AZ-20A Ice Maker
Contents
1. Condenser Compressor Fan motor Normal Sounds Your new ice maker may make sounds that are unfamiliar to you Most of the new sounds are normal Hard surfaces like the floor and walls can amplify the sounds The following describes the kinds of sounds that might be new to you and what may be causing them Rattling noises may come from the flow of the refrigerant or the water line Items stored on top of the ice maker can also make noises The high efficiency compressor may make a pulsating or high pitched sound Running water may make a splashing sound You may hear air being forced over the condenser by the condenser fan During the harvest cycle you may hear the sound of ice cubes falling into the ice storage bin Preparing the Ice Maker for Long Storage If the ice maker will not be used for a long time or is to be moved to another place it will be necessary to drain the system of water S A E D Shut off the water supply at the main water source Disconnect the water supply line from the water inlet Shut off the electric supply at main electrical power source Take out the ice storage bin to remove remaining ice and water Dry it Connect the drain hose to drain out water completely then plug up the drain outlet after finishing Pull off the drainage tube of the water trough to drain off all water 7 Le2. Condenser may be dirty Clean the condenser from the unit storage bin Water supply connection leaking 25 The air flow to the ice maker Check the installation Machine makes ice _ may be obstructed but ice storage bin The ambient temperature and does not fill up with i ice water temperature are high Check the installation or machine is near some heat source A few water drops fall to the Normal condensation on the door or floor when you open the some water together with ice Take Water is leaking door to take out ice from care when you take out ice Tighten fitting See Connecting the Water Line Problem Possible Cause Probable Correction Cubes are partially formed or are white Not enough water in the Check if the water supply pressure is below 15 psig Check water supply filter may be water trough restricted at the bottom Check for a water leak at the water trough The legs are not leveled and Level and lock the feet See Noise during locked Leveling the Ice Maker operation Certain sounds are normal See Normal Sounds The ice maker stops The electricity is off Reconnect the power supply line The room temperature is out Cut off the electricity let the ice maker stop working until the suddenly while of the stated range temperature returns to within the making i
3. SA JACKSON GRILLS aan y gt e yh TUM WY Automatic Outdoor Ice Maker User s Manual Be sure unit is standing upright 24 hours prior to plug in Model AZ 20A Table of Contents Page ICEMAKER SAFETY iii 2 IMPORTAN T SABEGUARDS aia 3 5 TECHNICAL INFORMATION sirio a 5 INTRODUCCION RS A AE SA AAA 6 COMPONENT LOCATIONS a 7 ICEMARKER INSTALA TT aa 8 15 WACK ivi dei ei 8 Location REQuiremients is A EEDE 8 9 Electrical REquireMmennes rra ai nopal 10 A N l1 Reversing the Door S Wine veracidad innatas dela isaac 11 12 Water SIPPSS EA AA ad A AA AL td 12 13 A A Dal ia ok ines Maca a tuoi cea ee oes 13 MAS Gaal AUN OS Sey rela eRe tag E cau ge wan ta ces bas aos INE owned oases 14 OPERATION iia ic 15 18 Final Checklist before Opera een nas a S 15 Operating Methodi ea i an io 15 16 How the Machine Makes Tee di loo aio pis 16 How the Machine Uses the Water ocio td 17 Nora US NO a oes vende ena a easels 18 Preparing the Ice Maker for Long Storage iii id 18 CLEANING AND MAINTENANCE Ra 19 22 Exterior Cleaning veia dia indias 19 tenor Cle anil o na etal Seal eae eee Siena aades 20 Condenser Ci MIO gis 20 Water Distribution Tube Cleaning A ds 21 Ice Making System Clean iria 21 22 Control BO O AO AA 23 24 MAJOR FUNCTION Si A AOS 24 TROUBLESHOOTING a aise Saas ous a E ae EA aR 25 26 LIMITED WARRANTY sininanatia ii idas 27 We reserve the right to make changes in specifications and design wi
4. Technical Information Model AZ 20A Electrical power 115VAC 60Hz Power consumption 13 2kWh 100 lbs of ice Ice making Ice harvest rated current 3 0A 3 6A Refrigerant R134a 3 88 oz High Low Side Pressure 350psig 130psig Width x Depth x Height with feet 14 6 X 23 6 X 33 5 Unit weight 88 lbs Ice making capacity 44 lbs day Max ice storage 25 lbs Ice shape Cube Ice cube dimensions 34 X X 1 The technical data and performance index listed above should be used for reference only They are subject to change The actual quantity of ice produced per day can vary with room and water conditions Introduction The Jackson Grills AZ 20A Ice Maker produces hard crystal clear gourmet cube ice and offers convenience for homeowners and hotel guests It can be used both indoors and outdoors An insulated removable ice storage bin is included This user s manual is intended as a resource for persons installing using and servicing model AZ 20A It contains valuable information on safety and maintenance Jackson Grills strongly recommends that this manual be kept in a place where it can be accessed when needed Every Jackson Grills Ice Maker is designed and manufactured according to the highest standards of safety and performance It meets or exceeds the safety standard of UL563 Component Locations Water distribution tube Door Evaporator ice mold Ice full probe Water trough Floater Ice s
5. Allow 20 minutes for proper cleaning After cleaning turn the machine OFF at the Power switch Drain off the waste water to a container by means of the drain hose at the front of the water trough NOTE Do not drain off the waste water to the inside of the cabinet 21 10 Repeat steps 3 and 4 without Ice Maker Cleaning Solution 3 times to rinse the ice making system NOTE The use of the Ice Maker Cleaner Solution in the water bin during the rinse is not needed A WARNING The ice machine cleaner contains acids DO NOT use or mix with any other solvent based cleaner products Use rubber gloves to protect hands Carefully read the material safety instructions on the container of the ice machine cleaner DISCARD the first batch of ice produced after cleaning Prepare a sanitizing solution made of 1 ounce of household bleach and 2 gallons of hot water 95 to 115 F Wipe the entire bin inside and outside covering the entire surface of the walls Fill a spray bottle with the sanitizing solution and spray all corners and edges making sure to cover all surfaces with the solution Allow the solution to be in contact for at least 3 minutes then dry Repeat step 5 to rinse the ice making system one more time Set the Power switch to the ON position The machine will return to the regular ice making mode Discard the first batch of ice 22 Control Box rear of unit A Red LED A Tesca Green
6. maker Turn the leveling legs to the left to raise that side of the ice maker IMPORTANT Once you are ready to install it in a cabinet or directly on the floor you must adjust the legs to level the ice maker Reversing the Door Swing TOOLS NEEDED Flat screwdriver Phillips screwdriver IMPORTANT Before you begin unplug the ice maker or disconnect power Top hinge cover cabinet Top hinge mat Ss Top hinge Door 11 To remove door from hinges 1 Remove the top hinge cover 2 Using a Phillips screwdriver remove the screws then remove top hinge mat and top hinge Keep the parts together and set them aside 3 Lift the door off of the bottom hinge and turn it upside down so that the handle is on the right Set the door aside To replace door on hinges 1 Using a flat screwdriver remove the plug buttons from the screw holes opposite the door hinges top and bottom Set aside 2 Remove the bottom hinge and place it on the opposite side at the bottom of the door 3 Position the door on the bottom hinge 4 Align the door on the bottom hinge and replace the top hinge and top hinge mat 5 Replace top hinge cover 6 Push the plug buttons into the original screw holes Water Supply The water supply should be ready at the point of installation The water supply pressure should be a minimum of 15 psig with a static pressure not more than 80 psig A wall outlet directly behind the ice machine will make instal
7. properly You may need to make several adjustments to level it All installations must be in accordance with local plumbing code requirements Make certain that the hoses are not pinched or kinked or damaged during installation Check for leaks after connection Although the unit has been tested at the factory due to long term transit and storage the first batch of cubes must be discarded Remove the packing materials and clean the ice maker before using Turn on the water supply tap before switching on the ice maker Never turn the water supply tap off when the ice maker is working Except to take ice from the unit keep the door closed in order to reduce ice melting and to promote proper ice formation If the ice maker will not be used for a long time before the next use it must be thoroughly cleaned Follow carefully any instructions provided for cleaning or use of sanitizing solution Do not leave any solution inside the ice maker after cleaning DO NOT use solvent based cleaning agents or abrasives on the interior These cleaners may transmit taste to the ice cubes or damage or discolor the interior The ice machine cleaner contains acids DO NOT use or mix with any other solvent based cleaner products Use rubber gloves to protect hand Carefully read the material safety instructions on the container of the ice machine cleaner Do not use this apparatus for other than its intended purpose SAVE THESE INSTRUCTIONS Electrical Con
8. Before operating put all panels back into place Never allow children to operate play with or crawl inside the ice maker Do not touch the evaporator by hand when the machine is operating Unplug the ice maker or disconnect power before cleaning or servicing Failure to do so can result in electrical shock or death Do not attempt to repair or replace any part of your ice maker unless it is specifically recommended in this manual All other servicing should be referred to a qualified technician amp WARNING Use two or more people to move and install ice maker Failure to do so can result in back or other injury Never install or operate the unit in an enclosed area such as a closed cabinet To ensure proper ventilation for your ice maker the front of the unit must be completely unobstructed Choose a well ventilated area with temperatures above 45 F 7 C and below 110 F 43 C The ice maker should not be located next to ovens grills or other sources of high heat The ice maker must be installed with all electrical and water connections in accordance with state and local codes A standard electrical supply 115VAC 60Hz 15A properly grounded in accordance with the National Electrical Code and local codes and ordinances is required Do not kink or pinch the power supply cord between the ice maker and cabinet The fuse or circuit breaker size should be 15 amperes It is important for the ice maker to be leveled in order to work
9. LED A Ice making Yellow LED P Ice harvest Descriptions of LEDs and buttons 1 Red LED Ice Full indicator light When this LED is lit the ice storage bin is full of ice or there is something between the two arms of the ice full sensor in the ice storage bin The unit will stop working When ice cubes are taken out of the ice storage bin clearing the sensor the red LED will keep flashing for 3 minutes Then the unit will restart and return to the ice making mode 2 Green LED Ice Making indicator light When this LED is lit the unit is working in the Ice Making mode controlled by a temperature probe on the evaporator When the green LED is flashing the unit is working in the Ice Making mode controlled by a fixed timer 3 Yellow LED Ice Harvest indicator light When this LED is lit the unit is working in the Ice Harvest mode controlled by a temperature probe on the evaporator When the yellow LED is flashing the unit is working in the Ice Harvest mode controlled by a fixed timer 4 Clean button When this button is pressed the unit enters the Cleaning mode The green and yellow LEDs flash together To stop the Cleaning mode just press the button again 5 Mode button Mainly for service When this button is pressed unit can change from Ice Making mode to Ice Harvest mode or from Ice Harvest mode to Ice Making mode You can judge the mode from the status of the green and yellow LEDs 6 Adjust button Ma
10. ainage feature of earlier models has been modified to simplify the drainage procedure Follow the steps outlined below Connecting the drain line NOTE If there is a drain line near the ice maker or the ice maker will be used as an outdoor unit the best choice is to drain water to the drain line through the drain hose provided with ice maker 1 Locate the floor drain near the ice maker The distance should be less than 5 feet since the length of the long drain hose provided with the ice maker is about 5 feet Find the drain outlet on the back of ice maker then take off the rear drainage plug Connect the nut of the drain outlet to the water draining hose and insert the other side of the hose into the drain line NOTE The drain hose should never be allowed to hang or loop higher than the bottom of the ice storage bin 2 All horizontal runs of drain lines must have a fall of 1 4 per foot An air gap will likely be required between the ice maker drain hose and the drain waste receptacle A stand pipe with a trap below it would be acceptable for the drain waste receptacle A floor drain is also acceptable 3 Pour 1 gallon of water into the ice storage bin to check for leaks at all drain connections and at the nut of the drain water hole Tighten any connections or nuts that leak IMPORTANT This ice maker is not a freezer Infrequent drainage will cause a high rate of melting in the ice storage bin 13 Installation Types This i
11. aker is behind the cabinet plug in the ice maker 6 Push the ice maker into position 7 Seal all around the cabinet to the floor with an approved caulking compound Operation Final Check List before Operation 1 Have all packing materials and tape been removed from the interior and exterior of the ice maker 2 Did you clean the ice storage bin 3 Have the installation instructions been followed including connecting the machine to water and electricity 4 Has the machine been leveled 5 Is the ice maker in a site where the ambient temperature is between 45 F 7 C and 110 F 43 C and the water temperature within 41 F 5 C and 90 F 32 C all year round 6 Has the water supply pressure been checked to ensure a minimum of 15 psig with a static pressure not to exceed 80 psig 7 Is there a clearance of at least 4 at the rear and 1 at the top and sides for proper air circulation 8 Has the power supply voltage been checked or tested against the nameplate rating And has proper grounding been installed for the ice maker 9 Is the ice maker plugged in 10 Have you turned on the main water supply and the tap 11 Have you checked for leaks at all water supply connections Operating Method 1 Turn on the water tap and let the water trough fill Then set the Power switch on the front panel to the ON position The ice maker will start working automatically Ice Ice Ice full making harvesting stag
12. alified personnel To ensure proper ventilation for your ice maker the front of the unit must be completely unobstructed When installing the ice maker under a counter follow the recommended spacing dimensions shown on the previous page Allow 4 102mm or more clearance at rear 1 25 4mm at the top and sides for proper air circulation The installation should allow the ice maker to be pulled forward for servicing if necessary Choose a well ventilated area with temperatures above 45 F 7 C and below 110 F 43 C The unit should not be located next to ovens grills or other sources of high heat Installation of the ice maker requires a cold water supply inlet of 1 4 6 35mm soft copper tubing with a shut off valve The ice maker requires a continuous water supply with a minimum pressure of 15 psig and a static pressure not to exceed 80 psig The temperature of the water feeding into the ice maker should be between 41 F 5 C and 90 F 32 C for proper operation 4 WARNING Normal operating ambient temperature should be between 45 F 7 C to 110 F 43 C Normal operating water temperature should be between 41 F 5 C and 90 F 32 C Operation of the ice maker for extended periods outside of these normal temperature ranges may affect production capacity It is strongly recommended that a water filter be used A filter if it is of the proper type can remove taste and odors as well as particles Some wat
13. at the number below Please have your model and serial number at hand Model AZ 20A or BC 900D or SC 900D Serial Number Write your serial number here for future reference OWNER REGISTRATION Please take the time to fill out and return a Warranty Registration Card or on line at www acksongrills com or simply fill in the form below and mail or fax to Jackson Grills Customer Support Tel 1 888 287 3333 or 1106 2480 Mt Lehman Rd Customer Support E mail info jacksongrills com Abbsisford BC Fax 1 877 855 5373 Canada V4X 2N3 Pars Ordering Contact your Dealer Please complete and return within 30 days Thank you Title Mr Mrs Ms Miss Circle one First Name Initial Last Name Street Apt 4 City State Prov Zip Postal Phone Email Date Purchased Dealer Model Serial Comments Thank you for taking the time to fill out this Ownership and Registration Card Dear Owner please keep this manual for future reference
14. ave the door open to allow for circulation and to prevent mold and mildew 8 Leave water supply line and power cord disconnected until ready to reuse IMPORTANT Do not touch the power plug when your hands are wet Never unplug the unit by pulling on the plug Cleaning and Maintenance CAUTION If the ice maker is left unused for a long time before the next use it must be thoroughly cleaned Follow carefully any instructions provided for cleaning or use of sanitizing solution Do not leave any solution inside the ice maker after cleaning Periodic cleaning and proper maintenance will ensure efficiency top performance and long life The maintenance intervals listed are based on normal conditions You may want to shorten the intervals if you have pets or there are other special considerations What should not be done Never keep anything in the ice storage bin other than ice objects like wine and beer bottles are not only unsanitary but the labels may slip off and plug up the drain What parts should be kept clean There are 5 things to keep clean 1 The exterior 2 The interior 3 The condenser 4 Water distribution tube 5 The ice making system 4h WARNING Before proceeding with cleaning and maintenance operations make sure the unit s power line is disconnected and the water line is shut off EXCEPTION Cleaning of ice making system Exterior Cleaning The door and cabinet may be cleaned wi
15. ce stated range The ice storage bin is full of Remove some ice be sure ice full ice probe is free of ice The body of the ice The ground line isn t in the Use a socket meeting the required maker is electrified socket electrical standard Scaling occurs frequently inside the machine The water is too hard Using a water softening device installed in front of the water inlet Water leaks from the ice storage bin The drain hole below the ice storage bin is blocked The drain hose is kinked or improperly placed higher than the floor of the ice storage bin Pull out the ice storage bin and clean the drain hole Check the drain hose to make sure the water can drain out unhindered 26 Jackson Grills Limited Warranty Description of Limited Warranty This limited warranty is given by Jackson Grills to the original purchaser of the refrigeration equipment supplied by Jackson Grills as long as the equipment remains in the possession of the original purchaser Your Jackson Grills refrigeration equipment is warranted against defects in workmanship or material for a period of one year from the date of purchase under the following requirements 1 Registration card must be completed and mailed back to Jackson Grills within 30 days from purchase area 2 Proof of purchase must be submitted for warranty consideration 3 Defects must be proven to the satisfaction of Jackson Grill
16. ce maker has been designed for Mobile free standing Enclosed as under a cabinet or Built in sealed installation indoor or outdoor In any case there must be adequate air space around the unit for proper ventilation See diagrams on page 8 Mobile installation A mobile installation will allow you to install the ice maker free standing in any place you desire provided you have access to a water supply You must follow the stated instructions for a Electrical requirements b Water supply c Leveling the ice maker Enclosed Installation An enclosed installation will allow you to install the ice maker under a cabinet or inside a kitchen cabinet provided the required clearance space around the ice maker is respected This installation has the same requirements as a mobile installation Built in Installation If this method of installation is chosen it will still be necessary to allow adequate ventilation space around the unit The following additional items must be observed 1 Place ice maker in front of installation location Remove the legs and place the unit flat on the floor or on a platform depending on your installation requirements 2 The water supply line must be plumbed before connecting to the ice maker 3 Connect the drain hose 4 Turn on main water supply and tap Check for water supply connection leaks Tighten every connection including connections at the water inlet 5 If the electrical outlet for the ice m
17. e stage stage 2 After three minutes the machine will automatically go into the ice making stage and the sound of flowing water will be heard 3 When the batch of ice has been fully formed the ice will automatically be harvested to the ice storage bin 4 When the ice storage bin is full the sheet of cubes does not fall completely and it holds the ice full probe open The machine stops making ice automatically 5 The unit will start making ice again after the ice cubes are removed Then the ice full probe swings back to operating position IMPORTANT e Although the unit has been tested and cleaned at the factory due to long term transit and storage the first batch of cubes must be discarded e Never turn the water supply tap off when the ice maker is working e Never touch the evaporator when the machine is running e Except to take ice from the unit keep the door closed to reduce ice melting and insure proper ice formation How the Machine Makes Ice Turn the Power switch to the ON position The Power indicator light will light and the machine will automatically go into the ice making stage There are two distinct cycles freeze and harvest During the freeze cycle water flows to the evaporator surface In the harvest cycle the ice is released A complete cycle can take 15 to 40 minutes depending on temperature and operating conditions Freeze During the freeze cycle the compressor is pumping ref
18. er is very hard softened water may result in white mushy cubes that stick together De ionized water is not recommended The ice maker must be installed with all electrical and water connections in accordance with all state and local codes The unit should be located on a firm and level surface It is important for the ice maker to be leveled in order to work properly If needed you can adjust the height of the ice maker adjustable feet See the Leveling the Ice Maker section A standard electrical supply 115V AC only 60Hz 15A properly grounded in accordance with the National Electrical Code and local codes and ordinances is required IMPORTANT Do not kink or pinch the power supply cord between the ice maker and wall or cabinet Electrical Requirements 4 DANGER 4h e Electrical Shock Hazard Plug into a grounded 3 prong outlet Never remove the ground prong from the plug Never use an adapter Never use an extension cord Failure to follow these instructions can result in fire electrical shock or death Before you move your ice maker into its final location be sure you have the proper electrical connection A standard electrical supply 115V AC only 60Hz 15A properly grounded in accordance with the National Electrical Code and local codes and ordinances is required The ice maker should always be plugged into its own individual electrical outlet It is recommended that a separate circuit servi
19. ing Use 2 or more people to move amp install ice SAVE THESE INSTRUCTION IMPORTANT SAFEGUARDS Before the ice maker is used 1t must be properly positioned and installed as described in this manual so read the manual carefully Jackson Grills strongly recommends that you have a professional install your new machine The warranty may be affected or voided by an incorrect installation To reduce the risk of fire electrical shock or injury when using the ice maker follow basic precautions including the following A DANGER di Plug into a grounded 3 prong outlet Do not remove grounding prong do not use adapter and do not use an extension cord It is recommended that a separate circuit serving only your ice maker be provided Use receptacles that cannot be turned off by a switch or pull chain Do not connect or disconnect the electric plug when your hands are wet Never unplug the icemaker by pulling on the power cord Always grip the plug firmly and pull straight out from the outlet Never clean ice maker parts with flammable fluids Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance The fumes can create a fire hazard or explosion Before proceeding with cleaning and maintenance operations make sure the power line of the unit is disconnected and the water line is shut off EXCEPTION When cleaning the machine s ice making and water systems See pages 21 22
20. inly for service When this is pressed over 3 seconds the unit will enter the Ice Size Adjustment mode The mode can be judged from the status of the green LED 23 Ice Size Adjustment Guide 1 Press and hold the Adjust button for at least 3 seconds The unit will enter the Ice Size Adjustment mode The ICE MAKING LED green will be blinking continuously during the ice size adjustment Release the button when the LED blinks continuously to adjust the ice size 2 While in the Ice Size Adjustment mode press the Clean button or the Mode button for the desired ice size Smaller ice setting By pressing the Clean button you can decrease the size of the ice cubes The ICE FULL LED red will flash as you lower the ice size and will finally be blinking at the setting of smallest ice size Larger ice setting By pressing the Mode button you can increase the size of the ice cubes The ICE HARVEST LED yellow will flash as the larger size is set and will blink when the setting of largest ice size has been reached After 10 seconds without any operation the unit will automatically memorize the current state and return to the previous mode NOTE e During the ice size adjustment the ICE FULL ICE MAKING and ICE HARVEST LEDS blinking all at once indicate that the unit is in the regular middle setting of the ice size e When the machine is in the cleaning stage or ice fu
21. ion of warm water and a mild detergent such as dishwashing liquid After removing the dirt and lint from the surface rinse the tube with clean water 5 Replace the distribution tube 6 Reconnect the water supply Ice Making System Cleaning Minerals that are removed from water during the freezing cycle will eventually form a hard scaly deposit in the water system Cleaning the system regularly helps remove the mineral scale buildup How often you need to clean the system depends upon how hard your water is or how effective your filtration may be With hard water of 15 to 20 grains gal 4 to 5 grains liter you may need to clean the system as often as once every 6 months 1 Make sure that all the ice is off the evaporator If ice is being made wait until the cycle is completed then turn the machine OFF at the Power switch 2 Remove all ice from the storage bin 3 Keep the ice maker connected to the water supply Pour 8 oz of Nickel Safe Ice Maker Cleaner Solution into the water trough After about 5 minutes set the Power switch to ON At the same time press the Clean switch on the front of the unit and the Clean indicator light will light then initiate the Cleaning cycle The machine will run the Automatic Clean Mode NOTE The unit will automatically shut down the Cleaning program after 30 minutes or you can stop it by pressing the Clean switch again and the machine will automatically progress to the ice making stage 4
22. lation easier IMPORTANT e All installations must be in accordance with local plumbing code requirements Professional installation is recommended e Make certain that the hoses are not pinched or kinked or damaged during installation e Check for leaks after connection Tools required 1 2 open end wrenches Phillips screwdriver a Rear of unit Drain outlet Connecting the water line 1 Turn off main water supply Turn on the nearest faucet long enough to clear the line of water 2 Find a 1 2 to 3 4 vertical cold water pipe near the installation location The distance should be less than 9 feet The water supply hose provided with the ice maker is about 9 feet 3 A shut off valve must be installed to the main water supply If the water pipe has a plain piece of copper tubing attach a 1 4 O D compression union to the tubing and remove the nut 4 Connect nuts of water supply hose to the tap and connect the other end with the water inlet Tighten firmly by hand then one half turn with wrench 5 Turn on main water supply and tap Check for water supply connections leaks Tighten every connection including connections at the water inlet IMPORTANT When you connect the water supply hose and the drain hose pay attention to the indications of Water inlet and Drain outlet on the machine Drain You must connect the drain line before using the ice maker The dual dr
23. ll stage the ice size is not available for adjusting Major Functions 1 Completely automatic operation 2 When the ice storage bin is full of ice the machine stops making ice automatically It starts making ice again once the cubes are removed 3 The different colors of the LED display indicate various work modes 4 A sensitive probe and accurate timer enhance the performance of the ice maker 5 Built in compressor protection system 24 Troubleshooting Before Calling for Service If the unit appears to be malfunctioning read through the OPERATION section of this manual first If the problem persists check the Troubleshooting Guide below and on the following page The problem could be something very simple that can be solved without a service call Troubleshooting Guide Problem The machine doesn t operate Possible Cause The icemaker is unplugged Probable Correction Plug the ice maker in The fuse is blown Replace fuse if this happens call for service to check for a short circuit in the ice maker The Power switch is set at OFF Turn the Power switch to ON The ice storage bin is full of Remove some ice making sure the feed in after the machine starts ice ice full probe is free of ice The water supply tap is Turn on the water supply tap The water doesn t turned off The water supply line is not properly connected Reconnect the water supply line
24. nection Do not under any circumstances cut or remove the third ground prong from the power cord For personal safety this appliance must be properly grounded The power cord of this appliance is equipped with a 3 prong grounding plug that mates with a standard 3 prong grounding wall outlet to minimize the possibility of electric shock hazard from the appliance Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded When a standard 2 prong wall outlet is encountered it is your responsibility and obligation to have it replaced with a properly grounded 3 prong wall outlet The ice maker should always be plugged into its own individual electrical outlet which has a voltage rating that matches the rating label on the appliance This provides the best performance and also prevents overloading house wiring circuits which could cause a fire hazard from overheated wires Never unplug your ice maker by pulling on the power cord Always grip the plug firmly and pull straight out from the outlet Repair or replace immediately all power cords that have become frayed or otherwise damaged Do not use a cord that shows cracks or abrasion damage along its length or at either end When moving the ice maker be careful not to damage the power cord Extension Cord Because of potential safety hazards under certain conditions it is strongly recommended that you do not use an extension cord with this ice maker
25. ng only your ice maker be provided Use receptacles that cannot be turned off by a switch or pull chain The fuse or circuit breaker size should be 15 amperes Recommended grounding method For your personal safety this appliance must be grounded It is equipped with a power supply cord having a 3 prong grounding plug To minimize a possible shock hazard the cord must be plugged into a mating 3 pronged and grounding type wall receptacle grounded in accordance with the National Electrical Code and local codes and ordinances If a mating wall receptacle is not available it is the personal responsibility of the customer to have a properly grounded 3 prong wall receptacle installed by a qualified electrician Leveling the Ice Maker It is important for the ice maker to be leveled in order to work properly otherwise water will not flow as it should through the evaporator ice mold Ice production will be less than normal and operation will be noisy The ice maker can be raised or lowered by four leveling legs on the bottom of the machine If you find that the surface is not level You may need to make several adjustments to level the machine We recommend using a carpenter s level to check it 1 Place a carpenter s level on top of the product to see if the ice maker is level from front to back and side to side 2 Adjust the height of the legs as follows Turn the leveling legs to the right to lower that side of the ice
26. rigerant the fan motor is blowing air and the water pump is circulating water When the batch of ice has been fully formed the ice maker stops the freeze cycle and begins the harvest cycle Harvest During the harvest cycle the compressor is still operating but the water pump has stopped The hot gas valve opens diverting hot refrigerant gas into the evaporator The hot refrigerant gas warms the evaporator causing the cubes to slide as a unit off the evaporator and into the storage bin The freeze cycle will restart when all the cubes have been harvested How the Machine Uses the Water The ice maker begins with a fixed charge of water that is contained in the water trough As the water flows to the freezing evaporator surface the portion of water that does not contain mineral impurities will freeze and stick to the ice cube molds The water containing impurities falls back into the water trough During the ice making process fresh water enters the water trough continuously as the water from the trough freezes continuously on the evaporator Evaporator Water inlet NJ MI gt water pump
27. s to have been caused by defects in workmanship or material Jackson Grills may request that defective parts be returned for inspection at the owner s expense 4 The owner is responsible for the following a All freight charges b Damage sustained in transit c Mileage charges for service calls d Proper installation e Alterations to original equipment f Removal or installation g All labour costs 5 During the Limited Warranty parts for the repairs will be provided by Jackson Grills In warranty repair must be performed by factory authorized service centers For authority to proceed with repairs contact Jackson Grills Warranty Department 106 2480 Mt Lehman Road Abbotsford British Columbia Canada V4X 2N3 Tel 1 888 287 3333 27 Special Message to Our Customers All of us at Jackson thank you for choosing a Jackson Grills product This appliance was designed engineered and built with quality components and we are confident that it will provide you with years of excellent operation Please take the time to read the entire manual and familiarize yourself with all of the features of the product This manual also contains important safety information and operation instructions Please write your products serial number in the space below and ensure that this manual remains handy for quick reference To obtain replacement parts for your product contact your local dealer If you have any questions please call us anytime
28. t like any other food container La WARNING DO NOT use solvent based cleaning agents or abrasives on the interior These cleaners may transmit taste to the ice cubes and damage or discolor the interior Condenser Cleaning A dirty or clogged condenser prevents proper airflow reduces ice making capacity and causes higher than recommended operating temperatures that may lead to component failure Have the condenser cleaned at least once every six months 1 Unplug the ice maker or disconnect power 2 Remove the 2 screws on the front cover and gently pull it off Condenser 3 Remove dirt and lint from condenser and the unit Saca compartment with a brush attachment on a vacuum cleaner 4 Reassemble the front cover 5 Plug in the ice maker or reconnect power 20 Water Distribution Tube Cleaning When you find that the ice cubes are incompletely formed or the output of ice cubes is low the water distribution tube may be blocked Set the Power switch to OFF gently take out the water distribution tube and locate the holes in the distribution tube Using a toothpick or similar tool dredge the holes then put the water distribution tube back to its original position If the tube is badly blocked clean it as follows 1 Shut off the water supply 2 Disconnect the water hose from the distribution tube 3 Gently take out the distribution tube 4 With a brush clean the tube with a dilute solut
29. th a mild detergent and warm water solution such as 1 oz of dishwashing liquid mixed with 2 gallons of warm water Do not use solvent based or abrasive cleaners Use a soft sponge and rinse with clean water Wipe with a soft clean towel to prevent water spotting Stainless steel can discolor when exposed to chlorine gas and moisture Clean stainless steel with a mild detergent and warm water solution and a damp cloth Never use an abrasive cleaning agent 19 Interior Cleaning The ice storage bin should be sanitized occasionally Clean the water trough before the ice maker is used first time and reused after stopping for an extended period of time It is usually convenient to sanitize the trough after the ice making system has been cleaned and the ice storage bin is empty 1 Disconnect the power to the unit 2 Open the door and take out the removable ice storage bin With a clean cloth wipe down the interior of unit and ice bin with a sanitizing solution made of 1 ounce of household bleach or chlorine and 2 gallons of hot 95 F 115 F water 3 Pull off the drain hose of the water trough to drain off all water Rinse thoroughly with clear water 5 After draining off all water put back the drain hose of the water trough to the original location iat leadon dl the drain hose 7 Reconnect power to the unit E 6 Put the ice storage bin inside the unit The ice scoop should be washed regularly Wash it jus
30. thout prior notice Ice Maker Safety Your safety and the safety of others are very important We have provided many important safety messages in this manual and on your appliance Always read and obey all safety messages This is the Safety Alert Symbol This symbol alerts you to potential hazards that can injure or kill you and others All safety messages will follow the Safety Alert Symbol and either the words DANGER 4 DANGER amp amp WARNING CAUTION WARNING OR CAUTION DANGER means that failure to heed this safety statement may result in severe personal injury or death WARNING means that failure to heed this safety statement may result in extensive product damage serious personal injury or death CAUTION means that failure to heed this safety statement may result in minor or moderate personal injury or property or equipment damage All safety messages will alert you to what the potential hazard is tell you how to reduce the chance of injury and let you know what can happen if the instructions are not followed IMPORTANT SAFETY INSTRUCTIONS WARNING To reduce the risk of fire electric shock or injury when using your ice maker follow these basic precautions Plug into grounded 3 prong outlet Do not remove grounding prong Do not use an adapter Do not use an extension cord 7 Disconnect power before cleaning Disconnect power before servicing Replace all panels before operat
31. torage bin CLEAN indicator light CLEAN switch Power indicator light ON OFF switch adjustable foot Control panel cover Power cord Water inlet Drain outlet Ice scoop NY AN YY gt Drain hose Water supply hose Ice Maker Installation Unpacking WARNING Excessive Weight Hazard Use two or more people to move and install ice maker Failure to do so can result in back or other injury Remove packaging materials IMPORTANT Do not remove any permanent instruction labels or the data label on your ice maker Remove tape and glue from your ice maker before using e To remove any remaining tape or glue rub the area briskly with your thumb Tape or glue residue can also be easily removed by rubbing a small amount of liquid dish soap over the adhesive with your fingers Wipe with warm water and dry e Do not use sharp instruments rubbing alcohol flammable fluids or abrasive cleaners to remove tape or glue These products can damage the surface of your ice maker Cleaning before use After you remove all of the packaging materials clean the inside of your ice maker before using it See Interior cleaning in the Cleaning and Maintenance section Location Requirements Top View Side View va re Rear of unit Top of unit Side mite Front of unit Se Ss INSTALLATION CLEARANCES 8 This ice maker should be installed by qu
Download Pdf Manuals
Related Search