Home
user manual / instructions
Contents
1. with overlap center part all feets all fabric parts iy id i WK hil d Hog l t i IH T STN j ji i if ih J n vs an pp Yi iH J Hi i WE ally A Peat edi Pew ALLAT a ih 10 pcs cord fastening nails are included in each expoarch User manual instructions expoarch eXpotrade www expotrade at Bag 3 tube system right side X Y Z incl triangle Weights bag fillable with 30 I water or sand and or plates of 25 kq each page 4 of 11 2011 2012 without written notice of Expotrade Group GmbH this manual may not be copied unless for own usage Fxpotrade Group 8mb user manual instructions e po Herrschaftswiesen 17 poa www expotrade at 6842 Koblach y expotrade 3 Assembly 1 First please take out the tubes from each bag and start with laying the center part to the center of the planned location The center part is easy to recognize as this is the part with 3 tubes welded together to one piece Then lay all the tubes left A B C and right side X Y Z of the center part to the ground by following the numbers code on the tubes e g A 1 to A 1 and X 6 to X 6 etc The numbers are clearly indicated at each profile Please mind that the bending of the center part has to look upwards and the sides touch the ground 2 Lift up the center part and start to plug in the tubes according to the number code Please mind th
2. after each other please DONOT loose all 3 bars together at the same time The 2 other bars always have to stay fixed in the holder By doing this all the 3 bars will be hided completely inside the fabric part Then you may continue in fixing the fabric downwards around the tubes At the end there is a ribbon buckle fixing which has to be properly and carefully fixed at the feets in order to reach nice tension of the fabric Please DONOT overtension User manual instructions expoarch page 8 of 11 2011 2012 without written notice of Expotrade Group GmbH this manual may not be copied unless for own usage Expotrade Group GmbH User manual instructions yy Herrschaftswiesen 17 www expotrade at 6842 Koblach by expotrade 1 Make sure that you twist the height adjustment at each of the legs accordingly so long up or down until the expoarch is in a most equal level Soft ground In the feets are holes where you have to push in the long nails 10 pcs nails with 70 cm length are included 6 nails for the legs 4 nails for the cords Hard ground Either weight bags or weight plates can be used The weight bag can be fixed at the inside hided by the fabric parts and the weight plates are fixed at the feets so that they cannot slip off the plate Wa 2 Depending on windspeed the expoarch has to be additionally tightened down by cords ribbon which are included as well Either these are fixed with the nails
3. manual instructions expoarch page 2 of 11 2011 2012 without written notice of Expotrade Group GmbH this manual may not be copied unless for own usage Expotrade Group GmbH User manual instructions e po Herrschaftswiesen 17 6842 Koblach www expotrade at eXpoarch by expotrade e Please note that the single components of the expoarch can be heavier in weight as maybe expected e The expoarch may not be buildt up during windspeeds of over 50 km h Once the expoarch Is properly buildt up and securely fixed please take attention of the special instructions regarding wind speeds e Always securely fasten the expoarch with the included tightening cords The cords can be fixed either with long nails min 50 cm length in the soft ground or be fixed at other positions which can hold the weight and tension properly If you donot use the cords properly please be warned that you risk a damage or injury Depending on the windspeed and or at locations with no cord fixing possibilities you may also use weights additionally to the cords Please notice the special instructions regarding necessary weight e At windspeeds of 60 km h or more the expoarch has to be taken down immediately or at least all the fabric parts has to be taken off the frame e Incase the profiles of the expoarch are inside the track of any race please make sure that the profiles are properly covered at least up to 2 m height with any bumping effect foam f
4. Expotrade Group GmbH User manual instructions e po eXpoarch Herrschaftswiesen 17 6842 Koblach www expotrade at by expotrade User manual instructions expoarch page 1 of 11 2011 2012 without written notice of Expotrade Group GmbH this manual may not be copied unless for own usage Expotrade Group GmbH User manual instructions e po eXpoarch Herrschaftswiesen 17 6842 Koblach www expotrade at by expotrade 1 warn and security notice e The expoarch design and construction is destined to be used indoor and outdoor e To ensure a safe stand the build up and take down has to be in accordance with this user manual and the instructions herein has to be followed exactly e The build up and take down is allowed only by persons which are familiar with this user manual and instructions herein e Expotrade Group GmbH their affiliates or the manufacturer cannot be held responsible for any damages at the product or also damages on other products or persons caused by any misuse wrong operation or inappropriate repairs e f available please use gloves best with a rubber coating to avoid dirty hands touching the fabric parts and to avoid any injury on your hands fingers e Any necessary repair may be carried out only by Expotrade Group GmbH or their announced and or authorized persons or companies e Incase of any transfer of the expoarch to Third Parties you have to ensure that the user manual and instruct
5. abric or other proper material avoiding injuring while crashing into the expoarch e DONOT o climb on the expoarch o hang on any position of the expoarch o hang any weights on to the expoarch which are not confirmed by Expotrade o pull on the fixing cords o Carry or move the expoarch to another position after it is buildt up o hang any light sources in or on it which may get warm or hot o place the expoarch at a location where emergency and or other vehicles have to enter o hang any additional fabric parts on or in it which are not confirmed by Expotrade o throw the profiles or any parts of the expoarch to the ground this might damage the profiles and therefore effect the stability and or disturb the build up or take down process seriously o drive with any vehicle on the parts or jump on to the parts o Clean the profiles with any strong chemical which may damage the coating or welding o stow other products on the packed expoarch this may bend the profiles and or damage the packing bags User manual instructions expoarch page 3 of 11 2011 2012 without written notice of Expotrade Group GmbH this manual may not be copied unless for own usage Expotrade Group GmbH Herrschaftswiesen 17 6842 Koblach 2 Equipment Bag 4 vw tube system left side A B C incl triangle Fabric parts are packed on top of the bag 2 use the overlap to protect user manual instructions eXpo by expotrade Bag 2
6. at you always alternate left and right side from the center part so that the expoarch is equally growing up Two persons equally holding up the arch and one person is pushing in the profiles one by the other at these positions If both profiles are properly in then move to the other side of the arch and continue to do the same equally on that side Once done then again move to the other side and continue like this till the arch is up IMPORTANT DONOT yet push any middle tube into the center part only start with the side legs Otherwise the whole weight is on the middle part and the arch may fall to any side User manual instructions expoarch page 5 of 11 2011 2012 without written notice of Expotrade Group GmbH this manual may not be copied unless for own usage Fxpotrace Group Smb user manual instructions ey Herrschaftswiesen 17 6842 Koblach www expotrade at eXpoarch by expotrade 3 Most important is that the snap button golden colour is properly popping out at the hole of the connection part as otherwise the profile is NOT fixed properly and the expoarch is not standing securely There is a small mark at each connection part in order to better see the correct pushing in position of the tube If followed by this mark the snap button should pop out automatically once the profile is pushed in completely if not then twist the tube a bit But please note that any twisted push in
7. ions are available with the product in order that a proper build up and take down as well as the proper and secured fixing of the expoarch is guaranteed In case the user manual is not available you may contact Expotrade Group GmbH or download from www expotradegroup com e While mounting the profiles please carefully watch your fingers hands of crushing e Near the expoarch fabric donot handle with open fire and other sources of ignition e Please make sure that the planned location of the expoarch is as equal as possible smaller height discrepancies can be adjusted with the height adjustment which is integrated in each of the leg A non equal position might result in damaging the expoarch itself and could lead to a fall down Expotrade Group GmbH cannot be held responsible of any damage and injury caused thereof e During build up and take down of the expoarch it has to be ensured that persons which are not familiar with the user manual and instructions or which are not involved in the build up and take down procedure are not in the nearer surrounding of the expoarch Furthermore please ensure that all vehicles or other products whatsoever which might disturb the build up or take down process or be damaged by a falling expoarch are in secure distance of the location e To build up and take down of the expoarch you need at least 3 persons more persons recommended which are familiar with the user manual and instructions accordingly User
8. of the profile may cause j that the profile gets stucked in the connection part In this occasion please keep on holding the arch equally and try to pull out the profile by carefully shaking and twisting the profile until it is released DONOT let the expoarch stand down in this condition if only one profile is properly in By doing so the profile might get stucked even more or the expoarch could fall down 4 To enlarge the stability of the expoarch the upper triangle has to be fixed between the 2 and 3 tube starting from the center part Before you push in the 3 tube you have to place the triangle on top of the connection part of the tube connection part into the hole of the triangle and then push in the 3 tube together with the triangle into the a tube Please mind the correct position of the triangle before you push finally 5 IMPORTANT Only after you have fixed the upper triangle you may start fixing the middle tubes which are pushed into the middle tube of the center part Also do it left right side after each other Always note that the middle tube has to be one step behind the two outer tubes as otherwise the whole weight of the expoarch is laying on the middle tube and might damage the expoarch or even fall down during build up User manual instructions expoarch page 6 of 11 2011 2012 without written notice of Expotrade Group GmbH this manual may not be copied unless for own usage Exp
9. or also tightened down to any other position which can hold the weight tension of the expoarch On both sides during stronger winds The cords ribbon has to be fixed at the upper triangle part see the red line below User manual instructions expoarch page 9 of 11 2011 2012 without written notice of Expotrade Group GmbH this manual may not be copied unless for own usage Fxpotrace Group sme User manual instructions WY Herrschaftswiesen 17 eXp oarc h by expotrade FINISHED www expotrade at 6842 Koblach important notice for the TAKE DOWN procedure 1 Please consider all security steps as mentioned above security distance of persons not involved vehicles or other items which remain unchanged and still valid also for take down procedure 2 Start with loosing the fabric fixings at the bottom and continue upwards 3 The lower triangle bars may be taken out only one by one and after releasing the fabric they HAVE TO BE FIXED AGAIN 4 All steps have to be done always alternating on both sides 5 Opposite to the build up procedure the middle tubes HAVE TO BE TAKEN OUT FIRST and the outer tubes are one step behind IMPORTANT 6 Also MIND that the long bar has to remain at the bubble holder as long as possible necessary in order to keep the stability or the expoarch 7 Just MIND that the expoarch is equally taken down on both sides left and right so please DONOT take do
10. otrade Group GmbH User manual instructions e po Herrschaftswiesen 17 eXp Oarc h by expotrade www expotrade at 6842 Koblach 6 After you have fixed the triangle then you can push in the 4 tube on left and right side so that the expoarch is nicely and equally standing on a wider leg distance If this is completed you could start fixing the fabric banner below the center part The Spannfix fixings has to be slinged around the middle tube and be fixed also at both triangle parts inside After fixed at the triangle you may have to adjust the fixing around the middle leg accordingly in order to get a nice and tensioned shape at the banner Then you may continue in fixing the left and right fabric parts with the smaller open triangle on top Please mind the correct triangle position and fix it with the ribbon buckles at the triangle Furthermore start to sling around the Spannfix fixings to all three tubes and continuesly fixing downwards 7 By continuing in pushing the next profiles in you will notice some additional welded holders at the tubes These are holders of necessary additional lower triangle bars These bars will give the expoarch additional stability at the lower part of the arch and are absolutely necessary At this position the LONG BAR MUST be clicked into the bubble holder immediately Only if the long bar is clicked into properly you may proceed with the other side of the expoarch to do the
11. same procedure lf you forget to fix the long bar on the one side and lift the expoarch on the other side the expoarch might be damaged and even fall down This is a very Important step User manual instructions expoarch page 7 of 11 2011 2012 without written notice of Expotrade Group GmbH this manual may not be copied unless for own usage Expotrade Group GmbH User manual instructions e po Herrschaftswiesen 17 eXp oarc h by expotrade www expotrade at 6842 Koblach 8 After both long bars are properly clicked into the bubble holder you may proceed with the feets on both of the outer tubes DONOT start with the middle leg as this one is still one step behind Once you have done this on both sides left and right then proceed on one side with the middle feet and then on the other side as well In order to push in the middle feet the 2 persons holding up the outer tubes equally have to lift up quite high in order to be able to push in the middle tube incl feet Once this is done then you have to immediately FIX THE SHORT BARS as well 9 Further fix the fabric at the tubes downwards and stop at the lower triangle position Reaching this position you will notice a small cut out at the side of the fabric First you have to loose one bar from the bubble holder and push the bar from the outside into this cut out Then fix the bar again at the bubble holder This procedure has to be done with all 3 bars one
12. wn first one side completely and then the other side This may result in instability of the expoarch and might damage the product or persons items etc under it seriously when falling down User manual instructions expoarch page 10 of 11 2011 2012 without written notice of Expotrade Group GmbH this manual may not be copied unless for own usage Expotrade Group GmbH User manual instructions e po Herrschaftswiesen 17 6842 Koblach www expotrade at eXpoarch by expotrade Warranty and contact information Warranty Expotrade Group GmbH warrants the product for 2 years from date of delivery against defects in materials and workmanship This warranty does not cover any defects caused by accident misuse fire tearing of fabric due to inproper handling neglect or any attempt at repair This warranty is offered as an additional benefit to the consumer s statutory rights and does not affect these rights in any way Contact Head office Expotrade Group GmbH Herrschaftswiesen 17 6842 Koblach Austria EU P 43 0 5523 54010 office expotrade at www expotradegroup com User manual instructions expoarch page 11 of 11 2011 2012 without written notice of Expotrade Group GmbH this manual may not be copied unless for own usage
Download Pdf Manuals
Related Search
Related Contents
Pro Stepper Service Manual Trane VUVE Vertical Classroom Installation and Maintenance Manual Indoor/Outdoor Analog Wireless Camera with Receiver User Manual Oracle FLEXCUBE Direct Banking Retail Credit Card Peavey Stadia II User's Manual ITLD-880 - instrutemp.provisorio.ws Manual de Usuario - Secretaria de Ciencia y Tecnica ストリームキットで始まる お庭に小川のある生活 GBC KM1000PB User's Manual PEG-S300 Read This First - Manuals, Specs & Warranty Copyright © All rights reserved.
Failed to retrieve file