Home

Intelligent Digital Security IP Camera NCr-302

1. EA a Copyright O 2013 NEXCOM International Co Ltd All Rights Reserved NCr 302 VHR User Manual Chapter 2 Camera Configuration N lt C O M Send Email Notification Check this option to send an email notifying about the alarm event for more information on configuring the email address please refer to SMTP on page 27 Alarm Output Check this option to activate the device connected to alarm output when alarm in is triggered Save Save button to apply the configurations click on this button once all the settings are confirmed for the new changes to take effect Reset Reset button to discard all the settings applied EA a Copyright O 2013 NEXCOM International Co Ltd All Rights Reserved 33 NCr 302 VHR User Manual Chapter 2 Camera Configuration N lt C O M Ea System Audio Settings Audio In Enable Audio Enables or disables audio in on the camera When enabled specify the This section is used to configure the audio settings volume in the Audio In Volume textbox The range is 1 100 Audio Out Enable dui Enables or disables audio out on the camera When enabled specify the volume in the Audio Out Volume textbox The range is 1 100 Audio In Enable Save Audio In Volume 80 Range 1 100 Save button to apply the configurations click on this button once all the settings are confirmed for the new changes to take effect Audio Out Volume 80 Range 1 100 Reset Reset button to discard all t
2. Upload stream to FTP server File format AVI Send email notification Alarm Output When Alarm In Triggered Save stream to SD card File format Avi Upload stream to FTP server File format Avi Send email notification Alarm Output When Motion Detection Triggered Save Stream to SD Card Check this option to store the video stream onto the SD card Select the desired file format in the drop down menu the options are AVI and JPEG Upload Stream to FTP Server Check this option to upload the video stream to a FTP server Select the desired file format in the drop down menu the options are AVI and JPEG For information on configuring the FTP server please refer to FTP on page 26 Send Email Notification Check this option to send an email notifying the event for more information on configuring the email address please refer to SMTP on page 27 Alarm Output Check this option to activate the device connected to alarm output when motion detection is triggered When Alarm In Triggered Save Stream to SD Card Check this option to store the video stream onto the SD card Select the desired file format in the drop down menu the options are AVI and JPEG Upload Stream to FTP Server Check this option to upload the video stream to a FTP server Select the desired file format in the drop down menu the options are AVI and JPEG For information on configuring the FTP server please refer to FTP on page 26
3. EA MA Copyright O 2013 NEXCOM International Co Ltd All Rights Reserved 24 NCr 302 VHR User Manual Chapter 2 Camera Configuration aa Network IP Address Configuration Enable DHCP TCP IP Enables DHCP use this feature if the camera is connected to a network with This section configures the network settings of the camera DHCP server TCP IP Static IP Address IP Address Configuration To manually configure an IP address select this option and input the IP Enable DHCP Static IP address IP Address Subnet Mask Default Gateway Primary DNS Server Secondary DNS Server Enable IPv6 IP Address Current Network Settings IP Address Subnet Mask Default Gateway Primary DNS Server Secondary DNS Server 192 168 1 168 255 255 255 0 192 168 1 254 192 168 11 192 168 1 2 Po 192 168 1 168 255 255 255 0 192 168 1 254 192 168 1 1 192 168 1 2 ol address subnet mask default gateway primary and secondary DNS server address Enable IPv6 To manually configure an IPv6 address select this option and input the IPv6 address Current Network Settings Displays the current IP address subnet mask default gateway primary and secondary DNS server address of the camera Save Save button to apply the configurations click on this button once all the settings are confirmed for the new changes to take effect Reset Reset button to discard all the settings applied EA a Copyright O
4. Range 1 100 H MA Copyright O 2013 NEXCOM International Co Ltd All Rights Reserved 29 NCr 302 VHR User Manual Chapter 2 Camera Configuration Detection Zones This section shows the live video from the camera the screen is divided into 5x5 rectangular boxes to setup motion detection please follow the instructions below 1 Check the Enable motion detection option and specify the sensitivity level 2 In the live video screen below select the desired area for motion detection by clicking on the rectangular box The border of the box will turn red indicating that it is selected You can select multiple boxes up to 5x5 boxes can be selected 3 Press the Save button once all the desired areas are selected for the changes to take effect Motion Detection Enable motion detection Sensitivity Range 1 100 Highlighted box NEX Copyright 2013 NEXCOM International Co Ltd All Rights Reserved Motion Detection Enable motion detection Sensitivity 50 Range 1 100 Area with motion detect enabled To remove motion detection from an area click the box to deselect it then press the Save button for the changes to take effect NCr 302 VHR User Manual Chapter 2 Camera Configuration Alarm In Out Trigger This section configures the IP camera to work with external alarm in out devices Alarm In Out Actions Alarm In Control Alarm In mode Disable m Alarm In L
5. Supported protocols HTTP TCP IP UDP RTP RTSP FTP SMTP DHCP DNS DDNS NTP uPnP ONVIF IPv4 v6 Security Multi level passwords HTTP encryption I O Connector Audio in out port Terminal block 1 in 1 out DIO DIx1 DO x1 RS485 N A Micro SD slot Yes RJ45 Yes Event Management Event trigger Motion detection DI Notifications Trigger alarm output email FTP and record video to server or SD card Post recording Yes Pre recording Yes Power DC DC 12V AC 24V POE Yes IEEE 802 3af EA sa Copyright 2013 NEXCOM International Co Ltd All Rights Reserved NCr 302 VHR User Manual Chapter 1 Product Introduction General Power consumption 13W max Weight 2kg Dimension 406 22 D x 161 W x 263 3 H mm Operating Temp 40 C 60 C Humidity 90 RH no condensation Certification CE FCC Vandal resistant IK10 Outdoor capable IP66 1P67 built in heater Application SDK available for application development EA a Copyright 2013 NEXCOM International Co Ltd All Rights Reserved NCr 302 VHR User Manual Chapter 1 Product Introduction DI O amp Function Description SB Module MB Module Dehumidifier LY Packet Bracket Latch 8 PCS LED IR Illuminator Board Plate Line out Line in Ethernet PoE_ DC12V e AC24V Default Micro SD aan Heater module DI O Note Default If the defa
6. lt C O M Configuring the Camera s Setting 1 To configure the camera s setting click on the Setup button on the main screen to enter the configuration menu Setup 3MP Outdoor IR Bullet Camera T Event Status 2 Zoom Control 9 Optical zoom Focus Control il dica gt Display Focus Zone Event Type NEX Ml MA Copyright O 2013 NEXCOM International Co Ltd All Rights Reserved 14 NCr 302 VHR User Manual Chapter 2 Camera Configuration Browsing Through the Configuration Menu The layout of the configuration menu is split into two sections All the camera settings are located on the left hand side of the interface clicking It will open their corresponding sub menu on the right 3MP Outdoor IR Bullet Camera Live View HEE Basic Settings Video Stream Settings The following are the camera settings available on the left hand side Video Video Stream Camera Settings Overlay Settings Privacy Mask Network Video Stream Camera Settings H 264 Overlay Settings Resolution 1920x1080 16 9 y Privacy Mask FrameRate 30 fps Range 5 60fps Bit Rate Control enoe OVBR OcBR TCP IP b FTP Target bitrate 10000 kbit s Range 30 20000 kbit s SMTP Ports GOP Length 1 seconds Motion Detection 1 264 Alarm In Out Trigger Event Actions Resolution 720x480 3 2 r FrameRate 15 fps Range 0 30fps Stream off 0
7. 2013 NEXCOM International Co Ltd All Rights Reserved NCr 302 VHR User Manual Chapter 2 Camera Configuration FTP This section configures the FTP server address that the camera will connect to FIP FIP Server Host name or IP address 192 168 1 1 default folder Upload path Port Number Login Information User Name tpuser h Password Test Remote FTP server Server status FTP Test as FTP Server Host Name or IP Address Specify the host name or IP address of the FTP server Upload Path Specify the directory that the camera will upload data to Port Number Specify the port number of the FTP server Login Information Username Specify the login username for the FTP server Password Specify the login password for the FTP server Test Remote FTP Server Server Status Displays the status of the test connection FTP Test Tests the network connection between the camera and FTP server Save Save button to apply the configurations click on this button once all the settings are confirmed for the new changes to take effect Reset Reset button to discard all the settings applied EA a Copyright O 2013 NEXCOM International Co Ltd All Rights Reserved NCr 302 VHR User Manual Chapter 2 Camera Configuration SMTP This section configures the SMTP mail server address that the camera will use for sending emails SMTP SMTP Server Mail server 192 168 1 1 Host nam
8. 23 DVO Pin Definition Waterproof Connector Descripti0N 4 nn 23 Cane VANNO DSE HOF asariari naa aaa EDR Eb te a MASK LIM doit 24 Cable Outlet DEER en E REE 6 A E A tnnntmsdeayoin cnn sage E E 25 BU IA SUMAN NOM sneer enacts cena NNE e re 25 i IP Address Configuration merino ironia 25 Chapter 2 Camera Configuration Current Network SettiMQS ccocooccccccoocccnncononnnncoconnncnononnnccnnnnnnnononos 25 Accessing the Camera s Configuration Menu Graphical User Interface 8 A E 26 PISTAMING IP EINDER ormen teten lean 8 FT PE SENE e E PEE A nede Ad ERE see Ade reen 26 EA a Copyright 2013 NEXCOM International Co Ltd All Rights Reserved il NCr 302 VHR User Manual ES Eo li AON ac soner E keen e 26 MNS INS A A IA A 38 Test Remote FIP SEA arca 26 Date amp Time Format aandelige AE ln 39 A nn erne 27 DE SEN PA No qn PP E 39 A GM E E ren E ETE E E A N sant 27 Firmware UDS ascii EEE EANA EARANN AEE 40 LOGIA WT OUI ON apro catarata aims 2 Firmware Version oocccccnccccoccccnnncnonocnnnnnnonnonnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnns 40 To Mail AQU FeSS occcccoonncnccccncnnnccononcnococnnnnnoncnnnnnnnnnnnnnnconononinenoness 27 ETE a a APP A 40 A o E E A E A 28 A E N PE E E E E E 41 a A EE E ATE AEE E A A A EE EE A E ene 28 E EE O E IE A 41 E PA E E E E E A EE T T 28 Camera Name SEN GS scanner 41 A E E E tan 29 Advanced SENOS serani E pane 42 Motion PTE CTO NI eserse rrien ensia AE TANE a SR AERE EASA ain 29
9. 3 MJPEG Resolution 1280x720 16 9 FrameRate 10 fps Range 0 30fps Stream off 0 Quality Good y ee oe ec Stream 1 Resolution Configures the resolution of the video stream The options are 2048x1536 4 3 and 1920x1080 16 9 FrameRate Adjusts the frame rate of the video stream the range is 5 30FPS Bit Rate Control Configures the Bit Rate Control mode as VBR variable bit rate or CBR constant bit rate for the stream Target Bit Rate If the Bit Rate Control is set to CBR you can manually set the bit rate in this field the range is 30 20000kbit s GOP Length Configures the GOP length of the stream The options are 0 5 1 2 3 and 4 setting 0 5 seconds will yield the best video quality EA a Copyright 2013 NEXCOM International Co Ltd All Rights Reserved NCr 302 VHR User Manual Chapter 2 Camera Configuration Stream 2 Resolution Contigures the resolution of the video stream The available options are 1280x720 16 9 720x480 3 2 720x576 5 4 640x480 4 3 and 320x240 4 3 FrameRate Adjusts the frame rate of the video stream Setting 0 will disable the stream Bit Rate Control Configures the Bit Rate Control mode as VBR variable bit rate or CBR constant bit rate for the stream Target Bit Rate If the Bit Rate Control is set to CBR you can manually set the bit rate in this field the range is 30 10000kbit s GOP Length Configures the
10. Basic Settings Auto Exposure Configuration Maximum exposure time 1 s Range 7 1000 Maximum sens up gain 32 Range 1 512 Manual Gain Note Exposure mode on basic settings must be non Locked slow shutter or sens up is User Adjusts the camera s gain manually the range IS 1 512 Setting d higher value will increase the camera s signal and produce brighter images for low OS light environments O Auto Manual Exposure Time 1 1 and 2 1 ee Adjusts the camera s exposure manually the range is 1 1 7 1 1 20000 and eee eae LA oe wee 2 1 7 2 1 20000 with 1 20000 being the shortest exposure length Note 0 Min Iris 100 Max Iris EA a Copyright 2013 NEXCOM International Co Ltd All Rights Reserved 43 NCr 302 VHR User Manual Chapter 2 Camera Configuration Camera Settings Advanced Cont P Iris Control Auto Manual Iris value adjust lt 100 gt Range 0 100 Note 0 Min Iris 100 Max Iris IR Cut Filter ICR Control Auto Day mode Night mode Schedule ICR Start time 13 00 End time 17 00 Use mode Day mode Please set the non specified time range use mode IR LED Control Auto control by light sensor Turn on Turn off Schedule IR Start time 13 00 End time 17 00 Use mode Turn on Please set the non specified time range use mode G
11. COD ercon Audio Settings VER OCBR AA Target bit rate 2000 kbit s Range 30 10000 kbit s User Management SD Card Management Date amp Time GOP Length 1 y seconds Firmware Upgrade Maintenance Str eam 3 7 La Y 7 EH Advanced settings MJPEG Resolution 1280x720 16 9 7 FrameRate 10 fps Range 0 30fps Stream off 0 Quality Good y FLE TCP IP FIP SMTP Ports Events Motion Detection Alarm In Out Trigger Event Actions System Audio Settings Recording Settings User Management SD Card Management Date amp Time Firmware Upgrade Maintenance Advanced Settings EA sa Copyright 2013 NEXCOM International Co Ltd All Rights Reserved NCr 302 VHR User Manual Chapter 2 Camera Configuration Video Video Stream This section configures the settings of the video stream There are 3 video streams available the live video from the main screen Viewer is stream 1 Video Stream Settings NA H 264 Resolution 1920x1080 16 9 FrameRate 30 fps Range 5 30fps Bit Rate Control O VBR OCBR Target bit rate 10000 kbit s Range 30 20000 kbit s GOP Length 11 xl seconds Stream 2 H 264 Resolution 720x480 3 2 gt FrameRate 15 fps Range 0 30fps Stream off 0 Bit Rate Control verR OCcBR Target bit rate 2000 kbit s Range 30 10000 kbit s GOP Length 1 seconds Stream
12. Configures the sensitivity of the face recognition the range is 1 9 with 1 being the least sensitive Detect Direction Contigures the direction to detect faces Up Detect faces on the top 90 degrees trom the front Right Detect faces on the right 180 degrees from the front Left Detect faces on the left 180 degrees from the front Down Detect faces on the bottom 90 degrees from the front Detection Box Configures which detection zones are used for face recognition the options are Rectangle ROI and Rectangle ROI Face Detection Detection Zones Enable Face Detection Setting Area Threshold Range 1 09 Detect direction LJ p Ww Detection box Rectangle w Detection Zone EA a Copyright 2013 NEXCOM International Co Ltd All Rights Reserved NCr 302 VHR User Manual Chapter 2 Camera Configuration N i O M EEES Tampering Detection Settings This section is used to configure tamper detection settings Enable Tampering Detect Enables or disables tamper detection When enabled the camera will trigger Tampering Detection actions enabled in the Event Actions menu upon detecting image blurs tings Sensitivity capa Configures the sensitivity of the tamper detection the range is 1 100 with Sensitivity 80 Range 1 100 1 being the least sensitive EA a Copyright O 2013 NEXCOM International Co Ltd All Rights Reserved 53 NCr 302 VHR User Manual Chapter 2 Camera Confi
13. IR cut filter control mode to use outside of the scheduled time IR LED Control Auto Control by Light Sensor When enabled the camera will automatically turn the infrared LEDs on or off based on the amount of light received by the image sensor Turn on Turns the IR LED on Turn off Turns the IR LED off Schedule IR Enables or disables IR LED control function to activate at the specified time You can configure the Start Time and End Time in 24 hour format Use Mode During Scheduled Hours Selects the IR LED control mode to use during the scheduled time Use Mode Outside of the Scheduled Hours Selects the IR LED control mode to use outside of the scheduled time EA Copyright O 2013 NEXCOM International Co Ltd All Rights Reserved Gamma Control Default Activates the default gamma state Gamma Adjusts the gamma manually the range is 0 01 1 00 with 0 01 being the lowest value Save Save button to apply the configurations click on this button once all the settings are confirmed for the new changes to take effect Reset Reset button to discard all the settings applied aa NCr 302 VHR User Manual Chapter 2 Camera Configuration ROI You can configure up to 5 ROI zones ROI is used to select which areas will be monitored and recorded with higher image quality while using lower image quality for other non ROI zones to save bandwidth and storage The instructions below illustrate how to setup 5 RO
14. N lt C O M 6 Align the mounting holes on the wall mount bracket to the mounting holes on the wall mount plate then secure it tightly with screws to finish the installation 4 Secure the connecting bracket to the cameras rear 5 Press and hold down the latch on the wall mount bracket and put it into the connecting bracket Once in place secure the other side using the supplied hex wrench H LEI NCr 302 VHR User Manual Copyright O 2013 NEXCOM International Co Ltd All Rights Reserved 7 Chapter 2 Camera Configuration CHAPTER 2 CAMERA CONFIGURATION Accessing the Camera s Configuration Menu Graphical User Interface The camera s default IP address is 192 168 1 168 make sure the IP address of the computer accessing the camera is on the same network subnet before proceeding You can access the camera via a web browser or IP FINDER software included with the camera The following information outlines the instructions for each method Installing IP FINDER o Note If IP FINDER is already installed you can skip this section and continue to the next section IP FINDER on page 11 1 Locate the installation file IP FINDER Setup msi on the CD 2 Once located double click on the file to start the installation program 3 Click the Next button on the welcome screen to continue The installer will guide you through the steps required to install IP FINDER on your computer WARNING This
15. Streaming channels 2 videoCodecType H 264 VLC media player RE ok Media Playback Audio Video Tools View Help Ma ae f 2 VLC media player Open File Ctrl O Open Folder Ctrl F 2 Open Disc Ctrl D 22 Open Network Stream Ctrl N a me Playback Audio Video Tools View Help Open Network Stream Open Capture Device Ctrl C Open advanced Ctrl Shift 0 Open Location from clipboard Ctrl V Open Recent Media Save Playlist to File Ctrl Convert Save Ctrl R Stream Ctrl S Quit at the end of playlist 00 19 m vce oa Ean le Ctr Q EA Copyright O 2013 NEXCOM International Co Ltd All Rights Reserved 56 NCr 302 VHR User Manual
16. a An E E E E A T A E sleet 43 e E A E AE 29 Camera Settings AdVanced coccccccccccccccooccnnnnnnnnnnnnnnnnnonenennnnnnnnncnnnns 43 Detection ZOMCS cosmetica 30 Chroma amp Sharpness Suppression ccccoccocccccnnccnooconnnnnnnncnncnnncnnnononnos 43 Alarm A A 31 Manual White Balance oooccccncononnccnnncconcnnnnnnccnnnononnncnnnoninnnnnnnnnons 43 A acters E RE EA TE ERE E SEENDE FEED ERE SENDER 31 Manual Exposure amp Gall sessirnar iaiia 43 Alarm OUT CONIOI ssamaaasatosnevastetasnda A E EA EANN 31 Camera Settings Advanced Cont c coooocccccnnccccncccncnncnnononcnnnnnnncononononos 44 o ee eee et 32 Auto Exposure Configuration ooooooococcnnncnnnnnonononcncnnnnnnnnnnonononenons 44 When Motion Detection Triggered ooononnccnnncconccononccncoccnnnnncnnos 32 o e PR o E o 44 When Alarm In Triggered ococcccccconcnccnncconoconcnnncnononononononononinnncnnss 32 IR CUT Fer TER CONTO ritos 44 PP A AE ren 34 EA AA 45 E EET S E eee 34 e ON Ol A E E E EE 45 Audio Settings ira a lara acia 34 A SS A 46 Recording SEIN E NE re Pm 35 Auto Exposure Weights ooooccccccccooccccnncccoonononnncnnnonononnnnnncononnncnnnononoos 47 AVI File SENE rc dia 35 ONO e ny E E E 48 user Manga e oasa REAREN EEEE ASi 36 DION riada I iii iso E EA E A T T 48 Add Modity User ACCOUNTS c0ccccccccseeeceeceteuseseceereaneeesesensenees 36 DNS Uco 48 A A oaaieeSaseatae E A EAT 36 A ea E 49 SD Card Manageme nt oocccnnncncnccnnnncncnocnnnnnncnnnonnnn
17. can select the maximum level of amplification in the drop down list The options are 4x 8x 16x and 32x A higher value will produce brighter images but may also increase image noise Enable Backlight Compensation Enables or disables backlight compensation function enable this option if an image in the camera is too dark Day amp Night Configures the day and night mode of the camera Auto Allows the camera to automatically sense the current lighting level and determine what type of color range it should display Forced Color Forces the camera to display color regardless of the current lighting level Forced Black amp White Forces the camera to display black amp white images regardless of the current lighting level Schedule Day amp Night Enables day and night mode to activate at the specified time You can configure the Start Time and End Time in 24 hour format Use Mode During Scheduled Hours Selects the color mode to use during the scheduled time Use Mode Outside of the Scheduled Hours Selects the color mode to use outside of the scheduled time Save Save button to apply the configurations click on this button once all the settings are confirmed for the new changes to take effect Reset Reset button to discard all the settings applied OM eee Copyright 2013 NEXCOM International Co Ltd All Rights Reserved NCr 302 VHR User Manual Chapter 2 Camera Configuration Overlay Sett
18. the Enter button 3 You will be prompted with a pop up window asking for login information type in admin default login name and 9999 default password 4 Once logged in you will see the main screen with video stream stream 3 Snapshot Start Stop Viewer Setup Live view 3MP Outdoor IR Bullet Camera Event Status O Zoom Control Optical zoom A r m PTZ Zoom Control y Focus Control Focus 4 a gt contro ial Display Focus Zone Foc u S 4 Zone Event Type NEX Copyright 2013 NEXCOM International Co Ltd All Rights Reserved Snapshot Takes a image snapshot from the camera you will be prompted to store the image file onto the computer s hard drive Start Stop Press to stop the live video press again to restart Viewer Views the live video of the camera Setup Options for configuring the IP camera PTZ Zoom Control Buttons used to control zooming and PTZ function Moves the camera up down left and right Returns the camera back to default position A w as the camera to zoom in or out Focus Control Adjusts the camera s focus To adjust the focus automatically press the Auto Focus button To set the focus manually press the to focus far objects and gt to focus near objects Focus Zone Enables or disables display of focus zone in the center of the live view cross hair NCr 302 VHR User Manual Chapter 2 Camera Configuration NM
19. Configures the port numbers for RTP audio and RTCP the range is 1025 65535 TTL Configures the time to live threshold of the multicast datagram before it is discarded by the router EA a Copyright 2013 NEXCOM International Co Ltd All Rights Reserved NCr 302 VHR User Manual Chapter 2 Camera Configuration N i O M Events Settings Enable Ethernet Lost Detection Ethernet Lost Detection This page is used to configure link failure detection for Ethernet Enables link failure detection of the Ethernet connection Alarm Output Enables the camera to trigger the device connected to alarm output upon Ethernet Lost Detection i i detecting failure of the Ethernet connection Enable ethernet lost detection Alarm Output EA a Copyright 2013 NEXCOM International Co Ltd All Rights Reserved 51 NCr 302 VHR User Manual Chapter 2 Camera Configuration Face Detection You can configure the camera to detect faces and trigger the events enabled in the Event Actions menu on page 54 The instructions below illustrate how to setup face detection 1 Check the Enable Face Detection and on the live video screen below select the area for face recognition by holding down the mouse button and drag to make a rectangular square release the button once the desired area is covered 2 Press the Setting Area button to set this area for face recognition To delete the area press the Remove button Threshold
20. DDNS account Password Password of the DDNS account Hostname Hostname of the DDNS account Internet IP Address Displays the IP address assigned when the connection is established Manual Used to manually specify an IP address of a DDNS server Status Displays the connection status of the DDNS service OM eee Copyright 2013 NEXCOM International Co Ltd All Rights Reserved NCr 302 VHR User Manual Chapter 2 Camera Configuration SNMP Simple Network Management Protocol SNMP is a protocol that can be used to manage and monitor SNMP enabled devices over a network The SNMPv1 SNMPv2 and SNMPv3 settings for the IP camera can be configured in this page SNMP SNMP v1 v2 W Enable SNMP v1 v2 Traps for SNMP v1 v2 Enable traps Trap address Trap community public SNMP v3 Enable SNMP v3 username user password O CL SNMP v1 v2 Enable SNMP v1 v2 Enables or disables SNMPv1 and SNMPv2 support Read Community Used to configure the read community string Write Community Used to configure the write community string Traps for SNMP v1 v2 Enable Traps Enables the IP camera to send SNMP trap messages Trap Address Specifies the IP address of the trap server to receive the trap messages Trap Community Used to configure the trap community string SNMP v3 Enable SNMP v3 Enables or disables SNMPv3 support User name Used to configure the SNMPv3 username User pass
21. GOP length of the stream The options are 0 5 1 2 3 and 4 setting 0 5 seconds will yield the best video quality Stream 3 Resolution Displays the resolution of the video stream FrameRate Adjusts the frame rate of the video stream Setting 0 will disable the stream Quality Configures the video quality of the stream The options are Best Good and Normal Save Save button to apply the configurations click on this button once all the settings are confirmed for the new changes to take effect Reset Reset button to discard all the settings applied EA oa Copyright O 2013 NEXCOM International Co Ltd All Rights Reserved NCr 302 VHR User Manual Chapter 2 Camera Configuration Camera Settings This section adjusts the camera s image settings Camera Settings Quick viewer Brightness lt 128 gt Range 0 255 Contrast 128 Range 0 255 Color Saturation e Range 0 255 Sharpness 128 gt Range 0 255 Mirror amp Flip Enable mirror Enable flip Wide Dynamic Range WDR WDR mode Schedule WDR Start time 13 00 End time 17 2100 Use mode off 7 Please set the non specified time range use mode White Balance White balance mode auto Image Adjustments Brightness Configures the brightness of the image the range is O 255 with O being the lowest brightness Press the lt button to decrease the value or gt button to increase the value
22. I zones 1 To create ROI zone 1 check the Enable ROI zone 1 and on the live video screen select the area to set the ROI by holding down the mouse button and drag to make a rectangular square release the button once the desired area is covered 2 Press the Setting Area button in Enable ROI zone 1 to set this area as the ROI 3 Repeat the above steps to create ROI for zones 2 to 5 To delete an area check the ROI zone number you like to remove and press the Remove button NEX Copyright 2013 NEXCOM International Co Ltd All Rights Reserved Remove E Enable ROI zone 3 setting Area Remove E Enable ROI zone 4 Setting rea Remove E Enable ROI zone 5 Setting Area Remove ROI zone 1 ROI zone 2 NCr 302 VHR User Manual Chapter 2 Camera Configuration Auto Exposure Weights You can select up to 5 areas and configure the exposure weighting for each area manually The weighting determines the importance of the area captured a higher weighting value will increase the sensitivity of the auto exposure 1 To create an auto exposure area select User Define and check the Enable Regional weighting 1 2 On the live video screen select the area by holding down the mouse button and drag to make a rectangular square release the button once the desired area is covered 3 Press the Setting Area button in Enable Regional weighting 1 4 Configure the weighting value in the corresp
23. NEXCOM International Co Ltd Intelligent Digital Security IP Camera NCr 302 VHR User Manual NEXCOM International Co Ltd Published October 2015 WWW Nexcom com CONTENTS Preface PRINDER a 11 A sean idtancotneines tea rer V Web Browser Internet Explorer ccoo 13 BISE iN EAA AE A N AE EE A EEA E ERE V Configuring the Camera s Setting cesser renee 14 Acknowledgements ccc cece cece ee ccccee ee ececeeeeeeceeeeeeeeeseeeeeeeeseeeeeeeeneeeeeeanees V Browsing Through the Configuration Menu ss ieee 15 Regulatory Compliance Statements ana y Video PE EE A a 16 Declaration of OON OMIY n i video MC ibi 16 ROMS COMPUARES etica iria daa vi CUS TTT 16 Safety IOMA O Ria vil UCTUNESESSEESETTTEESEEETTETETETTTTETIITEEE V7 A AONE I NE fi Stream 3 eres 17 A viii Camera settings E ERE ESEES 18 Technical Support and Assistance ccccccoccccnccnoccnncnnocnnnnnononononnnnnnnnonininnnono iX BUGS Adjustments OE ERE SEE eee 18 A Wicca tart T coe eee Mirror amp Flip A E o o A nee sate 19 delo Ae PO ne en ent orn en E ENE eno oer enn ene X Wide Dynamic Range WDR coccion cnn 19 camera SENINGS CONG sr 20 Chapter 1 Product Introduction Woite Baldaii Essia a di 20 OVE E E E A AA A A E A 1 a Oe 5h Key Features mere AS 1 Overlay Settings esses 2 Hardware Specifications KA 2 CON oc oie Eee ES E EEE A 22 DI O amp Function DESEO UOM dvi acer re earkouL ji a EE E ENNE N AA ANNAR I NON A
24. The default value is 128 Contrast Configures the contrast of the image the range Is O 255 with O being the lowest contrast Press the lt button to decrease the value or gt button to increase the value The default value is 128 Color Saturation Configures the color saturation of the image the range is O 255 with 0 being the lowest saturation Press the lt button to decrease the value or gt button to increase the value The default value is 128 Sharpness Configures the sharpness of the image the range is 0 255 with 0 being the lowest sharpness Press the lt button to decrease the value or gt button to increase the value The default value is 128 Default Default button to discard all the settings applied to Image Adjustments EA Sa Copyright O 2013 NEXCOM International Co Ltd All Rights Reserved NCr 302 VHR User Manual Chapter 2 Camera Configuration QuickViewer Click this button to open up a small preview window of the live video you can view the image as you make image adjustments Click the Save button for the changes to take effect Camera Settings Image Adjustment close x Brightness 128 Contrast 128 Color Saturation 128 Sharpness 128 Mirror amp Flip Enable mirror Mirror Flip Enable Mirror Flip the camera image horizontally Enable Flip Flip the camera image vertically Wide Dynamic Range WDR WDR Mode Enables or disables WDR function en
25. XCOM has established an engineering and manufacturing task force to implement the introduction of green products The task force will ensure that we follow the standard NEXCOM development procedure and that all the new RoHS components and new manufacturing processes maintain the highest industry quality levels for which NEXCOM are renowned The model selection criteria will be based on market demand Vendors and suppliers will ensure that all designed components will be ROHS compliant How to recognize NEXCOM RoHS Products For existing products where there are non ROHS and RoHS versions the suffix LF will be added to the compliant product name All new product models launched after January 2013 will be ROHS compliant They will use the usual NEXCOM naming convention A PP seme Copyright O 2013 NEXCOM International Co Ltd All Rights Reserved NCr 302 VHR User Manual Preface Warnings Read and adhere to all warnings cautions and notices in this guide and the documentation supplied with the chassis power supply and accessory modules If the instructions for the chassis and power supply are inconsistent with these instructions or the instructions for accessory modules contact the supplier to find out how you can ensure that your computer meets safety and regulatory requirements Cautions Electrostatic discharge ESD can damage system components Do the described procedures only at an ESD workstation If no such s
26. able this option if the camera Is exposed to bright backlight glare or high contrast lighting You can specifiy the WDR constrast level as low middle or high Selecting high will produce the best image quality Schedule WDR Enables or disables WDR function to activate at the specified time You can configure the Start Time and End Time in 24 hour format Use Mode During Scheduled Hours Selects the WDR constrast level to use during the scheduled time Use Mode Outside of the Scheduled Hours Selects the WDR constrast level to use outside of the scheduled time EA a Copyright 2013 NEXCOM International Co Ltd All Rights Reserved NCr 302 VHR User Manual Chapter 2 Camera Configuration Camera Settings Cont White Balance White balance mode auto Exposure Exposure mode Auto le Exposure value adjust 128 Range 0 255 Enable slow shutter Maximum exposure time 1 7 y Enble sens up Maximum sens up gain 32x y Enable backlight compensation Day amp Night Auto Forced color Forced black amp white Schedule Day amp Night Start time 13 00 End time 17 00 Use mode color Please set the non specified time range use mode color Tr White Balance White Balance Mode Enables or disables the white balance function on the camera White balance allows the camera to produce more accurate c
27. am1 Stream 2 RTSP port 8556 Path rtsp 192 166 1 165 6556 live stream2 Stream 3 RTSP port 6555 Path rtsp 192 166 1 166 6555 live stream3 Range 554 1025 65535 Copyright O 2013 NEXCOM International Co Ltd All Rights Reserved Configures the HTTP port number of the web configuration menu RTSP Stream 1 to 3 RTSP Port Configures the RTSP port number of stream 1 to 3 and displays the URL of stream 1 to 3 The range is 554 1025 65535 Default URL of Stream 1 rtsp cameralP 554 live stream1 Default URL of Stream 2 rtsp cameralP 8556 live stream2 Default URL of Stream 3 rtsp cameralP 8555 live stream3 Save Save button to apply the configurations click on this button once all the settings are confirmed for the new changes to take effect Reset Reset button to discard all the settings applied NCr 302 VHR User Manual Chapter 2 Camera Configuration N cc O NA Events Settings i i Enable Motion Detection Motion Detection This section configures which area of the live video in Viewer will be monitored for detecting motion Enables or disables motion detection function Sensitivity Motion Detection Configures the sensitivity of motion detection the sensitivity determines the amount of motion required to trigger an event the range is 1 to 100 with 1 being the least sensitive For more information on event please refer to O Enable motion detection Event Actions on page 32 Sensitivity
28. amma Control Default Gamma value 0 45 Range 0 01 1 00 Auto Exposure Configuration Maximum Exposure Time Specifies the maximum exposure time when operating in Auto Exposure mode the range is 1 7 1 1000 with 1 1000 being the shortest exposure length Maximum Sens Up Gain Specifies the maximum gain when operating in Auto Exposure mode the range is 1 512 with 1 being the lowest gain P Iris Control Auto When enabled the P Iris will adjust the opening automatically based on the lighting levels in the environment Manual Adjust the opening of the iris manually in the range of 0 100 with O being the smallest value IR Cut Filter ICR Control Auto When enabled the camera will automatically turn the infrared lights on or off based on the lighting levels in the environment Day Mode Enables day mode and turns the IR cut filter control off Night Mode Enables night mode and turns the IR cut filter control on EA a Copyright 2013 NEXCOM International Co Ltd All Rights Reserved NCr 302 VHR User Manual Chapter 2 Camera Configuration Schedule ICR Enables or disables IR cut filter control function to activate at the specified time You can configure the Start Time and End Time in 24 hour format Use Mode During Scheduled Hours Selects the IR cut filter control mode to use during the scheduled time Use Mode Outside of the Scheduled Hours Selects the
29. ble mask zone 2 Enable mask zone 3 ERE Remove EA MA Copyright O 2013 NEXCOM International Co Ltd All Rights Reserved 23 NCr 302 VHR User Manual Chapter 2 Camera Configuration N i O M A Mask Zones Mask Zones You can configure up to 3 privacy masks the instructions below illustrate how to setup 3 privacy masks Enable mask zone 1 f 1 Select the color of the mask in the drop down list Enable mask zone 2 Setting Area Remove 2 To create the first mask check the Enable mask zone 1 and on the Enable mask zone 3 Setting Area Remove live video screen below select the area to mask by holding down the mouse button and drag to make a rectangular square release the button once the desired area is covered 3 Press the Setting Area button in Enable mask zone 1 to set this area Mask area as Mask 4 You will see the selected area turn black or white depending on which color was chosen This example uses black as the mask color Privacy Mask Settings Privacy mask color Black 7 PRET ee eae 5 To create the second and third mask check the Enable mask zone 2 and Enable mask zone 3 options then repeat steps 2 to 3 outlined Enable mask zone 1 earlier Enable mask zone 2 Setting Area Remove Enable mask zone 3 Setting Area Remove To delete a mask check the zone number you like to remove and press the Remove button Rectangular square
30. computer program is protected by copyright law and international treaties Unauthorized duplication or distribution of this program or any portion of it may result in severe civil or criminal penalties and will be prosecuted to the maximum extent possible under the law lt Back Next button EA a Copyright 2013 NEXCOM International Co Ltd All Rights Reserved NCr 302 VHR User Manual Chapter 2 Camera Configuration N i O M aa 4 Confirm the directory that the program will be installed on To specify 6 Specify which user accounts on the computer can access the program a different folder please click on the Browse button and locate the the options are Everyone and Just me desired installation folder Browse ES IP FINDER Select Installation Folder The installer will install IP FINDER to the following folder To install in this folder click Next To install to a different folder enter it below or click Browse Folder C Program Files IP FINDER Browse button Disk Cost Folder C Program Files IP FINDERY button CA Cancel ancel O Everyone EEE Justme _ 4 i a G k t 5 To check the available drives you can install the software to and their pa ance Next button available and required disk space please click on the Disk Cost button User accounts The list below includes the drives you can install IP FINDER to along with each drive s available T C IC k on th e N ext b utton t
31. d All Rights Reserved NCr 302 VHR User Manual Chapter 2 Camera Configuration Date amp Time Format Date Format Configures the format that the date will be displayed in The options are YYYY MM DD MM DD YYYY and DD MM YYYY Time Format Configures the format that the time will be displayed in The options are 12Hrs and 24Hrs NTP Server NTP Server Address If Synchronize with NTP Server is selected as the time mode type in the host name or IP address of the NTP server Save Save button to apply the configurations click on this button once all the settings are confirmed for the new changes to take effect Reset Reset button to discard all the settings applied EA Sa Copyright 2013 NEXCOM International Co Ltd All Rights Reserved 39 NCr 302 VHR User Manual Chapter 2 Camera Configuration N lt C O M OE Firmware Upgrade Firmware Version This section is used to update the IP camera s firmware Application Version Displays the current firmware version Firmware Upgrade Update Firmware Version Specify the Firmware Image File to Upgrade Application version NexWare 02 00 0005 To update the camera s firmware click on the Browse button and locate the firmware image file once the file is selected press the Update button Firmware Update to begin Specify the firmware image file to upgrade Browse The firmware update process will take around 15 minutes to complete during this t
32. e or IP address Port Number Login Information User Name smtpuser Email address from user domain com To Mail Address user domain com Mail address Mail Test Status eat es SMTP Server Mail Server Specify the host name or IP address of the SMTP mail server Port Number Specify the port number of the SMTP mail server Login Information Username Specify the login username for the SMTP mail server Password Specify the login password for the SMTP mail server Email Address From Specify the email address of the sender To Mail Address Mail Address Specify the email address to send the email when an event is triggered by motion detection Mail Test Status Displays the status of the test connection Mail Test Tests the network connection between the camera and mail address Save Save button to apply the configurations click on this button once all the settings are confirmed for the new changes to take effect Reset Reset button to discard all the settings applied EA oa Copyright 2013 NEXCOM International Co Ltd All Rights Reserved NCr 302 VHR User Manual Chapter 2 Camera Configuration FEER Ports HTTP This section configures the HTTP port number of the web configuration HTTP Port menu and RTSP port number of stream 1 to 3 Ports HTTP HTTP port B0 Range 80 1025 65535 RTSP Stream 1 RTSP port 554 Path rtsp 192 166 1 166 554 live stre
33. ect IR exposure calculation WDR Wide Dynamic Range to overcome high contrast lighting environment Outdoor ready IP66 IP67 Active tampering alarm Impact resistant for IK10 Excellent low light noise reduction ONVIF support Extreme weather support 40 C to 60 C EA a Copyright 2013 NEXCOM International Co Ltd All Rights Reserved 1 NCr 302 VHR User Manual Chapter 1 Product Introduction Hardware Specifications Camera Image sensor 1 3 3 megapixel true WDR progressive scan CMOS sensor Lens Motorized 3 10mm F1 4 board type Iris type p iris Day and night Yes IR distance Effective up to 30 meters IR wavelength 850nm 4pcs high power LED IR control Smart IR ICR Yes WDR Yes Image Enhancement Brightness Contrast Saturation Sharpness Backlight compensation Mirror Flip Day Night Anti flicker Video Video compression H 264 MJPEG Video streaming triple streaming H 264 Stream 1 H 264 Stream 2 MJPEG Stream 3 Video resolution 2048 x 1536 to 320 x 240 Video quality VBR CBR Frame rate 2048 x 1536 30 fps 1920 x 1080 60 fps 1280 x 720 60 fps 720 x 576 60 fps 720 x 480 60 fps 640 x 480 60 fps 320 x 240 60 fps Audio Audio streaming Two way Audio compression G 711 8KHz 16bit Audio input Line in Audio output Line out Network Interface 10 100 1000 Mbps Ethernet RJ 45
34. eld Access Level Administrator Has full control read write over every configuration menu item Operator Has full control read write over every configuration menu item in Video and Event only Viewer Only has access read to the live view of the camera main screen User List Displays user accounts available on the camera to edit an account s password click the Edit button then retype the new password in the Password and Confirm Password fields Save Save button to apply the configurations click on this button once all the settings are confirmed for the new changes to take effect Reset Reset button to discard all the settings applied EA a Copyright 2013 NEXCOM International Co Ltd All Rights Reserved NCr 302 VHR User Manual Chapter 2 Camera Configuration SD Card Management This section is used to manage the SD card SD Card Management Format SD card is unavailable SD card available NO SD SD card use NO SD SD Card Overwrite OFF O ON i zile 3 x 4 Folder Name Filename Date Time Size Action SD Card Information If a SD card is installed this section will display information on the availability of the SD card and the percentage of the total storage used Format Formats the SD card all data stored on the SD card will be erased if this option is used SD Card Overwrite Enables or disables overwrite protection for the SD card Press the Save but
35. evel Alarm Out Control Alarm Out mode User mode Alarm Out level Low m Alarm In Control Alarm In Mode Enables or disables monitoring of alarm input Enable this option if an external sensor device connected to the alarm input requires monitoring Alarm In Level Specify the signal level required for triggering the alarm device connected to the alarm output The options are Low and High Alarm Out Control Alarm Out Mode Specify the alarm out mode the options are User Mode and Event Mode When User Mode is selected the alarm output will be triggered based on user configurations When Event Mode is selected the alarm output will be triggered based on the configurations set in Event Actions For more information on Event Actions please refer to page 32 Alarm Out Level Specify the alarm output action to perform when it is triggered The options are Low and High Save Save button to apply the configurations click on this button once all the settings are confirmed for the new changes to take effect Reset Reset button to discard all the settings applied EA a Copyright 2013 NEXCOM International Co Ltd All Rights Reserved NCr 302 VHR User Manual Chapter 2 Camera Configuration Event Actions This section configures what actions to perform when an event is triggered trom motion detection Event Actions When Motion Detection Triggered Save stream to 5D card File format AVI
36. guration Event Actions Advanced This section configures what actions to perform when an event is triggered trom face detection and tampering detection Advanced Event Actions When Face Detection Triggered Save stream to SD card File format AV F Upload stream to FTP server File format Send email notification Alarm Output When Tampering Detection Triggered Save stream to SD card File format AV Upload stream to FTP server File format AV Send email notification Alarm Output When Motion Detection Triggered Save Stream to SD Card Check this option to store the video stream onto the SD card Select the desired file format in the drop down menu the options are AVI and JPEG NECOM Upload Stream to FTP Server Check this option to upload the video stream to a FTP server Select the desired file format in the drop down menu the options are AVI and JPEG For information on configuring the FTP server please refer to FTP on page 26 Send Email Notification Check this option to send an email notifying the event for more information on configuring the email address please refer to SMTP on page 27 Alarm Output Check this option to activate the device connected to alarm output when face detection is triggered When Tampering Detection Triggered Save Stream to SD Card Check this option to store the vide
37. he following A Philips screwdriver A flat tipped screwdriver A grounding strap An anti static pad Using your fingers can disconnect most of the connections It is recommended that you do not use needle nose pliers to disconnect connections as these can damage the soft metal or plastic parts of the connectors A PP emm Copyright O 2013 NEXCOM International Co Ltd All Rights Reserved NCr 302 VHR User Manual Preface Safety Precautions 1 Read these safety instructions carefully 2 Keep this User Manual for later reference 3 Disconnect this equipment from any power sources before cleaning Use a damp cloth Do not use liquid or spray detergents for cleaning 4 For plug in equipment the power outlet socket must be located near the equipment and must be easily accessible 5 Keep this equipment away from humidity 6 Put this equipment on a stable surface during installation Dropping it or letting it fall may cause damage 8 Make sure the voltage of the power source is correct before connecting the equipment to the power source 10 All cautions and warnings on the equipment should be noted 11 1f the equipment is not used for a long time disconnect it from the power source to avoid damage by transient overvoltage 12 Never pour any liquid into an opening This may cause fire or electrical shock 13 Never open the equipment For safety reasons the equipment should be opened only by qualified
38. he settings applied a ts EA a Copyright O 2013 NEXCOM International Co Ltd All Rights Reserved 34 NCr 302 VHR User Manual Chapter 2 Camera Configuration N i O M EEES Recording Settings AVI File Setting This section is used to configure the recording settings of the IP camera Stream Source Selects which video stream number to record the options are Stream 1 and Recording Settings Same rue 3 Save A Sem Save button to apply the configurations click on this button once all the settings are confirmed for the new changes to take effect RET ds Reset button to discard all the settings applied EA a Copyright O 2013 NEXCOM International Co Ltd All Rights Reserved 35 NCr 302 VHR User Manual Chapter 2 Camera Configuration User Management This section is used to manage user accounts for accessing the IP camera s web configuration menu User Management Add Modify User Accounts Operator y Username and password must be for least 1 characters User List User Name User Group User Information Edit User Delete User admin Administrator Administrator ome ed Add Modify User Accounts To add a user account type in the username and password username and password must be at least 1 character retype the password to confirm then choose the access level for the account in the Authority drop down list You can also provide a description for the account under the User Information fi
39. ime do not disconnect the network cable reset or power off the IP camera as you may damage the device EA a Copyright 2013 NEXCOM International Co Ltd All Rights Reserved 40 NCr 302 VHR User Manual Chapter 2 Camera Configuration Bae Maintenance Maintain This section is used to restart the IP camera or restore it to factory default Restart settings Maintenance Maintain Reboot the camera Reset to Default Resets all camera parameters to the factory default settings Camera Name Settings Camera Name Ln FEE m r TEE Click this button to reboot the camera Reset to Default Click this button to restore all the camera s setting back to factory default Camera Name Settings Camera Name Specify a name for the camera The name will be displayed in the upper left corner on the live video stream of the camera To enable this make sure the option Display Camera Name in the Overlay Settings menu is checked For information on the Overlay Settings menu please refer to page 22 Save Save button to apply the configurations click on this button once all the settings are confirmed for the new changes to take effect Reset Reset button to discard all the settings applied EA a Copyright 2013 NEXCOM International Co Ltd All Rights Reserved NCr 302 VHR User Manual Chapter 2 Camera Configuration Advanced Settings NERE The following are the advanced setti
40. ings This section configures the text displayed on the live video in Viewer Overlay Settings Contents Enble date Enable time Enable text texti Display Camera Name Contents Enable Date Enables or disables the Viewer to display the current date on the bottom right corner Enable Time Enables or disables the Viewer to display the current time on the bottom right corner Enable Text Enables or disables the Viewer to display text on the upper right corner The text displayed can be configured in the field box Display Camera Name Enables or disables the Viewer to display the camera s name on the upper left corner The name displayed can be configured in the Maintenance menu For information on Maintenance menu please refer to page 41 Save Save button to apply the configurations click on this button once all the settings are confirmed for the new changes to take effect Reset Reset button to discard all the settings applied EA a Copyright 2013 NEXCOM International Co Ltd All Rights Reserved NCr 302 VHR User Manual Chapter 2 Camera Configuration N i O M EE Privacy Mask Settings This section configures which area of the live video in Viewer will be masked Privacy Mask Color for privacy A total of 3 privacy masks can be configured Selects the color of the privacy mask The available colors are Black and White Privacy Mask Privacy mask color Black m Mask Zones Fl Ena
41. ior written consent from NEXCOM International Co Ltd Disclaimer The information in this document is subject to change without prior notice and does not represent commitment from NEXCOM International Co Ltd However users may update their knowledge of any product in use by constantly checking its manual posted on our website http www nexcom com NEXCOM shall not be liable for direct indirect special incidental or consequential damages arising out of the use of any product nor for any infringements upon the rights of third parties which may result from such use Any implied warranties of merchantability or fitness for any particular purpose is also disclaimed Acknowledgements NCr 302 VHR is a trademark of NEXCOM International Co Ltd All other product names mentioned herein are registered trademarks of their respective Owners Regulatory Compliance Statements This section provides the FCC compliance statement for Class B devices and describes how to keep the system CE compliant Declaration of Conformity FCC This equipment has been tested and verified to comply with the limits for a Class B digital device pursuant to Part 15 of FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruc
42. ngs available on the left hand side This section is used to configure advanced settings of the IP camera 9 9 Video 3MP Outdoor IR Bullet Camera tve view REE Camera Settings RO Advanced Settings Advanced Camera Settings AE Weights Network eT E Enable chroma suppression AE Weights Enable sharpness suppression gt DDNS manuais Balane SNMP a RIG gain 1 0 Range 0 0 4 0 Multicast Multicast BIG gain 1 0 Range 0 0 4 0 Events Events Note Manual White Balance will be enabled while White balance mode on basic settings is off emateen MamilEepore an Ethernet Lost Detection Face Detection Tampering Detection eg Face Detection Manual exposure time 1 60 s Range 7 20000 Tampering Detection e n Note Manual exposure will be enabled while Exposure mode on basic settings is Locked Event Actions Schedule Recording System Maximum exposure time 1 7 s Range 7 1000 Maximum sens up gain 32 Range 1 512 Note Exposure mode on basic settings must be non Locked slow shutter or sens up is User define 9 Auto Manual Iris value adjust lt 100 gt Range 0 100 Note 0 Min Iris 100 Max Iris 9 Auto Day mode Night mode Schedule Recording Basic Settings EA a Copyright O 2013 NEXCOM International Co Ltd All Rights Reserved 42 NCr 302 VHR User Manual Cha
43. nnnnonnnnonnnonnnnneninnnnnnos 37 A EE O T 49 pr o A 37 WS Tor SNMP VINA odo 49 FNS e A E A E 37 Sy e AE E AE AE AAE AEE PEE A 49 B AA A E A A E TEE 38 A 50 Current Camera TIME seee tic i 38 A Eee 50 EA a Copyright 2013 NEXCOM International Co Ltd All Rights Reserved iii NCr 302 VHR User Manual Content Al Bs O Wi ME A nai A E A AEA A gl Ethernet LOSE DOTE israel 51 SE N o PP A 51 o A 52 T mperng DetettORN eucssaitencenaeicnctdeadinseacieebncs sisicddenudviccenuwhedetedeainnctenevienkt Do SE TUS wirddscctsei onseacratesasehm aia E E 53 Event Actions Advanced sense renen enker e renerne 54 When Motion Detection Triggered ooccccccccnccccncoccccnnnnnnnnncnnnnnncnnns 54 When Tampering Detection TrigQered occoccoooononcccnnncnnnnncconnnncnno 54 BSS nn za 33 Schedule Recording wx cnsnsnciidwnunindandctaeontnandtoiswihianandatendanmnaudanamerdniericininans 55 Schedule Recording SettinQ occccccccncnccccoconcccnnnnnnnnnncnononononnninnnnos 55 Chapter 3 Viewing Live Video via VLC Media Player 56 H COM eC Copyright 2013 NEXCOM International Co Ltd All Rights Reserved IV NCr 302 VHR User Manual Preface PREFACE Copyright This publication including all photographs illustrations and software is protected under international copyright laws with all rights reserved No part of this manual may be reproduced copied translated or transmitted in any form or by any means without the pr
44. o 90 seconds Home Page Camera List You can also manually search cameras by clicking on the Search button Firpo a Search IP Address 192 168 110 1419D68A 1DDF 11BF A10F 0010F3344901 00 10 F3 34 49 01 1419D68A 1DDF 11BF A 10F 00 10F3344901 TsBD 10000840 Note Manual search will last for up to 90 seconds NEX MA Copyright O 2013 NEXCOM International Co Ltd All Rights Reserved 11 NCr 302 VHR User Manual Chapter 2 Camera Configuration N lt C O M Multiple Cameras If more than one IP camera are detected the Camera List will show all the available cameras on the network To access all the cameras configuration menu simultaneously click on the Select All button to select all the cameras in the list then click the Home Page button Similarly you can access specific ones by ticking the camera s checkbox To deselect press the Clear All button to remove all the selection or specific ones by unchecking the checkbox Home Page Camera List Clear All Select All Checkbox foo 10 F3 34 49 01 1419D68A 1DDF 11BF A 10F 0010F3344901 T560 10000840 NEX EE Copyright 2013 NEXCOM International Co Ltd All Rights Reserved 12 NCr 302 VHR User Manual Chapter 2 Camera Configuration Web Browser Internet Explorer 1 Locate and open the Internet Explorer IE shortcut on the desktop 2 In the address bar type 192 168 1 168 default IP address of the camera and then press
45. o con ti nue and required disk space Disk Size Available 465GB 465GB EA Copyright O 2013 NEXCOM International Co Ltd All Rights Reserved 9 NCr 302 VHR User Manual Chapter 2 Camera Configuration N i O M 8 Click on the Next button to begin installation 9 Once the installation process is complete click on the Close button to finish A shortcut will be created on the desktop Confirm Installation Installation Complete The installer is ready to install IP FINDER on your computer Click Next to start the installation IP FINDER has been successfully installed Click Close to exit Please use Windows Update to check for any critical updates to the NET Framework Next button Close button OM eee Copyright 2013 NEXCOM International Co Ltd All Rights Reserved 10 NCr 302 VHR User Manual Chapter 2 Camera Configuration N i O M IP FINDER 3 Once the camera is discovered it will show the following information Model name 1 Locate and open the IP FINDER software shortcut on the desktop P address MAC address UUID Serial number Version 4 Click on the Home Page button and it will launch the camera s configuration menu via Internet Explorer You can also access the menu by double clicking the camera s IP address under Camera List 2 When the program is launched it will begin searching the network for the IP camera automatically the search will last for up t
46. o stream onto the SD card Select the desired file format in the drop down menu the options are AVI and JPEG Upload Stream to FTP Server Check this option to upload the video stream to a FTP server Select the desired file format in the drop down menu the options are AVI and JPEG For information on configuring the FTP server please refer to FTP on page 26 Send Email Notification Check this option to send an email notifying about the alarm event for more information on configuring the email address please refer to SMTP on page 27 Alarm Output Check this option to activate the device connected to alarm output when tampering detection is triggered EA Copyright O 2013 NEXCOM International Co Ltd All Rights Reserved NCr 302 VHR User Manual Chapter 2 Camera Configuration N lt C O M System Schedule Recording Setting Enable Schedule Recording Schedule Recording This section is used to schedule the recording of the video streams Enables or disables recording of the video stream Daily Schedule Recording Y Enable Schedule Recording Configures the camera to record at the specified Start Time and End Time Weekly Configures the camera to record on the specified day and time of the week Daily Starttime 00 00 Endtime 23 59 S one o Select this to set full day recording 012 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 Sun S p EE CBee sD D a Select
47. olors under different lighting conditions The following modes can be selected Off Disables white balance function Auto Automatically adjusts the white balance to suit the current lighting condition Fixed Outdoor Adjusts the white balance for outdoor daylight Incandescent Adjusts the white balance for indoor light Fluorescent Adjusts the white balance for fluorescent light Exposure Exposure Mode This option configures the anti flickering function of the camera If the image is suffering trom flickering under fluorescent light selecting Auto will allow the camera to automatically adjust the light frequency to match the current fluorescent lighting condition and prevent flickering You can also manually set it to Anti Flicker 50Hz Anti Flicker 60Hz or Locked Exposure Value Adjust Adjusts the exposure value on the camera the range Is 0 255 Press the lt button to decrease the value or gt button to increase the value The default value Is 128 EA oa Copyright 2013 NEXCOM International Co Ltd All Rights Reserved NCr 302 VHR User Manual Chapter 2 Camera Configuration Enable Slow Shutter Enables or disables slow shutter on the camera you can select the shutter speed in drop the list The options are 1 7 1 15 1 30 Selecting a slower shutter speed will improve image quality in low light conditions but will increase motion blur Enable Sens Up Enables or disables gain setting on the camera you
48. onding textbox the range isO 10 5 Repeat the above steps to create auto exposure weightings for zones 3 to 5 To delete an area check the zone number you like to remove and press the Remove button To allow the camera to adjust the exposure automatically select the Auto option Background Others Configures the weighting value of the area outside of the selected zones Auto Exposure Weights Settings Auto User define Enable Regional weighting 1 la e Range 0 10 ls Range 0 10 C Enable Regional weighting 3 Setting rea Remove A Range 0 10 O Enable Regional weighting 4 Setting y Area Remove lr Range 0 10 C Enable Regional weighting 5 setting Area Remove la li Range 0 10 Background others Range 0 10 Zone 1 Zone 2 EA a Copyright O 2013 NEXCOM International Co Ltd All Rights Reserved NCr 302 VHR User Manual Chapter 2 Camera Configuration leet Network DDNS Settings DDNS Service DDNS This section is used to configure DDNS Dynamic DNS Note Different DDNS service provider may have different input fields DDNS DDNS Settings DDNS Service Dyn WebSite Hostname Internet IP Address E Manual Status Select the DDNS service provider from the drop down list the available providers are Dyn NO IP dnsExit and DtDNS Web Site URL link to the selected DDNS service provider s web site Username Username of the
49. ponding port on the MB module 6 Close the camera s top cover and secure it with the supplied hardware tool to complete Copyright O 2013 NEXCOM International Co Ltd All Rights Reserved 5 NCr 302 VHR User Manual NEX Chapter 1 Product Introduction Cable Outlet Description 1 The camera features two waterproof connectors the left one in the diagram is for PoE connection while right one is for line in line out DC 12V AC 24V and DI O connections 2 The right one features four wire holes Please cover unused holes with sealing plugs to prevent water from entering 3 Applicable cable diameter 4 Y 2 5 1 8mm Right 5 6 9 4 7mm Left i Ethernet Line in DC12V AC24V DI O NEX Copyright 2013 NEXCOM International Co Ltd All Rights Reserved NECOM Hardware Installation 1 Position the placement sticker at the desired installation location and use a driller to drill the three holes on the sticker 2 Insert three screw anchors into the holes then place the wall mount base on top of them with the mounting holes aligned 3 Open the camera s cover and glue the dehumidifier packet onto the metal bracket using the adhesive sticker on its back as depicted in the diagram below Close the camera s cover and ensure the clip is locked in position Install the sunshield and tighten a torx screw on the side of cover NCr 302 VHR User Manual Chapter 1 Product Introduction
50. pter 2 Camera Configuration N lt C O M AES Video Chroma amp Sharpness Suppression Enable Chroma Suppression Camera Settings Advanced Enables or disables chroma suppression Enabling chroma suppression will This section is used to adjust the camera s advanced image settings reduce the image noise captured from low light environments Advanced Camera Settings Quick viewer Enable Sharpness Suppression Chroma amp Sharpness Suppression Enables or disables sharpness suppression Enabling sharpness suppression will minimize the sharpness caused by noise in low light captures Enable chroma suppression Enable sharpness suppression Manual White Balance aan en eee Note To adjust the white balance manually please set the White Balance ee a Mode to Off in Basic Settings BIG gain 1_U Range 0 0 4 0 R G Gain Adjusts the warm white balance the range Is 0 0 4 0 from yellow to red Note Manual White Balance will be enabled while White balance mode on basic settings is off Manual Exposure amp Gain B G Gain Manual gain 1 Range 1 512 i i i Adjusts the cold white balance the range is 0 0 4 0 from green to blue Manual exposure time 1 6U s Range 7 20000 Note Manual exposure will be enabled while Exposure mode on basic settings is Locked Manual Exposu re amp Gain Note To adjust the exposure and gain manually please set the Exposure Mode to Locked in
51. re operating system version application software etc A complete description of the problem The exact wordings of the error messages Caution Information to avoid damaging components or losing data Note Provides additional information to complete a task easily Warning 1 Handling the unit carry the unit with both hands and handle it with care 2 Maintenance to keep the unit clean use only approved cleaning products or clean with a dry cloth EA a Copyright 2013 NEXCOM International Co Ltd All Rights Reserved IX NCr 302 VHR User Manual Preface N e O M Package Contents The 3MP Outdoor IR Bullet Camera package contains the following accessories E 1 Weg Placement sticker Quick guide Dehumidifier packet Mounting accessory kit 2 axis cable concealed wall Sunshield Waterproof connector Wall mount base CD User Manual mount bracket NEX EE Copyright 2013 NEXCOM International Co Ltd All Rights Reserved X NCr 302 VHR User Manual Chapter 1 Product Introduction CHAPTER 1 PRODUCT INTRODUCTION Overview Key Features Progressive scan CMOS sensor at 3 megapixel 1080p full HD resolution Multiple H 264 and MJPEG streams Easy installation with remote focus and zoom control Support Auto Focus to avoid focus error through human eyes Adjustable P iris to achieve best image quality Perf
52. service personnel NECOM 14 If one of the following situations arises get the equipment checked by 15 17 service personnel a The power cord or plug is damaged b Liquid has penetrated into the equipment c The equipment has been exposed to moisture d The equipment does not work well or you cannot get it to work according to the user s manual e The equipment has been dropped and damaged f The equipment has obvious signs of breakage Do not place heavy objects on the equipment CAUTION DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER DISCARD USED BATTERIES ACCORDING TO THE MANUFACTURER S INSTRUCTIONS EA a Copyright 2013 NEXCOM International Co Ltd All Rights Reserved Vill NCr 302 VHR User Manual Technical Support and Assistance Conventions Used in this Manual 1 For the most updated information of NEXCOM products visit NEXCOM s website at www nexcom com Warning Information about certain situations which if not observed can cause personal injury This will prevent injury to yourself 2 For technical issues that require contacting our technical support team or when performing a task Sales representative please have the following information ready before calling Product name and serial number Detailed information of the peripheral devices Detailed information of the installed softwa
53. tation is available you can provide some ESD protection by wearing an antistatic wrist strap and attaching it to a metal part of the computer chassis Safety Information Before installing and using the device note the following precautions Read all instructions carefully Do not place the unit on an unstable surface cart or stand Follow all warnings and cautions in this manual When replacing parts ensure that your service technician uses parts specified by the manufacturer Avoid using the system near water in direct sunlight or near a heating device The load of the system unit does not solely rely for support from the rackmounts located on the sides Firm support from the bottom is highly necessary in order to provide balance stability The network camera is provided with a battery powered real time clock circuit There is a danger of explosion if battery is incorrectly replaced Replace only with the same or equivalent type recommended by the manufacturer Discard used batteries according to the manufacturer s Instructions NECOM Installation Recommendations Ensure you have a stable clean working environment Dust and dirt can get into components and cause a malfunction Use containers to keep small components separated Adequate lighting and proper tools can prevent you from accidentally damaging the internal components Most of the procedures that follow require only a few simple tools including t
54. this to cancel full day recording Wed Y D Thu Aaa e SD Fri sD E SE S D Displays the end time of the recording clicking E will allow you to configure the start time and end time EA Copyright O 2013 NEXCOM International Co Ltd All Rights Reserved BB NCr 302 VHR User Manual Chapter 3 Viewing Live Video via VLC Media Player NEB lt COM CHAPTER 3 VIEWING Live VIDEO via VLC MEDIA PLAYER The IP cameras live video can be viewed by third party media players such TE Open Media a iea as VLC media player by VideoLAN project To stream the live video from Gpe Ops ewok A Capture Device the camera to VLC media player through the network please follow the en instructions below rtsp 192 168 1 168 8557 live streaml E RTSP URL 1 Locate and open VLC media player 2 Go to Media gt Open Network Stream 3 Enter the following RTSP URL rtsp 192 168 1 168 554 live stream1 E Show more options Note RTSP URL of stream 1 similarly you can view stream 2 and 3 of the camera by entering their corresponding URLs Please refer to Ports on page 28 for more information A mi SE ay on the URL link 5 You will be prompted with a pop up window asking for login information type in admin default login name and 9999 default 4 Press the Play button to start streaming password Eam E TET TT rtsp 192 168 1 168 8557 PSIA
55. tions may cause harmful interference to radio communications Operation of this equipment in a residential area domestic environment is likely to cause harmful interference in which case the user will be required to correct the interference take adequate measures at their own expense CE The product s described in this manual complies with all applicable European Union CE directives if it has a CE marking For computer systems to remain CE compliant only CE compliant parts may be used Maintaining CE compliance also requires proper cable and cabling techniques EA a Copyright 2013 NEXCOM International Co Ltd All Rights Reserved NCr 302 VHR User Manual Preface ROHS Compliance NEXCOM RoHS Environmental Policy and Status Update RoHS NEXCOM is a global citizen for building the digital infrastructure We are committed to providing green products and services which are compliant with European Union RoHS Restriction on Use of Hazardous Substance in Electronic Equipment directive 2011 65 EU to be your trusted green partner and to protect our environment Compliant ROHS restricts the use of Lead Pb lt 0 1 or 1 000ppm Mercury Hg lt 0 1 or 1 000ppm Cadmium Cd lt 0 01 or 100ppm Hexavalent Chromium Cr6 lt 0 1 or 1 000ppm Polybrominated biphenyls PBB lt 0 1 or 1 000ppm and Polybrominated diphenyl Ethers PBDE lt 0 1 or 1 000ppm In order to meet the ROHS compliant directives NE
56. ton to apply the setting File List Displays the information of the folders and files stored in the SD card EA a Copyright O 2013 NEXCOM International Co Ltd All Rights Reserved 37 NCr 302 VHR User Manual Chapter 2 Camera Configuration Date amp Time This section configures the date and time on the camera Date amp Time Time 09 42 03 Time mode O synchronize with NTP server O Synchronize with computer time O Manually setting Time zone O Daylight saving pate 2073 Jj J0 tm 7 A tsian ome 2053 Pf E mme Jl A tenaz nad SES em HME romat Date format YYYY MM DD Time format 24Hrs NTP server address tw pool ntp org Host name or IP address a dd Current Camera Time Displays the current date and time on the camera Time Settings Synchronize with NTP Server Select this option to synchronize the date and time with a NTP server Synchronize with Computer Time Select this option to synchronize the date and time to the computer connected to the camera Manually Setting Select this option to manually configure the date and time Time Zone Select the time zone relevant to your location in the drop down list Daylight Saving Select this option to enable daylight saving The Start End date and time for daylight saving can be manually configured in the text boxes beneath the option EA a Copyright O 2013 NEXCOM International Co Lt
57. ult button has been pressed for 1 4 seconds the camera will be re started and all the settings will be reverted to default except IP address If pressed for over 5 seconds the camera will be re started and all the settings will be reverted to default including IP address Reset Press to reset the camera NECOM DI O Pin Definition Waterproof Connector Description oe pee el ar y Lak TT Pro L dS FE Er eee mare ALM IN ALM IN Gasket t Tightening UDD collar e J j Waterproof i iy connector Main body Seal nut Strain relief EA a Copyright 2013 NEXCOM International Co Ltd All Rights Reserved NCr 302 VHR User Manual Chapter 1 Product Introduction NEXCOM Cable Wiring Description 1 Cable Installation Steps 2 Run the cable inside the wall mount bracket and out through the cable opening at the front 3 Press down the push lock mechanism and secure the camera onto the push lock Wire the network cables to the waterproof connector on the right and wire the line in line out DC 12V AV 24V DI O and other cables to the waterproof connector on the left Tighten the waterproof connector after all the cables are secured in place 4 Secure the camera onto the wall mount bracket using the two screws provided 5 Open the camera s top cover to access the wired cables Install the RJ45 connector to the Ethernet cable and plug it into the corres
58. word Used to configure the SNMPv3 password EA Copyright O 2013 NEXCOM International Co Ltd All Rights Reserved NCr 302 VHR User Manual Chapter 2 Camera Configuration Multicast The IP camera s video streams can be sent to a multicast IP address group for one to many streaming The multicast settings for the IP camera can be configured in this page Multicast Settings Enable multicast Group address Stream 1 RTP Port RTCP Port Path rtsp 192 168 1 103 554 multicast stream1 Always multicast Stream 2 RTP Port 51002 RTCP Port 51003 Path risp 192 168 1 103 6556 multicast stream 2 C Always multicast Stream 3 RTP Port 51004 Path rtsp 192 166 1 103 6555 multicast stream3 C Always multicast Audio RTP Port 51006 RTCP Port 151007 RTF and RTCP Port Range 1025 65535 Tr e Range 1 255 RTCP Port 151005 Settings Enable Multicast Enables or disables multicast streaming Group Address Configures the IP address of the multicast group RTP Port Configures the RTP port of the multicast address this port is used for streaming video and audio data RTCP Port Configures the RTCP port of the multicast address this port is used for controlling RTP streams Path Configures the URL address of the video stream Always Multicast Check this option to enable the video stream to start multicast streaming without using RTCP Audio RTP Port and RTCP Port

Intelligent Digital Security IP Camera NCr-302

Contents

Download Pdf Manuals

Related Search

Related Contents