fre-102ar instructions
Contents
1. LED sufficient charge to operate Even though the Green light is ON we still recommend a full 8 hour charge The FRE 102AR can be operated with the charger connected to the mains supply if required On receipt of your new laser we suggest charging the batteries fully for 7 8 hours A Spare Battery holder is included in the kit amp used as a back up power source Four type C 1 5V Alkaline batteries can be used instead or in an emergency but do NOT attempt to recharge them otherwise serious damage will occur Positioning the Laser Mount the FRE 102AR on a generally level firm surface or 5 8 threaded Tripod To operate correctly this surface must be within 5 deg of true horizontal The laser can be used Indoors or Outdoors where it is waterproof to IP55 Controls Power ON OFF is via the red button The laser takes approx 15 to 25 seconds to auto level then the prism head rotates amp projects a visible red laser beam The rotational speed is variable in 4 increments Adjust head speed using the top right hand button amp when pressed it stops the red dot then increases the head s rotational speed in 4 steps up to a maximum speed of 1 000rpm For Interior work we suggest using slower speeds where the laser beam is easier to see by eye but for Exterior Groundworks run the FRE 102AR at its maximum speed of 1 000rpm which gives the best working range when used with the supplied Laser Detector Even with its brigh2. FRE 102AR INSTRUCTIONS from LASER LEVELS ONLINE www laser level co uk Tel 01246 269777 Thank you for purchasing the Fukuda FRE 102AR RED beam rotary laser kit These instructions are intended to explain the quick basics to operating this equipment Please read them carefully If you need any more help advice or the instrument requires calibration or repair then please contact our Service Dept on tel 01246 269 777 or fax 01246 260 007 We would be pleased to help Power source The FRE 102AR has a special battery pack located in the front base of the laser To change unscrew the silver lock slide out to remove amp carefully refit It contains 4pc x sealed for life Ni MH type C 4000mAh 1 2V cells Please note that this battery pack can be charged either in or outside of the laser The Mains Charger supplied will charge these batteries in around 7 8 hours to give up to 30 hrs of continuous use It takes 4 to 5 charge discharge cycles for this battery pack to reach its maximum capacity Spare batteries are available Mains Charger The general procedure to adopt is to use the laser during the working day amp charge up overnight You cannot damage the system by over charging the batteries When plugged into a 230V mains supply the red LED flashes every 1 sec Connect to the rubber protected socket located on the front of the battery pack then the Charger s LED should be ON continuously ie Red LED charging Green
3. o please take extra care SAFETY PRECAUTIONS Comply with class 2 laser operating safety procedures See main Manual Display a Laser Safety Notice in the work area General Advice This is an accurate measuring device so to give good service look after it Prevent the FRE 102AR from receiving severe knocks bangs or vibration Store the laser amp its accessories in the supplied carry case If wet dry before storing amp keep in storage temperatures within 5 30 deg C Remove all batteries before long term storage to prevent internal damage Key Specifications Laser accuracy 2 25mm 30m Operating range 20m visible or 600m diameter with the supplied detector IR Remote control range 20m for full details see main Manufacturer s User Manual There are NO User Serviceable Parts This would void the warranty We offer a full Back up service including repairs calibration amp usage advice Accessories for the various Trades are also available on request eg Tripods staffs poles kits amp wall brackets etc Please contact us Laser Levels Online Unit 35 Bridge Business Centre Beresford Way CHESTERFIELD S41 9FG England Tel 01246 269777 Fax 01246 260007 sales laser level co uk www laser level co uk Laser Levels Online is an internet trading division of P R Engineering Ltd kkkkkkkkkkkkkkkkk
4. or amp Remote Control The remote control is pictured on the right Remote Control Fit the supplied 2pc x AA alkaline batteries taking care with correct polarity The Remote s keypad can set the following functions 1 Rotating speed in increments slow for Indoors fast max for Outdoors 2 Scan angles in increments 3 Scan line position around the room 4 Auto Manual grade settings via top button auto man 5 Two ARROW buttons to set the required X Y grades TIP it is often better to use the Remote Control rather than the instrument s keypad because then you do not disturb the laser s sensitive mechanism FRD400 Detector Fit the supplied 9V battery polarity marked Power up via ON OFF button The middle button switches the sounder s volume ON loud quiet or OFF The right hand button sets sensitivity coarse 2mm or fine 1mm of the red pick up window A rear LCD repeats the main front display Note the case markings amp setting notches You can use the detector with or without its staff mounting bracket Detector Procedure face towards rotating laser to find the rotating laser beam via the red pick up window If the sun is low in the sky amp shining into the red window shield it with a cupped hand to prevent false readings Positioning the FRE 102AR itself in full sun is no problem but the detector window can in some instances be affected by direct bright sunlight or reflections S
5. s can be found on the Remote Control To return to Auto level switch the Manual button to OFF both LEDs turn off The Laser will wait to find true level then automatically restart self levelled Setting Y axis slope This sets a grade in the Y axis Procedure switch ON the FRE 102AR then auto levels Press the Manual button twice on laser s keypad bottom left hand side amp the green Y LED illuminates Using the up amp down Arrow buttons set the slope fall required aS measured on your staff Again the same buttons can be found on the Remote Control To return to Auto level switch the Manual button to OFF both LEDs turn off The Laser will pause whilst it finds true level then automatically restart self levelled Setting both X amp Y axis slope dual grade Proceed as above but set BOTH X and Y axis as required Automatic Drift System ADS Operated via bottom right hand button marked tilt Once the FRE 102AR is ON and rotating in the auto self levelled mode the automatic drift system can be activated Press the button amp the green LED will illuminate ADS is now ON If the Laser is knocked or caught by a gust of wind for example the laser head will stop rotating and the green ADS LED will flash quickly in alarm condition Check all is OK press the tilt button again amp the laser will reset to AUTO level IMPORTANT NOTE The ADS function cannot be set when Grading Laser Detect
6. t red beam the detector will still be required for most outdoor work SCAN function for Interior setting out The top button on the left of the keypad is the Scan function The User can set a static dot 10 45 90 180 degree lines as required amp use the two buttons beneath marked with rotational arrows to move these lines around the room AS THIS LASER AUTO LEVELS BOTH HORIZONTALLY amp VERTICALLY all the control settings above operate in either mode Vertical leveling with the laser positioned on its side is often refered to as Laydown where the User can project vertical laser lines or for setting out Site SQUARING 90 deg Grading This is a DUAL GRADE facility laser level This means that the FRE 102AR can be switched to Manual to over ride the level sensors via the auto man button and then the User can set a grade incline slope in the X axis only Y axis only or both together The max settable slope is an approx fall of 1m over 10m For X amp Y alignment please see the case markings on the TOP of the laser body where an arrow points in the direction of the axis being set Setting a single axis slope This sets a grade in the X axis Procedure switch ON the FRE 102AR then auto levels Press the auto man button on laser s keypad bottom left hand side amp the green X LED illuminates Using the up amp down Arrow buttons set the slope fall required as measured on your staff The same button
Download Pdf Manuals
Related Search