TRANS-C5200 and TRANS-C5201 User`s Manual
Contents
1. H 1 5 0V The TRANS C5201 module has socketed resistors for the RS485 RS422 120 Ohm termination resistors The socketed resistors are 8 pin isolated network SIP resistors Since the SIP resistors contain 4 isolated resistors the polarity indicators are not required Refer to table 1 5 to correlate the resistors for each channel grouping Acromag recommends that termination resistors are present for any Field input TRANS C5201_ PMC SLOT A PMC SLOT B Ch 0 3 R1 R9 Ch 4 7 R2 R10 Ch 8 11 R3 R11 Ch 12 15 R4 R12 Ch 16 19 R5 R13 Ch 20 23 R6 R14 Ch 24 27 R7 R15 Ch 28 31 R8 R16 Acromag Inc Tel 248 295 0310 Fax 248 624 9234 Email solutions acromag com http www acromag com TRANS C5200 C5201 Users Manual H The TRANS C5200 and TRANS C5201 boards are designed to be VHDL INTERFACE used in conjunction with Acromag s PMC LX SX amp PMC VLX VSX VFX models The Engineering Design Kit EDK for each product does not support the proper interface for either the TRANS C5200 or TRANS C5201 The EDK currently defines the PMC Rear I O as LVDS I O Both of these boards required that the Rear I O on the PMC modules be redefined to 2 5V CMOS The Pin out table provided in the Appendix at the end of this manual links the FPGA connections to the functionality of both of these boards The TRANS C5200 model requires a tri state interface between t2. 0 6 5 6 6 5 4 2 1 4 3 8 8 6 5 2 2 9 8 6 5 0 9 3 2 2 2 8 7 0 6 5 9 L21 L20 J22 K21 K23 K22 G23 H23 AC28 AD27 AE27 AE26 AB28 AA28 AB25 AB26 AB27 AC27 AG25 AC24 AA25 AA26 AD24 AE24 Y24 AA24 AG18 AF19 AD26 AD25 AH14 AH13 AH12 AG13 AH17 AG16 AH15 AG15 AH18 AG17 AG22 AH22 AH20 AH19 AG27 RP_IO6 RNIO7 RNO RP_IO12 RNIO13 RP_IO14 RNIO15 RP_IO16 RNIO17 RP_IO18 RNIO19 RP_IO20 RNIO21 RP_IO22 RN_IO23 RP_1024 RN_IO25 RP_IO26 RN_IO27 RP_IO28 RN_IO29 RP_IO30 RP_1044 13 APPENDIX PMC LX SX amp PMC VLX VSX VFX Pin out Table Continued This table links the TRANS C520x modules to the PMC LX SX amp PMC VLX VSX VFX The LX SX amp VLX VSX VFX Schematic Signal column corresponds to the signal name of that pin on the PMC LX SX schematic or PMC VLX VSX VFX that was provided in the EDK The V4 Pin column represents the pin number of the Virtex 4 FPGA that is routed to the Rear I O Note that to support these transitions modules the Rear I O signals must be defined as 2 5V CMOS The V5 Pin column represents the pin number of the Virtex 5 FPGA that is routed to the Rear I O Note that to support these transitions modules the Rear I O signals must be defined as 2 5V CMOS The TRANS C5200 Schematic signal column corresponds to the signal name of that pin on the TRANS C5200 schematic Note that the numer
3. Digital Channels Default to a high impedance state Pull up Resistors 6800 Socketed bussed SIP pull up resistors are installed in banks of 8 Channels 0 7 8 15 etc With SIP removed a nominal 47 5KQ pull up are always present Each bank of eight can be selectively pulled up to either 3 3V or 5V via a jumper e Digital I O DC Electrical Characteristics w 6800 Pull ups e Input Voltage Range 0 25V to 3 55V 3 3Vterm or 0 25V to 5 25V 5 0Vterm e Vu 2 2V minimum e Vit 0 8V maximum e Vou 3 1V typical 3 3V pull up e Vou 4 8V typical 5 0V pull up e Vo 0 3V typical 0 4V max 12mA e Turn On Time to logic low 125nS Typical e Turn Off Time 8900 pull ups 500nS Typical Channel Configuration 2 PMC sites each with 32 channels of Bi directional EIA 485 422 I O Differential signals are independently direction controlled e 1 5 V Min 3 3V Max Differential Driver Output Voltage with 540 load e 3VMax Common Mode Output Voltage e 0 2 Min to 0 05 Max Differential Input Threshold Voltage 7V lt Vcm lt 12V e 15mV Typical Input Hysteresis e 96KQ Minimum Input Resistance The receiver contains a fail safe feature that results in a logic high output state if the inputs are unconnected floating or shorted e Driver Input to Output Delay 27ns Typical 40ns Maximum e Receiver Input to Output Delay 33ns Typical 60ns Maximum Termination Resistors 120 Ohm socketed SIP termination resistors in groups
4. of 4 Channels 0 3 4 7 etc Fax 248 624 9234 Email solutions acromag com http www acromag com TRANS C5200 C5201 User s Manual LX SX amp VLX VSX VFX Sch Signal V4 V5 Pin G G F2 E2 H H E D G G F F H H H G G G H H F2 E E E A A B B B A D D D C C D C B2 C C A2 A E E G1 TRANS C5200 TRANS C5201 Pin Schematic Signal Schematic Signal DATAOO DIROO DATAO1 DIRO1 DATA02 DIR02 IDATAO3 DIR03 DATA04 DIR04 DATA05 DIRo5 DATA06 DIR06 DATAO7 _ DIR07 DATA08 DIR08 DATA09 DIR09 DATA10 DIR10 DATA12 DIR12 DATA13 DIR13 DATA14 DIR14 DATA15 DIR15 DATA16 DIR16 DATA17 DIR17 DATA18 DIR18 DATA19 DIR19 DATA20 DIR20 DATA21 DIR DATA22 DIR22 DATA23 DIR23 DATA24 _ DIR24 DATA25 DIR25 IDATA26 DIG DATA27 DIR27 DATA28 _ DIR28 DATA29 DIR29 DATA30 DIR30 DATA32 _ DATA00 DATA33 _ DATA01 DATA34 _ DATA02 DATA35 DATA DATA36_ _ DATA04 DATA37 _ DATA05 DATA38 _ DATA06 DATA39 DATA07 DATA40 DATA08 DATA41 _ DATA09 DATA42 DATA10 DATA43 DATA11 DATA44 _ DATA12 N l k 4 S Be D a 2 BN 1017 2 RP_lO12 RN_1013 RP_1014 RN_1015 RP_lO16 BN 1017 BP 1018 BN 1019 RP_lO20 RN_1021 BP 1022 BN 1022 RP_1024 BN 1025 BP 1026 BN 1027 BP 1028 BN 1029 BP 1020 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 k k k l k sk lA 2 2 2 2 2 2 2 1 0 0 4 3 4 3 4 3 2 1
5. use in the event the product must be shipped This board is physically protected with packing material and electrically protected with an anti static bag during shipment However it is recommended that the board be visually inspected for evidence of mishandling prior to applying power Refer to the specifications for loading and power requirements Be sure that the system power supplies are able to accommodate the power requirements of the system boards plus the installed Acromag board within the voltage tolerances specified Adequate air circulation must be provided to prevent a temperature rise above the maximum operating temperature and to prolong the life of the electronics If the installation is in an industrial environment and the board is exposed to environmental air careful consideration should be given to air filtering The board is non isolated since there is electrical continuity between the CompactPCI bus and PMC module grounds As such the field I O connections are not isolated from the system Care should be taken in designing installations without isolation to avoid noise pickup and ground loops caused by multiple ground connections 9 2 0 PREPARATION FOR USE UNPACKING AND INSPECTION ro Wy AUTION SENSITIVE ELECTRONIC DEVICES DO NOT SHIP OR STORE NEAR STRONG ELECTROSTATIC ELECTROMAGNETIC MAGNETIC OR RAQIOACTIVE FIELDS WARNING This board utilizes static sensitive components and should only b
6. Acromag N TRANS C5200 C5201 CompactPCI Rear Transition Modules USER S MANUAL ACROMAG INCORPORATED Tel 248 295 0310 30765 South Wixom Road Fax 248 624 9234 P O BOX 437 Wixom MI 48393 7037 U S A Copyright 2009 Acromag Inc Printed in the USA Data and specifications are subject to change without notice 8500 826 A09B000 2 TRANS C5200 C5201 User s Manual TABLE OF IMPORTANT SAFETY CONSIDERATIONS You must consider the possible negative effects of power wiring CONTENTS component sensor or software failure in the design of any type of control or monitoring system This is very important where property loss or human life is involved It is important that you perform satisfactory overall system design and it is agreed between you and Acromag that this is your responsibility 1 0 General Information The information of this manual FIELD 1 0 CONNECTORG lt x s sss x Ke Ke eee Ke ee 3 may change without notice RESISTOR JHUMPER CONFIGURATIONG 6 Acromag makes no warranty VHDL INTERFACE sss ss s e x e c x ee e neee 7 of any kind with regard to this material including but not 2 0 Preparation For Use limited to the implied warranties of merchantability UNPACKING AND INSBECTION ee oaenee 9 20A INESE Joie Palticulal CARD CAGE CONSIDERATIONG 0 s0s0 9 purpose Further Acn omag Non lsolation Considerations 5 9 assumes no responsibility for any errors that may appear in
7. IELD I O CONNECTORS Table 1 2 TRANS C5200 DIGITAL Board Field O Pin Pin Description Pin Pin Description Connections COMMON _ _ 1 COMMON Digital Channele 5 Digital Channel7 Digital Channel 8 6 Digital Channel9 Digital Channel 12 8 DigitalChannel 13 Digital Channel 14 9 Digital Channeli5s Digital Channel 36 Digital Channel 37 O oloon O Ln O1 O1 Gn O1 Gn OF OT alal BY l BR BY l BY BY BY BR BR CO GO CO CO N Ol eA OO PO OO CO N OD Qm A GO PO CO CO CO NY OD OT BY CO PO CO Ol CO NI On Acromag Inc Tel 248 295 0310 Fax 248 624 9234 Email solutions acromag com http www acromag com TRANS C5200 C5201 Users Manual 5 FIELD I O CONNECTORS SCSI 3 68 Pin Female Connector Table 1 3 TRANS C5201 Fin Description Pin pin Description Pin DIFFERENTIAL Board Field 35 1O Pin Connections 36 37 38 C Diferential gnac 6 Differential Che Diferential Ches 8 Diferential Che Diferential cn7 TS Diferemial Chr Diferential gnas 26 Diferential haa Diferential cha7 29 Diferential Ch27 Differential Ch28 30 Diferential Ch28 O O D G G o O1 O1 O1 OF Gn OF Gn OF Qn Qni BH BH BY BR AR BR BR BR BR BR OO N oj BR OO Po CO NIIA A GO PO CO CO CO NY OD Qm BY CO PO CO GO Acromag Inc Tel 248 295 0310 Fax 248 624 9234 Email solutions acromag com http Awww acromag c
8. e handled at a static safe workstation CARD CAGE CONSIDERATIONS IMPORTANT Adequate air circulation must be provided to prevent a temperature rise above the maximum operating temperature Non lsolation Considerations Acromag Inc Tel 248 295 0310 Fax 248 624 9234 Email solutions acromag com http Awww acromag com 10 3 0 SERVICE AND REPAIR SERVICE AND REPAIR ASSISTANCE PRELIMINARY SERVICE PROCEDURE CAUTION POWER MUST BE TURNED OFF BEFORE REMOVING OR INSERTING BOARDS WHERE TO GET HELP www acromag com TRANS C5200 C5201 Users Manual Surface Mounted Technology SMT boards are generally difficult to repair It is highly recommended that a non functioning board be returned to Acromag for repair The board can be easily damaged unless special SMT repair and service tools are used Further Acromag has automated test equipment that thoroughly checks the performance of each board When a board is first produced and when any repair is made it is tested placed in a burn in room at elevated temperature and retested before shipment Please refer to Acromag s Service Policy Bulletin or contact Acromag for complete details on how to obtain parts and repair Before beginning repair be sure that all of the procedures in Section 2 Preparation For Use have been followed Also refer to the documentation of your carrier CPU board to verify that it is correctly configured Replacement of the board with one that is kno
9. emale connector 110 contacts with upper shield 68 pin SCSI 3 female receptacle header AMP 787082 7 or equivalent Operating Temperature 40 to 85 C Relative Humidity 5 95 Non Condensing Storage Temperature 55 C to 100 C Also designed to meet the following environmental standards per ANSI VITA47 2005 R2007 Vibration Class V2 Shock 20g Environmental Class EAC6 Operating Temperature AC3 40 to 70 C Non lsolated CompactPCI and field commons have a direct electrical connection TRANS C5200 3 3 VDC 5 Typical TBD mA Max TBD mA 5 0 VDC 5 Typical TBD mA Max TBD mA TRANS C5201 3 3 VDC 5 Typical TBD mA Max TBD mA 5 0 VDC 5 Not Used 11 SPECIFICATIONS PHYSICAL Connectors ENVIRONMENTAL POWER REQUIREMENTS 1 Note that all power is drawn from the AcPC4620CC E Carrier board Acromag Inc Tel 248 295 0310 Fax 248 624 9234 Email solutions acromag com http www acromag com 12 TRANS C5200 DIGITAL I O OPEN DRAIN Digital I O DC Electrical Characteristics TRANS C5201 DIFFERENTIAL I O EIA 485 422 Differential I O Electrical Characteristics Differential Propagation Delay Termination Resistors Acromag Inc Tel 248 295 0310 TRANS C5200 C5201 User s Manual OPEN DRAIN Channel Configuration 2 PMC sites each with 64 Channels of open drain I O Note that the open drain architecture does not require direction control Reset Power Up Condition All
10. g A this manual and makes no 3 0 Service and Repair commitment to update or keep current the information SERVICE AND REPAIR ASSISTANCE TTEETETETITETTIT 10 contained in this manual No PRELIMINARY SERVICE PROCEDURE 10 part of this manual may be WHERE TO GET HELP 2 2cseeeeeeeeeeeeeeeeees 10 copied or reproduced in any form without the prior written consent of Acromag Inc 4 0 Specifications PHYSICAL as a 042 ote Rer Ted TRE ad A A 11 ENVIRNOMENTAL 020 cceeeeee eee eeeeeneees 11 POWER REQUIREMENTG 222eceeeeeeeees 11 TRANS C5200 DIGITAL lO ss sss sss esse eee 12 TRANS C5201 DIFFERENTIAL UO sss sss ss sss e ses 12 APPENDIX PMC LX SX amp PMC VLX VSX PIN OUT TABLE 13 CERTIFICATE OF VOLATILITY 15 Trademarks are the property of their respective owners Acromag Inc Tel 248 295 0310 Fax 248 624 9234 Email solutions acromag com http www acromag com TRANS C5200 C5201 User s Manual 3 The TRANS C5200 and TRANS C5201 are rear transition modules for 1 0 GENERAL Acromag s ACPC4620E CC CompactPCI carrier cards The modules are available for use in card cages which provide rear exit for I O connections INFORMATION via 80 mm wide transition modules transition modules can only be used in card cages specifically designed for them They are double height 6U single slot module and adheres to the CompactPCI mechanical dimensions and IEEE Standard 1101 11 1998 with a p
11. he FPGA and the TRANS C5200 This allows for bi directional communication without the requirement for a direction control signal Each I O point can be either inferred using process statements or use the IOBUF Xilinx primitive Note that the IOSTANDARD LVCMOS25 must be assigned to every pin in the ucf file An example 3 state process VHDL statement is below RIO_DATAO Top level I O point Example VHDL for TRANS RIO_DIRO Direction control where output 1 C5200 DATAO_OUT Output from FPGA logic DATAO_IN Input to FPGA logic process DATAO_OUT RIO_DIRO 3 state output begin if RIO_DIRO 1 and DATAO_OUT 0 then RIO_DATAO lt 0 else RIO_DATAO lt Z end if end process DATAO_IN lt RIO_DATAQ Input signal requires debounce Note that due to the slow rising time of the signal greater then 125nS debounce is required for each input Debounce will filter out any incidental transition caused by the slow rise time of the input signal Example debounce VHDL is available upon request Acromag Inc Tel 248 295 0310 Fax 248 624 9234 Email solutions acromag com http Awww acromag com 8 VHDL INTERFACE Example VHDL for TRANS C5201 TRANS C5200 C5201 User s Manual The TRANS C5201 interface uses one directional control signal and one I O bit for each RS485 RS422 I O signal Each I O point can be either inferred using process statements or use the OBUF Xilinx primitive for the direction line
12. ical value following DATA correlate directly to the Open Drain I O on the 68 pin I O connector The TRANS C5201 Schematic signal column corresponds to the signal name of that pin on the TRANS C5201 schematic Note that the numerical value following DATA correlate directly to the RS485 RS422 channel number on the 68 pin I O connector A direction control value of 1 sets the channel as an output A direction control value of 0 sets the channel as an input Acromag Inc Tel 248 295 0310 Fax 248 624 9234 Email solutions acromag com http Awww acromag com 14 PMC LX SX amp PMC VLX VSX VFX Pin out Table Continued TRANS C5200 C5201 User s Manual Stee r v4 v5 TRANS C5200 TRANS C5201 Sch Signal Pin Pin Schematic Signal Schematic Signal F19 AG26 DATA45 A24 AF24 DATA46 A23 AG25 DATA47 Acromag Inc Tel 248 295 0310 Fax 248 624 9234 Email solutions acromag com http www acromag com TRANS C5200 C5201 User s Manual 1 5 Certificate of Volatility Acromag Model Manufacturer TRANS C5200 Acromag Inc TRANS C5201 30765 Wixom Rd Wixom MI 48393 Volatile Memory Does this product contain Volatile memory i e Memory of whose contents are lost when power is removed Yes m No Type SRAM SDRAM etc Size User Function Process to Sanitize Modifiable Yes No Type SRAM SDRAM etc Size User Function Process to Sanitize Modifiab
13. le o Yes No Type SRAM SDRAM etc Size User Function Process to Sanitize Modifiable o Yes o No Non Volatile Memory Does this product contain Non Volatile memory i e Memory of whose contents is retained when power is removed Yes m No Type EEPROM Flash etc Size User Function Process to Sanitize Modifiable Yes o No Type EEPROM Flash etc Size User Function Process to Sanitize Modifiable Yes No Acromag Inc Tel 248 295 0310 Fax 248 624 9234 Email solutions acromag com http www acromag com
14. om 6 RESISTOR JUMPER CONFIGURATIONS Table 1 4 TRANS C5200 Socketed 680 Ohm 5V 3 3V Selectable Pull up Resistors Jumpers Resistor and Jumper locations are marked on the board Figure 1 1 TRANS C5200 Jumper Settings All jumpers are set to 5V at the factory Table 1 5 TRANS C5201 Socketed 120 Ohm Differential Termination Resistors Resistor locations are marked on the board TRANS C5200 C5201 User s Manual The TRANS C5200 module has socketed resistors for the single ended open drain pull ups There are also jumpers for selecting either 5V or 3 3V power supply for the pull ups The socketed resistors are 9 pin bussed SIP resistors pin 1 common When placed on the board pin 1 of the SIP resistors must be orientated properly as noted by the pin 1 indicator on the board Refer to table 1 4 to correlate the resistors and jumpers for each channel grouping TRANS C5200 PMC SLOT A PMC SLOT B Ch 0 7 R6 J6 R14 J14 Ch 8 15 R7 J7 R15 J15 Ch 16 23 R8 J8 R16 J16 Ch 24 31 R9 J9 R17 J17 Ch 32 39 R10 J10 R18 J18 Ch 40 47 R11 J11 R19 J19 Ch 48 55 R12 J12 R20 J20 Ch 56 63 R13 J13 R21 J21 Figure 1 1 displays the jumper settings from the TRANS C5200 modules Pin 1 is indicated on the module Note that a jumper MUST BE PRESESNT for each group of eight channels If no jumper is present then an external pull up is required for the open drain I O Jumper Selections 3 3V
15. rinted circuit board depth of 80mm which is a standard transition module depth These boards are designed to be used with the PMC LX SX and PMC VLX VSX VFX Reprogrammable FPGA modules The TRANS C5200 converts the 2 5V Rear I O signals to 64 5V 3 3V selectable Open drain I O The TRANS C5201 coverts the 2 5 Rear I O signals to 32 RS485 RS422 I O Table 1 1 CompactPCI Rear Board Size O Transition modules TRANS 4610 3U Pass through TRANS 4620 6U Pass through TRANS C5200 6U 64 5V 3 3V selectable open drain I O TRANS C5201 6U 32 RS485 RS22 I O The TRANS modules connections are made to Acromag FIELD I O ACPC4620E CC carrier field I O connections through the rear via J3 and J5 for two PMC mezzanine I O module cards Slot A amp Slot B Power is CONNECTORS also provided through these connectors Refer to the AcPC4620E CC User s Manual for further information on the J3 J5 connectors The Field I O Connections are made via two 68 pin SCSI connectors one for each PMC module Table 1 2 indicates the pin assignments for the Field I O signal mapping of the TRANS C5200 digital transition board Table 1 3 indicates the pin assignments for the Field I O signal mapping of the TRANS C5201 differential transition board The SCSI 68 Field I O pin out is the same for both PMC Slot A and PMC Slot B Acromag Inc Tel 248 295 0310 Fax 248 624 9234 Email solutions acromag com http Awww acromag com 4 TRANS C5200 C5201 User s Manual F
16. s and the IOBUF Xilinx primitive for I O lines Note that the IOSTANDARD LVCMOS25 must be assigned to every pin in the ucf file An example VHDL statement is below A direction control output of logic high 1 will set the corresponding differential signal as an output A direction control output of logic low 0 will set the corresponding differential signal as an input RIO_DATAO Top level I O point DATA0 OUT Output from FPGA logic DATAO_IN Input to FPGA logic RIO_DIRO Direction control where output 1 process DATAO_OUT RIO_DIRO 3 state output begin if RIO_DIRO 1 then RIO_DATAO lt DATAO_OUT else RIO_DATAO lt Z end if end process DATAO_IN lt RIO_DATAO Acromag Inc Tel 248 295 0310 Fax 248 624 9234 Email solutions acromag com http www acromag com TRANS C5200 C5201 User s Manual Upon receipt of this product inspect the shipping carton for evidence of mishandling during transit If the shipping carton is badly damaged or water stained request that the carrier s agent be present when the carton is opened If the carrier s agent is absent when the carton is opened and the contents of the carton are damaged keep the carton and packing material for the agent s inspection For repairs to a product damaged in shipment refer to the Acromag Service Policy to obtain return instructions It is suggested that salvageable shipping cartons and packing material be saved for future
17. wn to work correctly is a good technique to isolate a faulty board If you continue to have problems your next step should be to visit the Acromag worldwide web site at http www acromag com Our web site contains the most up to date product and software information Choose the Support hyperlink in our website s top navigation row then select Embedded Board Products Support or go to http www acromag com subb_support cfm to access e Application Notes Frequently Asked Questions FAQ s Knowledge Base Tutorials Software Updates Drivers An email question can be submitted from within the Knowledge Base or through the Contact Us hyperlink at the top of any web page Acromag s application engineers can also be contacted directly for technical assistance via telephone or FAX through the numbers listed at the bottom of this page When needed complete repair services are also available Acromag Inc Tel 248 295 0310 Fax 248 624 9234 Email solutions acromag com http www acromag com TRANS C5200 C5201 User s Manual Physical Configuration Height Depth Board Thickness Unit Weight Model TRANS C5200 Model TRANS C5201 J3 J5 CompactPCI Rear I O P1 P2 Field 1 0 6U CompactPCI Rear Transition Board 9 187 inches 233 35 mm 3 150 inches 80 0 mm 0 063 inches 1 60 mm TBD pounds TBD Kg TBD pounds TBD Kg PMC on CompactPCI Specification PICMG 2 3 R1 0 Utilizes Type B right angle f
Download Pdf Manuals
Related Search