Pressure Fit System
Contents
1. at the end of the lift strap to the hole of the Pressure Fit trolley Be sure that the carabiner is securely attached to the trolley prior to proceeding with the transfer FAILURE TO COMPLY WITH THIS MAY RESULT IN INJURY TO THE INDIVIDUAL BEING LIFTED AND OR THE CAREGIVER OR DAMAGE TO THE LIFT AND OR THE PRESSURE FIT SYSTEM Proceed to transfer the individual in the manner described in the owners manual for the portable lift and sling When the transfer is completed the lift may be removed from the trolley Pressure Fit System User Guide Rev 11 04 09 Page 18 Track sansa Instructions Step 1 Step 2a Remove the end caps from both posts To Unhook the track assembly lift the track up from one post end Step 2b Squeeze the track and unhook from the other post end Step 2c Store the removed adjustable track in a safe place Pressure Fit System User Guide Rev 11 04 09 Page 19 Supporting Post Disassembly Instructions A Warning to read and follow these instructions carefully may result in serious njury Step 3 Press the red button to release the Step 4 safety lock Press the lever in all the way to release the pressure from the ratchet Step 5 While pressing in the lever push and hold Step 6 l the ratchet While holding the ratchet pull out the lever Pressure Fit System User Guide Rev 11 04 09 Page 20 Supporting Post Disassembly Instructions Step 7a Step 7b2. Push the lever up to engage with magnet Push in and hold the ratchet while pushing the top section of post down Step 7d Bring back the lever to vertical posi Step 7c tion Make sure the bottom pin touches the plastic cover Step 9 Take off top and bottom Foot Store the components in a safe place Step 8 Bring back the level and safety lock to Repeat steps 3 to 9 for the other original position Post disassembly Pressure Fit System User Guide Rev 11 04 09 Page 21 Trouble Shooting Should problems arise with the use of the Pressure Fit System review the following chart Find the fault and complete the recommended solution If the fault is not found and or the solution does not correct the problem contact your local authorized dealer for service immediately 1 Set up the post following Post Assembly instructions Check visually and with master level to ensure the post is aligned straight Note Never unlock the post with the track connected 2 Check the floor with master level for flat ness 3 Visually check the level is fine 4 Dismantle the post following Post Disas 1 Level is not working 2 Floor is not leveled 3 Level is damaged 4 Post was knocked with impact Visually the system is not aligned straight sembly Instructions and set up the Post again following Post assembly instruct tions Note Never unlock the post with the track connected If problem persis
3. Printed Name Company Remarks amp Action Taken Service Type o Periodic Inspection o Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken Service Type o Periodic Inspection o Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken Pressure Fit System User Guide Complete this section after each service repair inspection and or maintenance Photocopy additional pages as required o 6 Month Inspection o Repair o Yearly Inspection o Other Signature o 6 Month Inspection o Repair o Yearly Inspection o Other Signature o 6 Month Inspection o Repair o Yearly Inspection o Other Signature o 6 Month Inspection o Repair o Yearly Inspection o Other Signature o 6 Month Inspection o Repair o Yearly Inspection o Other Signature o 6 Month Inspection o Repair o Yearly Inspection o Other Signature Rev 11 04 09 Page 28 Service Record History Service Type o Periodic Inspection o Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken Service Type o Periodic Inspection o Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken Service Type o Periodic Inspection o Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken Service Type o Periodic Inspection o Monthly Inspection Completed By Printed Name Company Remarks amp Action
4. 42 1 047 MAXIMUM SLOPE OF FLOOR AT SPECIFIED DISTANCE Pressure Fit System User Guide Rev 11 04 09 Page 7 Before you start Check Requirements and Cautions continued Cautions AN Failure to observe cautions listed below could result in serious injury or death Cautions Before installation e The pressure fit system parts should not be loose broken or bend If any part is missing or damaged do not install Contact your local authorized dealer immediately e The Pressure Fit System must be assembled prior to use Should you have any questions during assembly contact your local authorised dealer e Never installed the Bottom foot plate on the top portion of post section or vice versa See section Assembly instructions e Ensure rubber feet are cleaned and dry prior to each use See section General Inspection and mainte nance e Do not install The pressure Fit System to suspended ceiling e Do not install The pressure Fit System on a plaster ceiling e Do not install on a sloped floor greater than 5 degree e Ensure floor area is clear off dirt and debris e Never expose the Pressure Fit directly to water Warranty does not cover any misuse or abuse of the Pres sure Fit system e Any accessories used with the Pressure Fit System including lift and sling s should be checked to ensure that they are in good working order Check for signs of wear or fraying prior to use Report any unusual wear or d
5. L Introduction Before using this equipment and to ensure the safe operation of your Pressure Fit System carefully read this entire manual especially the section on Requirements amp Cautions The Pressure Fit System is designed to be used in conjunction with Waverley Glen Systems Ltd portable lift units accessories and slings Please refer to any user guides supplied with these components and reference them while reviewing this manual Should any questions arise from reviewing this manual contact your local authorised Waverley Glen dealer Failure to comply with warnings in this manual may result in injury to the operator or the individual being lifted transferred Damage to the lift and or related components may occur Be sure that the contents of this manual are completely understood prior to using this piece of equipment Store this manual with the documents included with the lift system and sling s Contents of this manual are subject to change without prior written notice Overview of the Pressure Fit System The Pressure Fit System is a lifting aid used by health care professionals and those providing care in the home to lift position and transfer clients or a disabled family member The Pressure Fit System is part of what is termed overhead lift technology which takes advantage of lifting from above and not from below or the side The Pressure Fit System makes it possible to move mobility impaired individuals with minima
6. Pressure Fit System WAVERLEY GLEN Two Post Version SO Owner s Manual Use and Care Trouble Shooting Warranty Information Table of Contents Pressure Fit System PUNT OCU UNO ists hot eshte sits acai west E es 3 Overview of the Pressure Fit System ecceeeeeeeeeees 3 Placement of the Pressure Fit System cceeeeeeeees 4 Components of Pressure Fit System ccceecesseeeeeeeeees 5 Oot ant oXe C a ial ky einen eee nee en ene Snes ne see eee eee een ee eer eee rere 6 Specifications of the Pressure Fit System ee 6 Requirements and Cautions ccccccccccceeeeeeeeeeeseeeeeseeeeeaees 7 Assembly Assembling the Support Posts cc ecccceeeseeeeeeeeees 10 Mounting the Adjustable Track ec ceecceeeee ees 15 Final Inspection Prior to USC ccccceeeeseeeeeeeeenees 16 Completed Pressure Fit System 17 Mounting the Portable Lift ee 18 Disassembly Track Disassembly Instructions 19 Support Post Disassembly Instructions 20 TOUDI SHOO marronar nana EAG 22 General inspection and maintenance cccccccceeeeeeeeeeeeees 24 Service record NIStOSY nannnnannnennnnennnennnnnrnnennnnnrrnnrrnnrrnnreesnernn 26 Waira NUV eko ERER 30 Pressure Fit System User Guide Rev 11 04 09 Page 2 CAUTION DO NOT ATTEMPT TO USE THIS EQUIPMENT WITHOUT FIRST UNDERSTANDING THE CONTENTS OF THIS MANUA
7. Taken Service Type o Periodic Inspection o Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken Service Type o Periodic Inspection o Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken Pressure Fit System User Guide Complete this section after each service repair inspection and or maintenance Photocopy additional pages as required o 6 Month Inspection o Repair o Yearly Inspection o Other Signature o 6 Month Inspection o Repair o Yearly Inspection o Other Signature o 6 Month Inspection o Repair o Yearly Inspection o Other Signature o 6 Month Inspection o Repair o Yearly Inspection o Other Signature o 6 Month Inspection o Repair o Yearly Inspection o Other Signature o 6 Month Inspection o Repair o Yearly Inspection o Other Signature Rev 11 04 09 Page 29 Warranty This Warranty does not affect or in any way limit your Statutory Rights 1 Subject to the exclusions set out in Clause 2 the conditions set out in Clause 3 and the limitations set out in Clause 4 Waverley Glen Systems Ltd as sole licensed representative of Corven Healthcare Inc guarantees all equipment supplied as new against failure within the period of 1 year from date of purchase by virtue of defects in material or workmanship 2 This guarantee does not apply to failure attributable to normal wear and tear damage by natural forces user neglect or mi
8. a room In this drawing arrange ment a general placement of a bed is shown in relationship to the Pressure Fit System Notice that there is still room for a wheelchair to be placed beside the bed The front view show min and max height and width of the pressure fit system for which it can be set up DO NOT GO OUTSIDE OF THIS RANGE OF PLACEMENT OTHERWISE INJURY MAY OCCUR TO THE OPERATOR OF THE LIFT AND OR THE INDIVIDUAL BEING TRANS FERRED AND OR THE PRESSURE FIT SYSTEM Pressure Fit System User Guide Rev 11 04 09 Page 4 Components of the Pressure Fit System pa E Figure 14 FULLY ASSEMBLED PRESSURE FIT SYSTEM Adjustable pou Track Figure 1B DISASSEMBLED PRESSURE FIT SYSTEM Pressure Fit System User Guide Rev 11 04 09 Page 5 Component List The following components are included with your new Pressure Fit System Description Quantity Bottom Foot Top Foot Adjustable Track Owners Manual Supporting Post Warranty Card Specifications of the Pressure Fit System e High strength lightweight Aluminum e Portable or semi permanent installation e Eliminates the mounting of a connection system in the ceiling e Pressure gauge indicator to help ensure proper installation e Quick attachment with secure fixings e Addresses a number of different bedroom amp bathroom situations e Weight capacity 440 Ibs e Adjustable in length e Built in easy slide trolley e Exerting pressure between Floor a
9. ack If so contact local authorized dealer immediately Clean the track slots with cloth and wipe out the dirt or debris Again try extending the tracks If problem persists contact your local authorized dealer immediately 1 visually make sure tracks and wheels are fine and are free of obstacles 2 Ensure that tracks are cleaned with cloth and free of dirt If problem persists contact local authorized dealer immediately Page 22 The adjustable track is not locking on the Post Pins One or more track connector Bracket s are damaged or broken Track lock pin s is are broken or damaged Do not use the system Contact your local authorized dealer immedi ately Misalignment of adjustable track on the Post Pins for Example track is not sitting straight on the post as sembly Post cannot retract Safety Lock Not working Difficult to insert top and bottom foot into Post assembly Track Connector Bracket are loose Pressure Fit System User Guide Track connector hooks are not sitting right on the post pins Ratchet is not held during disassem bly Lever arm is not engaged with mag net Red button is not pressed in enough Physical damage to safety lock cover Lock latch Spring breaks Top post spacer damaged Bottom post plug damaged Bottom plate foot post damaged or bend Top plate foot post damaged or bend Rivets are broken or loose Rev 11 04 09 Check Mo
10. ack to post pin Extend the track and hook to the other post Note Don t leave the track connector on Note Ensure track connector is sitting the spring pin as shown above properly on the spring pin as shown above Step 14a Step 14b Attach the track end cap as shown above Install the other end cap Pressure Fit System User Guide Rev 11 04 09 Page 15 Final Inspection Prior to Use Ensure Pressure Gauge is in the Safe Zone Note Green must be visible on both sides Safety Lock and Level must be firmly Engaged in housing End covers are installed properly Pressure Fit System User Guide Rev 11 04 09 Page 16 Completed Pressure Fit System Completed Pressure Fit System with a M 400 lift Pressure Fit System User Guide Rev 11 04 09 Page 17 Mounting the Portable Lift Figure 14 FULLY ASSEMBLED PRESSURE FIT SYSTEM Prior to mounting the portable lift onto the trolley of the Pressure Fit System please read the owners manual of the portable lift Be sure that the instructions on the use of the lift and any accessories such as slings are thoroughly understood before attempting to use them with the Pressure Fit System FAILURE TO COMPLY WITH THIS MAY RESULT IN INJURY TO THE INDIVIDUAL BEING LIFTED AND OR THE CAREGIVER OR DAMAGE TO THE LIFT AND OR THE PRESSURE FIT SYSTEM Following the instructions for the portable lift attach the carabiner or other similar attaching device located
11. amage immediately to your local authorised dealer e Ensure that a clear space 1s maintained around the Pressure Fit System Remove all furniture and other obstacles out of the way before performing a transfer Pressure Fit System User Guide Rev 11 04 09 Page 8 7 hie you start Check Requirements and Cautions continued Cautions After Installation e Ensure that the pressure gauge is in the safe zone during set up e Ensure Posts are level both visually and with the built in level If unsure use a master level to verify the straightness of the Posts e Make sure track is sitting properly on the posts e Make sure trolley is sliding smoothly on the track e Make sure safety lock button and level are locked e Never unlock the Post when Track is attached e Do not under any circumstance exceed the maximum load rating for this piece of equipment Refer to the Specifications section of this manual e The installation of the Pressure Fit System lift accessories and sling are certified to a maximum load Do not exceed the maximum rated load of any of the components e The Pressure Fit System has been designed to lift vertically at its maximum load and at its maximum height Do not attempt to lift an individual at an angle to the track e The Pressure Fit System and associated lift and sling s are intended only for lifting and transferring of a person Waverley Glen will not be responsible for any damage caused by the
12. chet while pulling out the lever Step 6 Push the top section of post up towards the ceiling with Top foot Upon contact with the ceiling con tinue pushing up until you hear one or two more clicks Note At this point the post should be exerting pressure between the floor and ceiling Step 7 Swing open post level Please ensure the level is fully open Pressure Fit System User Guide Rev 11 04 09 Page 12 Assembly Step 8a Step 8b Grasp bottom section of post lift slightly and Bubble centered adjust until bubble is centered and post is perpendicular to floor and ceiling Step Ya Step 9b Pull the lever down until it clicks Press the lever in to secure it into place Note Lever must rest in vertical position Pressure Fit System User Guide Rev 11 04 09 Page 13 Assembly Assembling the Support Posts Continued SAFE TABLE PRESS E gt foc bbe Step 10 Ensure Pressure Gauge is in the Safe Zone Step lla Swing back the safety lock and level Note Green must be visible on both sides to the original position Step 12 Install the second post repeating steps 1 though 11 Note The distance between the two posts should be 7 to 10 feet Step 1 1b Safety Lock and Level must be firmly Engaged in housing Pressure Fit System User Guide Rev 11 04 09 Page 14 Mounting the Adjustable Track Se OES Step 13a Step 13b Hook one end of the tr
13. ection o Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken Service Type o Periodic Inspection o Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken Service Type o Periodic Inspection o Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken Pressure Fit System User Guide Complete this section after each service repair inspection and or maintenance Photocopy additional pages as required o 6 Month Inspection o Repair o Yearly Inspection o Other Signature o 6 Month Inspection o Repair o Yearly Inspection o Other Signature o 6 Month Inspection o Repair o Yearly Inspection o Other Signature o 6 Month Inspection o Repair o Yearly Inspection o Other Signature o 6 Month Inspection o Repair o Yearly Inspection o Other Signature o 6 Month Inspection o Repair o Yearly Inspection o Other Signature Rev 11 04 09 Page 27 Service Record History Service Type o Periodic Inspection o Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken Service Type o Periodic Inspection o Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken Service Type o Periodic Inspection o Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken Service Type o Periodic Inspection o Monthly Inspection Completed By
14. g Make sure the rubber feet are clean and dry with no residue of dirt or dust left on them Also ensure Floor area is cleaned and free of dirt amp debris Pressure Fit System User Guide Rev 11 04 09 Page 25 Service Record History Initial Information Complete the following section Purchase and Service Information as soon as this equipment is installed Use the service record history to record any completed service and repairs Ensure that the service record is signed and dated each time it is used Be sure to have this piece of equipment serviced on a regular basis as described in the General Inspection and Maintenance Section PURCHASE INFORMATION Product Name Pressure Fit System Serial Date of Purchase Date Installed Purchased From Address City Post Code Telephone No Comments SERVICE INFORMATION Contact the following company for service Company Address City Post Code Telephone No Comments Pressure Fit System User Guide Rev 11 04 09 Page 26 Service Record History Service Type o Periodic Inspection o Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken Service Type o Periodic Inspection o Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken Service Type o Periodic Inspection o Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken Service Type o Periodic Insp
15. intenance A Each Use To be completed by User Prior to each use the Pressure Fit System and associated lift accessories and sling s must be visually in spected Refer to the lift accessory and sling user guides for specific details regarding their inspection Should any of the these items below fail the inspection do not use the Pressure Fit System Contact your local authorised dealer for service Visually check for the following The pressure fit system parts should not be loose broken or bend Ensure ceiling area is rigid and without cracks dust grease and any slippery substance The Bases are on a stable level surface and the Side Support Assemblies are secure The Trolley moves easily along the track The Top and Bottom Foot must be cleaned with wet cloth before installation in order to remove dirt on rubber moulds see cleaning rubber feet The Adjustment Track is placed in the correct location for transferring The portable lift has been inspected as outlined in it s owners manual The sling s has been inspected as outlined in it s owners manual B Cleaning Rubber Feet Instructions Prior to each use the Top and Bottom rubber feet need to cleaned with wet cloth soaked with water Step 1 Take the Bottom rubber foot and wipe off the dirt with a wet cloth as shown in picture Step 2 Take the Top rubber foot and wipe off the dirt with wet cloth as shown in the picture Note After cleanin
16. l strain or risk to the caregiver while providing complete safety dignity and comfort for the client or family member The Pressure Fit System is designed to work with a Waverley Glen portable lift system such as the P 440 Use of other portable lift units with this system may be possible However please contact your local authorised Waverley Glen Systems Ltd dealers in order to obtain approval before use The Pressure Fit System can be used to lift and transfer individuals from a bed chair or similar fixture The length is adjustable and thus can be assembled to suit a wide range of applications The Pressure Fit System is easy to assemble and can be completed by just one person in a short period of time Additionally no tools are required It is also light in weight and once dismantled can be moved to another location such as a hotel or cot tage Please review the following pages that outline the parts included with your package Should you have any questions about this product or its use contact your local authorized dealer Pressure Fit System User Guide Rev 11 04 09 Page 3 Placement of the Pressure Fit System in a Room 7 FEET MIN 10 FEET MAX WIDE DT i TAPPARAN MEE A E i pa Adjustable Track alia af es Se ae TIES WE TE el a a Pd Md Side Support Assembly 7 FEET MIN 9 FEET MAX HEIGHT Transferring Patient from Chair to Bed Drawing showing Front View of the pressure fit system set up in
17. misuse neglect or purposeful destruction of the lift and or its associated components e Under no circumstance should the track lift and sling s or entire system be put in control of a person who has not been properly trained in the use and care of this equipment Failure to adhere to this warning may result in serious injury to the operator and or the individual being lifted transferred e In places where more than one operator will be responsible for using the Pressure Fit associated lift and sling s it is imperative that all operators be trained in its proper use e The Pressure Fit System and associated lift and sling s are not toys Do not use them for unsafe practices Do not allow children to play with the this equipment or any of its components e To maintain optimum function the Pressure Fit should be inspected and maintained on a regular basis See the section titled General Inspection and Maintenance e The manufacturer s warranty is void if persons unauthorized by Waverley Glen perform work on the Pres sure Fit System Pressure Fit System User Guide Rev 11 04 09 Page 9 Assembly A Caution Before using the Pressure Fit System the top plate bottom plate support ing posts and adjustable track must be visually checked to ensure that there are no missing parts or unusual wear and tear Top plate and Bottom plate should be cleaned and dry with wet cloth before installation See Cleaning Rubber Feet Ins
18. nd Ceiling is 80 to 100 Ibs e Specially designed and engineered rubber molded feet for ultimate grip e Leveling indicators on posts e One 1 year warranty Minimum Maximum Dimensions Model Table for the Pressure System Description 7 to 9 feet 341500 Pressure Fit System Two Post Version Pressure Fit System User Guide Rev 11 04 09 Page 6 AN Before you start Check Requirements and Cautions Requirements AN Failure to meet the requirements listed below could result in serious injury or death CEILING REQUIREMENTS e Install the Pressure fit system to a rigid ceiling structure e Ceiling structure must have joists that are spanned maximum up to 24 between the trusses e Ceiling made of wood must be at least 12 7mm 1 2 thickness e Ensure the ceiling structure is not suspended by wires or rods e Ensure ceiling should be clear of any cracks grease water or any other slippery substance Joist framework Above ceiling Ceiling Thickness Min 1 2 Joist Span should be max 24 FLOOR REQUIREMENTS e Ensure Floor area is cleaned and free of dirt amp debris e Floor should meet the requirements of building code standards e Floor must not have a slope of more than 5 degree See table below to determine the slope of floor FLOOR FLOOR ONE END X OTHER END o Y SLOPE OF FLOOR X 6 FEET 7 FEET 8 FEET 9 FEET 10 FEET DISTANCE BETWEEN FLOOR ENDS Y 630 5133 837 9
19. re fit system e Ensure all the components are in working condition and not damaged e Ensure service record history forms are included in the package to record any completed service and re pairs e Complete the Purchase and Service Information as soon as this equipment 1s installed Periodic maintenance e Ensure all the components of Pressure Fit System are in working condition If damaged please contact the dealer for replacement before use e Inspect all the joints and components for wear and fatigue If the parts are damaged then contact dealer for replacement of parts e Clean the rubber feet according to Cleaning Rubber Feet Instructions e Check rubber feet for damages If damage is noticed please contact dealer for replacement e Check the Track and trolley for dirt and debris It should be cleaned with cloth during every use e Ensure the labels are legible and in good condition If not contact dealer for replacement e Record the service record history form for any completed service and repairs e Ensure that the service record is signed and dated each time it is used Follow the general inspection and maintenance instructions for portable lift as mentioned in it s manual FAILURE TO COMPLY WITH THIS MAY RESULT IN INJURY TO THE INDIVIDUAL BEING LIFTED AND OR THE CAREGIVER OR DAMAGE TO THE LIFT AND OR THE PRESSURE FIT SYSTEM Pressure Fit System User Guide Rev 11 04 09 Page 24 General Inspection and Ma
20. suse or to deliberate destruction or to batteries more than 90 days after original purchase 3 This guarantee shall be void if the equipment is not serviced by Waverley Glen Systems Ltd or its authorised service agents in accordance with the manufacturer s recommendations or if any unauthorised person carries out works on the equipment 4 The liability of Waverley Glen Systems Ltd under the terms of this guarantee shall be limited to the replacement of defective parts and in no event shall Waverley Glen Systems Ltd incur liability for any consequential or unforeseeable losses If you have any questions about the manufacture or operation of this equipment please contact Waverley Glen Systems Ltd or your local authorised dealer A PRISM MEDICAL COMPANY WAVERLEY GLEN ee Waverley Glen Systems Ltd 87 Sharer Road Vaughan ON L4L 8Z3 Canada Telephone 905 850 0093 Fax 905 850 8377 Toll Free 1 800 265 0677 This document conforms to EN ISO 10535 requirements CE E amp O E T Trade mark of Corven Health Care Inc Used under licence Printed in Canada Pressure Fit System User Guide Rev 11 04 09 Page 30
21. tructions Should anything look unusual contact your local dealer prior to use Failure to comply with this caution could result in serious injury to the operator the in dividual being lifted and or damage to the Pressure Fit and or portable lift unit Assemkiing the Support Posts Step 2 Tilt the supporting post to the side to facilitate the installation of the top foot Insert the top plate through the top opening of the supporting post Placed the bottom foot on the floor Insert the bottom plate through the opening located at the bottom of the supporting post NOTE Never install Bottom Foot at the Top section of Post NOTE Never install Top Foot at the Bottom section of Post Pressure Fit System User Guide Rev 11 04 09 Page 10 Assembly Assembling the Support Posts Continued Step 3a Step 3b Press the red button down to release Safety Lock Released the safety lock Note Pushing down the Post may help in pulling out the lever Step 4b While pushing with two hands the lever will move out as shown in picture Note This will help in pulling out the lever Step 4a Grab and Push down on the top section of post with two hands as shown in Picture Pressure Fit System User Guide Rev 11 04 09 Page 11 Assembly Assembling the Support Posts Continued Step Sb Push the lever up to engage with the magnet Step Sa Press in and hold the Rat
22. ts contact your local authorized dealer immediately Feet are slipping after installation Feet are not cleaned 1 Clean the feet as per Cleaning Rubber Feet Floor is not cleaned Instructions 2 Ensure floor area is dry and free of debris Lever is not engaged with magnet Pressure gauge is not in safe zone The Adjustable Track does not ex tend smoothly or doesn t extend up to required limit Trolley does not move smoothly along the adjustable track Pressure Fit System User Guide Post Assembly instructions not fol lowed Clutch bearing function fails Lever not cleaned Post assembly instructions not fol lowed Barrel nut is loose or not secured tightly Top plate Spring broken or bend Physical damage to track Track slots are not cleaned Physical damage to track or trolley wheels Track slots or trolley wheels are not cleaned Rev 11 04 09 If problem persists contact your local authorized dealer immediately 1 Press in the Ratchet and hold it Grab the lever and push up to the magnet label Contact local authorized dealer immediately Ensure lever is cleaned and free of grease or dirt If problem persists contact your local authorized dealer immediately 1 2 3 1 2 Set up the post following post assembly In structions Tight the barrel nut with Flat Screw Driver Contact local authorized dealer immediately Check for physical damage to tr
23. unting adjustable Track Assem bly instructions in the user s manual Check visually to ensure track connector hooks are sitting at the same height If problem persists contact local authorized dealer immediately Follow Post Disassembly instructions to dismantle the post Follow Post Disassembly instructions to dismantle the post Press in the Red button all the way so that safety lock can be engaged Contact local authorized dealer immediately Contact local authorized dealer immedi ately Contact local authorized dealer immediately to continue the proper functioning of Pressure Fit System Do not use the system Contact your local authorized dealer immedi ately Page 23 General Inspection and Maintenance A Failure to follow inspection and maintenance instructions below as instructed may result in serious injury or death Periodic general inspection and maintenance should be performed by a person who is properly qualified and trained with the use and care of The Pressure Fit System Any defects and damage to the Pressure Fit System that have lead to corrective actions should be noted and dated by the inspector The defects and corrective actions report should be submitted in written form to the dealer Upon Receipt of The pressure Fit system e Ensure all the received components are according to the component list e Ensure the user manual is present other wise do not install the pressu
Download Pdf Manuals
Related Search