2-CHANNEL SATA II PCI EXPRESS CARD User Manual
Contents
1. 2 CHANNEL SATA PCI EXPRESS CARD User Manual Features and Benefits Compliant with one lane 2 5Gb s PCI Express specification Compliant with Serial ATA 1 0 specification Supports Serial ATA Generation 2 transfer rate of 3 0Gb s Supports Native Command Queue NCQ on SATA ports Provides three independent channels to connect two SATA and one PATA hard disk drive Supports up to UDMA6 transfer mode of PATA Supports up to 4 storage device connection Supports RAID 0 1 0 1 and JBOD functions Supports Windows 7 Vista XP and 2000 Connectors 2 x internal SATA connectors 2 x external eSATA connectors 1 x PATA connector Package Contents 1x PCle SATA 300 PATA Raid Card e 1x Manual 1x Driver CD e 2x SATA Data Cable 2x SATA Power Cable e 1x ATA 133 IDE Cable System Requirements e Windows 2000 Windows XP 2003 Vista 32 64 bit PCI Express enabled system with an available PCI Express slot Hardware Description External SATA Ports CON 1 amp CON2 Internal SATA Ports CON 3 amp CON4 Ultra ATA Connector Jumper Settings J1 J4 Enable CON1 or CONS Default CON1 J5 J8 Enable CON2 or CON4 Default CON2 D owes wm 1 2 close eu cu SATA CON1 2 3 close Enable Enable SATA CONS CON3 1 2 close Enable SATA CON2 2 3 close Enable SATA CONA Hardware Installation Turn Off the power to your computer Unplug the power cord and remove your computer2. As the BIOS boots press Ctrl J when prompted to enter the RAID BIOS At the next screen select Create RAID Disk Drive press Enter Enter RAID name press Enter Please use arrow keys and to switch the RAID level 7 to 1 Mirror then press Enter 5 Please use arrow keys 1 and to switch the disk use the space key to mark the selected disk then press Enter 6 Input the RAID size press Enter 7 When asked Created RAID on the select HDD Y N press Y to accept 8 At the next screen select Save And Exit Setup press Enter When asked Save to disk amp Exit Y N press Y to exit the BIOS CONCATENATION JBOD 1 As the BIOS boots press Ctrl J when prompted to enter the RAID BIOS 2 At the next screen select Create RAID Disk Drive press Enter 3 Enter RAID name press Enter 4 Please use arrow keys and to switch the RAID level to JBOD Concatenate then press Enter 5 Please use arrow keys and to switch the disk use the 8 space key to mark the selected disk then press Enter Input the RAID size press Enter When asked Created RAID on the select HDD Y N press Y to accept At the next screen select Save And Exit Setup press Enter When asked Save to disk amp Exit Y N press Y to exit the BIOS RAID 0 1 Striping Mirroring 1 As the BIOS boots press Ctrl J when prompted to enter the RAID BIOS At the next screen select Create RAID Disk Drive press Ente
3. 32 64bit 1 Setup the RAID Array prior to driver installation and boot up to Windows 2 At the Found New Hardware Wizard window pop up please click Cancel button to cancel the driver installation for the device at this moment The driver for this device will be installed in the next step 3 Please insert the CD driver bound with PCle SATA 300 PATA Raid Card into your CD ROM Drive 4 At the Windows desktop click Start then Run 5 Type D DS 30103 Windows Setup exe click OK Change D to match your CD ROM drive letter 6 Follow the on screen instructions to complete the installation 7 Restart Windows to complete the installation 15 To Verify Driver Installation Click on the Device Manager tab in System Properties which you access from the Windows Control Panel You should see an JMicron JMB36X RAID Controller installed under SCSI and RAID controllers Storage controllers Vista item
4. disk 1 Setup the RAID Array prior to Windows installation 2 Follow Microsoft s Windows installation procedure 3 Atthe Windows Setup screen press F6 to install the RAID driver 4 When prompted press S to specify the location of the driver 5 Insert the floppy disk then press Enter 6 Choose the proper item to fit the OS an RAID controller you are installing Each item shows the matched OS for it 13 7 Press Enter to finish driver installation then follow the on screen instructions to complete the Windows installation For Windows Vista 32 64 bit A new installation requires a floppy disk for the driver installation To create a pre install disk for 32 bit Vista copy the contents of the DS 30103 Windows Floppy32 folder found the driver CD onto a blank floppy disk To create a pre install disk for 64 bit Vista copy the contents of the DS 30103Windows Floppy64 folder found on the driver CD onto a blank floppy disk 1 Setup the RAID Array prior to Windows installation 2 Follow Microsoft s Windows installation procedure 3 At the Windows Setup screen press Load Driver to install the driver 4 Insert the floppy disk please select JMicron JMB36X Controller A jraid_f inf then press Next Change A to match your floppy drive letter 14 5 Follow the on screen instructions to complete the Windows installation For An Existing Installation For Windows 2000 XP 2003 32 64bit Vista
5. including the correct drive connection information will be written to the replacement disk Rebuild Mirror Drive When a failure to one member occurs you will be notified by the RAID BIOS during boot The steps below will guide you in rebuilding a failed mirror set 1 Replace he failed drive s with one of equal or greater capacity then start the computer 2 During boot press Ctrl J to enter the RAID BIOS 3 Select Rebuild Mirror Drive press Enter 4 Please use arrow keys and select the array you want to rebuild press Enter 5 Please use arrow keys and to select the destination disk press Enter 6 When rebuilding is finished select Save And Exit Setup press Enter When asked Save to disk amp Exit Y N press Y to exit the BIOS BIOS Configuration The PCle SATA II 300 PATA Raid Card BIOS will appear every time your system starts up During this POST process the BIOS will show up and indicate the devices attached to it Driver Installation For New Installation For Windows 2000 XP 2003 32 64bit A new installation requires a floppy disk for the driver installation To create a pre install disk for 32 bit Win2K WinXP Win2003 the contents of the DS 30103Windows Floppy32 folder found on the driver CD onto a blank floppy disk To create a pre install disk for 64 bit WinXP Win2003 copy the contents of the DS 30103Windows Floppy64 folder found on the driver CD onto a blank floppy
6. r Enter RAID name press Enter Please use arrow keys and to switch the RAID level to 01 Stripe Mirror then press Enter Please use arrow keys and to select chunk size from 9 4K 8K 16K 32K 64K or 128K then press Enter 6 Input the RAID size press Enter 7 When asked Created RAID on the select HDD Y N press Y to accept 8 At the next screen select Save And Exit Setup press Enter When asked Save to disk amp Exit Y N press Y to exit the BIOS Delete RAID Disk Drive 1 Asthe BIOS boots press Ctrl J when prompted to enter the RAID BIOS 2 At the next screen select Delete RAID Disk Drive press Enter 3 Please use arrow keys and select the array you want to delete use the space key to mark the selected array then press DEL 4 When asked ALL DATA ON THE RAID WILL LOST ARE YOU SURE TO DELETE Y N press Y to accept Solve Mirror Conflict When a RAID set is created then metadata written to the disk includes drive connection information If after a disk failure the replacement disk was previously part of a RAID set or used in another system it may have conflicting metadata If so this will prohibit the RAID set from being either created or rebuilt in order for the RAID set to function properly this old metadata must be first overwritten with the new metadata To resolve this from the main BIOS window select Solve Mirror Conflict then press Enter the correct metadata
7. s cover Remove the slot bracket from an available PCle slot Ae SAM qeu To install the bard carefully align the card s bus connector with the selected PCle slot on the motherboard Push the board down firmly 5 Attach your internal or external devices to the PCle SATA 300 PATA Raid Card Replace the slot bracket s holding screw to secure the card Replace the computer cover and reconnect the power cord 5 RAID Arrays RAID Arrays are setup in the PCle SATA 300 PATA Raid Card s BIOS There are four configurations supported RAID level Type Configurations Number of disks needed RAID 0 Disk Striping 20r3or4 RAID 0 1 Disk Striping Mirroring RAID 0 Striping 1 As the BIOS boots press Ctrl J when prompted to enter the RAID BIOS 2 At the next screen select Create RAID Disk Drive press Enter 3 Enter RAID name press Enter 4 Please use arrow keys and to switch the RAID level 6 to 0 Stripe then press Enter Please use arrow keys and to switch the disk use the space key to mark the selected disk then press Enter Please use arrow keys and to select chunk size from 4K 8K 16K 32K 64K or 128K then press Enter Input the RAID size press Enter When asked Created RAID on the select HDD Y N press Y to accept At the next screen select Save And Exit Setup press Enter When asked Save to disk amp Exit Y N press Y to exit the BIOS RAID 1 Mirroring 1
Download Pdf Manuals
Related Search