PASSIVE LOOP-POWERED ISOLATION TRANSMITTER Iin & Iout
Contents
1. AFTER SALES SERVICE 1 Products are carefully inspected and quality control during production and before shipment If they operated abnormally or there were anything wrong please contact our agent where purchased or MORNSUN FAE as soon as possible 2 MORNSUN warranty our product for 3 years from manufacturing date During this peroid MORNSUN will repair or replace the product if product was found to have manufacturing defect APPLICATION CIRCUITS You can see A APPLICATION GUIDE TO ISOLATION TRANSMITTER APPLICATION CIRCUIT DIAGRAM amp SCHEMATIC DIAGRAM 12 Ai 1 PLC k Vin Circuit T lin p Transducer Ri rh ream 4 20mA 12 2 PACKAGING SIZE AND PIN DESCRIPTION 1 00 0 039 oe 0 50 0 020 L Note grid 2 54 2 54mm 5 60 0 220 Ww N gt e z A Pt D i 1 50 0 059 7 90 0 311 10 10 0 398 PIN CONNECTION Pin Function 1 Vin Power input Note 2 Io Current output Unit mm inch 9 10 lin Current input General tolerances 0 50 0 020 Sige aie L 530 20 866 Tube Quantity 15pcs r 11 12 Vout P L 220 8 661 Tube Quantity 6pcs ee ee Inner carton S L W H 255 170 80 nema Pore Outer carton S L W H 375 280 270 6 inner cartons S Pi2. A Output With Load Ability in Us 5 0 02 loop power supply voltage Load Load Regulation 0 05 F S 100Q TRANSMISSION SPECIFICATIONS Zero Offset 0 3 F S Gain Error 0 3 F S Temperature drift coefficient 0 0035 F S C 25 C 71 C ISOLATION SPECIFICATIONS Galvanic Isolation Two port isolation Between signal input and signal output Isolation Voltage 3KVDC Tested for 1minute leakage current lt 1mA humidity lt 70 Insulation Resistance 100MQ 500VDC Between signal input and signal output OTHER CHARACTERISTICS l Operation temperature 25 C 71 C Ambient Temperature Transport and Storage temperature 50 C 105 C Weight 8g typ Application Environment No dust fierce vibration impulsion and corrosive gas The copyright and authority for the interpretation of the products are reserved by MORNSUN T1100L F 2013 07 09 A 2 Page 1 of 2 Note 1 All specifications measured at TA 25 C humidity lt 75 the value of nominal input and rated output load unless otherwise specified 2 All characteristics are meant for listed model non standard models may perform differently you can contact MORNSUN FAE for more details NOTICE 1 Please read the user manual carefully before using If any question please contact our technical support department 2 Please do not use this product in hazardous area 3 To avoid invalid explosion protection function or any failure users disassemble this product is forbidden
3. MORNSUN PASSIVE LOOP POWERED cane with Over current Protection ISOLATION TRANSMITTER Accuracy 0 1 F S lin amp lout High isolation voltage 3KVDC 60s High linearity 0 3 F S _T1100L F Extremely low temperature drift 85PPM C High reliability MTBF gt 500 000 hours GENERAL DESCRIPTION PART NUMBER SYSTEM T1100L F Isolation transmitter is a kind of two wire loop T1100L F powered isolation module The output device could receive the signal from input instrument also powered the input instrument throughT 1100L F Adopting unique electromagnetism Loop powerd isolation design and high efficiency loop electric larceny Package technology independent power supply is not required for the Isolation power output module realizing 4 20mA standard signal isolation with high aa ac curacy it match to kinds of equipment mod ule input et eae attachment PLC DCS act Over current Protection is designed et ae eater to protect the isolation module and the latter circuit Besid es the module have extremely low temper ature drift no more than 35PPM C under 25 C 71 C The isolation voltage between the input and output can be up to 83KVDC SELECTION GUIDE loop Power Supply Maximum loop Power Voltage Supply Voltage Input Output Channels Package Note Exceeding the maximum loop power supply voltage will damage the product ELECTRICAL SPECIFICATIONS Type 5V input 20m
4. n section to eee Inner carton L L W H 580 200 100 General tolerances 0 50 0 020 Outer carton L L W H 600 215 220 2 inner cartons L THIRD ANGLE Outer carton L L W H 600 215 325 3 inner cartons L PROJECTION c 11100009104 AO Note 1 All specifications are measured at Ta 25 C humidity lt 75 the value of nominal input and rated output load unless otherwise specified 2 In this datasheet all the test setup and methods are based on our corporate standards 3 All characteristics are for listed models and non standard models may perform differently Please contact our technical support for more detail 4 Contact us for your specific requirement 5 Specifications are subject to change without prior notice MORNSUN Science amp Technology Co Ltd Address No 5 Kehui St 1 Kehui development center Science Ave Guangzhou Science City Luogang district Guangzhou P R China Tel 86 20 38601850 Fax 86 20 38601272 E mail info mornsun cn Http www mornsun power com The copyright and authority for the interpretation of the products are reserved by MORNSUN T1100L F 2013 07 09 A 2 Page 2 of 2
Download Pdf Manuals
Related Search