EXZ4U_3_na
Contents
1. DDD IMPORTANT 44d e Resizing an image creates a new file that contains the image in the size you select The file with the original image also remains in memory e Images smaller than 640 x 480 pixels cannot be resized e An image recorded using the 2304 x 1536 3 2 pixel size cannot be resized e Note that you can resize snapshots recorded with this camera only e If the message This function is not supported for this file appears it means that the current image cannot be resized e The resize operation cannot be performed if there is not enough memory to store the resized image 89 PLAYBACK Cropping an Image Use the following procedure when you want to crop a portion of an enlarged image and use the remaining part of the image as an e mail attachment Web page image etc 1 In the PLAY mode use lt 4 and gt to scroll through images and display the one you want to crop 2 Press MENU 3 Select the PLAY tab select Trimming and then press gt e This causes a cropping boundary to appear 4 Use the zoom button 13 Q to make the cropping boundary larger or smaller e The size of the cropping boundary depends on the size of the image on the display 5 Use A V 4 and gt to move the cropping boundary up down left or right until the area of the image you want to extract is within the boundary Press SET to extract the part of the image en2. Press MENU Select the PLAY tab select Dubbing and then press P Press the shutter release button to start audio recording Recording stops after about 30 seconds or when you press the shutter release button PLAYBACK To re record audio 1 In the PLAY mode use lt and gt to scroll through snapshots until the one whose audio you want to re record is displayed Select the PLAY tab select Dubbing and then press gt Use A and V to select Delete and then press SET e If you merely want to delete the audio with re recording press MENU here to complete the procedure Press the shutter release button to start audio recording Recording stops after about 30 seconds or when you press the shutter release button e This deletes the previous recording and replaces it with a new one DDD IMPORTANT 444 e Keep the microphone on the front of the OQ o camera pointed at the f subject e Take care that you do not block the microphone with your fingers Microphone e Good recording results are not possible when the camera is too far from the subject e Operating camera buttons during recording can cause button noise to be included in the audio e The Audio icon appears on the monitor screen after audio recording is complete e You will not be able to record audio when remaining memory capacity is low e The following types of audio
3. following operations while audio is playing To do this Do this Fast forward or fast reverse Hold down 4 or gt the audio Pause and unpause audio Press SET playback Adjust audio volume Press A or V Cancel playback Press MENU PLAYBACK Flipping the Display 71 In the PLAY mode use lt and gt to scroll through images on the monitor screen and display the one you want The following procedure flips the image 180 degrees This comes in handy when you want to show someone standing in front of you an image on the monitor screen 2 Press the shutter release button and SET at SET the same time e This flips the image 180 degrees The histogram or any other display information you had displayed is cleared automatically whenever you flip the image e While an image is flipped you can use lt 4 and gt to scroll to another image if you want 3 To return the image to its normal orientation press any button other than A V lt or gt DDD IMPORTANT 4 e Note that you cannot play an audio snapshot or a voice recording file on the monitor screen while a flipped image is displayed e You cannot use the above procedure to flip an image while a zoomed image 9 image screen calendar screen image an audio snapshot or a voice recording file image is on the display PLAYBACK Zooming the Display Image 3 Use A V lt
4. 4 held down until images appear on the monitor screen e This starts the Image Roulette operation scrolling images on the display finally stopping at one Press lt or gt to restart the Image Roulette operation To turn off Image Roulette align the mode selector with REC to enter the REC mode or press the power button to turn off the camera IMPORTANT 4 e Image Roulette does not display voice recording images e Image Roulette is disabled when there is only one snapshot image available e Note that Image Roulette works only with images recorded with this camera Image Roulette may not operate properly when other types of images are in memory e If you do not start another Image Roulette operation for about one minute after the final image appears the camera enters its normal PLAY mode PLAYBACK Adding Audio to a Snapshot The after recording feature lets you add audio to snapshots after they are recorded You can also re record an audio image one with a icon on it e Audio Format WAVE ADPCM recording format This is the Windows standard format for audio recording The file extension of a WAVE ADPCM file is WAV e Recording Time Up to about 30 seconds per image e Audio File Size Approximately 120KB 30 second recording of approximately 4KB per second In the PLAY mode use lt and gt to scroll through snapshots until the one to which you want to add audio is displayed
5. the camera is on its USB cradle You can play a Photo Stand slideshow without worrying about remaining battery power or you can specify display of a particular image Photo Stand feature operations are performed in accordance with slideshow setting See page 93 for information about configuring slideshow settings to suit your needs 1 Set the camera onto the USB cradle e Do not place the camera onto the USB cradle while it is turned on 2 Press the USB cradle s PHOTO button e This starts the Photo Stand slideshow with the images or image you specified under To specify the slideshow images page 95 PHOTO e Pressing MENU displays a screen for configuring slideshow settings To restart the slideshow press MENU while the menu screen is displayed or select Start and then press SET e While audio is playing you can use A and V to adjust the volume level 3 To stop the Phot Stand slideshow press PHOTO again DDD IMPORTANT 444 e The battery is not charged while a Photo Stand slideshow is in progress To charge the battery stop the slideshow PLAYBACK Rotating the Display Image Use the following procedure to rotate the image 90 degrees and register the rotation information along with the image After you do this the image is always displayed in its rotated orientation whenever it appears during a slideshow page 93 or on your computer screen Note that the image is rotated auto
6. 4 and gt to shift the image up down left or right Perform the following procedure to zoom the image currently on the monitor screen up to four times its normal 4 Press MENU to return the image to its size original size 1 In the PLAY mode use lt 4 and gt to display DDD IMPORTANT 44d the image you want Depending on the original size of the recorded image you may not be able to zoom a display image 2 Press the zoom the full four times its normal size button Q to enlarge the image e This displays an indicator that shows the current zoom factor e You can toggle between the zoomed image and Current zoom factor normal image by pressing MENU PLAYBACK Resizing an Image You can use the following procedure to change a snapshot image to either SXGA size 1280 x 960 pixels or VGA size 640 x 480 pixels e VGA is the optimum image size for attachment to e mail messages or incorporation into Web pages 1 In the PLAY mode press MENU 2 Select the PLAY tab select Resize and then press gt x 280x91 1640x480 Cancel 3 Use lt 4 and gt to scroll through images and display the one you want to resize 4 Use A and V to select the setting you want and then press SET To do this Select this Resize to 1280 x 960 pixels SXGA 1280 x 960 Resize to 640 x 480 pixels VGA 640 x 480 Cancel the resizing operation Cancel
7. PLAYBACK You can use the camera s built in monitor screen to view 3 Use gt forward or lt back to scroll images after you record them through files on the monitor screen Basic Playback Operation Use the following procedure to scroll through files stored in the camera s memory DDD NOTES 44a 1 Press the power Power button e Holding down lt 4 or gt scrolls images at high button to turn on the speed e In order to allow for faster playback image scrolling the image that initially appears on the monitor screen is a preview image which is of somewhat lower quality than the actual display image The actual display image appears a short while after the preview image This does not apply to images copied from another digital camera camera e This causes an image or a message to appear on the monitor screen 2 Align the mode Mode selector selector with PLAY e This enters the PLAY J mode PLAY REC gt Cr MENU WQ a PLAYBACK Playing an Audio Snapshot b gt IMPORTANT 444 e Audio volume can be adjusted only when playback is being performed or is paused Perform the steps below to display an audio snapshot indicated by a indicator and play its audio 1 In the PLAY mode use lt 4 and gt until the image you want is displayed 2 Press SET 100 0023 e This plays back the audio that accompanies the displayed image e You can perform the
8. closed in the cropping boundary e If you want to cancel the procedure at any point press MENU IMPORTANT 444 e Cropping an image creates a new file that contains the cropped image The file with the original image also remains in memory e An image recorded using the 2304 x 1536 3 2 pixel size cannot be cropped e Voice recording file images cannot be cropped e An image recorded using another camera model cannot be cropped e If the message This function is not supported for this file appears it means that the current image cannot be cropped e The cropping operation cannot be performed if there is not enough memory to store the cropped image PLAYBACK Displaying the 9 image View The following procedure displays nine images on the monitor screen at the same time 1 In the PLAY mode press the zoom button e This displays the 9 image screen with the image that was on the monitor screen in step 2 in the center with a selection boundary around it e Pressing the zoom button Ei twice displays the calendar screen e is displayed in the calendar screen to indicate voice recording file images page 76 e When there are nine or fewer images they are displayed in order with Image 1 in the upper left corner with the selection boundary around it Use A V lt 4 and gt to move the selection boundary to the image you want Pressing gt while the selection boundary is in the rig
9. ht column or lt 4 while it is in the left column scrolls to the next full screen of nine images Example When there are 20 images in memory and Image 1 is displayed first 3 Pressing any button besides A V lt or gt displays the full size version of the image where the selection boundary is located PLAYBACK Selecting a Specific Image in the 9 image View 1 Display the 9 image view 2 Use A V lt 4 and gt to move the selection boundary up down left or right until it is located at the image you want to view 3 Pressing any button besides A V lt 4 or gt displays the selected image e This displays the full size version of the image you selected Selection boundary Displaying the Calendar Screen Use the following procedure to display a 1 month calendar While the calendar is on the display you can select a date which displays the first image recorded on that date This helps to make it easy to find the images you want 1 In the PLAY mode press the zoom button 2 twice e You can also display the calendar screen in the PLAY mode by pressing MENU selecting the PLAY tab selecting Calendar and then pressing gt 2 Use A V lt 4 and gt to move the date selection cursor e Use the procedure under Changing the Date Format on page 125 to specify the date format e The image dis
10. l on page 96 4 Use A and V to select Start and then press SET e This starts the slide show 5 To stop Slide Show press SET The slideshow will also stop automatically after the amount of time you specified for Time elapses IMPORTANT 444 e Note that all buttons are disabled while an image change is in progress Wait until an image is stopped on the monitor screen before performing a button operation or hold down the button until the image stops e When the slideshow comes to an audio snapshot or voice recording file it plays the audio once and then advances to the next file e While audio is playing you can use A and F to adjust the volume level e Images copied from another digital camera or a computer may take longer time to appear than the slideshow interval time you specify PLAYBACK To specify the slideshow images 1 Use A and F to select Images and then press gt 2 Use A and V to select the setting you want and then press SET folder page 147 in the slideshow To do this Select this setting Include all files in file memory in the Alli slideshow mages Display a single file One Image Include all files in the FAVORITE Favorites 3 Use A and V to select Start and then press SET e This starts the slideshow e The audio of audio snapshot and voice recording files is also played back E Selecti
11. matically during a slideshow only Rotating an image ensures that images you recorded with the camera held sideways appear correctly during a slideshow 1 In the PLAY mode press MENU 2 Select the PLAY tab select Rotation and then press P 3 Use lt 4 and gt to scroll through images until the one you want to rotate is on the monitor screen 4 Use A and V to select Rotate and then press SET e This rotates the image 90 degrees to the right Cancel 5 After you are finished configuring settings press the MENU button to exit the setting screen DDD IMPORTANT 44d e You cannot rotate an image that is protected To rotate such an image first unprotect it e You may not be able to rotate a digital image that was recorded with another type of digital camera e You cannot rotate voice record images PLAYBACK Using Image Roulette Image Roulette cycles images like a slot machine on the display before stopping at one of them When you start an Image Roulette operation images scroll randomly on the screen At first images scroll at high speed Then the scrolling gradually slows down until a single image is stopped on the screen The image that finally appears is random and subject to no rules or system 1 2 Align the mode selector with PLAY While the camera is turned off hold down lt 4 as you press the power button to turn it on e Keep lt
12. ng a Particular Image for a Slideshow When you select One image as the slideshow type the slide show displays only one image without changing it Use this setting when you want a particular image to remain on the display while the camera is on the USB cradle Photo Stand feature 1 Select One image and then press gt 2 Use lt and gt to scroll through the images until the one you want to use is on the monitor screen 3 Press SET to register your selection and return to the menu screen e Pressing MENU instead of SET returns to the menu screen without registering the setting PLAYBACK To specify the slideshow time 1 Use A and V to select Time 2 Use lt and gt to specify the time setting you want and then press SET e You can specify a time in the range of 1 to 60 minutes 3 Use A and V to select Start and then press SET e This starts the slideshow To set the slideshow interval 1 Use A and V to select Interval 2 Use lt and gt to specify the interval setting you want and then press SET e You can specify MAX or a value in the range of 1 to 30 seconds as the interval 3 Use A and V to select Start and then press SET e This starts the slideshow PLAYBACK Using the Photo Stand Feature The Photo Stand feature lets you specify what should appear on the camera s monitor screen while
13. played on the calendar for each date is the first image that was recorded on that date Mon Tue Wed Thu Fri Sat ee Month Year Date selection cursor oo PLAYBACK e Pressing A while the date selection cursor is Endure a Slide Show located anywhere in the top line of the calendar causes the previous month to appear Slide Show automatically plays back images in sequence Pressing V while the date selection cursor is at a fixed interval located anywhere in the bottom line of the calendar causes the next month to appear e To exit the calendar screen press MENU or the Q zoom button is displayed in the calendar screen to indicate voice recording file images page 76 1 In the PLAY mode press MENU e appears in place of the image when the date contains data that cannot be displayed by this 2 Select the PLAY tab select Slideshow camera and then press gt 3 To view the large version of a date s image move the date selection cursor to the date and then press SET e This displays the first image that was recorded on the selected date PLAYBACK 3 Configure the slideshow settings e See the pages indicated below for more information For information about configuring this setting Go here To specify the slideshow Images images on page 95 r To specify the slideshow Time time on page 96 To set the slideshow Interval interva
14. recording are not supported Adding audio to a protected snapshot page 106 e Audio that is re recorded or deleted cannot be recovered Make sure you no longer need audio before re recording or deleting it PLAYBACK Playing Back a Voice Recording File DDD IMPORTANT 444 Perform the following steps to play back a voice recording ae nc ae only when playback is me e If your recording has index marks page 77 inside it you can jump to the index mark before or after the 1 In the PLAY mode use lt 4 and gt to display current playback location by pausing playback and the voice file a file with QJ on it you want to then pressing lt 4 or gt Next press SET to play resume playback from the index mark position 2 Press SET e This starts playback of the voice recording file through the camera s speaker e You can perform the following operations while audio is playing 00 02 00 To do this Do this Fast forward or fast reverse the audio Hold down lt 1 or gt Pause and unpause audio playback Press SET Adjust audio volume Press A or V Cancel playback Press MENU EE O
Download Pdf Manuals
Related Search
EXZ4U_3_na