using e Retain for future reference mlo llei CONTENTS Product Overview oo cccsccccccccescescccscccceccccccccccsccecess Safely Precallions lt srsceswesenesevennpeeeduardsanesieveesaices Installation and Adjustment ssseseeeesseeereesesererseeeeee Installation of drainage hose Installation of water inlet hoses Before washing sssssseeesesseessssesessssosessesosessoseees Loading your laundry ssseereeseereeseeeeeseeceeseeceeeeees Detergent usage guide ssesessececsececeececcocecocceceeoe Operation amp Wash CyClES sesessessseseecoseceeoocoecoee Maintenance Troubleshooling 024 sonncsarsecwsereienedsincsnesaianatat a Packing list Specifications Product Overview Cold water inlet valve Hot water inlet valve Detergent box Bleach Inlet Balance Power cord ring Inner tub Hook Lint filter Pulsater Lid Lock Back cover Control panel Drain connector Cabinet Base frame Adjustable leg Fixed leg 2pieces 2 pieces Description of symbols Contents marked with this symbol are related to the Warning sign safe use of the product and the personal safety of the user Please operate in accordance to the contents of this manual to avoid harm to the user or damage to the Q machine itself Contents marked with this symbol indica
7. after cleaning t must be cleaned after each use Lint filter 1 Slide upwards to remove 2 Gently push it down to install ensuring it is in place before Ay w Dismantle Install Install The filter screen of the water inlet valve If the cabinet is dirty wipe it with a damp cloth may become to be blocked by foreign Do not wash directly with water materials and influence the water inlet Wipe with a neutral detergent please check Please clean it with brush every two directions on detergent bottle first months Do not wipe machine with thinners petrol alcohol or other harsh solvents 1 After washing cycle has finshed turn off the water faucet If needed you can remove the water inlet hose 2 Do not store water in the washing machine for a long period without completing a wash cycle Drain the water completely after each wash 3 Hang up the power cord and drain hose 4 Wipe up any drops of water on the surface of the machine and inside the tub Leave the lid open for about 1 hour after each wash to evaporate any residual water 14 Trouble shooting lf there is a fault or the machine does not operate correctly remove the power plug before checking the machine Using diagnostic list below please check the machine requires repair If a repair is required please contact our Customer Care Team do not try to fix it yourself The machine does not Is the drain hose blocked Remove the blockag
8. bute the laundry unevenly in the machine There are abnormal Is the machine level Redistribute the load sounds inside the Has the laundry been place evenly Close the top lid machine unevenly in the machine Level the machine Are there any foreign Remove the foreign object objects inside the bowl is the water inlet hose Fasten the inlet hose loose The water tap leaks 15 Common occurrences Situation Cause e The spinning is intermittent e Redistribute the load evenly when it starts Close the top lid e The wash procedure pauses e The cloth sensor is detecting it will add water after about 48 seconds e Select spin program e A period of time is needed before but it does not work the spin program starts e There maybe water in the e It is the water remaining after the drain hose in when first used performance inspection by the factory 16 Packing list Quantity Storage position Automatic washing machine Bottom plate Between the upper cushion of the washing machine package and the upper seal of the package carton User manual Inside the document bag Warranty card Inside the document bag Tapping screw Inside the accessory bag Components of the Inside the accessory bag water inlet hose Connect to the washing machine Connect to the tap Inside the accessory bag Inside the accessory bag Inside the accessory bag 17 Specifications Fu
9. chine become damaged or faulty please contact a technician to have it repaired DO NOT attempt repairs yourself as this may cause personal harm or void warranty Please remove items such as coins buttons sand and other solid materials from clothing before washing EF cs Check that water faucets are open after connection to machine prior to operation and that pipes are connected correctly Please use low suds High Efficiency washing powder Installation and Adjustment Please install and adjust the machine according to the directions contained in this manual It is very important to follow these directions for the safe operation of the machine and to ensure your machine operates correctly Install the bottom plate The purpose of the bottom plate is to suppress noise from the washing machine during operation Steps 1 Lay the washer on its back on a non abrasive surface 2 Place the plate on to the bottom of the machine 3 Use a screwdriver to tighten the screw in accessory bag securing the panel to bottom of the washer I 4 Once the screw is tight and the panel is secure return es the washer to its standing position Balance washing machine Do not install this machine on an incline greater than 2 Installing machine on an angle or on rough ground will result in unstable running or stoppage of the machine Please adjust it by the following method 1 Confirm it is level 2 Lift up the side of th
10. e Open and close the top lid once drain or drains slowly The display shows E1 The machine stops running The top lid is not closed Close the top lid The display shows E2 The machine does not Has the laundry been Redistribute the load spin The display shows place unevenly in the evenly close the top lid E3 machine Level the machine The Is the machine level machine will start 10 seconds after being leveled correctly The display will show E4 Is the water tap opened or Open the water tap Push within 30 minutes has the water supply been the Start Pause button once interupted Clean the water inlet valve Is the water inlet valve then push the Start Pause blocked button once Is the water pressure too Push the Start Pause low button once The display shows E6 The water level sensor Please contact the after sales has failed service department The display shows E8 Lid lock fails to lock Switch off the power switch on again Will not Is there a power failure Wait for the power supply wash Is the power plug inserted to be restored The machine tightly Insert the power plug does not Has the water level tightly work reached preset position Wait for water to fill to the preset level Will not Is the power plug inserted Insert the power plug spin tightly tightly Is the top lid closed Close the top lid Is the laundry distributed Redistri
11. e leg slightly and twist the adjustable leg Note The distance between the washing machine and wall at least 20 mm Installation of drainage hose Install drainage hose First connect the drainage hose to the connection point on the lower f right side of the cabinet and fasten with drain hose clamp provided Drain hose neck guide Connect drain hose guide on to the outside of drainage hose To guide S the drain hose over the tub or standpipe the hose guide MUST be fitted to the drain hose Drain hose Drain hose joint clamp Placement of Drainage Hose The height of the standpipe or tub should be between 850 1200 mm To avoid syphoning the drain hose should not extend more than 20 mm from the end of the guide 0 8m lt h lt 1 2m Ensure drainage hose is held in place to avoid leaks or spills Installation of water inlet hoses NOTE Use the new inlet hoses supplied do not reuse old hoses 1 Insert a new flat washer into each end of the inlet hose Joe Sas 2 Connect the water inlet hose to the water faucet You may have SY to use pliers to tighten the coupling Do not over tighten as this may cause damage to the valve or hose fittings 3 Connect the other ends to their respective cold and hot water inlet valves located on the top of the washer Nut of the water mM hose Water absorption cushion to Joiner of the water inlet valve 4 Fasten each hose on the washing machine and ensure a
12. e top lid please press key START PAUSE button and the washing program will pause The top lid will be unlocked and you can access your laundry Operation amp Wash Cycles START POWER Memory Normal PAUSE Synthetic Heavy O HotiCold a Warm Cold RC EPOE Wool Delicate OD N AO O Rapid C 1 Rinse Express Cold Cold amp Tub dry Quick J H WO ON Indicator displa Off L On Indicates the program is about to run and indicates the selected cycle and options Q Flashing Indicates the program is running and indicates the selected cycle and options Lid lock function During the washing program the lid lock will continue to function even with the power off and power plug removed from the wall socket When the washing program is over please wait for the light of lid lock to go out before removing the power plug from the wall socket e f you want to cancel from lid lock function press START PAUSE button during the washing program NOTE In order to protect the washing machine please don t try to open the top lid while the lid lock light is on Child lock function e The function is intended for children safety and preventing the washing program from accidental changes by children e Hold the Spin button and Delay button then press the Power botton the child lock light on set desired washing procedures After setting press the Start Pause button the child
13. ectrical portable outlet device the cord extension set or electrical portable outlet device must be positioned so that it is not subject to splashing or ingress of moisture Do not connect to hot water higher than 50 C temperature Do not wash water proof clothing as this may affect load balance during spin cycle s If you are using an extension cord or a portable electrical outlet device not recommended ensure that it is positioned so that it does not come into contact with water or moisture Safety Precautions Do not attempt to move washing or place hands inside washing machine while in operation Please ensure children are supervised around machine to avoid harm Do not leave hot or heavy items on lid or control panel as this may cause damage to the washer or make the washer unsafe to operate This clothes washer is not intended for use by children and persons with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Do not take apart repair or alter the machine by yourself Do not wash laundry with chemicals or other volatile materials Such as petrol solvents or thinners as this may cause damage 2s to the machine Keep washer away from heat sources such as heaters stoves or direct sunlight If power cord or other parts of this ma
14. lly Automatic Washing Machine 220 240V 50Hz Net weight About 46 kg Gross weight About 54 kg Dimensions mm L610 W620 H995 Water level Water 1 24L 2 34L 3 44L 4 52L Quantity approx 5 60L 6 68L 7 76L 8 85L Water inlet pressure 0 03MPa 1 0MPa when water temperature is 50 C the water inlet pressure of hot water shall not exceed 0 4MPa Note Default settings when you choose this program after power on _ Water Delicate Rapid 2 Rinses 5 Min 6 Warm Cold 46Min Quick Express 1 Rinse 9 Min 2 Warm Cold 10 Min Memory This cycle setting remembers the last soak wash rinse and spin settings Synthetic Medium 1 Rinse 5 Min 6 Warm Cold 18 Part No 0030810251
15. maining in minutes before the cycle will finish Push the Delay button and the display will show the remaining time for the cycle to finish in hours The indicator flashes to indicate that the delay function is operating Delay start can be set for 2 24hr operation NOTE The delay time is until the selected wash program finishes you will need to deduct wash time from this delay time to calculate when the wash will start G Water Level button e During the Memory and Synthetic programs the washing machine will detect the size of the laundry and automatically select the water level between levels 2 4 6 or 8 To change the water level press the Start Pause button and make your selection by pressing the Water Level button until desired level is shown 1 8 f there is water inside the tub and the machine cannot detect the laundry load it will display water level 6 f Quick program is selected it will display water level 2 you can then manually adjust to the desired water level f Tub Dry program is selected the water level cannot be manually overridden e During operation of the wash or rinse program you can adjust the water level by pressing the Water Level button The water level may vary due to the different moisture level of the laundry items Operation amp Wash Cycles Cycle button Recommended for Normal Recommended for mixed fabrics and general clothing items ltems
16. ram is automatically off and wash cycles will start as soon as Start Pause button is pushed Confirm the operation of Delay program To set a delay time first select the Cycle and options required and push the Delay button The cycle indicator lights will go off and the Delay Hours indicator light will be on During the delay program press the Delay button to display the time remaining The delay time indicator shows the time remaining till the wash ends To cancel the delay program switch the power off and back on then make a new selection Delay start 2 24hr option Delay time is to the end of washing washing cycle The wash will finish in about 18 hours Start Pause Press the D button to start the cycle 12 Operation amp Wash Cycles Cycle completed When the machine has completed the selected current wash cycle an audible alarm will sound and the machine will switch off automatically Note e The energy test program was performed using the Normal cycle default setting of Soak 20 Min Wash Long Rinse 1 Rinse Spin 7 Min Water level 8 e Please use low suds high efficiency detergent 13 Maintenance e Remove the power plug before carrying out any cleaning or maintenance e Clean the lint filter s and detergent box after each wash Remove and clean the detergent The lint filter must be used during washing box replace
17. s automatically set while the water level and wash time can be selected according to the texture and size of the load 3 Press the Goat vas ins Eri buttons to customise the pre set options Even there is no water in the tub a certain period is required before spinning Separate colour fast clothes before loading washing machine During Rinse cycle only SPIN times can be set all other wash functions are locked During Wool and Tub Dry cycles these settings cannot be changed and buttons will not function as machine will only follow pre programmed settings 4 Press the vateh button to change the water level For the Synthetic and Memory cycles the machine will run a Fuzzy Logic program that automatically detects the type of laundry in the tub After detection it will set the water level automatically he water level can only be changed once the machine has started by pushing the Start Pause button then push the Water Level button to reset the water level Press the Start Pause button to resume the wash cycle D Press the button to select the the wash and rinse temperature Set the wash and rinse temperatures in accordance to the requirements of each load The wash and rinse temperatures will be the same i e if Warm Cold is selected both wash and rinse cycles will be warm cold 11 Operation amp Wash Cycles 6 Press the button to select the delay wash program The delay time prog
18. te operations or actions that should not be undertaken by the user Performing of such actions may result in injury to the S user or damage to machine itself and void warranty Forbidden sign SAFETY WARNING Please check power socket condition to ensure it has been earthed correctly prior to installation to ensure your safety Safety Precautions A separate earthed power socket is required for the power supply Hold the plug NOT the electric cable when unplugging the washing machine Do not insert or remove the power plug with wet hands After installation of the washing machine the power plug should be accessible If power cord or other parts of this machine become damaged or faulty please contact a technician to have it repaired DO NOT attempt repairs yourself as this may cause personal harm or a void warranty Do not install this appliance in a damp or wet environment Do not leave wet laundry on the control panel or spray water directly on to this appliance as this may cause the washer to malfunction or cause an electrical Do not block the ventilation holes with carpet Ensure carpet does not obstruct the opening under the base of the cabinet a Soft object 9S Ensure the plug is removed and the taps turned off in the following cases power failure cleaning moving installation and when not in use CAUTION If this appliance is supplied from a cord extension set or el
Download Pdf Manuals
Related Search