CAMBRIDGE USERS MANUAL LCD Monitor User
Contents
1. Phase e Open the Phase function and e Press the UP or DOWN buttons to adjust phase analog to digital for the screen display Clock e Open the Clock function and e Press the UP or DOWN buttons to adjust clock horizontal stretch for the Display 20 150 7000 002 OPTIONAL TOUCH SCREEN Optional Touch Screen Installation If you are installing a new operating system O S do not install the Touch Screen Controller Driver CD until you have installed the O S and verified the computer s CAUTION monitor display is working properly The Touch Screen Controller Driver uses the computer s O S display driver software settings to accurately configure the Touch Screen Controller Driver files Previous Versions of Touch Screen Controller Drivers Previous versions of ANY Touch Screen Controller Driver must be removed before installing the latest version of the TSHARC Touch Screen Controller Driver CAUTION Uninstall TSHARC Utility Uninstall a Previous Version of TSHARC The uninstall utility TSUN10 exe is included on the TSHARC Touch Screen Con troller Installation CD in the shipping box with the product accessories This utility uninstalls TSHARC drivers only From the Product CD To uninstall install the CD gt go to My Computer desktop gt Left double mouse click gt Locate the drive with the Installation CD gt Left mouse click to open gt Left double mouse click on the Uninstall Driver2. The display touch is now active 150 7000 002 Touch screen diver initalishon congu s complete Press Fresh to install the touch screen diver aon is now The touch screen tay applicshon automsbc liy recalculstes comdnates when the screens ae reszed or rotated This process suns in the background and is configurable by Select Control ang the Hampshwe System tray icon Configure EZ omapcady stat Touch Scseen Tray Applic ation 27 APPENDIX A Mechanical Drawings Mount diagrams and its dimensions may assist you in installation of the Monitor You may find them on our website at http www aydindisplays com navigate to Marine Bridge COTS Displays Mount diagrams of the optional Flush Mount Bezel and its dimensions may assist you in installation of the Monitor You may find them on our website at http www aydindisplays com navigate to Marine Bridge COTS Displays APPENDIX B Display Symptom Vo ight behind button LEDs Possible Problem Solution No power loose power connection Confirm the Monitor is properly connected to a DC or AC power source Verify the power source is live or try another battery or AC power outlet Verify the Monitor is powered on Reverse Polarity Check polarity of the power connection Symptom Light behind button LEDs no display or No Signal error message and or no image on the display Possible Problem Solution Power on no video signal Verify the video cable is p
3. USER TIP Power on the Monitor e The Windows Operating System should automatically apply the best generic driver for this connection and e Follow the instructions under section Computer Display Properties for optimum display quality 150 7000 002 15 OPERATOR CONTROLS On the right hand side of the Monitor bezel are seven Operator Control buttons Power On Off 1 0 Power Button Button Note Monitor defaults to an AUTO OFF state when i power is applied Brightness Control Toggle e The Power On Off button is marked with large sun small sun the I O Input Output symbol he e Momentarily pressing this button shall a turn ON or turn OFF the unit and e Select Button e Blue LEDs glow behind the buttons when Jl the unit is powered on Up Button Optional Feature Monitor defaults to an m AUTO ON state when power is applied This ITA Down Arrow feature must be ordered when the Monitor is ordered It is not an add on after the unit is Source Select Button built Brightness Toggle This toggle controls the brightness of the LCD Panel Display e The large sun toggle side when repeatedly pressed or held down shall cause the Display s backlight brightness to increase e The small sun toggle side when repeatedly pressed or held down can be stepped down in increments to the lowest setting which is just above total black and suit able in very subdued light as in night time operations and e The Monitor shall revert
4. AYDINDISPLAYS a 9 sSparton company CAMBRIDGE USERS MANUAL ALL WEATHER 8 4 15 0 IP67 SEALED SERIES MILITARY GRADE PANEL MOUNT ARM MOUNT A 10 4 LCD Monitor User Guide Part No 150 7000 002 Table of Contents IntrOdBW ctlOFL ii ia 7 System Set Up oo c ccc ccc cece cece cece eee ueeeeeeeueeeees o ic PP ensixndenes Display Connections wisicisdieeerceerivercrcenaeresnacs Computer Hook up osiconiconracca rta in Operator COntrols ccc cece eee eee eee eee On Screen Display OSD 0 0055 Optional Touch ScreenN ccccccccccccccccccccncooo Appendix A Mechanical Drawings Appendix B Troubleshooting D Appendix C Technical Environmental Specifications 150 7000 002 oo fF O 11 13 16 17 21 28 28 31 The Aydin MIL Spec Monitor is a ruggedized marine grade LCD Display for use with a conventional RGB computer input It is designed to operate under the most extreme environments found in high performance vessels such as public safety government and military marine craft as well as submarine vessels The ruggedized displays are capable of operating in environments that include extended temperatures extreme shock and vibration direct exposure to salt water and other environmental conditions Housed in a milled billet aluminum case the slim profile model is light weight and watertight with fully sealed military grade
5. To retal the Haespihre TSHARC controler diver now chek Screen Controller Drivers Installation CD Accept HEULA New oi pess Erlet 5 Left mouse click to open ad eps 7 Configure ues 6 Left mouse double click to open the Resistive Install paid abel aran porel To Uu C h D r ve r fi e ion hs prom bad portion i may saan severa civil caminal penshes and val be prosecuted to the 7 Left mouse double click to open the file for See ree 2000 XP 98 ME O S and LEAR 8 Left mouse double click to run set up exe 22 150 7000 002 If you need to cancel this driver installation at any time select the Cancel button on the driver installation dialog screen CAUTION pc nanan 1 At the Welcome screen select Next to go to the Software License Agreement EULA 2 After reading the EULA if in agreement check the box l accept all of the terms 3 Select Next Please read Ihe following license agreemanl HAMPSHIRE Fiezs the PAGE DOWN key ta see the rest cl the agieement Hamashiee End User License Agreement HEULA PLEASE READ THE LICENSE AGREEMENT ln COMPANY m vis VUES RA FOR HAMPSHIRE J ODUCT SOFTWAR IMPORTANT READ CAREFULLY This Hampshire End User License Agreement HEULA is a legal Welcome agreement belween you einer an individual or a singe erfly and Hampshire Merit Inc for Ihe Hampzhiee Accept HEULA sollwae product ideriilied above which includes computer software and may ur
6. 2 Use the slide bar to set the Touch Screen event area to a size slightly larger than the activator larger for a finger tip smaller for a stylus the box displays the activator size Right Click Delay The timed hold right click mouse event allows the user to initiate a right click by holding down a touch point for a specific period of time de Won Ke pa 3 Use the slide bar to set the Right Click Delay value to the time necessary to produce a right click event Double Click Area This step sets the area that shall allow for a double click event Limit this to areas that can be accurately touched several times 4 Use the slide bar to set the double click area the box displays the activator size Double Click Speed 5 Use the slide bar to set sufficient time to perform a double touch in the specified area 6 Select the Apply button to enter the selection and 7 Select the OK button to apply all Click Settings Touch Settings 1 Normal Emulates a standard mouse allowing a single click double click drawing dragging and right click option if enabled 2 Touch Down Allows for a click event to take place at touch down No draw or drag is available 3 Touch Up Touch only Double click is disabled If right click was earlier enabled it shall be disabled Touch Sound 1 Check the Enable Touch Sound to enable a tonal beep when the screen is touched 2 Select the Apply button to
7. on the four corners of the unit s rear panel Take care not to strip the screw holes or over tighten CAUTION as the enclosure is aluminum Figure 5 10 150 7000 002 DISPLAY CONNECTIONS Connectors A Use care when inserting or removing connector Do not force their mating CAUTION There are two 2 MIL DTL connectors on this model Power Input and Video Input Figure 6 7 Connectors are located on bottom of Display housing From left to right Power Input a 3 Pin Connector and Video Input a 13 Pin Connector 1 Power Input 2 Video Input Figure 6 Figure 7 Power Input The Power Amphenol Connector is a MIL POWER CABLE DTL 26482 Series Connector 3 PIN PLUG MIL C 26482 SERIES e End User supplied or Optional Power Cable e 3 Pin Connector pin out is listed in Table 1 PIN TON e Line up with Connector 1 in Figure 7 OA 28 VOLT DC e Add a twist to lock B 28 VOLT RTN CHASSIS GND 71 533721 33P MATE PTOGE833SSR Table 1 Consumption WARNING The 8 4 10 4 and 12 1 are listed at 20 watts The 15 is listed at 35 watts 150 7000 002 11 Video Input The Video Amphenol Connector is a MIL DTL 38999 Series Connector See Table 2 Add a twist to lock 12 150 7000 002 End User supplies Video Cable 13 Pin Connector pin out is listed in Table 2 Line up with Connector 2 in Figure 6 VIDEO CABLE 13 PIN PLUG MIL DTL 38999 SERIES SIGNAL Red Video Signal Red Video
8. ARA l 6 Following installation select Finish and Ces 7 Reboot the computer when prompted TSHARC Calibration Program Upon reboot the Touch Screen is functional but not calibrated Calibration must be configured for the Touch Screen to work properly The TSHARC Control Panel initiates the calibration process e Go to Start gt Programs gt Hampshire TSHARC Control Panel The Control Panel has five tabs Each tab provides links to tools that can modify the TSHARC Drivers to meet specific needs Touch Screen Display Selection Calibration Click Settings Touch Settings Capacitive Settings TSHARC Control Panel Screen Selection Note If this is not a Multi monitor installation skip to section Calibration Configuring a Multi monitor Installation No te Microsoft does not support a Multi monitor Hampshire TSHARC Control Panel Rev 6200 ae xj installation in Win98 SE Sessa Seinen Caisan Cick Sening Touch Settings Capacitive P Selection Infomation HAMPSHIRE 0259 1 Select the monitor lo calbrate 1 The controller installation program opens to the Screen Selection tab Note the graphic representation of the Monitors installed on the COMPANY system 2 Using the keypad or the mouse select the Monitor to calibrate 3 Switch to the Calibration tab Go to the next section Calibration 4 When complete return to the Screen Selection tab select the next Monitor Repeat the process until all Monitors ar
9. Ground or UPS Ground Shipments that are not FOB consignee or third party will incur a 20 handling charge and be added to the invoice Delivery is not guaranteed All risk of loss is assumed by the purchaser upon delivery by Aydin to the carrier Special terms may apply for international shipments Unless otherwise specified by the purchaser and accepted by Aydin at the time of purchase Aydin reserves the right to partial ship any order Cancellations Once an order is placed by the purchaser and accepted by Aydin cancellation charges will apply to any and all unshipped items Partial credit may be extended if products are returned unused in original packaging within 30 days of shipment No credit will be issued on any returns or cancellations after 30 days from date of shipment Returns Once a product has been shipped no returns will be accepted unless an RMA number has been issued by Aydin prior to it s return The RMA number must be prominently displayed on the outside of the returned packing materials Aydin cannot be responsible for damage from shipping All authorized returns must be shipped prepaid directly back to Aydin in the original packaging Returnee is responsible for all shipping and handling costs to and from the closest Aydin authorized repair location For authorized in warranty service only Aydin will pay for the return of the unit via normal domestic ground service Expedited return service or shipment outsid
10. available from the manufacturer s web site Touch Screen Installation TSHARC Touch Screen Controller Driver A TSHARC Touch Screen Controller Installation CD is included in the shipping box with the product accessories The driver is compatible with these O S Windows 98 SE Second Edition ME 2000 and XP Before loading Touch Screen Controller drivers verify the COM ports are enabled caution especially if using a laptop computer Installation 1 Attach the RGB Touch Screen Cable to the connector 2 2 Attach the Touch Screen Cable RS 232 connector to a computer serial port or 3 Attach the Touch Screen Cable USB connector to a computer USB port Note For Multi monitor applications all Touch Screens must be connected to the computer before installing the TSHARC driver e f installing RS 232 connectors the driver has to be installed for each Touch Screen or CAUTION e f installing USB connectors the driver is installed one time for multiple Touch Screens e f the Touch Screen connector is USB Window shall load a temporary USB driver Wait for the driver to load 1 Boot up the computer Welcome 2 Insert the TSHARC Controller Driver CD 3 On the desktop left double mouse click on HAMPSHIRE Welcome to the TSHARC touch screen controle diees Setup the My Computer icon c o ERSTER CEOUNME icros i amp Each Setup da as ins ora for 4 Locate the drive with the TSHARC Touch ace o i at S
11. between Touch Screen types user may want to calibrate the edges of the Touch Screen more precisely Default is 20 1 Press the Center Graphic to start calibration 2 Targets are used to calibrate the Touch Screen Follow the on screen instructions Touch the target center hold until it shrinks then release the target and 3 Repeat the process for all targets Note the calibration screen shall time out and return to the Calibration tab if the first point is not touched within 10 seconds Calibration Verification Test 1 Touch the screen in several places to verify the calibration target is displayed under the finger and 2 Select the Accept button to apply and record the calibration data al store IARC Control Panel Ney Ges Sereen Selection Caltuation Cick Setings Touch Setra Capacitive Note If the calibration target is not displayed under the finger select the Cancel button repeat Custom Calibration Settings then Calibration Process 150 7000 002 25 2 Using a finger or stylus draw or write and 3 Observe if the screen displays the drawing accu rately If it does not repeat the Custom Calibration Settings and Calibration Process instructions 4 Select the Quit button to exit the test Click Settings Right Click 1 If desirable for Touch Screen application check the Enable Right Click box to set the right click option Right Click Area
12. connecting through a USB interface select the USB radio button Select Next 7 Following installation select Finish and 8 Reboot the computer when prompted O Select Controller Autodetect RS 232 Controller Set up 1 Select the Autodetect button 2 The AutoDetect Serial dialog box lists the Instructions 1 Select Ihe controller lypa 2 Select controller interface Lupa Y Controller Type detected RS 232 controller information Select 120 10 B Controls OK Welcome Conlrcles anircel er Imedace Accept HEULA s 3 Installing Touch Screen Driver text box pops EE F soil Iza up indicating the progress of the installation Configure r USB Following installation select Finish and eoe Reboot the computer when prompted o Back Het Cancel 150 7000 002 23 Serial Configuration 1 Select the commuricelian pert that pour touch screen controller is connected ta 2 Select the baud sale Ihs your bouch screen controller is radio button 2 Select Next HAMPSHIRE COMPANY COM Pot Note Do not select Autodetect S feu ren E 3 Follow the instructions entering the COM port a AA oe selection Select Controller APTA ae ip Configure Tod hae a 4 The Touch Screen Controller baud rate default TE O ia is 9600 10412 BIT C aeoo C 19200 a el Senal Note Capacitive Controller option is not available a Glan eave Cosa Colo 5 Select Next
13. enter the selection and 3 Select the OK button to apply all Touch Settings 26 150 7000 002 Hampshire TSHARC Control Panel Rev 6 20cs Ee xi Screen Selection Calbeation Click Settings Touch Settings Capacitive I features ace avadable default ouch sent only at touch down All other features are vadable ouch sent only at Touch Up This disables the aght puse Click option a em shall be disabled Touch Screen Tray Icon 1 If you do not want a Touch Screen Controller Icon to display in the toolbar tray go to step 3 or 2 If you want a Touch Screen Controller Icon to display in the toolbar tray select the box and 3 Select the Finish button the TSHARC drivers shall be installed Touch screen diver installation configuration is now complete Press Finish to install the touch screen driver Welcome The touch screen tay application automaticaly recaiculates Coordinates when the screer s ae resized or rotated Accept HEULA This process runs in the background and is configurable by Set Installing Touch Screen Driver co ARO pe inst Installation Finished 10 12 BIT Senal COM 1 9600 bps Firmware mv 48 Instrachora Welcome Accept HEULA install 10 12 BIT Seral COM 1 9600 bps Firmware rev 48 Installation Complete At the dialog box Setup is now complete 1 select OK exiting the TSHARC Touch Screen Controller installation
14. to a mid range setting when the unit is powered off Adjust the brightness of the Display to the lowest possible setting for a given set of conditions and display characteristics Doing so shall provide the best viewing of the image extend the lamp life of the backlight and reduce the internal heat of the Display USER TIP Select Button The Select Button is the access point to the On Screen Display OSD Source Screen Menu See On Screen Display Up Button The Up Button is an adjustment tool in the OSD Source Screen Menu See OSD Screen Menu Parameters Down Button The Down Button is an adjustment tool in the OSD Source Screen Menu See OSD Screen Menu Parameters Source Button The Source Button allows the user to switch between video signal sources attached to the Monitor Composite Video 1 2 amp 3 and VGA 16 150 7000 002 ON SCREEN DISPLAY The On Screen Display OSD user interface is the path to all display signal source adjustments The Source Screen Menu with its user friendly graphical interface provides access to fine tuning the Display OSD Source Screen Menu Activation To activate the OSD menu in the current video source press and release the SELECT button Note OSD Source Screen Menu shall close after 15 seconds of inactivity This setting can be adjusted in the OSD Source Screen Menu OSD Menu icon under OSD Duration OSD Source Screen Menu Parameters The Source Screen Menu is compri
15. vertical position for the OSD menu on the Display OSD Duration e Open the OSD Duration function and e Press the UP or DOWN buttons to adjust the time elapse between the last menu activity and when the menu disappears The range is between O and 100 seconds factory default is 15 seconds e e 6 o 6 6 06 6 9 6 6 06 6 96 06 6 6 6 6 0 06 6 6 06 6 06 6 6 0 6 6 6 06 9 06 6 6 0 6 6 06 06 06 6 0 6 6 06 6 9 6 6 6 06 6 06 6 06 6 6 6 06 9 6 6 96 6 06 6 06 9 9 6 6 6 o 6 J Set up Menu Parameters AUTO Power e Select AUTO Power function if user wants system data channel signal source saved when the system is powered off Reset e Select Reset function and e Select YES to automatically adjust picture data to default such as brightness 150 7000 002 19 E e Select System function to select the source signal type NTSC PAL and AUTO e Video 1 Composite NTSC e Video 2 Inactive e Video 3 Inactive e PC RGB and e AUTO Recommended selection Automatically assigns the correct video signal source association NOTE Source Screen Menu Category is enabled when the input signal is VGA H Position e Open the H Position function and e Press the UP or DOWN buttons to adjust the horizontal position of the screen display V Position e Open the V Position function and e Press the UP or DOWN buttons to adjust the vertical position for the screen display
16. Ground Green Video Signal Green Video Ground Blue Video Signal Blue Video Ground H SNYC V SNYC H V SYNC Ground USB RS 232 RXD USB RS 232 TXD Digital Ground RI OUT 88 569722 35P MS27467E11B35S Table 2 COMPUTER HOOK UP Computer Display Properties XGA or SVGA Prior to connecting the monitor to the computer with another monitor verify the computer display properties are set to between 640x480 and 1024 x 768 in 4 3 aspect ratio The optimum setting for viewing is 800 x 600 8 4 or 1024x768 pixels all other sizes The refresh rate must be set between 60 75Hz to eliminate screen icker CAUTION Pixel settings different from the native resolution may exhibit less precise images and Pixel settings over 1024 x 768 flash out of range with no display Setting the Display Settings Arrange Icons By Refresh 1 Right mouse click on an open area of the Daste desktop screen to bring up the Desktop Menu eke SI i Undo Move Ctrl z 2 Left mouse click on Properties to HN A Graphics Properties open the Display Properties menu opten 3 Connect to a CRT monitor to establish the New i computer display properties Properties F Display Properties Themes Desklop ScreenSaver Anne ence Settings 4 Select the Settings tab 5 Under Screen Resolution verify or slide the bar until the Screen Resolution is at 800 x 600 pixels SGVA or 1024x768 XGA Displey 6 Select the Advanc
17. connectors Front mounted controls and various mounting options makes this a user friendly display This model incorporates the latest optical engineering to achieve optimal viewability in all lighting conditions It is engineered to operate on low power consumption and may be equipped with optional Analog Resistive Touch Screen This manual contains instructions for configuring the touch screen as well 150 7000 002 SAFETY General Safety Instructions Before operating this Monitor read this User Manual thoroughly Retain this User Manual for future use Verify the computer system capability see System Set up to insure operation of the Monitor For expeditious installation follow these User Manual instructions in the sequence presented Adhere to all Caution and Warnings on system parts and as stated in this User Manual All User Manual instructions for installation and operation must be followed precisely Adjust only those controls covered by the User Manual s operating instructions improper adjustment of other controls voids the unit s warranty and may result in unit damage and Adhere to local installation codes Safety Icons Warning Shock Hazards This icon is intended to tell you of a potential risk of electrical shock WARNING lt Caution Instructional CAUTION This icon is intended to tell you of important operating and or maintenance instructions Seele Unit Safety e Always disconnec
18. difficult mount applications Locate the ball and socket system in the shipping box The kit consists of two RAM balls on mounting plates and a RAM arm with an adjustable T knob and a packet of three 3 M4 x 10 counter sunk stainless screws for mounting to the display A Mounting Holes Figure 2 Figure 3 Figure 4 150 7000 002 9 e Line up one of the ball mounting plates on these three holes Figure 4 With three 3 M4 x 10 counter sunk stainless screws attach this mounting plate to the back of the unit Mount the second ball mounting plate where the Monitor shall be installed Insert each ball into the RAM arm Lightly tighten the arm around the balls using the T knob on the arm Figure 2 4 Adjust the Monitor to the viewing preference and Tighten the T knob to hold the Monitor in position It is recommended the remaining ball be mounted on a flat surface Because of the various surface substrates the Monitor shall be mounted on the installer shall provide the screws to mount the other ball Panel Mount The panel mount installation should be specified at the time of order the ball and socket mount system will not be included in the shipping box The mounting hardware packet is included with the unit accessories in the shipping box This packet includes four 4 threaded screws approximately 7 6 cm 3 long four 4 Nylock nuts and four 4 flat washers For installation there are four tapped mounting holes
19. e This monitor has been designed to provide optimum performance and service without any required scheduled maintenance other than occasional cleaning Turn off the Monitor power before cleaning the Monitor optional Touch Screen or unit s enclosure WARNING Do not use abrasive cleaners or solvent based ammable cleaners on the Flat Panel or Touch Screen Display its enclosure or any other electrical de CAUTION vice cables power cord etc Do not use paper products as they may scratch the Display screen and Do not directly apply cleaning solutions to the Display screen Display Screen Cleaning e A vinegar based cleaner is preferred to prevent streaking and degradation of the coatings or e A non abrasive glass cleaner such as a professional foam glass cleaner e Apply the cleaning solution to a soft clean cloth dampening slightly e Keep a fresh side of the cleaning cloth towards the screen surface to avoid scratching it with accumulated grit and e To minimize the risk of abrasion to the screen air drying is recommended Disconnect cabling from the Touch Screen Display before cleaning A Touch Screen Display will be activated by cleaning the Display This may create a potentially WARNING dangerous condition Optional Touch Screen Cleaning e Follow cleaning directions above or use a special screen cleaning tissue or a solution specifically formulated for antistatic coatings e Lightly dampen a soft clean cloth w
20. e associated meda Select Controller rented materiak and onkae o electronic documentation Conf SOFTWARE PRODUCT The SOFTWARE igure PRODUCT also includes ary updates and supplements to Install the original SOFTWARE PRODUCT provided to pou by Hampshire Any solle provided along with the SOFTWARE PRODUCT Iha iz associated wth a separate enduses license agreement is Scensed lo you under the terma of Ihat license agreement By mstaling copying downloading accessing cr olhesise using the Note Any unlawful use of the TSHARC driver is a strict violation of the United States and International copyright laws Using a TSHARC driver with any third party Touch Screen is strictly prohibited lx V accent al ol the teme of the above License Agreement Select Controller 1 The TSHARC Driver is a 12 bit controller the radio button is selected by default Note A PS 2 controller interface is not available 2 Select the controller interface matching the Select Controller E cable used to install the monitor METTE udi 2 Select controlar interface type 3 Select the Autodetect button if installing the Touch Screen through a RS 232 serial OP e aa interface oe Conticlies Irterlace g E cept HEULA RER 4 There are two options for RS 232 installation ee Sein Amod Autodetect and Manual Manual instructions Configure C use are found in section Manual RS 232 Controller ae SAS Set up cor y 5 If
21. e calibrated 24 150 7000 002 to specific points on the Display screen 1 Select the Calibration tab or in ten seconds the calibration program launches unless a Multi monitor situation is present then go to section Configuring a Multi monitor Installation 2 There are three buttons Graphic Calibration and Test For default Four point calibration select the Graphic square This is the best known general calibration it compensates for skew and some edge linearity anomalies and 3 Go to section Calibration Process Custom Calibration Settings 1 To customize the calibration process select the Calibration button to bring up Calibration Options and the Offset menu 2 Select OK when calibration and or offset selections are made Calibration Options 3 Point 4 Point Calibration Calibration Point 20 Point Calibration Calibration Calibration Process Hampshire TSHARC Control Panel Rev 6 20cs E xj Screen Selection Calibration Chek Settings Touch Settings Capacitive Three Point Calibration Quick calibration of a known good Touch Screen overlay No correction is applied Four Point Calibration Compensates for skew and some edge linearity anomalies Seven Point Calibration More accurate than three point calibration No correction is applied Twenty Point Calibration Provides the highest level of Touch Screen linearization and skew correction and Offset Varied linearity exists
22. e of U S must be prepaid by receiving party Standard Limited Warranty Aydin warrants its products to be free from defects in materials for a period of Two 2 Years from the date of the original shipment from the factory Aydin agrees to repair the product without labor cost to the purchaser for a period of One 1 Year from the original ship date No other warranty is expressed or implied Specifically excluded is normal wear and tear abuse or misuse of the products Aydin does not make any claims or warrant the products with respect to the purchaser s use or application of the products Products returned but found not to be within the terms of this warranty are subject to a service fee to be paid prior to the return of the product to the purchaser Liability Any claim which may be made against Aydin with regard to this contract for sale must occur within One 1 year from date of original shipment from the factory IN NO EVENT SHALL Aydin BE LIABLE FOR LOSS OF PROFITS LOSS OF USE LEGAL OR PROFESSIONAL FEES CONSEQUENTIAL ORINCIDENTAL DAMAGE OR FOR SPECIFIC PERFORMANCE OF THE PRODUCTS THEIR MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE 150 7000 002 33
23. e press the SELECT button again to exit from the OSD Source Screen Menu or e Close the main menu all changes are saved 150 7000 002 17 New settings shall be stored in memory upon pressing the SELECT button to exit the Source OSD Source Screen Category s Function Menu If SELECT is not pressed or inactivity is detected within the 15 second factory CAUTION default OSD duration any function adjustments made shall not be saved USER TIP Brightness Before adjusting the Brightness function parameters set the LCD panel backlight brightness using the control toggle large sun small sun set to its brightest large sun button in the ambient light source e Open the Brightness function e Press the UP or DOWN buttons to set the Display s desired brightness and e Adjustments go from very dim black to 100 very bright dazzling white Contrast Contrast is the difference in brightness between the light and dark areas of the pixels of a picture e Open the Contrast function e Press the UP or DOWN buttons to set the Display s desired contrast and e Predefined minimum to maximum is in the display bar Saturation Saturation is the vividness or intensity of the hue or color e Open the Saturation function and e Press the UP or DOWN buttons to set the Display s desired saturation Tint Tint is the pinks blues and greens of the Display e Open the Tint function e Press the UP or DOWN b
24. ed button to Delat Honto an Inte 623450 Expres Chipset Fami go to the next menu to verify the Hz refresh rate Screen resolution Color quality Lass Jj Highest 32 bi vi 800 by 600 neces 150 7000 002 13 Color Management a rema Meo Accelerator Driver General Adapter Moa Troubleshoot Monitor type m Default Monitor 7 Select the Monitor tab Monitor settings 8 Under Monitor Settings verify the Screen Refresh Rate is between 60 and 75Hz Screen refresh rate 72 Hertz e f so select the Cancel button and go to step 9 e f not select a setting within the 60 75Hz range e Select the Apply button uu letat hMonmtor and mitenki 5 224 063 EXDH t mpset f Fa Color Management WA InteltA Graphics Media Accelerator Driver General Adapter Monitor Troubleshoot ll M Monitor Settings s Your desktop has been reconfigured Do you want to keep 9 At the Monitor Settings dialog uy these settings box select Yes to accept the new desktop view settings Reverting in 12 seconds 10 In the Display Properties dialog 72 Henz box verify the Screen Resolution is eer E at 800 x 600 SVGA or 1024x768 Clearing this check box allows you to select display modes that this AGAJ ee ee i ee 11 Select the Apply button a Cae Pe 14 150 7000 002
25. facturer s web site or contact the manu facturer for instructions to uninstall drivers Reinstall the TSHARC Driver software 30 150 7000 002 APPENDIX C Display Sunlight Readable Dimming Ratio Wide Range DC Power Input Power Consumption Power Conditioning Technical Specifications 10 4 V OPTIONAL 1024 x 768 XGA Display V OPTIONAL 1024 x 768 XGA Display TFT AM SVGA LCD 262K Colors 800 x 600 pixels 1024 x 768 XGA Display Standard 1400 nits NVIS 1000 nits MIL L 85762A AF Open Canopy 1000 1 m Connectors Video Input Amphenol MIL DTL 38999 Series Power Input Amphenol MIL C 26482 Series Milled AL Black Hard Anodized SAE AMS 2469 E Other Coatings MIL C 22750 RAM Mount Standard Flush Panel 19 Rack Optional 8 36 VDC 12 24 28 VDC nominal MIL STD 1275D 6 Watts Min 6 Watts Min 20 Watts Max 35 Watts Max Internal Short Circuit Protection Load Dump Protection Over Voltage Protection Reverse Polarity Protection 150 7000 002 31 Environmental Specifications 10 4 Operating 40 C to 70 C 40 F to 158 F Temperature MIL STD 810F 501 4 502 4 II Op Storage 40 C to 75 C 40 F to 167 F Temperature Vibration 5 8 G 5 500 Hz IP67 NEMA 6 Submersible Humidity owe Sunlight Readability for Buttons co Us E 32 150 7000 002 Aydin offers it s products and services for sale under the fol
26. g in 800 x 600 or 1024x768 pixel Press the arrow down button one time to auto resolution adjust the display Verify the video display settings match the monitor and 60 75Hz refresh rate Proper cable grounding and shielding Verify the use of a proper video cable with suitable grounding and shielding Keep the video cable away from sources of EMI and RF Improper video display settings Check signal source for proper signal Check for proper display properties selection of the display pixel setting Verify the display refresh rate 60 75Hz Display unit is farther than 3 m 10 ft from Single cable lengths should be of high quality signal source shielded VGA cable Contact Aydin for infor mation on custom cables Multiple Monitors are driven from the same Splitting the video signal divides the strength signal source of the signal A video signal booster line driver is recommended if installation requires more than one Monitor driven from a single video source Monitor has incorrect or bad sync signals Check for proper video cable installation or replace suspected faulty cable Check the video source is within the display s operating range max 1280x1024 pixels and 60 75Hz 150 7000 002 29 Symptom Display image is not properly sized Possible Problem Solution OSD adjustments need to be made Adjust the vertical and horizontal size controls through the OSD Improper video display settings Check for pro
27. he Monitor is being installed and e Upon installation verify the power connector is securely seated on the unit Ratings and Grounding This unit may be operated from an 8 36 VDC power source e Use the supplied power cable and e Always connect to a properly grounded power source Protection on Servicing Servicing User e User care is limited to cleaning the exterior of the unit e Do not disassemble or modify the unit or cables to avoid the possibility of an electrical shock damage to electrical components or scratching the Display surface and e Disassembly voids the warranty Servicing Aydin Displays Qualified Service Personnel may be required if the unit e Does not operate normally when installation instructions are followed e Does not operate normally when operating instructions are followed e Has been dropped or damaged or e Exhibits a distinct change in performance indicating a need for service Shipping If the unit should need to be shipped to the Aydin Displays Service Center the original packing material should be used to insure safety in shipping Repack the unit as it would have originally been received from Aydin Displays Radio Frequency Interference CAUTION This equipment generates uses and can radiate radio frequency energy If not installed with the units accompanying cables it may cause harmful interference to radio communications 150 7000 002 5 PRODUCT CARE AND MAINTENANCE Product Car
28. ith water vinegar based cleaner or a general purpose mild detergent solution e Keep a fresh side of the cleaning cloth towards the screen surface to avoid scratching it with accumulated grit and e To minimize the risk of abrasion to the screen air drying is recommended Monitor Enclosure e Clean the unit enclosure with a soft clean cloth lightly dampened with a general purpose mild detergent solution e To rinse wipe down with clean water and e Dry with a soft clean cloth 6 150 7000 002 To avoid risk of electrical shock do not disassemble the unit s enclosure Users cannot service the Monitor User maintenance is restricted to cleaning as ex WARNING plained Disassembling the unit voids the warranty Long term Storage e For long term storage it is suggested the unit be stored in a normal indoor environ ment and the Display glass be protected from accidental damage e For pedestal mount units disconnect the cable s and loosen the arm adjustment to a point where the ball can be removed from the arm or e For Flush or Panel Mount units cover the product with a protective covering that shall not scratch or transfer any dyes to the Display screen Maintenance E SSS Ss Cord WARNING To avoid shock and fire hazards replaced the unit s power cord if e Insulation becomes damaged or e A loose connection is suspected Other Maintenance Only Aydin Qualified Service Personnel shall perform all maintenance excep
29. lowing terms and conditions Any and all orders will be accepted only at the sole discretion of Aydin and under these terms and conditions Any modification to these terms and conditions can only be made by Aydin in writing Agreement to any modifications must be made by all participants of the sale prior to the acceptance of any order Prices All published prices are in effect from the date noted on the price sheet Prices are subject to change without notice Written quotations may be requested Written quotations are valid for 30 days All prices are quoted in U S dollars Any and all taxes tariffs currency translations duties insurance freight charges and any other handling charges are the responsibility of the purchaser and must be prepaid and or charged Acceptance All orders will be accepted at the sole discretion of Aydin Any order can be rejected for any reason at any time without liability Payment All purchasers must prepay the order accept COD shipment or arrange for other acceptable methods of guaranteed payment credit card cash prepayment etc before any order will be shipped VISA MasterCard DiscoverCard and American Express are welcomed and encouraged Shipments All shipments are FOB Scottsdale Arizona Purchaser is encouraged to provide Aydin with shipping authorization on their freight account Unless otherwise specified Aydin will select the best way for shipment using common carrier FedEx
30. lugged into the VGA video connector Verify a video signal is coming out of the computer i e plug into a known good display source Verify the incoming signal source selected matches the Monitor signal source Composite S Video VGA Check the Brightness front panel setting on the Monitor This may be set too low Check the Brightness and Contrast controls in the OSD These may be set too low Computer may have gone into power manage ment stand by Press any key on the keyboard move the mouse or cursor or it there is the Touch Screen option touch the screen to wake up the computer 28 150 7000 002 Symptom Display has rolling bars across the screen or vertical shaded bars on the image Possible Problem Solution VGA video display is not set to view at 800 x Verify the computer video display settings of 600 pixels or 1024x768 pixels the signal are set to match the display and 60 75Hz refresh rate Defective video cable On a known good display source confirm the video cable is not defective Interference from adjacent equipment For proper grounding and shielding verify use of a proper video cable Keep the cable away from sources of EMI such as electric motors or unshielded RF sources such as radar and microwave Horizontal size is not adjusted In the OSD adjust the horizontal size controls Symptom Picture quality image stability is distorted Possible Problem Solution Not workin
31. per display properties selection of the display settings Monitor autosize will only display full screen if source is 4 3 aspect ratio VGA signal source Auto Adjust needs The VGA source is able to auto adjust the activated Monitor to its optimum viewing setting Press the arrow down button one time to auto adjust the display Symptom Touch Screen T S does not respond Possible Problem Solution T S cable is not plugged in Verify the connections between the T S and the computer T S cable is installed in a different COM port Install the T S into another COM port If using than installed by the software a laptop verify the COM port s is enabled T S controller driver has not been installed Install the TSHARC controller driver Hardware failure Contact an Aydin Technical Support Technician 610 404 5370 Symptom 7 S moves but does not follow a finger or stylus Possible Problem Solution Controller is not calibrated Run the calibration in the TSHARC Control Panel software T S Controller Driver is not installed Install the TSHARC Controller Driver T S cable is not installed correctly Verify the T S cable is installed correctly Symptom Error in Calibration message appears Possible Problem Solution The T S Controller Driver is not installed Uninstall the driver using TSUN10 exe If a correctly previous T S Controller Driver was installed all footprints must be removed Go to the T S manu
32. s folder gt Left double mouse click on TSUN10 exe to execute the uninstall utility gt Follow the instructions Note The dialog box stating it is removing all Touch Screen Drivers from the computer means it is removing all TSHARC drivers Other Touch Screen Drivers must be uninstalled with their manufacturer s uninstall utility File Download Do you want to open or save this file From the Aydin Website a Name UniWinDriver 20cs zip Go to www aydindisplays com une We BAGS From www hampshirecompany com a Open Sav C navigate to Customer Service Open jJ Ul cance then Touch Driver Downloads v Always ask before opening this type of file While files from the Internet can be useful some files can potentially harm your computer If you do not trust the source do not open or save this file What s the risk Note The dialog box stating it is removing all Touch Screen Drivers from the computer means it is removing all TSHARC drivers Other Touch Screen Drivers must be uninstalled with their manufacturer s uninstall utility 150 7000 002 21 puter it must be completely removed before installing the TSHARC Note The typical driver uninstall program or Microsoft s remove program utility does not remove all tracks of the Touch Screen Driver program Contact the manufacturer of the previ ously installed driver program to learn how to completely uninstall their product These instructions may be
33. sed of six icons each representing distinct source screen categories and their corresponding functions menu with adjustable settings Picture Menu Source Menu OSD Menu Set up Menu Inactive OSD Tools Men Parameter Adjustments e To choose a Display Parameter Category use the UP right or DOWN left buttons to move across the Source Screen Menu e As each Category icon is highlighted its related Functions Menu appears in a drop down box e To activate a Display Parameter Category move the highlight box over its icon and single press the SELECT button e n the Functions Menu a highlight bar is superimposed over the first function e Press the UP or DOWN buttons to move the highlight bar through the related Functions Menu e Single press the SELECT button to choose a Related Functions Menu item when it is highlighted e A smiley face appears to the left and a new color bar appears on the Function indicating the Category is active its parameters can be adjusted e The adjustment controls are the UP and DOWN buttons which increase or decrease the value of the parameter as noted in the percentage bar e Create the new parameter value e Single press the SELECT button to save the new value this returns the user to the Source Screen Menu e Exit from the Function Menu e To choose another Display Parameter Category use the UP right or DOWN left buttons to move across the Source Screen Menu and follow the above instructions Or e Singl
34. t for the power cord replacement described above 150 7000 002 7 SYSTEM SET UP System Requirements The computer must have this capability 8 4 800 x 600 SVGA 10 4 1024 x 768 XGA 12 1 1024 x 768 XGA 15 0 1024 x 768 XGA e f the optional Touch Screen Display is ordered an available COM port for the connector is required Shipping Box Contents The display is shipped in a custom box with custom foam packaging We recommend you save the box and all packaging materials in case the unit would need to be returned to the Aydin Displays Service Center In the shipping box you shall find e CFP 8 4 10 4 12 1 or 15 0 e Custom Power Cable e Custom VGA Cable e Mounting System and Hardware e Touch Screen Cable if the optional Touch Screen is ordered e USB Cable if the optional USB Pass through is ordered and e Optional Touch Screen Drivers located on Aydin website Figure 1 8 150 7000 002 INSTALLATION The display is designed to be mounted with a universal ball and socket mounting kit in a flat panel or optional flush mount configuration Optional Pedestal Mount The display can be supplied with a RAM universal ball and socket system mounting kit Figure 2 By installing the monitor with this kit the user can quickly adjust the viewing angle to improve viewability in changing environments This ball and socket system has proven to be successful in supporting an extreme amount of weight in high vibration and
35. t the unit from the power source before cleaning Do not operate the unit with a damaged cord Do not operate if the unit has been dropped or damaged The unit needs inspected by qualified Aydin Service Personnel Position the power cord so it shall not be in contact with hot surfaces Do not allow anything to rest on the power cord and Do not place the power cord where there shall be foot traffic TN General Safety Precautions WARNING Power cord must be connected to a properly wired and grounded power source Any equipment to which the unit shall be attached must also be connected to properly wired and grounded power sources Do not connect or disconnect the unit during an electrical storm Do not remove the unit covers there are no user serviceable parts in the unit Do not disassemble or modify the unit to avoid the possibility of electrical shock damage to electrical components or scratching the Display surface and Disassembly of the unit voids the warranty 150 7000 002 Fluids from LCD Display CAUTION If the Monitor should ever become shattered do not touch fluids from an LCD Display If fluid should get on hands or clothing immediately wipe off with liquid soap or rubbing alcohol wash with water consult with a doctor and If fluid gets in the eyes flush eyes immediately with water for a minimum of 15 minutes consult with a doctor Electrical Safety Connecting Cables e Disconnect the power to the computer when t
36. uttons to set the Display s desired tint and e Ranges on the Display bar are low pinks mid range blues and upper greens Sharpness e Open the Sharpness function e Press the UP or DOWN buttons to select a desired sharpness for the Display and e Sharpness choices in the Display bar are preset at O 33 66 and 100 Auto Color e Auto Color is best calibrated from an all white background From the VGA video source create an all white background e Open the Auto Color function e Press the SELECT button to run the Auto Color Setup Repeat twice and e When complete press the SELECT button to save the changes and exit 18 150 7000 002 A check in a box indicates an enabled signal source attached to the monitor Deselecting the box disables the monitor s ability to display the signal Video 1 Composite e Open the Video1 function and e Press the UP or DOWN buttons to enable ON or disable OFF the Video 1 source Video 2 INACTIVE or if connected as above Video 3 INACTIVE or if connected as above PC VGA e Open the PC function and e Press the UP or DOWN buttons to enable ON or disable OFF the PC source OSD H Position e Open the OSD H Position function and e Press the UP or DOWN buttons to adjust the horizontal position for the OSD menu on the Display OSD V Position e Open the OSD V Position function and e Press the UP or DOWN buttons to adjust the
Download Pdf Manuals
Related Search