SeeTool - Solutions for KNX
Contents
1. Technical specifications Group addresses Address Name proposal Function WANA Room 001 Light On Off Light on off by the light controller 1 1 2 Room 001 Light Dimming Light dimming up down by the light controller 1 1 3 Room 001 Light Value Light absolute value by the light controller 1 1 4 Room 001 Light Status switch Feedback from actuator On Off 1 1 5 Room 001 Light Status value Feedback from actuator 0 100 1 1 6 Room 001 Light Resulting actual value Measured lux value by light controller corrected value 1 1 7 Room 001 Light Lux value setting Different lux values from push button 1 1 8 Room 001 Light Permanent OFF 0 Permanent OFF movement detector disabled 1 1 9 Room 001 Light Feedb operation Indication permanent off 0 and mode automatic regulation 1 2 1 2 Room 001 Cooling control value Cooling 0 100 sent by the room temperature controller to the heating actuator 2 1 3 Room 001 Comfort Standby mode Change between comfort 1 and standby 0 mode ry settings Application 8 8 0 0 0 4 ly Movement dependent automatic light control with light regulation and manual control temperature control cooling with thermo electric valve drive 230V single room Technical specifications Actual value correction The measured brightness value actual value can be corrected A distinction is drawn here between the installati on location of the presence detecto2. Application 8 8 0 0 0 4 Movement dependent automatic light control with light regulation and manual control temperature control cooling with thermo electric valve drive 230V single room Technical specifications Note Number of controlled electronic interfaces highly depends on used ones check with manufacturer recommenda tions An electronic interface takes high inrush current It is recommended that Type C MCB s Miniature Circuit Breaker s are used Using Type B leads to decreased number of units settings Configuration The ETS tool is used to set the parameters for the devices in the application and to define the functional relationship between the devices by group addresses The following parameters and group address relations must be set and assigned The parameters should be set first and in the described order The parameters which can be changed to fine tune the application are described further on KNX Argus presence with light control KNX Push button 2 gang with RTC 12 Switch object 1 Block 2 1 bit gt 2 1 3 0 Object A PB 1 2 byte gt 1 1 7 60 Switch output Closed loop 1 bit gt VW 3 ObjectA PB 2 2 byte gt 1 1 7 61 Dimming output Closed loop 4 bit gt 1 1 2 6 Object A PB3 2 byte gt 1 1 7 62 Setpoint 1 Closed loop 1 byte gt 1 1 3 9 Value objectA PB4 1 byte gt 1 1 8 64 Fb operat mode Closed loop 1 bit gt 11 9 11 Status feedb
3. Movement dependent automatic light control with light regulation and manual control temperature control cooling with thermo electric valve drive 230V single room Technical specifications Fine tuning The delay time for changing between standby comfort is dependent on presence activity in a room To save energy the switch over from standby to comfort is done when movement is detected after a specified dead time Then a staircase timer is started which will be retriggered by every detected movement If no movement is detected the staircase timer will run out and standby mode is activated again Parameter page Parameter Value Block 2 general gt Movement sensors Dead time Time base 1s 1 min 1 min Block 2 general gt Movement sensors Dead time Time factor 1 255 3 Block 2 general gt Times Time base for staircase timer 1s 1 min 1h 1 min Block 2 general gt Times Time factor for staircase timer 1 255 25 KNX Push button 2 gang with room temperature control unit Push buttons The end user can select brightness level lux value with push button 1 2 and 3 These values can be changed with the parameters of the push buttons Parameter page Parameter Value Push button 1 edges values Value 1 basis factor 500 lux Basis 0 01 327 68 0 32 Push button 1 edges values Factor 0 2047 1562 Push button
4. A ate a EL sl ject PB 4 1 bit 1 1 9 70 Value input Closed loop 1byte lt 1 1 8 opiece pi j eae ae a eal 47 fort input trol 1 bit 2 1 71 Lux value setting Closed loop 2 byte lt 1 1 7 Comfotinpu Conto bi SRN a a E Se 65 Correcting 107 Result act value Send 2 byte gt a variable cooling gt 2 1 2 optional basic level Control 1 byte 109 Status feedback Safety pause 1 bit lt 1 1 4 Push button 4 110 Status feedback Brightness 1 byte lt 1 1 5 Select push button function Edges with 2 byte General values Actual value correction enable Actual value 0 2000 Lux installation site Push button 1 edges values Lamp switched off Value 1 basis factor 500 Max brightness of lamp EEES Basis possible Actual value 0 2000 Lux reference surface values in brackets 0 32 0 to 655 04 Lamp switched off Factor 0 2047 1562 Max brightness of lamp Push button 2 Optional to check PoS after download Select push button Send actual value cyclically function Edges with 2 byte reference surface enable values Time base send lux value is Time factor send lux value 60 Push button 2 edges values F z Value 1 basis factor 300 Block configuration p r ee fatal aisela Basis possible Aan PERR ae a ms e values in brackets 0 16 0 to 327 52 love presence block 2 enable Factor 0 2047 1875 Light control enable Push Block 2 general gt Movement sensors esnbution 3 Sect Ne Ia bl Select push button eo oronen a S S
5. as parameters in ETS Parameter page Parameter Value General Actual value installation site Lamp 0 2000 lux switched OFF General Actual value installation site Max 0 2000 lux brightness of lamp 100 General Actual value reference surface Lamp 0 2000 lux switched OFF General Actual value reference surface Max 0 2000 lux brightness of lamp 100 Application 8 8 0 0 0 4 Movement dependent automatic light control with light regulation and manual control temperature control cooling with thermo electric valve drive 230V single room Technical specifications Fine tuning Some parameters can be changed to fine tune the solution to the building and specific requirements Parameter which may need to be adjusted are listed below our recommendation in brackets KNX ARGUS presence detector with light control and IR receiver The staircase timer delay time will be retriggered by every detected movement when the light is on The light will be dimmed down to minimum if no movement has been detected within the specified time fine tuning If no movement is detected the light will stay on minimum level for a time period specified by the parameter dimming down time After this time the light will be switched off Parameter page Parameter Value General light control gt Time base for staircase timer 1s 1 min 1h 1 min Control response in automatic mode gt Times Gener
6. 2 edges values Value 1 basis factor 300 lux Basis 0 01 327 68 0 16 Push button 2 edges values Factor 0 2047 1875 Push button 3 edges values Value 1 basis factor 100 lux Basis 0 01 327 68 0 08 Push button 3 edges values Factor 0 2047 1250 Note Temperature controller parameter pages uses the unit Kelvin s K for relative temperatures and Cel sius C degrees for absolute temperatures 1K 1 C Room temperature controller Default setpoints for cooling depends on presence in a room Parameter page Parameter Value Control general gt Setpoints Cooling setpoint for comfort 5 40 C 24 C Control general gt Setpoints Cooling setpoint for standby 5 40 C 26 C The user is allowed to adjust the default setpoint within specified limits Parameter page Parameter Value Control general Max upper setpoint adjustment 0 10 K 3 K Control general Max lower setpoint adjustment 0 10 K 3 K ry fine tuning 10 Application 8 8 0 0 0 4 Movement dependent automatic light control with light regulation and manual control temperature control cooling with thermo electric valve drive 230V single room Technical specifications Fine tuning Value correction of measured temperature The temperature in the room is measured by the internal temperature sensor in the room temp
7. NX Control Unit 0 10V REG K 1 gang with manual mode MTN630919 KNX ARGUS Presence with light control and IR receiver MTN645129 KNX Heating actuator REG K 6x230 0 05A MTN639125 KNX Thermoelectric valve drive 230V here for cooling purposes Design ranges Frames not included Other designs and colours available EXXACT WDE002939 KNX PB 2 gang with room temperature control unit Installation The presence detector is intended for ceiling mounting in a size 60 mounting box It can also be mounted to ceilings using the surface mounting housing for ARGUS Presence art no MTN550619 JAN functions Application 8 8 0 0 0 4 ly Movement dependent automatic light control with light regulation and manual control temperature control cooling with thermo electric valve drive 230V single room Technical specifications Wiring diagram f KNX KNX Push button 2 gang ARGUS Presence with room temperature _ with light control control unit w and IR receiver WDE002939 i MTN630919 Temperature control System component Lighting control Presence detection KNX KNX f AAO ee KNX Control unit 0 10 V ssisieissiee Heating actuator e REG K 1 gang i REG K 6x230 0 05 A with manual mode MTN645129 MTN647091 Manual control 5 Power supply L N Thermoelectric j valve drive 230 V MTN639125 here for cooling things work together
8. SeeTool Solutions for KNX Office building segment Application 8 8 0 0 0 4 Movement dependent automatic light control with light regulation and manual control temperature control cooling with thermoelectric valve drive 230V single room Schneider Application 8 8 0 0 0 4 fly Movement dependent automatic light control with light regulation and manual control temperature control cooling with thermo electric valve drive 230V single room Lighting and temperature control functions Lighting control functions The lights are automatically switched ON or OFF dependant on people s movement and existing brightness When the lights are on the light controller in the presence detector maintains the decided lux set point by dimming the lamp actuator dependant on the available daylight In addition three predefined light levels and a permanent OFF can be activated manually by push button Temperature control functions Temperature controller tries to keep room temperature at it s setpoint by controlling thermoelectric valve drives 230V for cooling via a KNX heating actuator The movement detection will automatically set the temperature control either into comfort or standby mode Application areas Lighting The application is defined to be used in office rooms and or conference rooms where the level of light will be kept constant taking into account the amount of natural light The solution offers sophisticated control
9. al light control gt Time factor for staircase timer 1 255 25 Control response in automatic mode gt Times General light control gt Time base dimming down time 1 s 1 min 1 h 1 min Switching off in automatic mode General light control gt Time factor dimming down time 1 255 5 Switching off in automatic mode Delay time Time base x Time factor Dimming down time Time base x Time factor Lux level setpoint in reference area Parameter page Parameter Value General light control gt l Nominal value reference surface 10 2000 lux 600 lux Control response in auto mode gt Brightness General light control gt l Hysteresis 10 50 20 Control response in auto mode gt Brightness The actual brightness value corrected measured value can be sent cyclically to the bus via communication object 107 This can be used for test purpose together with ETS If it is used for other purposes the value should not be sent too often for bus load reasons If there is no receiver to display the value in the project the function should be disabled after the test phase Parameter page Parameter Value General Send actual value cyclically reference enable disable disable surface General Time base send lux value 1s 1 min 1 h 1 min General Time factor send lux value 1 255 30 Cycle time Time base x Time factor Application 8 8 0 0 0 4
10. amp System if required through the open technology communication network va idated Application 8 8 0 0 0 4 Movement dependent automatic light control with light regulation and manual control temperature control cooling with thermo electric valve drive 230V single room Technical specifications Functions Lighting control The lights are automatically switched ON when a person enters the room and the brightness value is below the selected brightness threshold If no movement is detected within a delay time of 25 minutes the light will be dimmed down to minimum If no movement is detected for another 5 minutes the light will be switched off When the lights are on the light controller in the presence detector maintains the decided lux set point by sending dimming telegrams to the lamp actuator If the daylight will increase the regulation dims down the artificial light If it decreases the regulation will dim up the artificial light The lux set point after download and power failure is adjustable by ETS software The default lux setpoint at the reference surface e g desk is 500 lux 20 hysteresis The user can also select the lux setpoint by the push button unit Button 1 will give high brightness 500 lux button 2 will give medium brightness 300 lux and button 3 low brightness 100 lux With button 4 permanent OFF can be activated The light will then be off until one of the other buttons is pressed When perm
11. anent OFF is activated the status LED next to the button is blinking Temperature control Temperature controller tries to keep room temperature at it s setpoint by controlling valves Cooling is controlled by a thermoelectric valve drive 230V via a KNX heating actuator Movement detection will automatically set the temperature control into comfort mode To save energy this will not happen until a person has been in the room for more than 3 minutes In this way the temperature control is not affected if someone is present in the room just for a short period of time If no movement is detected within a delay time of 25 minutes the temperature control is set into standby mode Comfort mode default room temperature setpoint 24 C Standby mode default room temperature setpoint 26 C The setpoint can be adjusted by the user 3 C from given setpoint This is done by pushing invisible buttons on both sides of the display frame my functions Application 8 8 0 0 0 4 Movement dependent automatic light control with light regulation and manual control temperature control cooling with thermo electric valve drive 230V single room Technical specifications Components Application consists of one presence detector one DIN rail 0 10V control unit mounted in the cabinet or close to the room and one room temperature controller with buttons one heating actuator and one thermoelectric valve drive 230V MTN647091 K
12. e ings emane function Edges with 2 byte Dead time beginning of movement enable waltiee Time base 1 min Time factor 3 Push button 3 edges values Value 1 is factor 100 Block 2 general gt Brightness Sat o actor Mo emendacion brigniness values in brackets 0 08 0 to 163 76 independ Factor 0 2047 1250 Block 2 general gt Time Time base for staircase timer 1 min Time factor for staircase timer 25 Application 8 8 0 0 0 4 Movement dependent automatic light control with light regulation and manual control temperature control cooling with thermo electric valve drive 230V single room Technical specifications Configuration KNX Argus presence with light control KNX Push button 2 gang with RTC General light control Push button 4 Automatic at object value 0 Select push button Memory behaviour parameterised function Switching setpoint value Object A 1 byte in steps 0 100 Extended controller Value 0 parameters enable Trigger status LED Flashes when status General light control gt feedback object Control response in automatic mode gt cuele setti ngs Times Control general Time base for staircase timer 1 min Use control Yes Time factor for staircase timer 25 Controller type Cooling 7 Duration of comfort extension None General light control gt Setpoint adjustment maintained Control response in automatic mode gt after change in operation mode ae Brig
13. erature controller The actual temperature is shown in the display If the value is not representative for the room it is possible to adjust it by parameter Actual temperature measured temperature adjustment value cooling Control general gt Control cooling Reset time for cooling in min Parameter page Parameter Value Control general gt Actual Correct internal actual temperature 0 temperature resultant factor 128 127 0 1 K Parameters for tuning cooling control Xp and Ti Parameter page Parameter Value Control general gt Control Proportional range for cooling in 0 1K 10 255 40 1 255 min 20 Power failure behaviour Behaviour when bus voltage fails relay no Light is OFF Behaviour when bus voltage returns switch off relay Light is OFF JAN fine tuning 11 Application 8 8 0 0 0 4 Movement dependent automatic light control with light regulation and manual control temperature control cooling with thermo electric valve drive 230V single room Technical specifications User manual The user manual provided for the application is an end users training material and can be installed at site when final submission is made Please do no forget to cut out this quick guide for the user and attach to the wall next to the entrance to the room Also make sure the customer is aware of the installed applications function Quick guide This room is equipped with a m
14. htness Nominal value 10 2000 Lux Control general gt Actual temperature reference surface 500 resultant Hysteresis 10 50 20 Correct internal actual temperature factor 128 127 0 1 K 0 General light control gt Switching off in automatic mode Time base dimming down time 1 min Control general gt Control cooling Time factor dimming down time 5 Select cooling system Adjustment via control parameter Proportional range for NOTE See description fine tuning KNX Control unit 0 10V REG K 1 gang cooling in 0 1 K 10 255 40 1 1 1 gt 0 Switch object Channeli 1 bit Reest fimo tar cecling 255 mini eae 1 1 2 gt 1 Dimming object Channel 1 4 bit KNX Heating actuator 1 1 33 gt 2 Value object Channel 1 1 byte 2 1 2 gt 0 Output 1 Control value 1 byte 1 1 4 lt 8 Status feedb switch Channel 1 1 bit General Cyclic time PWM of outputs 2 minutes 1 1 5 lt 9 Status feedb value Channel 1 1 byte Output 1 NOTE The read flag R must be set Type of control value 1 byte 1 General Status switch active status resp object Status value object active status resp object 1 Dimming time reduction Set 0 dimming time reduction for value telegram at 6 Application 8 8 0 0 0 4 Movement dependent automatic light control with light regulation and manual control temperature control cooling with thermo electric valve drive 230V single room
15. ing with thermo electric valve drive 230V single room Technical specifications User manual Quick guid This room is equipped with a move ment dependent automatic light control with light regulation and manual control temperature control Automatic mode operation invisible buttons Temperature control cooling Movement detection will automatically set Jie the temperature control into comfort Fer mode To save energy this will not happen F until a person has been in the room for more than 3 minutes In this way the temperature control is not affected if someone is present in the room just for a short period of time If no movement is detected within a delay time of 25 minutes the temperature control is set into standby mode Comfort mode default room temperature set point 24 C Standby mode default room temperature set point 26 C The set point can be adjusted by the user 3 C from given set point This is done by pushing invisible buttons on both sides of the display frame service Schneider foryour 06 10 Application 8 8 0 0 0 4 amp Electric cu st omer ISC02093_EN 13
16. of the lighting and cooling with an automatic movement detector and additional manual control plus an open window sensing function to set temperature at comfort and standby mode gt Energy savings gt Flexibility Temperature Combining the presence and daylight For optimized costs the device s functional function with temperature control to the interaction is predefined Functionality can room application we are able to utilize the be modified or changed at any time in the daylight and temperature factors to optimize lifecycle and allows a maximum of flexibility and save energy during the active period of and adaptation when walls are removed and use throughout the year Presence depen rooms combined dant lighting control plus daylight harvesting can achieve a 65 electricity saving compared to installations without automatic function At temperature side presence gt dependant control can lead to savings of up Reliabil ity EN 15232 to 25 yearly in compare to rooms without automatic control functions Design planning and installation documents A class solution are pre defined which makes the entire building process faster and more reliable User documents and descriptions are prepared to assist in user training The gt Future proof application works as an individual stand alone room control unit or combined with the The application is prepared and defined for entire network integration into a Building Management tested
17. ove ment dependent automatic light control with light regulation and manual control temperature control Automatic mode operation Lighting control The lights are automatically switched ON when a person enters the room and the brightness value is below the selected brightness threshold If no movement is detected within a delay time of 25 minutes the light will be dimmed down to minimum If no move ment is detected for another 5 minutes the light will be switched off When the lights are on the light controller in the presence detector maintains the decided lux set point by sending dimming telegrams to the lamp actuator If the daylight will increase the regulation dims down the artificial light If it decreases the regulation will dim up the artificial light Manual mode operation The user can also select the lux set point by the pushbutton unit Button 1 will give high brightness 500 lux button 2 will give medium brightness 300 lux and button 3 low brightness 100 lux With button 4 permanent OFF can be activated The light will then be off until one of the other buttons is pressed When permanent OFF is activated the status LED next to the button is blinking service Schneider foryour 06 10 Application 8 8 0 0 0 4 BF Electric cu st omer 12 Application 8 8 0 0 0 4 Movement dependent automatic light control with light regulation and manual control temperature control cool
18. r and the reference area a desk surface for example The brightness value of the reference area is determined with the aid of actual value correction and taking the brightness value measured by the presence detector at the installation location and an internal adjustment curve into account In the case of light regulation it is not the brightness value at the installation location which is important but the brightness value at the reference area desk For actual value correction you will need a luxmeter example Roline TES 1335 or equivalent Four measurements are required for actual value correction setti ngs e With the artificial lighting switched OFF brightness is measured at the presence detector installation location e With the artificial lighting switched OFF brightness is measured at the reference area desk for example e With the artificial lighting switched ON maximum brightness brightness is measured at the presence detector installation location e With the artificial lighting switched ON maximum brightness brightness is measured at the reference area desk for example The measurements can be done in daylight but not in clear sunshine best condition is cloudy weather To switch ON to maximum brightness a value telegram 100 can be sent from ETS to the value object of the control unit for example Note the presence detector should not be in operation at this time The four lux values measured must be entered
Download Pdf Manuals
Related Search