User Manual
Contents
1. automatically saved after 8 seconds Press the ENTER button again to select the mode display inversion To go back to the functions press the MENU button Press and hold the MENU button for one second or wait for one minute to go back to the main menu Display normal mode is for floor standing the unit Display inversion mode is for hanging the unit upside down Pan Inversion Press the MENU button to select ui Press the ENTER button and the display will blink Use the DOWN and UP buttons to select the an normal or pan inversion mode Once the mode has been selected press the ENTER button to confirm To go back to the functions without any changes press the MENU button again Press and hold the MENU button for one second or wait for one minute to go back to the main menu hal He Tilt Inversion Press the MENU button to select k Hel Press the ENTER button and the display will blink Use the DOWN and UP buttons to select the OM normal or tilt inversion mode Once the mode has been selected press the ENTER button to confirm To go back to the functions without any change press the MENU button again Press and hold the MENU button for one second or wait for one minute to go back to the main menu Auto Test Press the MENU button to select IEE SE Press the ENTER button and the unit will run a self test with its built in programs To go back to the functions without any changes press th2. EQUINOX SLENDOR BEAM WHITE Contents 1 Safety Instructions 2 Features amp Specifications 3 How To Set The Unit 4 Troubleshooting 5 Fixture Cleaning User Manual EQLEDO13 1 Safety Instruction Please read the instructions carefully as they include important WARNING information about installation usage and maintenance Please keep this User Guide for future consultation If you sell the unit to another user be sure that they also receive this Unpack and check carefully that there is no transportation damage before using the unit Before operating ensure that the voltage and frequency of the power Supply match the power requirements of the unit It s important to ground the yellow green conductor to earth in order to avoid electric shock The unit is for indoor use only Use only in a dry location The unit must be installed in a location with adequate ventilation at least 50cm from adjacent surfaces Be sure that no ventilation slots are blocked Disconnect the mains power before replacement or servicing Make sure there are no flammable materials close to the unit while operating as they may cause a fire hazard Always use a Safety cable when installing this unit Do not carry the unit with its head only always carry it using the base The maximum ambient temperature is 40 C Don t operate it where the temperature is higher than this In the event of a serious operating problem stop using the
3. NU button again Press and hold the MENU button for one second or wait for one minute to go back to the main menu Press the MENU button to select Eid Press the ENTER button and the display will blink Use the DOWN and UP buttons to select the _an sound on or Ar ip sound off mode Once the mode has been selected press the ENTER button to confirm To go back to the functions without any changes press the MENU button again Press and hold the MENU button for one second or wait for one minute to go back to the main menu gens Sound Sensitivity Press the MENU and use the UP and DOWN buttons to select BENSI and select the sound sensitivity between value O and 255 Press the ENTER button for confirmation after value selection To go back to the functions without any changes press the MENU button again Led Display Press the MENU button to select tc Press the ENTER button and the display will blink Use the DOWN and UP buttons to select the _ Led display on or ore Led display off mode Once the mode has been selected press the ENTER button to confirm To go back to the functions without any changes press the MENU button again Press and hold the MENU button for one second or wait for one minute to go back to the main menu Display Inversion Press the MENU button to select B SA Press the ENTER button to change the mode display normal It will be
4. e MENU button again Press and hold the MENU button for one second or wait for one minute to go back to the main menu race Press the ENTER button and all channels of the unit will return to their standard position 4 How To Control The Unit 1 Master slave built in preprogram function 2 Universal DMX controller There is no need to turn the unit off when you change the DMX address as new DMX address setting will be effected at once Every time you turn the unit on it will show sione on the display and move all the motors to their home position and you may hear some noises for about 20 seconds After that the unit will be ready to receive a DMX signal or run the built in programs 4 1 Master Slave Built In Preprogrammed Function By linking the units in master slave connection the first unit will control the other units to give an automatic sound activated synchronized light show This function is good when you want an instant show You have to set the first unit as master and select show 1 show 2 show 3 or show 4 from the Show Mode The other units must be set to either Slave 1 normal or Slave 2 2 light show mode A DMX cable between the units for daisy chaining is needed 2 light show In slave mode Slave 1 means the unit works normally and Slave 2 means 2 light show In order to create a great light show you can set Slave 2 on the second unit to get contrast movement to each other even if you have two units o
5. he functions without any changes press the MENU button again Press and hold the MENU button for one second or wait for one minute to go back to the main menu reno _ tt Channel Mode Press the MENU button to select Lh Press the ENTER button and the display will blink Use the DOWN and UP buttons to select the 1 Channel or 7 Channel mode Once the mode has been selected press the ENTER button to confirm To go back to the functions without any changes press the MENU button again Press and hold the MENU button for one second or wait for one minute to go back to the main menu Had Master Mode or Set Slave Mode Press the MENU button to select Press the ENTER button and the display will blink Use the DOWN and UP buttons to select the ELl i Slave 1 Slave 2 or nast Master mode Once the mode has been selected press the ENTER button to confirm To go back to the functions without any changes press the MENU button again Press and hold the MENU button for one second or wait for one minute to go back to the main menu A A O SOS JUO Show Mode Press the MENU button to select d Press the ENTER button and the display will blink Use the DOWN and UP buttons to select the In i show 1 or 5h show 2 or Bh 3 show 3 or Bh show 4 mode Once the mode has been selected press the ENTER button to confirm To go back to the functions without any changes press the ME
6. led Dimension 2 0 x 160 x 110mm Weight 2 5 kg Pan Tilt 540 180 Power sockets IEC XLR sockets 3 pin XLR IN OUT 3 How To Set The Unit The main functions are as below 1CH 7CH MAST SL1 SL2 SH1 LJ SH2 Display ue Shows the various menus and selected functions SH4 Button ON MENU Selects the programming functions SOUN OFF To go forward in the selected functions SENE 000 100 DOWN To go backward in the selected functions ENTER Confirms the selected functions LED 2 Mains input OFF Connection to the power supply DISP INVERT DMX input output PAN INVERT For DMX 512 linking Use a 3 pin XLR cables to link to the controller or to other units TILT INVERT 3 2 Main Functions _ TEST To select any of the given functions press the MENU button up to where the required function is showing on the display Select the function by pressing VER the ENTER button and the display will blink Use the DOWN and UP RSET buttons to change the mode Once the required mode has been selected press the ENTER button to confirm To go back to the functions without any changes press the MENU button again Press and hold the MENU button for one second or wait for one minute to go back to the main menu Cy 4 4 moc DMX Address Setting Press the MENU button to select cdc Press the ENTER button and the display will blink Use the DOWN and UP buttons to choose the address to confirm To go back to t
7. nly 4 2 DMX Controller By using a universal DMX controller to control the units you will need to set a DMX address from 1 to 512 so that the units can receive a DMX signal Press the MENU button until cdr js Showing on the display Press the ENTER button and the display will blink Use the DOWN and UP buttons to change the DMX 512 address Once the address has been selected press the ENTER button to confirm To go back to the functions without any changes press the MENU button again Press and hold the MENU button one second or wait for one minute to go back to the main menu Please refer to the below diagram to address your first 4 units Channel Unit 1 mode Address Unit 2 Address 2 4 3 DMX 512 Configuration 1 CHANNEL MODE Unit 3 Unit 4 Address Address Channel _ Blackout 188 255 Random shows 7 CHANNEL MODE 0 255 0 255 Tit PAN TILT Speed slow fast 011 255 4 Troubleshooting Following are a few common problems that may occur during operation and some suggestions for easy troubleshooting A The unit does not work no light and the fan does not work 1 Check the connection of the power and the main fuse B Not responding to DMX controller 1 DMX LED should be on If not check DMX cables to see if linked correctly 2 If the DMX address is showing but no response to the controller check the address settings and DMX polarity 3 Try another DMX controller C No
8. response to the sound 1 Make sure the unit is not receiving a DMX signal 2 Check the microphone to see if it is good by tapping it The microphone is located on the bottom plate of the unit 5 Fixture Cleaninc The cleaning of external optical lenses must be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates damp smoky or particularly dirty surrounding can cause a greater accumulation of dirt on the unit s optics Clean with a soft cloth using normal glass cleaning fluid or mild soapy water e Always dry the parts carefully e Clean the external optics at least every 20 days
9. unit immediately Never try to repair the unit by yourself Repairs carried out by unskilled people can lead to damage or malfunction Please contact the nearest authorized technical assistance center Always use the same type Spare parts Do not touch any power cables during operation as the high voltage may cause an electric shock Warning e To prevent or reduce the risk of electrical shock or fire do not expose the unit to rain or moisture Do not open the unit within five minutes after switching off e The housing and lenses must be replaced if they are visibly damaged Installation The unit should be mounted via its screw holes onto the bracket Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating Make sure that the structure to which you are attaching the unit to is secure and is able to support a weight of 10 times of the unit s weight Always use a Safety cable that can hold 12 times of the weight of the unit when installing the fixture The equipment must be installed by professionals and it must be installed in a place where is out of the reach of people and no one can pass by or under it 2 Features amp Technical Specifications Control Sound active auto Master slave and DMX 512 modes lt DMX Channels 1CH 7CH Q Electronic dimming 0 100 lt lt Compact size and light weight Voltage 100V 240V 50 60Hz Fuse T 2 5A Power consumption 23W Light source 1 x 10W white
Download Pdf Manuals
Related Search