Home

ReliTouch User Manual

1. s 85 USER ENROLLMENT TABLES cssssscscccccccssssscscccccccccssssssceccees 87 ReliTouch User Manual 3 i Actuator G Systems http www advancedactuators com ReliTouch RT 201 Installation Guide Section 1 Parts Please familiarize yourself with all the parts in the packaging box of ReliTouch RT 201 If any part is missed or damaged contact your dealer immediately i Ly Indoor Unit Universal Handles Strike Plate amp Box Rubber Gaskets Fixing Plate Tubular Latch Over ride Keys 2 3 8 amp 2 3 4 Spindle or tailpiece adjustable ReliTouch User Manual 4 Actuator Systems http www advancedactuators com Qne long thin shafted Phillips Head Screwdriver ReliTouch User Manual 5 Actuator Systems http www advancedactuators com Section 3 Pre installation 3 1 Mark and bore holes on the door 3 11 Use the following steps to properly mark holes on door for drilling 1 Remove existing handle set 2 Cut out the two 3 8 holes on the Installation Template that correspond to your existing backset 2 3 8 or 2 74 ReliTouch User Manual 6 W kaai http www advancedactuators com 3 Rest the installation template on the front of the door on top of the existing 2 1 8 hole making sure that it is aligned properly for the door s existing 2 3 8 or 2 3 2 backset 4 Mark the two 3 8 holes th
2. e When setting for Saturday is completed press E Message Save will display on the LCD Pref e Press M message Saved will display OR press E to exit without saving ReliTouch User Manual 52 Actuator Systems http www advancedactuators com Section 2 Administrator and User Setup NOTES Fingerprint User IDs 1 3 are Administrators meaning that they have complete access to program the ReliTouch RT 201 and to unlock the door at any time To access any menu options after an Administrator fingerprint has been enrolled the Administrator s fingerprint will need to be verified after pressing M to enter the menu options The term Fingerprint is used as a general term when describing fingers or thumbs to use for enrollment verification Before enrolling and verifying fingerprints make sure to read the following helpful hints for Fingerprint Enrollment and Verification Generally the center of the vortex swirl of the fingerprint pattern is the key data point ideally it is placed in the center of the sensor s glass window in a consistent way Your finger or thumb should be flat motionless and held with light pressure in the same way each time See the picture below for some guiding drawings Also be sure that your fingerprint is well defined where you can visibly see the well defined peaks and valleys of the vortex ridge pattern Light pressure when placing t
3. to save selection e Once the Time Frame is set up press E Message Save will display on the LCD ReliTouch User Manual 50 i Actuator Systems http www advancedactuators com e Press M Message Saved will display on the LCD OR press E to exit without saving 9 Scroll to Week Days and press M to set up the Days of the Week access for the RT 201 e Press M to choose Y Yes OR N No for each day of the week that is highlighted e If Y Yes is chosen for a specific day of the week then all enrolled Users that do not have Acc Times set up for their specific individual User ID will have access to unlock the ReliTouch RT 201 on that day of the week during the Date Range and Time Frame that has already been set up Once the Date Range or Time Frame has expired all enrolled ReliTouch User Manual 51 Cp Sar http www advancedactuators com Users will not be able to unlock the ReliTouch RT 201 Only Administrators User ID 1 3 will have access to unlock the ReliTouch RT 201 e If N No is chosen for a specific day of the week then no enrolled Users will have access to unlock the ReliTouch RT 201 for that day of the week Only Administrators User ID 1 3 will have access to unlock the ReliTouch RT 201 e Press E to exit and Up and Down arrows to scroll to the next day of the week F
4. Definitions of Indication Beeps Single Short Beep Indicates the following A button has been pressed An operational sequence has begun The door has been successfully unlocked A fingerprint user has been added successfully Three Short Beeps Indicates unsuccessful Fingerprint PIN verification attempt Six Short Beeps Low battery alert change batteries OR the lock has been reset ReliTouch User Manual 24 Actuator Systems http www advancedactuators com Definitions of LED Red LED Indicates any unsuccessful fingerprint PIN verification attempt Green LED Indicates any successful fingerprint PIN verification attempt ReliTouch User Manual 25 Actuator Systems http www advancedactuators com Section 1 Lock Setup 1 1 Programming buttons on the inside unit 1 The M button stands for Menu and is used to enter different menu options and it is also used to save changes made to the ReliTouch RT 201 3 The E button stands for Exit and this is pressed to exit individual menu options E button ReliTouch User Manual 26 Actuator Systems http www advancedactuators com NOTE The following LOCK SETUP instructions are assuming that there are no fingerprints enrolled in the ReliTouch RT 201 All LOCK SETUP functions can be done prior to enrolling an Administrator fingerprint or PIN code If changes are being made to the LOCK SETUP o
5. for the bottom fixing posts ReliTouch User Manual 21 nnn ystems http www advancedactuators com Section 5 Power Options 5 1 AA Batteries 1 Remove battery cover 2 Insert 4 AA batteries into the battery pack located on the inside unit We recommend Lithium AA batteries for longevity 1 5v only 3 When batteries are inserted two beeps are heard indicating that the lock is ready to program ReliTouch User Manual 22 Actuator Systems http www advancedactuators com 5 2 Hardwiring the ReliTouch RT 201 It is possible to hard wire the ReliTouch RT 201 to an external 6 to 12VDC 1 2 amp power supply for constant power IMPORTANT e WHEN THE RELITOUCH RT 201 IS HARD WIRED THE AA BATTERIES CAN BE LEFT IN THE BATTERY PACK FOR BACK UP POWER Only licensed electricians should hard wire the unit Actuator Systems LLC will not be held liable for faulty hardwiring ReliTouch User Manual 23 Actuator Systems http www advancedactuators com ReliTouch RT 201 Operations Manual SECURITY WARNING With no fingerprints or PIN Codes enrolled the ReliTouch RT 201 will unlock when the button is pressed on the keypad Itis strongly recommended that an Administrator User IDs 1 thru 3 DELETE ALL Fingerprints and PIN Codes Sections 1 7 and 1 8 prior to programming the ReliTouch RT 201 in the event that a User has been accidentally added prior to programming
6. i Actuator Systems http www advancedactuators com NOTE If desired the same finger thumb can also be used for fingers thumbs 2 and 3 This is recommended for Users with poor quality fingerprints However different fingers thumbs can be used for fingers thumbs 1 2 amp 3 e Press the up arrow to highlight 2N and press M e Rest the next or same desired finger or thumb on the sensor outside unit e Keep finger or thumb on the sensor while it flashes three quick times KEEP FINGER STILL DURING SCANNING ReliTouch User Manual 60 Actuator Systems http www advancedactuators com e If finger thumb 2 was successfully enrolled a single short beep will be heard the LCD will display Success and 2N will change to 2Y o If unsuccessful Failed will display on the LCD and 2N will not change to 2Y Repeat the steps above to try again e Press the up arrow to highlight 3N and press M ReliTouch User Manual 61 i Actuator Systems http www advancedactuators com e Rest the next or same desired finger or thumb on the sensor outside unit e Keep finger or thumb on the sensor while it flashes three quick times KEEP FINGER STILL DURING SCANNING e If finger thumb 3 was successfully enrolled a single short beep will be heard the LCD will display Success and 3N will change to 3Y o If unsuccessful Failed will display
7. 7 Deleting ALL Fingerprints in the ReliTouch RT 203 39 1 8 Deleting ALL PIN Codes in the ReliTouch RT 201 40 1 9 Setting up Timed Access for the ReliTouch RT 201 41 ReliTouch User Manual 2 Actuator Systems http www advancedactuators com 1 10 Choosing ANY TIME as the Access mode for the ReliTouch RT O E eee 43 1 11 Choosing INVALID as the Access mode for the ReliTouch RT xua E EE NEEE E AE EEE EA 0D z2 44 1 12 Choosing and setting up ACC TIME as the Timed Access mode for the ReliTouch RT 201 ccccccsecescccesescececescsceceevscescecsceesacecesacereeees 45 Section 2 Administrator and User Setupp cccccccccccccsssssssssssssccsees 53 2 1 Creating Editing amp Deleting User ACCESS cccccecssseceeeeseeeeeeees 55 Section 3 Unlocking the ReliTouch RT 201 77 3 1 Unlocking the ReliTouch RT 201 in 1 N Mode with an enrolled TVS Fis AUG n DD bb pJ JJ e NIJMIDEDMEZaZD p 77 3 2 Unlocking the ReliTouch RT 201 in 1 N Mode with a registered FINC OOE Nar rr r gel beb 79 3 3 Unlocking the ReliTouch RT 201 in 1 1 Mode with an enrolled MEEN o A ara ae 80 3 4 Unlocking the ReliTouch RT 201 in 1 1 Mode with a registered PINC OOC moenie be sate aarar E eee oa 82 3 5 Unlocking the ReliTouch RT 201 with the override keys 83 Support and Warranty Information
8. Scroll to ANYTIME option and press M 4 Press E to exit ReliTouch User Manual 43 i Actuator Systems http www advancedactuators com 1 11 Choosing INVALID as the Access mode for the ReliTouch RT 201 1 In the Lock setup menu scroll down to and highlight option 7 Access Time and press M ik 2 Scroll to INVALID option and press M 4 Press E to exit ReliTouch User Manual 44 i Actuator Systems http www advancedactuators com 1 12 Choosing and setting up ACC TIME as the Timed Access mode for the ReliTouch RT 201 1 In the Lock setup menu scroll down to and highlight option 7 Access Time and press M id 2 Scroll to ACC TIME option and press M ReliTouch User Manual 45 i Actuator Systems http www advancedactuators com 4 The From and To Date Range options display The format for the Date Range settings is MMDDYYYY from left to right 5 Use the up and down arrows to choose the appropriate MM DD and YYYY in each section When desired numeric value is chosen for each section press M to move on to the next date value Example Desired From date is January 15 2009 In the From section e Use the up and down arrows to enter 01 for January and press M ReliTouch User Manual 46 Actuator Systems http www advancedactuators c
9. User ID will be deleted 4 Access Time When this option is chosen it allows for timed access to be created for a specific date range days of the week and time frame within the days of the week for the Specific User ID Again any Acc Time settings that were previously made for the LOCK will override any Access Time settings for the specific User ID ReliTouch User Manual 57 i Actuator Systems http www advancedactuators com 6 To Add FINGERPRINTS to the specific User ID highlight section 1 Add FP and press M If no fingerprints have been enrolled for this User ID then 1N 2N 3N will be displayed A total of 3 fingerprints from fingers or thumbs can be enrolled for each User ID If there are fingerprints already enrolled for the User ID then Y will be displayed next to some or all of the numbers e Highlight IN and press M e Rest desired finger or thumb on the sensor outside unit ReliTouch User Manual 58 Actuator Systems http www advancedactuators com e Keep finger or thumb on the sensor while it flashes three quick times KEEP FINGER STILL DURING SCANNING e If finger thumb 1 was successfully enrolled a single short beep will be heard the LCD will display Success and 1N will change to 1Y o If unsuccessful Failed will display on the LCD and IN will not change to 1Y Repeat the steps above to try again ReliTouch User Manual 59
10. com 1 5 Setting the Lock Mode There are two choices in the Lock Mode menu Auto Also known as Auto Lock when this mode is enabled the ReliTouch RT 201 requires an enrolled fingerprint or PIN Code to be verified to unlock the door TUM TUM stands for Temporary Unlocked Mode When this is enabled the solenoid will engage and the ReliTouch RT 201 will stay unlocked until an Administrator sets the lock back to Auto Lock mode If an enrolled fingerprint or PIN code is verified on the lock when TUM mode is enabled the door will be locked temporarily Once the fingerprint or PIN is verified to unlock the door the lock will be set back to TUM automatically ReliTouch User Manual 36 Actuator Systems http www advancedactuators com Use the following steps to set up the Lock Mode at the ReliTouch RT 201 1 In the Lock setup menu scroll down to and highlight option 4 Lock Mode and press M 2 Use the up and down arrows to scroll thru the lock modes until the desired mode is reached and press M to save setting 3 Message Saved will display and there will be an audible buzz of the solenoid engaging if TUM is chosen or disengaging if Auto 1s chosen 4 Press E to exit ReliTouch User Manual 37 Actuator Systems http www advancedactuators com 1 6 Setting up the Lock ID Setting up the Lock ID of the ReliTouch RT 201 is critical when using the R
11. enrolled fingerprint was not successful on the first attempt the LED will flash red no beeps If this happens re position the enrolled fingerprint on the sensor The sensor will try two more times to verify the enrolled fingerprint If all three attempts fail the LED will flash red three times and three short beeps will be heard Remove the enrolled fingerprint and start over from the beginning of this section Also check to make sure that the fingerprint being used has been enrolled If the LED flashes red three times and three short beeps are heard after or button was pressed this indicates that the matching mode is set to 1 1 If LED flashes red once and one single beep is heard after a successful verification this indicates that User ID associated to the enrolled fingerprint is either outside of their Timed Access settings OR their User ID is set to INVALID OR the lock is set to INVALID Illuminating the ReliTouch RT 201 Exterior Unit Keypad e Press and Hold any of the numbers on the keypad 0 thru 9 for two to three seconds on the exterior unit e Keypad will illuminate ReliTouch User Manual 78 i Actuator Systems http www advancedactuators com 3 2 Unlocking the ReliTouch RT 201 in 1 N Mode with a registered PIN Code 1 Enter the registered PIN Code on the keypad of the outside unit and press star star 2 If PIN Code verification was successful two short beeps will be heard the g
12. http www advancedactuators com e 2c Fasten the screw so the handle is firmly held in place e 2d Follow steps 2a thru 2c for installation of the handle on the inside unit ReliTouch User Manual 11 Actuator Systems http www advancedactuators com Section 4 Installation NOTE Measure the exact thickness of the door and choose the pre labeled bag of screws included whose length matches the exact thickness of the door The pre labeled bag of screws will be needed in Section 4 4 4 1 Impact Alarm Information An impact alarm actuator has been mounted onto the back plate of the outside unit See the diagram for details Impact Alarm Actuator The impact alarm will sound in the event of an impact to the lock that causes the ReliTouch RT 201 outside unit to dislodge from the door If the actuator is not firmly depressed then the alarm will sound The impact alarm is located under the rubber cover on the outside unit The alarm will also sound if the outside units wire set is not fully plugged into the inside unit ReliTouch User Manual 12 Actuator Systems http www advancedactuators com If the alarm is triggered make sure to check the door and the lock immediately If there is no emergency occurring then remove the batteries to stop the alarm and check connections Do not install batteries until installation is completed and lock is installed securely on the door 4 2 Installing t
13. the lock on any temporary building such as a shed or semi permanent buildings such as a pool enclosure voids the warranty c Mounting the lock on any porous surface This includes materials such as grooved woods or any surface that prevents the rubber grommet from sealing the lock to the surface of the door 3 Modification of the ReliTouch in any way 4 Expedited shipping for replacement units this is available when you submit the RMA you just pay the difference over ground ship ReliTouch User Manual 86 Actuator Systems http www advancedactuators com USER ENROLLMENT TABLE Hand R or L Finger Used PIN CODE ReliTouch User Manual 87 Actuator Systems http www advancedactuators com ReliTouch User Manual 88 Actuator Systems http www advancedactuators com ReliTouch User Manual 89 Actuator Systems http www advancedactuators com ReliTouch User Manual 90 Actuator Systems http www advancedactuators com ReliTouch User Manual 91 Actuator Systems http www advancedactuators com ReliTouch User Manual 92 Actuator Systems http www advancedactuators com ReliTouch User Manual 93 Actuator Systems http www advancedactuators com ReliTouch User Manual 94 Actuator Systems http www advancedactuators com ReliTouch User Manual 95 Actuator Systems http www advancedactuators com ReliTouch User
14. will not be able to unlock the ReliTouch RT 201 e If N No is chosen for a specific day of the week then the enrolled fingerprints and or PIN Code associated to the specific User ID will not be able unlock the ReliTouch RT 201 for that day of the week e Press E to save the selection and exit and then scroll to the next day of the week ReliTouch User Manual 75 Actuator Systems http www advancedactuators com e When setting for Saturday Sat is completed press E Message Save will display on the LCD e Press E to exit multiple times until the Bye message displays and the ReliTouch RT 201 LCD powers off ReliTouch User Manual 76 i Actuator Systems http www advancedactuators com Section 3 Unlocking the ReliTouch RT 201 3 1 Unlocking the ReliTouch RT 201 in 1 N Mode with an enrolled fingerprint 1 Press the button on the keypad of the outside unit 2 A single short beep will be heard and the fingerprint sensor will power on 3 After the fingerprint sensor flashes the second time rest an enrolled fingerprint on the sensor window to verify ReliTouch User Manual 77 W az http www advancedactuators com 4 If fingerprint verification was successful two short beeps will be heard the green LED will flash and the ReliTouch RT 201 will unlock and remain unlocked for approximately four seconds If verification of the
15. 3 Del FP and press M e Deleted message will display e You will be returned to menu option 3 Del FP ReliTouch User Manual 65 W Lan http www advancedactuators com NOTE Once deletion of fingerprints associated to the specific User ID is complete fingerprints can be re enrolled for the specific User ID follow step 6 above 10 To set up Timed Access for the Specific User ID scroll down to and highlight section 4 Access Time and press M Each specific USER ID has three TIME MODES that can be set up for them Administrators can edit each specific User IDs Timed Access at anytime e ANY TIME When this is chosen the specific User ID can unlock the door with their enrolled fingerprints or PIN Codes at any time The exception to this is if specific Timed Access is set up for the LOCK e INVALID This can also be called lock down mode for the specific User ID When this is enabled for the specific User ID the User will not be able to unlock the door with their enrolled fingerprints or PIN Codes until an Administrator re assigns them to ANYTIME or ACC TIME e ACC TIME This mode allows for specific User ID to have timed access to unlock the ReliTouch RT 201 with their enrolled fingerprints or PIN Codes during a specific date range days of the week and time frame within the days of the week Acc Time means Access Time ReliTouch User Manual 66 pS http www advancedactuators com NOTE
16. E meaning that the clock is 24 hours instead of 12 hours EX If itis 11 00 PM the clock should be set up as 23 00 00 ReliTouch User Manual 30 _ Actuator Systems http www advancedactuators com 9 Choose the correct hour by using the Up Down arrows until desired numeric hour is chosen and press M to save selection 23 2009 Thu 43 Save 10 Choose the correct minute by using the Up Down arrows until desired numeric minute is chosen and press M to save selection 11 Choose the correct second by using the Up Down arrows until desired numeric second is chosen and press M to save selection ReliTouch User Manual p 5 A5 http www advancedactuators com 12 Choose the correct day of the week by using the Up Down arrows until desired day of the week is chosen and press M to save selection 15 Press E to exit ReliTouch User Manual 32 i Actuator Systems http www advancedactuators com 1 3 Setting Fingerprint Sensitivity for the ReliTouch RT 201 NOTE Fingerprint sensitivity settings range from 1 to 9 Setting 1 is the most strict setting meaning that quality of fingerprint and placement of fingerprint need to be almost perfect Setting 9 is the least stringent setting in regards to fingerprint quality and placement IF YOU ARE HAVING RECOGNITION ISSUES WITH ACCEPTING FINGERPRINTS SET THIS SETTING TO 9 1 In the Lock setup menu scroll down to a
17. Manual 96 Actuator Systems http www advancedactuators com ReliTouch User Manual 97 Actuator Systems http www advancedactuators com ReliTouch User Manual 98 Actuator Systems http www advancedactuators com ReliTouch User Manual 99 Actuator Systems http www advancedactuators com ReliTouch User Manual 100 Actuator Systems http www advancedactuators com ReliTouch User Manual 101 Actuator Systems http www advancedactuators com ReliTouch User Manual 102
18. PREFACE gt Thank you for purchasing ReliTouch RT 201 biometric lock gt Please read the documentation carefully before installation amp use The manual details all installation procedures gt Manufacturer and or Distributors of the ReliTouch RT 201 will not be responsible for any damages caused by incorrect installation or mishandling of the lock Any such damages will void manufacturer s warranty Further information on the warranty terms and conditions can be found on page 85 of this manual Actuator Systems http www advancedactuators com Table of Contents Tableof Colill ll i i 4 54i4 45 455a5ss54455 405 4ae 0ol sa dak k da Ken AW dU WE WA WO eW e K KAN ReliTouch RT 201 Installation Guide 4 Secl li 1 E d S s ac n n 1y c a k s n W eeu We se kl r veb ea nk W eka P R de s k a vaka kk 4 Section 2 Required Tools ssssooooooooooooooeeeeeeee 5 Section 3 Pre installation ccccccccsssssssssssssssssssccccccccccccccsssssssssssssssssees 6 3 1 Mark and bore holes On the COOP cccssccccsssececcsseceeeeseceeeeneees 6 3 2 Setting Installing the latch and strike plate 8 3 3 Removing handles and re installing for Right Left handed CONE O 9 en nee ence nr ee no Coe eee 10 Second Mistallati i Lis ni uns lea
19. The Time Setting chosen created for the lock will override any specific Timed Access assigned for a specific User For example if ACC TIME is chosen for the lock and set to Mon Wed and Fri 9am to 5pm Users will only have access to unlock the door during the set days and times no matter what individual timed access was set for them However Administrators User ID 1 3 will always have access to unlock the ReliTouch RT 201 Choosing ANY TIME as the Access mode for the Specific User ID e Scroll to ANYTIME option and press M e Message Saved will display And you will be returned to menu option 2 Anytime e Press E to exit ReliTouch User Manual 67 i Actuator Systems http www advancedactuators com Choosing INVALID as the Access mode for the Specific User ID e Scroll to INVALID option and press M e Message Saved will display And you will be returned to menu option 1 Invalid e Press E to return to exit ReliTouch User Manual 68 i Actuator Systems http www advancedactuators com Choosing and setting up ACC TIME as the Timed Access mode for the Specific User ID e Scroll to ACC TIME option and press M e The From and To Date Range options display The format for the Date Range settings is MMDDYYYY from left to right e Use the up and down arrows to choose the appropriate MM DD amp YYYY in
20. at you cut out of the installation template on the door with a magic marker ReliTouch User Manual 7 Actuator N Systems http www advancedactuators com 5 Bore the two 3 8 holes into the door using a 3 8 drill bit making sure that the holes fully penetrate through the door 3 2 Setting Installing the latch and strike plate 1 The latch that is included with the ReliT ouch RT 201 is adjustable for doors that have 2 3 8 or 2 4 backsets Adjust the backset by sliding the spindle hole under the correct setting for your door 1 ReliTouch User Manual 8 Actuator W Systems http www advancedactuators com 2 Insert the latch into the hole in the edge of the door and screw into place making sure that the center of the latch s spindle hole is in the center of the drilled 2 1 8 hole ReliTouch User Manual 9 W ctuator System mee http www advancedactuators com 3 3 Removing handles and re installing for Right Left handed configuration 1 The ReliTouch RT 201 is a non handed lock meaning that it can be installed on either a right handed or left handed door 2 Use the following steps to install the handles e 2a Insert outside units handle onto the lock based on your right left handed configuration e 2b Turn the outside unit over and insert a long thin Phillips head screwdriver into the spindle hole V ReliTouch User Manual 10 Actuator Systems
21. each section When desired numeric value ReliTouch User Manual 69 Actuator Systems http www advancedactuators com is chosen for each section press M to move onto the next date value o Example Desired From date is January 15 2009 In the From section o Use the up and down arrows to enter 01 for January and press M o Use the up and down arrows to enter 15 for the fifteenth day of the month and press M ReliTouch User Manual 70 Actuator Systems http www advancedactuators com o Use the up and down arrows to enter 2009 for the Year and press M o Use the same steps for the To date e Once the Date Range is set up press E Message Save will display on the LCD Press M e Message Saved will display Press E to exit without saving ReliTouch User Manual 71 i Actuator ys Systems http www advancedactuators com Use the following steps to set up the Time Frame for the Specific User ID The format of the time setup is HH MM and is in MILITARY TIME meaning that the clock is 24 hours instead of 12 hours EX If the From time 11 00 PM the clock should be set up as 23 00 Choose the correct Fr From hour by using the Up Down arrows until desired numeric hour is chosen and press M to save selection Choose the correct Fr From minute by using the Up Down arr
22. eliTouch PCMU for programming and audit trail or the ReliTouch AT Software for audit trail Use the following steps to set up the Lock ID at the ReliTouch RT 201 1 In the Lock setup menu scroll down to and highlight option 5 Lock ID and press M 2 Use the up and down arrows to scroll to the desired lock ID and press M to save setting 3 Message Saved will display 4 Press E to exit ReliTouch User Manual 38 i Actuator Systems http www advancedactuators com 1 7 Deleting ALL Fingerprints in the ReliTouch RT 201 1 In the Lock setup menu scroll down to and highlight option 6 Clear FP amp PIN and press M 2 To delete all fingerprints highlight the Clear FP option and press M 3 Cleared will display indicating that all fingerprints have been deleted 4 Press E to exit ReliTouch User Manual 39 i Actuator Systems http www advancedactuators com 1 8 Deleting ALL PIN Codes in the ReliTouch RT 201 1 In the Lock setup menu scroll down to and highlight option 6 Clear FP amp PIN and press M 2 To delete all PIN Codes scroll down and highlight the Clear PIN option and press M 3 Cleared will display indicating that all PIN Codes have been deleted 4 Press E to exit ReliTouch User Manual 40 Actuator Systems http www advancedactuators com 1 9 Setting up Ti
23. f verification of the enrolled fingerprint was not successful on the first attempt the LED will flash red no beeps If this happens re position the enrolled fingerprint on the sensor The sensor will try two more times to verify the enrolled fingerprint If all three attempts fail the LED will flash three times and three short beeps will be heard Remove the enrolled finger and start over from the beginning of this section Also check to make sure that the fingerprint being used has been enrolled If the LED flashes red three times and three short beeps are heard after the specific User ID and button were entered this indicates that the matching mode is set to L N If LED flashes red once and one single beep is heard after a successful verification this indicates that User ID associated to the enrolled fingerprint is either outside of their Timed Access settings OR their User ID is set to INVALID OR the lock is set to INVALID ReliTouch User Manual 81 i Actuator Systems http www advancedactuators com 3 4 Unlocking the ReliTouch RT 201 in 1 1 Mode with a registered PIN Code 1 Enter the specific User ID on the keypad of the outside unit Press Enter the Registered PIN Code and Press 2 If PIN Code verification was successful two short beeps will be heard the green LED will flash and the ReliTouch RT 201 will unlock and remain unlocked for approximately four seconds If verification of the
24. he Outside Unit 1 Attach the rubber gasket to the back of the outdoor unit 2 Turn the outside unit over to make sure that the spindle hole is perfectly square and not angled ReliTouch User Manual 13 i Actuator Systems http www advancedactuators com 3 Feed the wire set underneath the latch 4 Align the two middle fixing posts with the two corresponding holes in the latch ReliTouch User Manual 14 i Actuator Systems http www advancedactuators com 5 Align two bottom fixing posts with two 3 8 holes that were drilled 6 Insert outside unit onto the door making sure that the two middle fixing posts fit into the two holes in the latch and the two bottom fixing posts fit perfectly into the two 3 8 holes ReliTouch User Manual 15 i Actuator Systems http www advancedactuators com 7 Outside unit should be completely flush on the face of the door ReliTouch User Manual 16 es System mee http www advancedactuators com 4 3 Installing the fixing plate The purpose of the fixing plate is to securely fasten the outside unit onto the door so installation of the inside unit will be easier requiring only one person 1 Place fixing plate over the 2 1 8 hole on the inside of the door 2 Align center hole of the fixing plate with the spindle hole of the latch 3 Be sure that large rounded half circle 1s facing down on the fixing plate wire se
25. he finger or thumb on the scanner gives the best image but the finger must not move during scanning Adjust Fingerprint Sensitivity settings per Section 1 3 ReliTouch User Manual 53 W ee http www advancedactuators com Moist fingers and thumbs give better images than dry ones If on cold dry days you have difficulty for example try moistening your finger or thumb with your breath or a little lotion Very dry dirty fingerprints with cracks going across them or scarred fingers thumbs are obviously not recommended since they will obscure the fingerprint Always wait until the fingerprint scanner turns on to place your finger thumb on the scanning window This is true for both fingerprint enrollment AND verification When trying to enroll or verify fingerprints in direct sunlight be sure to shade the sensor with your shadow so sunlight will not reflect off of the mirror in the sensor AED yan A Put the finger center on the r NA N M ON center of the scanner window Place finger flat on the i T window Good Bad Had Don t put finger on the edge and then move to the center Raise the finger then leave Da scanning window after ji he fingerprint scanning Don t drag the finger on the surface of the scanning window ReliTouch User Manual 54 i Actuator Systems http www advancedactuators com 2 1 Creating Editing amp Deleting User Access 1 Press M lock will disp
26. lay a welcome message display date and time display current lock ID display NO MASTER and display voltage remaining in the batteries e Ifan Administrator has already been added to the lock the Administrator will need to successfully verify their enrolled fingerprint OR registered PIN code use up and down arrows to choose after pressing M Once the RT 201 Administrator is successfully verified two short beeps will be heard and the LED will flash green twice ReliTouch User Manual 55 Actuator Systems http www advancedactuators com 3 In the ID field use the up and down arrows to scroll to the desired User ID and press M e Again User IDs 1 thru 3 are Administrator Master Users that will have access at any time to unlock the door or program the ReliTouch RT 201 Users 4 thru 1000 are General Users that have access to unlock the door at times set up by one of the Administrator Users and have no programming rights to the ReliTouch RT 201 ReliTouch User Manual 56 Actuator Systems http www advancedactuators com 5 Use the down arrow to scroll thru the following options 1 Add FP When this option is chosen fingerprints can be added for the specific User ID Lidi 2 Add PIN When this option is chosen a PIN Code can be created changed or deleted for the specific User ID 3 Del FP When this option is chosen the fingerprints associated to the specific
27. med Access for the ReliTouch RT 201 The ReliTouch RT 201 has three TIME MODES that may be chosen for the lock e ANY TIME When this is chosen the specific lock allows for all enrolled Users to have access to unlock the door The exception to this is if specific Timed Access is set up for individual Users e INVALID This can also be called lock down mode When this is enabled only Administrators for the specific lock will have access to unlock the door ReliTouch User Manual 41 W oon http www advancedactuators com e ACC TIME This mode allows for timed access to the lock to be created for a specific date range days of the week and time frame within the days of the week Acc Time means Access Time NOTE The Time Setting chosen created for the lock will override any specific Timed Access assigned for a specific User For example if ACC TIME is chosen for the lock and set to Mon Wed and Fri 9am to 5pm Users will only have access to unlock the door during the set days and times no matter what individual timed access was set for them However Administrators User ID 1 3 will always have access to unlock the ReliTouch RT 201 ReliTouch User Manual 42 i Actuator Systems http www advancedactuators com 1 10 Choosing ANY TIME as the Access mode for the ReliTouch RT 201 1 In the Lock setup menu scroll down to and highlight option 7 Access Time and press M jili 2
28. nd highlight option 2 Sensitivity and press M 2 Use the up and down arrows to scroll thru the sensitivity levels until the desired level is reached and press M to save setting ReliTouch User Manual 33 i Actuator W D http www advancedactuators com 3 Message Saved will display 4 Press E to exit 1 4 Setting the Matching Mode There are three choices for how the ReliTouch RT 201 will verify enrolled users for access to unlock the door e 1 1 When this is chosen all users enrolled at this lock must enter their User ID then verify their enrolled Fingerprint or PIN Code to successfully unlock the door e 1 N When this is chosen all users enrolled at this lock will only need to match their enrolled Fingerprint or PIN Code to successfully unlock the door e 1 amp N When this is chosen all enrolled users can use the 1 1 OR 1 N method to successfully unlock the door ReliTouch User Manual 34 i Actuator Systems http www advancedactuators com Use the following steps to set up the Matching Mode at the ReliTouch RT 201 1 In the Lock setup menu scroll down to and highlight option 3 Match Mode and press M 2 Use the up and down arrows to scroll thru the matching modes until the desired mode is reached and press M to save setting 4 Press E to exit ReliTouch User Manual 35 Actuator Systems http www advancedactuators
29. om e Use the up and down arrows to enter 15 for the fifteenth day of the month and press M e Use the up and down arrows to enter 2009 for the Year and press M e Use the same steps for the To date ReliTouch User Manual 47 Actuator Systems http www advancedactuators com 6 Once the Date Range is set up press E Message Save will display on the LCD 7 Press M Message Saved will display on the LCD OR press E to exit without saving ReliTouch User Manual 48 i Actuator Systems http www advancedactuators com The format of the time setup is HH MM and is in MILITARY TIME meaning that the clock is 24 hours instead of 12 hours EX If the From time 11 00 PM the clock should be set up as 23 00 Choose the correct From hour by using the Up Down arrows until desired numeric hour is chosen and press M to save selection Choose the correct From minute by using the Up Down arrows until desired numeric minute is chosen and press M to save selection ReliTouch User Manual 49 Actuator Systems http www advancedactuators com e Choose the correct To hour by using the Up Down arrows until desired numeric hour is chosen and press M to save selection e Choose the correct To minute by using the Up Down arrows until desired numeric minute is chosen and press M
30. on the LCD and 3N will not change to 3Y Repeat the steps above to try again ReliTouch User Manual 62 W D http www advancedactuators com e When all fingerprints have been successfully enrolled 1Y 2Y 3Y will display Press E to exit back to the specific User IDs menu options 7 To Add or Modify a PIN CODE associated to the specific User ID scroll down to and highlight section 2 Add PIN and press M e Using the numeric pad on the outside unit enter a 1 to 10 digit PIN Code for the specific User ID all User IDs can have both a PIN Code and or Fingerprints assigned to them and Press or to save it ReliTouch User Manual 63 i Actuator Systems http www advancedactuators com e PIN Saved message will display unless same PIN Code already exists for another User ID A short beep will be heard and you will be returned to Option 2 Add PIN automatically 9 To Delete a PIN CODE associated to the specific User ID highlight section 2 3 Pin and press M e Using the numeric pad on the outside unit press the button clears PIN Code ReliTouch User Manual 64 i Actuator Systems http www advancedactuators com e PIN Cleared message will display A short beep will be heard and you will be returned to Option 2 Add PIN automatically 10 To Delete FINGERPRINTS associated to the specific User ID scroll down to and highlight section
31. ows until desired numeric minute is chosen and press M to save selection ReliTouch User Manual 72 Actuator Systems http www advancedactuators com Choose the correct To hour by using the Up Down arrows until desired numeric hour is chosen and press M to save selection Choose the correct To minute by using the Up Down arrows until desired numeric minute is chosen and press M to save selection ReliTouch User Manual 73 zav http www advancedactuators com e Once the Time Frame is set up press E Message Save will display on the LCD Press M e Message Saved will display Press E to exit without saving Use the following steps to set up the Days of the Week access for the Specific User ID e Highlight Week Days and press M ReliTouch User Manual 74 i Actuator Systems http www advancedactuators com e Press M button to choose Y Yes OR N No for each day of the week that is highlighted e If Y Yes is chosen for a specific day of the week then the Specific User ID will have access to unlock the ReliTouch RT 201 with their enrolled fingerprints and or PIN Code on that day of the week during the Date Range and Time Frame that has already been set up Once the Date Range or Time Frame has expired the fingerprints and PIN Code associated to the Specific User ID
32. r any other menu options for that matter after an Administrator fingerprint has been enrolled then their fingerprint will need to be verified after pressing M to enter the menu options ReliTouch User Manual 27 i Actuator Systems http www advancedactuators com 1 2 Setting the Date and Time for the ReliTouch RT 201 Setting up the Date and Time of the ReliTouch RT 201 is critical when using the ReliTouch PCMU for programming and audit trail or the ReliTouch AT Software for audit trail 1 Press M lock will display a welcome message display default date and time display current lock ID display NO MASTER and display voltage remaining in the batteries ReliTouch User Manual 28 Actuator Systems http www advancedactuators com 3 Option 1 Date Time is highlighted Press M Ht 4 The format for the date setup is MM DD YYYY 5 Choose the correct month by using the Up Down arrows until desired numeric month is chosen and press M to save selection ReliTouch User Manual 29 W http www advancedactuators com 6 Choose the correct day of the month by using the Up Down arrows until desired numeric day of the month is chosen and press M to save selection 7 Choose the correct year by using the Up Down arrows until desired numeric year is chosen and press M to save selection 8 The format of the time setup is HH MM SS and is in MILITARY TIM
33. reen LED will flash and the ReliTouch RT 201 will unlock and remain unlocked for approximately four seconds If verification of the registered PIN Code was not successful the LED will flash three times three short beeps will be heard and the ReliTouch RT 201 will power off Start over from the beginning of this section Also check to make sure that the PIN Code being used has been registered AND make sure that the matching mode is set to I N If LED flashes red once and one single beep is heard after the PIN code was successfully entered this indicates that User ID associated to the enrolled fingerprint is either outside of their Timed Access settings OR their User ID is set to INVALID OR the lock is set to INVALID ReliTouch User Manual 79 Actuator W Systems http www advancedactuators com 3 3 Unlocking the ReliTouch RT 201 in 1 1 Mode with an enrolled fingerprint 1 Enter the specific User ID on the keypad of the outside unit followed by pressing the button The sensor will power on 2 After the fingerprint sensor flashes the second time rest the enrolled fingerprint associated to the User ID on the sensor window to verify 3 If fingerprint verification was successful a single short beep will be heard the green LED will flash and the ReliTouch RT 201 will unlock and remain unlocked for approximately four seconds ReliTouch User Manual 80 ip Sen http www advancedactuators com I
34. registered PIN Code was not successful the LED will flash three times three short beeps will be heard and the ReliTouch RT 201 will power off Start over from the beginning of this section Also check to make sure that the PIN Code being used has been registered AND make sure that the matching mode is set to I N If LED flashes red once and one single beep is heard after the PIN code was successfully entered this indicates that User ID associated to the enrolled fingerprint is either outside of their Timed Access settings OR their User ID is set to INVALID OR the lock is set to INVALID ReliTouch User Manual 82 Actuator Systems http www advancedactuators com 3 5 Unlocking the ReliTouch RT 201 with the override keys 1 Insert key into the keyhole 2 Turn the key in the RIGHT direction to horizontal level 90 degrees 3 Pull up on the handle ReliTouch User Manual 83 Actuator Systems http www advancedactuators com 4 Turn the key back in the opposite direction and pull key out of the keyhole ReliTouch User Manual 84 Actuator Systems http www advancedactuators com Support Information Contact the Actuator Systems ReliTouch dealer you purchased the lock from OR Contact us at support advancedactuators com or 1 800 408 7101 ext 102 for additional support All RMA s and Repair requests are handled on the support RMA page on the Actuator Systems website at h
35. s ayn y k e karan kana ken de keka kes NA N n a ka EKE MANA 12 4 1 Impact Alarm Information ii keke 12 4 2 Installing the Outside Unit cece keke 13 4 3 Installing the fixing plate 0 0 cecccccsssececeeseceeeeeceeeeeeeeseeeeeeees 17 4 4 Installing the Inside Un t keke 18 Section S Power OpPHONS sy i i 56445 45y4454o55 455544 ay k k aka w eda yey is 22 n Sa eenen iea bere BB BD zJRRHNH Mn xn 22 5 2 Hardwiring the ReliTouch RT 201 xsereeeekekekekeeee 23 ReliTouch RT 201 Operations Manual se se se 24 wee SECURITY WARNING TY cssscccsscecsscessscccsuscesescesancccnsacessescessaccouseseess 24 Definitions of Indication Beeps ssssseseceeeccccccccsssssesecccecoccoccosssossssssccceeo 24 Det nitions OF LED sicccssccssacedcavessoscdussccdscuces klan bi Renas y k seken seke s b nu n k k n 25 Sechon 1 Lock S L iyi 5 44454545444555505344355542440 0405044445234545 004049400850 iS 26 1 1 Programming buttons on the inside unit A E E E j j 26 1 2 Setting the Date and Time for the ReliTouch RT 201 28 1 3 Setting Fingerprint Sensitivity for the ReliTtouch RT 201 33 1 4 Setting the Matching MO0 kk eee keka 34 1 5 Setting the LOCK MOdWde Eiu kk kk kk k ke ea 36 1 6 Setting up the LOCK ID kk eke e 38 1
36. t goes thru large rounded half circle and that the two side screw holes are indented 4 Screw the fixing plate onto the door so it is secure DO NOT over tighten the screws ReliTouch User Manual Gy eater Systems http www advancedactuators com 4 4 Installing the Inside Unit 1 Insert spindle thru the spindle hole of the latch into the spindle hole of the outside unit You should be able to feel the spindle pop into the outside unit s spindle hole 2 Insert spring into inside unit s square hole VERY IMPORTANT ReliTouch User Manual 18 iN Actuator Systems http www advancedactuators com 3 Attach rubber gasket onto the inside unit 4 Plug the wire set making sure black marker is on top of the connector head the two black marks should be lined up into plug on the inside unit Be sure that wire set is fully plugged and seated well ReliTouch User Manual 19 Actuator Systems http www advancedactuators com 5 Stuff excess wires into the 2 1 8 hole 6 Install inside unit onto door making sure that the spring does not fall out when unit is placed upright and onto the spindle ReliTouch User Manual 20 i Actuator Systems http www advancedactuators com 7 Affix lock to the door with the three screws that match the thickness of the door per NOTE in beginning of Section 4 The longer screw is for the top fixing post and the two shorter screws are
37. ttps www advancedactuators com support submit rma ACTUATOR SYSTEMS LIMITED 2 YEAR WARRANTY COVERAGE IS AS FOLLOWS If your ReliTouch experiences any mechanical or electronic failure caused by defects in material or manufacturing workmanship during the 2 year warranty period Actuator Systems will repair or replace the unit at Actuator Systems expense including ground shipment expenses In addition during the first 30 days after purchase Actuator Systems offers a FREE hot swap of the ReliTouch with a new ReliTouch at Actuator Systems expense You must return your original ReliTouch lock within 14 days from the date you receive your replacement lock or you are liable for the full retail price of the replacement lock Hot swaps after the first 30 days are available for a fee Your returned ReliTouch must include all items that were originally included in the package or additional fee s will apply ReliTouch User Manual 85 Actuator Systems http www advancedactuators com Your limited warranty is voided if any of the following conditions are true 1 The ReliTouch is abused or misused a This includes scratches or other damage that can occur during installation 2 The ReliTouch is damaged or neglected during installation or use a This includes exposure of the inner portion of the lock the portion with the LCD screen to rain or snow The outdoor portion can be exposed and is designed for rugged exposure b Mounting

ReliTouch User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents