P2_PANTHER_user manual_ work basis_EN_03.indd
Contents
1. Dual apertures set level in a flat exterior wall Distances of dual apertures set level with each other in a flat wall are a 1 5m g 5 0m c 5 0m If g lt 5 m an intersection zone occurs making it necessary to maintain the total 8 m width of the zone and also increase the a values proportionally on both sides e g if g 4 0 m then a 2 0 m Dual apertures set level in a flat exterior wall Dual apertures set vertically 24 The minimum distances for double apertures set vertically in a flat exterior wall are a 0 5m b 1 0m c 5 0m a1 depending on x as follows x 25 0 m then a1 0 5 m x 24 0 m then a1 0 6 m x 2 3 0 m then a1 0 75 m x2 2 0 m then a1 1 0 m x 21 0 m then a1 1 2 m Dual apertures set vertically in a flat exterior wall e Important warning The examples cited for placing exhaust ducts can be used only in repairs or reconstructions of properties Other cases must be approached as set forth in Decree No 410 2003 of the Slovak Ministry of the Environment which amends and supplements Decree MoE SR No 706 2002 Coll on Air pollution sources on Emission limits on Technical requirements and general operating conditions on the List of toxic substances on the Classification of air pollution2. safety valve it is therefore recommended to install a bleeder that feeds into the sewerage system of the property After completing the installation of the gas piping into the boiler the gas tightness of the completed connection must be checked thoroughly Caution Do not under any circumstances manipulate the safety valve during the operation of the boiler The safety valve furthermore may not be used for releasing water from the boiler or the heating System The settling in the valve of detritus from the heating system is not covered by the warranty 8 12 Hooking up gas The PANTHER version of the boiler is designated for operation with natural gas with a rated pressure in the piping system of 2 kPa for which a heating value from 9 to 10 kWh m3 is most often specified The dimensions of the internal gas distribution 14 P2 PANTHER usemenual workbesis EN_0307 1 Prothem 8 13 Operating sketch of 25 KOV 10 1 tt ge 12 G WwW J 13 il 14 15 7 im 7277777 E m EA E JL gm EF m xc kb FS i T fere L TEL U FIT A B C D E Legend 1 Safety valve A CH outlet 2 Gas valve B HW outlet 3 HW exchanger C Gas inlet 4 Discharge valve D HWinlet 5 Burner E CH inlet 6 Ignition electrodes 7 NIC CH water intake temperature sensor 8 Combustion chamber 9 CH exchanger Exhaust gas c
3. the same as with pipes that vent into open areas Both components of the route external air and internal exhaust gas must safely feed into the relevant chimney duct but not protrude so deeply that they create blockages in the exhaust or air ducts TM 8 17 5 The C method KTV KTO Separate double piping and venting into different areas with different parameters mainly of pressure P2 PANTHER usemanual workbesis EN 0307 11Protnerm For venting exhaust and bringing in air for combustion separate piping may be used The separate piping may not be routed on opposing walls of the building XS 5 Attention Any duct crossing a wall that exceeds the ambient temperature by more than 60 C must be thermally insulated at the site of this crossing The insulation can be carried out using an appropriate insulating material with a thickness 2 10 mm and a thermal conductivity lt 0 04 W m K 8 17 6 The C method KTV KTO Using piping in cases where the air is drawn in from an open area and the exhaust vents into a shared chimney IL CR MN 6446440440004 PULL AA P2 PANTHER usemanud workbesis EN 0807 Prohem Air may in the same way be brought in from an open sp
4. In this case itis necessary to add pressure in the system committing water If the system pressure reaches 0 5 bar pressure stops flashing and also the symbol for a small amount of water in the system is not displayed if pressure increase above the value of 2 4 bar screen begins to flash the current value of the pressure In this P2 PANTHER usemanud workbasis EN 0807 Prohem case it is necessary to reduce water pressure in the heating system water withdrawal from the system If the system pressure falls below 2 4 bar the display again shows the current status of the boiler 8 3 User settings 8 3 1 The PANTHER boiler can work in various modes Heating mode press the MODE key once The display will portray the real time pressure in the system and the real time CH temperature along with the radiator icon The HW temperature setting is not displayed In this mode the boiler heats only CH water HW heating is locked out SUMMER mode press the MODE key twice The display will portray the HW temperature setting together with the water tap icon and the real time pressure in the system The real time CH temperature is not displayed In this mode the boiler responds only to requests for hot water the central heating is locked out VACATION mode press the MODE key three times The display will show only the real time pressure in the System The real time CH temperature and HW temperature setting together wi
5. Nae WET E Dimensions height width depth 740 1410 1330 P2 PANTHER usemanual workbasis EN 0307 11Protherm 35 s o e wma ees os gee vexmamtnemarconsumpin TE im ermal consumption JURI Gas pressure TJE oo T 2 08 0 77 Inlet pressure mbar HEN Maximum working pressure bar Minimum working pressure bar Recommended operating pressure E A o i pres i 36 P2 PANTHER usemanual workbasis EN 0307 11Protherm Quantity of HW drawn at AT 30 C i vin sees DS T p ae 9 9 EE GU GNE Dimensions height width depth 740 1 410 1330 P2 PANTHER usemanual workbasis EN 0307 11Protherm 37 El eel ea lum seereis ei teri censuron ass Minimum ter consumption w o Memumwemaupa fw 28 Minimum temaron w ce R ee OO Gas pressure Membrane dancin mm meme tw 9 mme e mmus jme 7 38 P2 PANTHER usemanual workbasis EN 0307 11Protherm Quantity of HW drawn at AT 30 C p ET momoa J Nae e 9 EE GU CNN Dimensions height width depth 740 1410 1330 P2 PANTHER usemanual workbasis EN 0307 11Protherm 39 ET WNT rron O 69e ee css ee 622 ime ws Gas pressure 2 05 0 82 Inlet pressure mbar HEN Maximum working pressure bar Minimum working pressure bar Recommended opera
6. HW inlet CH inlet 17 8 16 Operating sketch of 25 12 KTO 11 12 13 14 B 15 77777727 2 1 Legend A CH outlet 1 Safety valve B HW outlet 2 Gas valve C Gas inlet 3 Discharge valve D HWinlet 4 Burner E CH inlet 5 Ignition electrodes 6 NTC CH water intake temperature sensor 7 Combustion chamber 8 CH exchanger 9 Exhaust gas collector 10 Ventilator 11 Air manostat 12 NTC CH return water temperature sensor 13 Expansion tank 14 lonising electrode 15 Pump 16 CH pressure sensor 17 3 way motor valve 18 P2 PANTHER usemenual workbesis EN 0307 11Protnerm 8 17 Air and exhaust lines The type KOV and KOO is designed for combustion gases to be removed and discharged into a chimney through a chimney inlet with a minimum stabilised thrust of 2 Pa The boiler is connected to the chimney inlet by a flue of a diameter corresponding to the size of the boiler s gas exhaust outlet It is forbidden to place inside the combustion gases exhaust ducting any objects which impair the combustion gases flow e g various types of heat exchangers to utilise their residual heat The combustion gases exhaust ducting is not part of the boiler accessories Construction of the combustion gases exhaust ducting as well as that of the chimney must comply with relevant reguirements Compliance with the reguirements specified by these standards will prevent
7. Note The release valve is located on the right side of the boiler at the pump 8 10 Expansion vessel Before filling the CH system check the pressure in the expansion chamber The initial pressure in the expansion chamber should be greater by 0 2 bar than the static height of the water column of the heating circuit Water may then be released into the CH system Filling water pressure should be 0 2 0 3 bar higher than the pressure in the expansion chamber Filling pressure is controlled from the cold state by the gauge on the water side after bleeding The valve for topping up the pressure in the expansion chamber is on the right side Caution Confirm that the expansion chamber is sufficient for the given quantity 13 of water in the CH circuit see the project piping and gas meter must be adequate installation documentation to handle the other gas appliances of the user 8 11 Safety valve Gas lines in buildings must be installed in The safety valve is located the underside compliance with STN EN 1775 of the boiler on the left of the hydraulic block Draining from the safety valve Caution lt is recommended that the may lead if the maximum pressure in gas inlet into the boiler be tightened by the system is exceeded to the outflow fastening a union nut on the top face of of water or the escape of steam For the socket through the corresponding overflow that may emerge through the sealing see the Packing list
8. Sources and on Requirements for ensuring the dispersion of hazardous substances P2 PANTHER usemanual workbesis EN 0307 11Protherm 8 17 12 Safety measures The distance of flammable materials from the exhaust component of the separate piping must be enough to ensure that the temperature at the surface of these materials is no higher than 80 C Exhaust may not be vented in areas where a danger of explosion is present as set forth in STN 33 2320 thatare interior areas of a building lofts halls stairwells etc closeable i e passages or gateways etc that descend underground even if these remain open to the surroundings and free of obstructions e g tunnels underpasses etc These basic injunctions for venting exhaust must always take adequate account of where independent air intakes are sited Wall apertures for coaxial piping for drawing in air and venting exhaust are cut to the appropriate size approx 120 to 150 mm and sealed with building construction methods following the installation Non flammable materials with Degree A of flammability according to STN 73 0823 must be used for sealing e g masonry mortar plaster etc Openings in combustible walls or roofs must be made according to the first section of this part 8 18 Connecting the boiler to the electricity supply Hooking up the boiler to the mains voltage is done through a triple wire plug with a flexible cord The socket for
9. connecting the boiler to the electrical network must comply with STN 33 2000 4 46 It must always have the protective ground pin P2 PANTHER usemanud workbesis EN 0807 Prohem reliably connected with the PE or PEN wire a combination of green and yellow colours The boiler must always be connected through its main to the ground and must always be installed in a way that allows access to the socket and plug The use of a variety of adaptors extension cords etc is not permitted Caution The preparation of plugs and sockets as well as room regulator connections that extend into the interior electrical components of the boiler must under all circumstances be carried only by a person with electrotechnical qualifications as set forth in Decree No 50 1978 Coll In the same way servicing of the electrotechnical components may be carried out only by a person with the above mentioned professional qualifications Before servicing the electrotechnical elements the boiler must be disconnected from the current by pulling the mains lead from the socket The main body of the boiler is protected by a tube fuse T 2A 250 V which is located on the boiler control board For regulating the boiler from a room regulator only a regulator that has a no voltage input i e that does not send any external voltage into the boiler may be used Load carrying capacity of the regulator with a relay switch is 24V 0 1 A The room
10. o Pplk PljuSta 45 909 01 Skalica Tel 034 6966 101 fax 034 6966 111 Insert the bar code F2 ENIFER uar dock EN B
11. undesirable phenomena from occurring such as excessive cooling of the combustion gases penetration of dampness into brickwork and fluctuations in the chimney thrust and thus prevent undesirable effects on the boiler s functioning The boiler takes combustion air from the space in which it is installed Air must be supplied in sufficient guantity in accordance with applicable regulations Venting of exhaust and drawing in of combustion air for the KTV and KTO type is done only through designated pipes The level sections of the piping slope at a gradient sufficient to let the condensation drain towards an outside area or towards a receptacle designed to draw off condensation To achieve this the elbow joint may be gently bent away from the straight section The upright sections of the piping are always fitted with devices to draw off condensate The P2 PANTHER usemanud workbasis EN 0807 Prohem devices for drawing off the condensate are installed where possible close to the passage where the exhaust exits the boiler Breakdowns caused by leaking condensate are not covered by the boiler warranty 8 17 1 Methods of air and flue gas ducting according to STN EN 483 and permitted piping lengths If not described otherwise for the individual following methods of placing coaxial pipe routes and their drainages the piping lengths from connection at the boiler to the drainage can be set as in the following cases Note Eac
12. 1 2 bar 8 8 Admitting water into the heating circuit Bringing water into the heating system small quantities only can be done via the inlet valve on the boiler When filling the boiler the following conditions must be observed The water pressure on entry into the boiler must always be higher than the water pressure in the CH circuit Water is drawn into the boiler strictly in a cold state CH temperature in the boiler up to 30 C The recommended water pressure in the cold boiler up to 30 C is between 1 2 bar The pressure in the expansion tank is checked and if necessary adjusted to the correct value see technical parameters on end of this manual 8 9 Discharging water from the boiler The outlet valve is designated primarily for lowering the water pressure in the boiler during repairs Only a partial discharge of water from the boiler is possible through this outlet A complete draining of water from only the boiler or the heating circuit and repeat filling must be carried out at inlet outlet valves at appropriate locations in the heating circuit P2 PANTHER usemanud workbesis EN 0807 Prohem Discharging and filling of water into the heating circuit and the subsequent operations air venting regulating the expansion tank are not covered by the boiler warranty If the HW in the boiler and piping is threatened with freezing appropriate measures must be taken to avoid this entirely
13. 14 Contact your sales service centre If gas leaks there is a failure in supply or if you suspect the same shut down the boiler and gas intake and immediately contact the gas company or service centre Available system pressure mbar Flow through the heating system I h oU 31 16 Technical parameters Gas Gas category HBP Ee re 00 FEE 9m Maximum thermal consumption KW 32 5 Maximum thermal output 29 6 Minimum thermal output kw 10 4 Emme LL BOE LS vs em oe nei fon 18 Gas pressure L epum fe 5 mened fem e F rre L Manman wonna ges ber Minimum woking presse ber Recommended operating pesswe ber Pewewwenne er EEN EN Marmur pressurer ge geseen ber Moxmum pressure Er Minimum presse er 32 P2 PANTHER usermanual workbasis EN 0307 11Protherm Quantity of HW drawn at AT 30 C ET TT Nae DT od WET EE EE Dimensions height width depth 807 450 360 P2 PANTHER usemanual workbasis EN 0307 11Protherm 33 ET N WENT EN wma ees os gee vexmamtnemarconsumpin TE im ermal consumption JURI Gas pressure TJE oo T 2 08 0 77 Inlet pressure mbar HEN Maximum working pressure bar Minimum working pressure bar Recommended operating pressure E A o i pres TT Er T f 34 P2 PANTHER usemanual workbasis EN 0307 11Protherm Quantity of HW drawn at AT 30 C T Fa
14. 8 4 Regulation of the boiler erre nett 10 8 5 Boiler connection parameters ese ee Re ee ee Re ee Re ee ee 11 8 6 Connecting the boiler to the CH HW and gas piping 12 8 7 Operating pressure in the heating circuit es ee se ee 13 8 8 Admitting water into the heating circuit sees 13 8 9 Discharging water from the bole Mn aaa aaa aaa nene even e zene T9 8 10 Expansion tank sees ii eren EE Exe EE Ee De traen rd feast 13 8 41 Safety EE ME AR EI AR ER red 14 8 12 HOOKING UP gas AE EE OE OE RE EE ed 14 8 13 Operating sketch of 25 KOV eiecti 15 8 14 Operating sketch of 30 KTV and 25 KTV sse 16 8 15 Operating sketch of 25 12 KOO aaa ee ee ee AR ee Re ee ee 17 CONTENTS 8 16 Operating sketch of 25 12 KTO ana aaa ee ee ek ee ee Ke ee ke ee 18 8 17 Air and exhaust lines ics eiie iine EED ENE EG oon 19 8 18 Connecting the boiler to the electricity supply 25 8 19 Boiler wiring diagram iii ee ee ee ee RA Re Re ee RR ee ee evente 27 NEED HELP 9 10 11 12 13 14 15 16 Troublesliootlrig iint rr OE RE 28 Safety regulationS ee ee ee EEN DEN LEDER 30 Servicing and maintenance of the boiler o oo ee ee ke ee Re ee 30 111 Gleaning si EE de dero tei utei 30 11 2 Reg lat serviClng uenerit EE EE N 30 11 3 Replacement parts ENE KEN EE GE Ge GR GEGEE BE ON GEED GR E
15. UNE E 03 30 KTV 22 P2 PANTHER usemanual workbesis EN_0307 1 Prothem diameter 60 100 80 125 80 80 41 41 41 41 41 41 1 4 60 100 C32 25 KTV 80 125 25 KTO B2 fe Diffuser diameter T E E o o o ole jole ala ala 0 5 0 5 0 5 0 5 Note Each additional 90 elbow dicrease the total length about 1m Each additional 45 elbow dicrease the total length about 0 5m 8 17 11 Examples of flue duct placements according to Appendix No 7 of the Government Regulations of the SR No 92 1996 Coll Independent apertures in a flat wall Independent aperture creates a zone from the axis of the aperture of a width a 0 5 m radius b 1 0 m and height c 5 0 m Sketch of the zone created by an independent aperture of an exhaust stack P2 PANTHER usemanud workbesis EN 0807 Prohem Ma ba If the axis of the aperture is at a distance d gt 0 3 m below the upper part of the window frame the zone may not extend to the window surface At distances d lt 0 3 m the protective zone of radius b may extend to the upper part of the window 23 Sketch of the zone from the axis of the aperture of the exhaust stack sited close to the upper part of the window d gt 0 3m
16. ace or a space well supplied with air and exhaust extracted into a common chimney or again into a space with common venting of exhaust gases The special case of B also belongs in this category See following text 8 17 7 The B method 25 KTV 25 KTO Extraction of exhaust also in separate piping into an open area and intake of combustion air from an internal space in the building in close proximity to the boiler in coaxial piping with the perforation of its outer part When drawing in air for combustion from internal areas of the building a sufficient quantity of that air must be ensured No other appliance may be connected to the exhaust duct whether chimney or pipe and when drawing in air at least 1 2 m3 of air hour per kW of boiler output must be available 21 8 17 8 The B method only for 8 17 9 Piping gradient 30KTV The layout of the piping must permit a down gradient of the exhaust piping towards the boiler at a nominal gradient of 3 percent A device for drawing off condensate must be placed on the piping as close as possible to the boiler 8 17 10 Lengths of fumes Fume Diffuser Boiler Comment diameter diameter 36 0 5 3 with elbow 90 E 3 no eibow a fe 80 80 EIE 1 343 with elbow 90 80 80 ET s est Rows Je Je Je este SEE ee ees aoveo esos ins winetens TI mm fo fo e winetow so 0 3 with elbow 90 H
17. boiler scale on these disturbances or on induced disturbances e g silting up of the exchanger pump breakdowns are not covered by the boiler warranty The distance from flammable materials e g PVC fibreboard polyurethane synthetic fibres rubber etc must be P2 PANTHER usemenual workbesis EN_0307 1 Prothem sufficient to keep the surface temperature of these materials below 80 C The minimum working unhindered space in close proximity to the boiler must be such that the boiler can be worked with easily and safely with bare hands and with the usual hand tools we recommend a minimum distance of 300 mm from up and under 10 mm from side and a minimum of 600 mm in front of the boiler CH heating HW hot water The PANTHER boiler models KTV and KOV supplies both central heating and hot water for the home or only for central heating models KTO and KOO Non condensing boiler with exhaust vented to a chimney Models KOV and KOO must be fitted to a ventilation system chimney The boiler comes equipped with a safety device that shuts off the gas feed if the chimney becomes blocked Non condensing boiler with forced extraction of exhaust The KTV and KTO models are gas models fitted with a ventilation system for the intake of air and the venting of exhaust Thanks to this ventilation system the heater can be installed in any space If the ventilator fails or if the chimney becomes blocked the press
18. e boiler control panel is one way to guard against exceeding the maximum allowed temperatures into the heating system floor heating Despite this we recommend placing into the heating system a supplementary safety armature that will guard against a harmful increase in temperature Caution The room regulator and external sensor may be connected by authorized service personnel only P2 PANTHER usemanual workbesis EN 0307 11Protherm 8 5 Boiler connection parameters 8 5 1 Panther 30 KTV 4 110 9 4 65 4 116 Dr 65 Dig 94 pi d 27 amp 208 TS j 181 x ed Qo SPR P2 PANTHER usemanual workbasis EN 0307 11Protherm 8 5 2 Panther 25 12 KOO 25 KOV od D 479 7 y b 8 5 3 Panther 25 KTV 25 KTO 11 82 65 116 160 8 5 4 12 amp EI o Qe 0 Q9 6 O So O e Ka eo e e i 1 205 Panther 12 KTO 8 6 Connecting the boiler to the CH HW and gas piping The boiler connection terminals may not be placed under undue pressure from the piping system for the CH circu
19. e neo cie 30 rejette 30 Converting to different fuel ee Re ee em 31 Contact your sales service centre aaa ee ee ke ee ee ee ke ee ee ee ke ee ee 31 Available system pressure ee ee ee ee meme 31 Technical parameters cea tre ere Ree eR bx i e RR RR Rd 32 STUDY THIS MANUAL CAREFULLY 1 Read me 1 1 Welcome This manual is part of the eguipment and following installation it must be provided to the user in compliance with valid regulations Study the handbook carefully to ensure a safe installation safe use and proper service We are not responsible for any damage resulting from failure to follow the instructions presented in this handbook 1 2 User s quick start manual We have prepared this User s manual to help you start to use your equipment right away It is assumed in this manual that the equipment has been installed and commissioned by a qualified technician Study closely the Safety and Warranty chapters which contain important safety information Keys for setting the HW temperature RESET key Display Main switch Keys for setting the CH temperature MODE key Oouahwh P2 PANTHER usemanud workbesis EN 0807 Prohem 2 Commissioning the boiler 2 1 Description of the device PANTHER boilers are compatible with the usual types of hot water circuits and radiators A network of service providers who meet the mentioned reduirements work under contract to the manufacturer to commi
20. h time an extra 90 elbow is needed or 2 at 45 the length L must be reduced by 1m Caution If the lengths described for individual types are exceeded the exhaust diffuser orifice must be removed from the ventilator drain The following methods of air intake and exhaust venting are recommended for the boiler 8 17 2 The C method KTV KTO Level routes and level venting into an open area An example of a level coaxial pipe route version C complies with STN EN 483 19 8 17 3 The C method KTV KTO Vertical routes and vertical venting into an open space An example of a vertical coaxial pipe route version C complies with STN EN 483 UUO PELE UL AAAAAAAAAAAAA Umm Mm Mm Mm mM Mm fm 8 17 4 The C method KTV KTO Connecting to a double shared chimney Double piping from independent boilers independent routes can feed into shared chimneys the transport capacity of the chimney is judged according to the 20 manufacturer s data on the chimney If the pipes are set into the chimney in two directions and vertically aligned there must be a vertical separation between the outlets of at least 0 45 m Where two outlets vent towards each other they must be separated by a minimum vertical distance of 0 6 m The exhaust piping into the shared double chimney never has terminal elements
21. it the HW circuit or from the gas intake This assumes a precise observance of the dimensions of the endings of all connecting pipes with regard to height as well as distance from walls and separation distances of the interconnected individual intakes and outlets The heating system circuit should be connected to the boiler in such a way that during repairs to the boiler the heating water need be released only from the boiler During reconstructions in adverse building arrangements and so on the boiler may be connected to the CH heating system the HW system and the gas inlet with flexible elements hoses but only those designated for this purpose If flexible elements are used these should be as short as possible and must be protected from mechanical and chemical stresses and damages It must also be ensured that before the end of their life cycle or reliability in maintaining their parameters according to their manufacturers data they are always replaced by new ones Note The boiler includes filter which is situated below the HW flow sensor You have to take out the HW flow sensor with filter to clean up the filter P2 PANTHER usamanual workbesis EN 0307 11Protnerm 8 7 Operating pressure in the heating Circuit The heating system measured at the boiler must be filled to a hydraulic pressure of at least 1 bar corresponding to a hydrostatic height of water of 10 m The recommended pressure range is between
22. led 7 Packing list Legend Boiler Draw bar Exhaust gas diffuser only for 12 KTO Sealing Template Butt end of water intake Butt end of outlet valve Service manual Warranty o o 1o00 0N2 Exhaust gas diffuser is mounted in boiler for 25 and 30 kW 8 P2 PANTHER usemenual workbesis EN 0307 11Protnerm HOW TO USE THE BOILER 8 Using the equipment 8 1 Overview 8 2 Turning on and off The boiler is turned on and off at the main switch which is located on the control panel of the boiler 8 2 1 Display icons When you turn on the boiler the display shows the current status of the boiler if the boiler is not lit do not heat HW eighter CH so called stand by mode the display shows the current water pressure in the heating system the current CH temperature and set HW temperature with the symbols tap at HW and radiator at CH during the CH heating radiator symbol flashes on the screen is displayed current CH temperature and real time pressure in the system during the HW heating screen in the upper right corner displays the flame symbol and flashes tap symbol on the Screen shows real time pressure in the System current CH temperature and set HW temperature if pressure drop in the system below 0 5 bar starts flashing on the display symbol for the lack of water in the System crossed drop together with the current value of pressure
23. ler wiring diagram 5 El a aa jy SE E EE EE X16 sje e al E E aaja Elle X16 X17 Tank AQUASTAT LN NTC 2 OF TNL 230 VAC Legend Regulation connector Exalink connector NTC solar connector Alternative 24V connection User interface Hydraulic connector Gas valve Ventilator Fuse 10 230 V connection 11 Pump 12 Electrodes 13 NTC CH water intake temperature sensor 14 NTC CH return water temperature sensor o o 1000 0 N22 P2 PANTHER usemanual workbasis EN 0307 11Protherm 15 Thermal fuse 16 NTC CH flow sensor 17 NTC HW flow sensor 18 3 way motor
24. ment Becareful not to allow children to play with the boiler Do not plug or obstruct the ventilation system Some home improvements may significantly affect the functioning of the boiler Before carrying out any such intervention you must consult with the installer Do not site the equipment in excessive dampness Do not use and do not store explosive or flammable materials e g gasoline petrol aerosols thinners chlorine based cleaning agents paints glues etc in the same space as the boiler Under certain conditions these materials may be corrosive Do not touch the equipment surfaces e g the ventilation pipes hydraulic connectors and so on even after the boiler has been turned off as these surfaces may be hot Touching these surfaces may lead to burns or scalding P2 PANTHER usemenual workbesis EN_0307 1 Prothem Be prudent when using the hot water tap Water coming out of this tap may be scalding This equipment contains metal parts components In working with it and in cleaning it particularly its corners you must be careful f water leaks from the unit you must immediately turn off the cold water intake and the leak must be repaired by a qualified technician Donotstore any objects on top of the equipment 5 Warranty Obligations 5 1 Warranty details PROTHERM s Panther boiler is covered by warranty as set out by the Warranty Service log and other conditi
25. move house you must leave this manual near the device in order to allow the new owners to find it To ensure safe and efficient use of your boiler study the instructions and observe them carefully 5 We bear no responsibility for damages resulting from failure to observe the instructions 3 2 Explanation of symbols DANGER Risk of injury DANGER Risk of electric shock CAUTION Risk of damage to the eguipment or its edge parts gt P IMPORTANT Useful information E 4 Safety regulations 4 1 What to do if you smell gas If you smell gas Do not search for the leak with an open flame Do not turn on any electrical switches telephones or any other devices that could spark an explosion Immediately open all windows and doors to ventilate the area Shut off the flow of gas at the safety valve Alert all other persons in the building Call from outside from your house the emergency assistance services of your gas supplier 4 2 Safety regulations The following regulations and safety instructions must be observed Never tamper with the safety devices Do not modify the equipment or its immediate surroundings as this could affect the safe use of the boiler Do not under any circumstances destroy or remove the sealing from any of the parts Never carry out alone any maintenance or repairs to the equipment Only qualified technicians may work with the equip
26. ollector 11 Combustion thermostat NTC CH return water temperature sensor Expansion tank lonising electrode Pump CH pressure sensor 3 way motor valve HW flow sensor HW filter Inlet valve P2 PANTHER usemanud workbesis EN 0807 Prohem Ma ee 20 15 8 14 Operating sketch of 30 KTV and 25 KTV Legend A CH outlet 1 Safety valve B HW outlet 2 Gas valve C Gas inlet 3 HW exchanger D HWinlet 4 Discharge valve E ChHinlet 5 Burner 6 Ignition electrodes 7 NTC CH water intake temperature sensor 8 Combustion chamber 9 CHexchanger 10 Exhaust gas collector 11 Ventilator 12 Air manostat 13 NTC CH return water temperature sensor 14 Expansion tank 15 lonising electrode 16 Pump 17 CH pressure sensor 18 3 way motor valve 19 HW flow sensor 20 HW filter 21 Inlet valve 16 P2 PANTHER usemenual workbesis EN 0307 11Protnerm 8 15 Operating sketch of 25 12 KOO 9 P d Legend Safety valve Gas valve Discharge valve Burner Ignition electrodes NTC CH water intake temperature sensor 7 Combustion chamber 8 CH exchanger 9 Exhaust gas collector 10 Combustion thermostat 11 NTC CH return water temperature sensor 12 Expansion tank 13 lonising electrode 14 Pump 15 CH pressure sensor 16 3 way motor valve ouahwh P2 PANTHER usemanud workbasis EN 0807 Prohem moou CH outlet HW outlet Gas inlet
27. ons listed in the service and installation manuals 5 2 Using the device Obligations of the manufacturer The above specified warranty is valid if The equipment was installed by a qualified technician in accordance with the installation guidelines The equipment is used for domestic purposes and in compliance with the operation and maintenance instructions of the manufacturer All servicing maintenance repairs dismantling of or working with the equipment during the warranty period is carried out by a qualified technician only Repairs or replacement of parts during the warranty period do not extend that period P2 PANTHER usemanud workbesis EN 0807 Prohem The manufacturer bears no responsibility whatsoever for any damages resulting from Any type of damage arising from incorrect or incomplete installation inadequate servicing or incorrect hook up of gas or water Any type of damage to a system to which the equipment is connected Any type of damage caused by incorrect protection against freezing Any type of damage or faulty set up caused by changes of character or pressure of gas or water or changes in electric voltage For further information please study the Conditions This equipment may be installed only in countries listed in the descriptive plaque 6 Recycling Most of the boiler is comprised of recyclable materials The equipment packaging must be properly recyc
28. protherm gt Panther User manual 30 KTV v 19 25 KTV v 19 25 KOV v 19 25 12 KTO v 19 25 12 KOO v 19 me Wall hang non condensing boiler mu Power 10 4 29 6 3 4 12 6 kW mu Flow heating HW external HW tank EN C CONTENTS STUDY THIS MANUAL CAREFULLY 1 Read fte 3 1 1 Welcome se EE teure 3 1 2 User s quick start manual isisisi sissien aea arraiais 3 2 Commissioning the boiler 3 2 4 Description of the device see ee ee Re eseve vene teze zere 3 2 2 Commissioning the boiler ii ee ee Re ee ee Re Re eee vene 5 2 3 Shutting down the boiler s 5 3 Manufacturer s documentatiON ee ee Re Re RA ee ee ene 5 3 1 Storing of documents sees ee ee ee ee ee ee Re ee ee enne 5 3 2 Explanation of symbols se ee ee ee ee siii zere ee ee ee ee ee ede ee 6 4 Safety regulations EE EE n ee 6 4 1 What to do if you smell gas ss 6 42 Safetyregulations iei rettet me Ee oe me teuren oes 6 5 Warranty Obligations ER EE hd de 7 5 1 Wartranty delalls N OR ere EE EE 7 5 2 Using the device Obligations of the manufacturer 7 yr 7 7 Packing list OE 8 HOW TO USE THE BOILER 8 Using thie eguiptmeri s sn eet tete ted e eere ee eet peu de 9 8 1 eI I KAK 9 982 TUBMING omand Of irr terere E enean ee Ee Ee 9 8 3 UET Eni fec EE 9
29. regulator must be connected to the boiler with a two wire plug The recommended cross section for the room regulator connection copper lead is 1 5 mm Leads for connecting the room regulator may not be coaxial vvith the mains voltage leads The terminal for hooking up the room regulator with the relay switch is supplied 25 by the manufacturer with a connector and is located in the frame of the boiler control panel Room regulators may be connected to the PANTHER boiler via eBUS Communication For this type of equipment however we recommend installing only Protherm Thermolink B Thermolink P or Thermolink RC regulators Only in this way can the manufacturer guarantee the optimal functioning of the boiler The room regulator leads are connected to the terminal board of the boiler By means of the above mentioned regulators the isothermal regulation function can be activated All settings for isothermal curves are carried out with the aid of the room regulator Note To activate the isothermal regulation the external temperature sensor must be installed The external sensor lead is connected to the terminal board of the boiler The external sensor is placed on the coldest wall of the property most often the northern wall Caution The room regulator lead and the external sensor may not be coaxial with power cables 230 V current etc 26 P2 PANTHER usemenual workbesis EN 0307 11Protnerm 8 19 Boi
30. ssion the boilers and to provide warranty and after warranty service The boiler as well as all its optional accessories complies with the reguirements of European Directive 90 396 EEC on gas fuelled appliances and European Directive 92 42 EEC on efficiency the European Directive 2006 95 EC on electrical means of operation for use in certain voltage ranges and the European Directive 89 336 EEC on electromagnetic compatibility The appliance is also approved according to the European norms EN 677 EN 625 EN 60335 01 EN 50165 EN 55014 EN 61000 3 2 and EN 61000 3 3 In order to operate and handle the boiler in accordance with the purpose for which itis designed in actual conditions of use hereafter referred to only as use it is necessary to abide also by additional conditions the most essential of which i e those which must not be omitted are found in the following regulatory documents in the design area STN 06 0310 and STN 06 0830 in the fire safety area STN 92 0300 for installation and fitting and repairs STN EN 1755 or STN 38 6460 as applicable STN 38 6462 Decree no 48 1982 Coll as amended by the later prescriptions and the binding occupational health regulations in time of running and operation STN 38 6405 in the area of discharge of combustion gases and air inflow STN EN 483 company material catalogue of dual piping for discharge of combustion gases and inflow of comb
31. supply to the boiler in ways other than by merely turning off the boiler at the main switch e g by pulling the boiler plug from the electrical Socket Always shut down the boiler when flammable or explosive vapours are detected even temporarily in the areas from which the boiler draws in air for combustion e g from oils for mixing paints the spreading and spraying of molten materials gas leaks etc P2 PANTHER usemenual workbesis EN_0307 1 Prothem f water must be discharged from the boiler or from the circuit it must not be dangerously hot f water leaks from the boiler exchanger or if the exchanger fills with ice do not attempt to start the boiler until normal conditions for boiler operation are restored 13 Converting to different fuel The Panther boilers are in their basic versions designed to use natural gas as fuel The modifications required to switch to a different fuel must be carried out by an authorised technician with a valid manufacturer s certificate 15 Available system pressure Legend 1 Pump at setting 1 by pass at factory setting 2 Pump at setting 2 by pass at factory setting 3 Pump at setting 1 by pass closed 4 Pump at setting 2 by pass closed P2 PANTHER usemanud workbesis EN 0807 Prohem For conversion to propane use the conversion kit for switching from natural gas to propane gas The kit contains all necessary parts and instructions on how to perform the conversion
32. tected following pump start Thermal fuse failure in primary exchanger Error in SHE entry sensor Error in charger pump Error in anode tester Not connected to APC module Error in APC module sensor When error codes displayed press RESET key If following this measure the equipment still does not work contact a qualified technician 10 Safety regulations 11 Servicing and maintenance of the boiler 11 1 Cleaning The boiler cover may be cleaned with a gentle liquid cleaner and damp cloth then wiped with a dry cloth Turn off the device before cleaning Do not use abrasive cleaners i or solvents as these may harm the paintwork 11 2 Regular servicing Regular servicing is very important in ex tending the lifecycle and safe and efficient use of your device Incorrect or inappropriate servicing may negatively impact the safe operation of the equipment and may result in injury 30 VVe recommend annual servicing of the equipment Always call in a qualified technician 11 3 Replacement parts To ensure safe operation and a lengthy lifecycle for the product you must use only original parts from the manufacturer 12 Regulations In practice there may arise situations in which you must take the following unavoidable measures Protect against even the accidental starting up of the boiler during inspection and work on the exhaust gas gas and water piping by shutting off the electricity
33. th the corresponding icons are not displayed In this mode both hot water and the central heating are locked out All the protective functions of the boiler are active Choice of heating mode 8 3 2 Setting the hot water temperature Press the or key and the HW value will begin to flash Pressing the or keys sets the desired HW temperature anywhere in the range of 38 60 C at one degree increments 8 3 3 Setting the temperature of the central heating water Press the or key followed by the MODE key and the CH value will begin to flash Pressing the or keys sets the desired CH temperature anywhere in the range of 38 80 C also at one degree increments 8 4 Regulation of the boiler 8 4 1 Operating the boiler without a room regulator In this mode the boiler will maintain the chosen CH temperature A room regulator is not connected connection terminals have to be interconnected supplied by the manufacturer Set up Press the main On Off switch Setthe desired CH temperature on the control panel 8 4 2 Operating the boiler with a room regulator If a room regulator is used the CH temperature must be restricted at the boiler control panel to the maximum recommended for your heating system to avoid damage to your system and which can also cover the thermal losses of the property at low outside temperatures Heating of the central heating water can then be managed b
34. ting pressure E o Ms 1 N i pres Er 40 P2 PANTHER usemanual workbasis EN 0307 11Protherm Quantity of HW drawn at AT 30 C Vin fo sees DS ca ET momoa J Nae e 9 EE GU GENE Dimensions height width depth 740 1410 1330 P2 PANTHER usemanual workbasis EN 0307 11Protherm 41 s N WETEN wma ees os gewe Gas pressure e w T N 0 91 0 36 Inlet pressure mbar ef Maximum working pressure bar Minimum working pressure bar Recommended operating pressure E o ies S 1 N i pres Er 42 P2 PANTHER usemanual workbasis EN 0307 11Protherm Quantity of HW drawn at AT 30 C min fo pronare aq Je T Fa ETE INN e Nae DT od 9 ee Dimensions height width depth 740 1410 1 330 P2_PANTHER_usermanual_workbasis_EN_0307 11 Prothem 43 s N WNT EN EEN WE 6965s ee css cnr 622 ime a scene Gas pressure e B on T 0 91 0 36 Inlet pressure mbar ef o Maximum working pressure bar Minimum working pressure bar Recommended operating pressure E o Mies S 1 N i pres Er 44 P2 PANTHER usemanual workbasis EN 0307 11Protherm Quantity of HW drawn at AT 30 C min sees DS Fa ET TT TJ Nae DT od 9 ee Dimensions height width depth 740 1410 1330 P2 PANTHER usemanual workbasis EN 0307 11Protherm 45 www protherm eu Protherm spol s r
35. ure switch shuts down the heater The boiler must be installed and commissioned by a qualified technician This ensures proper installation and operation in compliance with valid norms If any maintenance repair or adjustments concerning the gas are needed a qualified technician must be called P2 PANTHER usemanud workbesis EN 0807 Prohem PROTHERM has developed tailor made accessories that will help you use your heater with maximum efficiency 2 2 Commissioning the boiler Installation of the boiler and its first start up must be carried out by authorised service personnel only If you wish to start the boiler after it has been commissioned ensure that Itis hooked up to the electricity supply Allthe shut offs and valves CH HW gas under the boiler are open The CH pressure is within the recommended range of 1 2 bar 2 3 Shutting down the boiler Turn off the master switch If the boiler is to be shut down for an extended time close all the valves CH HW gas underneath it The shut down must take into account the water temperature in the boiler and the outside temperature in the given season If there is a danger of frost drain all water from the boiler the heating system and the hot water piping see the paragraph 8 9 on page 12 3 Manufacturer s documentation 3 4 Storing of documents This manual must be stored near the equipment to allow it to be accessed when needed If you should
36. ustion air designated for type C gas appliances i e in closed TURBO version The boiler is designated for operation within the normal AAS AB5 environment in compliance with STN 33 2000 3 and STN 33 2000 5 51 i e a temperature range of 5 40 C temperature dependent humidity to a max of 85 PANTHER boilers are suitable for the conditions of zones 1 2 and 3 in rooms with a bath or shower and in washing areas as set out in STN 33 2000 7 701 they may not be installed in zone 0 Fig 8 Before installation in the areas mentioned protection against electric shocks must be provided for according to the same norms The boiler complies with Ministry of Health Decree No 13 1977 Coll i e on noise for installation in residential and public areas The boilers are built to operate with heating water in compliance with STN 07 7401 Above all the water must never be acidic i e its pH must be higher than 7 and it should have minimal carbonate hardness The requirements regarding the characteristics of domestic water are set out in STN 83 0616 potable water STN 75 7111 With regards to water with total material concentrations of calcium and magnesium greater than 1 8 mmol l further non chemical measures against scale deposits e g operation of magnetic water treatments in combination with settling equipment are advisable Silting up of the boiler with contaminants from the heating system or the settling of
37. valve 19 CH pressure sensor The connector X16 is used only in the system versions without DHW heating of the Panther boilers KTO and KOO It is using for DHW sensor connection to external DHW tank 27 NEED HELP The external sensor is placed on the coldest wall of the property most often the northern wall When displaying an error code a telephone icon and the letter F This section contains all possible error will flash on the display together with the codes together with the appropriate relevant error code solutions that the USER MAY carry out to restore the boiler to operation corrective measures Other error codes MUST be dealt with by a gualified technician 9 Troubleshooting During the normal course of operation of the device the ten most recent error alarms can be displayed by simultaneously pressing for seven seconds both keys for setting the CH temperature Short circuit in NTC CH sensor 28 P2 PANTHER usemanual workbesis EN_0307 1 Prothem Anti freeze protection valve is active Pressure sensor is not on Pressure sensor is not off when the ventilator is not running Fe rovemwinesdnges TI ms lesse sor O OO N Qer qas vesa TT res Jerorimi ete Flame signal from ASIC is unreliable Detected flame input signal is outside range 0 or 5V P2 PANTHER usemanual workbasis EN 0307 1t Proiherm 29 Permanent failure CH pressure sensor No rise in pressure de
38. y the regulator which will permit only that maximum CH temperature you have set at the control panel Note In spaces with a regulator there should be no thermostatic valves on the radiators Caution The manufacturer assumes no responsibility for damages resulting 10 from faulty setting of the boiler or room regulator 8 4 3 On OFF regulator The boiler will maintain the selected CH temperature Boiler operation is interrupted turned on and off according to the internal temperature in the room in which the room regulator is located 8 4 4 Regulator with output modulation function selected The room regulator continuously regulates the boiler output into the heating circuit based on the indoors temperature 8 4 5 Boiler operation with isothermal regulation The boiler regulates the CH temperature based on changes in the outside temperature For this type of regulation it is necessary to use a regulator with an isothermal regulation function Protherm Thermolink B Thermolink P or Thermolink RC and to connect it to the outside temperature sensor Caution Setting the maximum CH water temperature on the boiler control panel may influence the isothermal regulation The CH water temperature selected at the boiler control panel is also the limiting temperature The room regulator setting cannot override the heat limit temperature set at the boiler control panel Setting an appropriate CH water temperature at th
Download Pdf Manuals
Related Search