USER MANUAL - Full Compass
Contents
1. Network IP Setup IP Address 192 168 1 39 Subnet Mask 255 255 255 0 Default Gateway 192 168 1 1 Figure 12 The Network Tab To change the IP parameters 1 Click on the Network tab The window shown in Figure 12 is displayed 2 Modify the IP address subnet mask and default gateway addresses as required 3 Click Apply The changes are made and the message shown in Figure 13 is displayed Warning Reboot for new settings to take effect Figure 13 Warning Message VA 1USB T VA 1USB R Using the Web Pages 4 Reboot the device by clicking on Utilities and clicking Reboot The device is rebooted with the new IP parameters 6 4 The Functions Tab Using the Functions tab Figure 14 you can enable disable and modify the serial over IP parameters System Network Functions Serial over IP 7 Enable Serial over IP Baudrate Setting for Type 2 Baudrate 115200 Data bits 8 Parity None Stop bits 1 X Apply Figure 14 The Functions Tab To modify the serial over IP functionality 1 Click on the Functions tab The window shown in Figure 14 is displayed 2 Enable or disable the device by checking or unchecking the Enable Serial over IP box 3 Modify the serial communication parameters using the drop down lists for Baud rate Data bits Parity and Stop bits 4 Click Apply The changes are made and the message shown in Figure 15 is displayed 165 VA 1USB T VA 1USB R Usi2. Figure 16 TP Pinout Wiring oon A OOONN Introduction Welcome to Kramer Electronics Since 1981 Kramer Electronics has been providing a world of unigue creative and affordable solutions to the vast range of problems that confront video audio presentation and broadcasting professionals on a daily basis In recent years we have redesigned and upgraded most of our line making the best even better Our 1 000 plus different models now appear in 11 groups that are clearly defined by function GROUP 1 Distribution Amplifiers GROUP 2 Switchers and Routers GROUP 3 Control Systems GROUP 4 Format Standards Converters GROUP 5 Range Extenders and Repeaters GROUP 6 Specialty AV Products GROUP 7 Scan Converters and Scalers GROUP 8 Cables and Connectors GROUP 9 Room Connectivity GROUP 10 Accessories and Rack Adapters and GROUP 11 Sierra Video Products Thank you for purchasing the Kramer MegaTOOLS VA 1USB T USB Transmitter and VA 1USB R USB Receiver which are ideal for e Presentation and multimedia applications e Long range USB distribution for schools hospitals stores and security installations Each package includes the following items e VA 1USB T USB Transmitter and VA 1USB R USB Receiver e 2 Power adapters 5V DC e IR Blaster cable e This user manual VA 1USB R Introduction 2 1 Getting Started We recommend that you e Unpack the equipment carefully and save the original box and packaging
3. materials for possible future shipment e Review the contents of this user manual Go to http www kramerelectronics com support product_downloads as to check for up to date user manuals application programs and to check if firmware upgrades are available where appropriate Achieving the Best Performance To achieve the best performance e Use only good quality connection cables we recommend Kramer high performance high resolution cables to avoid interference deterioration in signal quality due to poor matching and elevated noise levels often associated with low quality cables e Do not secure the cables in tight bundles or roll the slack into tight coils e Avoid interference from neighboring electrical appliances that may adversely influence signal quality e Position your Kramer VA 1USB T and VA 1USB R away from moisture excessive sunlight and dust This equipment is to be used only inside a building It may be connected only to other equipment that is installed inside a building VA 1USB T VA 1USB R Getting Started 2 2 2 3 2 4 Safety Instructions Caution No operator serviceable parts inside the unit Warning Use only the Kramer Electronics input power wall adapter that is provided with the unit Warning Disconnect the power and unplug the unit from the wall before installing Recycling Kramer Products The Waste Electrical and Electronic Equipment WEEE Directive 2002 96 EC aims to reduce the
4. IR transmitter USB DEVICES 1 4 Connect to up to four USB devices kl A D eA Connectors Button Press to establish the TP link to the transmitter LINK Lights green when the TP link to the transmitter is established 5 ONLED Lights green to indicate that the device is powered on Figure 4 defines the rear panel of the VA 1USB R MACHINE ID 5V DC CATS 6 IN Figure 4 VA 1USB R USB Receiver Rear Panel CAT 5 6 IN RJ 45 Connect to the CAT 5 6 OUT RJ 45 connector on the rear panel of Connector the VA 1USB T see Section 2 4 7 RS 232 9 pin D sub Connect to the device to be controlled via the serial link Serial Port Connector F Note The RS 232 link is bidirectional MACHINE ID 4 way Use to setthe device ID to pair with the transmitter see DIP switch Section 5 2 5V DC Power Connector Connect to one of the supplied 5V DC power adapters Center pin positive VA 1USB T VA 1USB R Defining the VA 1USB T and VA 1USB R USB Transmitter and a Receiver ji 5 Connecting the VA 1USB T and VA 1USB R Switch off the power to all devices before connecting them to your VA 1USB T VA 1USB R After connecting your VA 1USB T VA 1USB R connect the power to the transmitter and receiver and then switch on the power to the other devices LL e e VA 1USB T Q _ i Multimedia USB Flash Hard Drive Player Storage Figure 5 Connecting the VA 1USB T Transmitter and VA 1USB R Receiver VA 1USB T VA 1
5. amount of WEEE sent for disposal to landfill or incineration by requiring it to be collected and recycled To comply with the WEEE Directive Kramer Electronics has made arrangements with the European Advanced Recycling Network EARN and will cover any costs of treatment recycling and recovery of waste Kramer Electronics branded equipment on arrival at the EARN facility For details of Kramer s recycling arrangements in your particular country go to our recycling pages at htto www kramerelectronics com supportrecycling Shielded Twisted Pair Unshielded Twisted Pair We recommend that you use Shielded Twisted Pair STP cable and stress that the compliance to electromagnetic interference was tested using STP cable There are different levels of STP cable available and we advise you to use the best quality STP cable that you can afford For the VA 1USB T and VA 1USB R pair we recommend the use of shielded twisted pair STP non skew free Kramer BC STP cable Overview The VA 1USB T and VA 1USB R are a high performance TP Twisted Pair transmitter and receiver for communicating USB bidirectional RS 232 data and unidirectional IR signals over extended distances using CAT 5 6 cable The VA 1USB T encodes USB signals and RS 232 data and transmits them over CAT 5 6 cable as a TP signal The VA 1USB R decodes the signal from the TP into USB signals and RS 232 data The VA 1USB R also acts as a 4 port USB hub and receives IR signal
6. repair of any defective parts within a reasonable period of time free of any charge for the necessary parts and labor to complete the repair and restore this product to its proper operating condition Kramer Electronics will also pay the shipping costs necessary to return this product once the repair is complete 2 Replace this product with a direct replacement or with a similar product deemed by Kramer Electronics to perform substantially the same function as the original product 3 Issue a refund of the original purchase price less depreciation to be determined based on the age of the product at the time remedy is sought under this limited warranty What Kramer Electronics will not do Under This Limited Warranty If this product is returned to Kramer Electronics or the authorized dealer from which it was purchased or any other party authorized to repair Kramer Electronics products this product must be insured during shipment with the insurance and shipping charges prepaid by you If this product is returned uninsured you assume all risks of loss or damage during shipment Kramer Electronics will not be responsible for any costs related to the removal or re installation of this product from or into any installation Kramer Electronics will not be responsible for any costs related to any setting up this product any adjustment of user controls or any programming required for a specific installation of this product How to Obtain a Remedy under this
7. to the receiver is established ON LED Lights green when the device is powered on VA 1USB T VA 1USB R Defining the VA 1USB T and VA 1USB R USB Transmitter and Receiver Figure 2 defines the rear panel of the VA 1USB T INPUT CAT5 6 OUT USB Host MACHINE ID 5V DC ii a Figure 2 VA 1USB T USB Transmitter Rear Panel Feature Function USB HOST INPUT Connect to a USB host see Section 5 Type B USB Connector 7 CAT 5 6 OUT RJ 45 Connect to the CAT 5 6 IN RJ 45 connector on the VA 1USB R Connector see Section 2 4 MACHINE ID 4 way Use to set the device ID to pair with the receiver see Section 5 2 DIP switch 5V DC Power Connector Connect to one of the supplied 5V DC power adapters Center pin positive 4 2 Defining the VA 1USB R USB Receiver The VA 1USB R decodes the USB signal and RS 232 data from the TP link sent from the VA 1USB T The receiver distributes the USB signal across four USB ports acting as a USB hub and outputs the RS 232 data The VA 1USB R receives an IR signal via its IR sensor and sends it over the TP link to the VA 1USB T Figure 3 defines the front panel of the VA 1USB R Receiver EN VA 1USB T VA 1USB R Defining the VA 1USB T and VA 1USB R USB Transmitter and USB DEVICES 1 2 3 4 unx ON a a A B USB Receiver VA 1USB R Figure 3 VA 1USB R USB Receiver Front Panel Feature Function IR Sensor Receives IR signals from an
8. 2 pin 3 to pin 3 and pin 5 to pin 5 need to be connected to the RS 232 9 pin D sub port on your PC Setting the Device ID DIP switch The Device ID DIP switch is used on both the VA 1USB T transmitter and VA 1USB R receiver to set matching device numbers This allows up to 16 pairs of transmitters and receivers to communicate independently on the same TP subnet Figure 6 Machine ID DIP switch Set each device in a transmitter and receiver pair to the same device ID according to the following table Press a switch up to turn it on and down to turn it off Switch Numba TERT ID o ot ot on ron or or s on on on on e on on on on 7 on on on On s on or on on e fon o or on VA 1USB T VA 1USB R Connecting the VA 1USB T and VA 1USB R Switch Number Device ID pit Jon ot on o m on fo or oF me on on for On ma on on on OF ris on on on On 5 3 Resetting the VA 1USB T to Factory Default Settings To reset the VA 1USB T to factory default settings 1 Turn off the power to the device 2 Press and hold the Reset button while turning on the power to the device 3 When the Link LED starts to flash release the Reset button The device is reset to factory default settings 5 4 Resetting the VA 1USB R to Factory Default Settings To reset the VA 1USB R to factory default settings 1 Turn off the power to the device 2 Press and hold the Link button while turning o
9. KRAMER ELECTRONICS LTD USER MANUAL MODELS VA 1USB T USB Transmitter VA 1USB R USB Receiver P N 2900 300209 Rev 3 TASET VA 1USB R USB Transmitter Receiver Auick Start Guide This guide helps you install and use your product for the first time For more detailed information go to o http www kramerelectronics com support product_downloads asp to download the latest manual or scan the Pr QR code on the left ave 1 Check what s in the box ef VA 1USB T USB Transmitter and VA 1USB R Receiver 4 1 Quick start guide 2 Power adapters 5V DC 2 1 IR Blaster Cable 8 Rubber feet Step 2 Install the VA 1USB T and VA 1USB R Mount the devices in racks using the optional RK T2B rack adapter available for purchase or attach the rubber feet and place them on shelves i VA 1USB R Rear Panel RS 232 MACHINE ID VDC a EJ 0000 Step 3 Connect the inputs and outputs Always switch off the power to all devices before connecting them to your VA 1USB T and VA 1USB R VA 1USB T Front Panel VA 1USB T kk ba Twisted Pair Pinout To RS 232 EIA TIA 5688 Controlled Device PIN Wire Color VA 1USB R Front Panel Orange White 1 R 2 1 4 Lax ON 3 O EES O 00 4 5 USB Receiver VA 1USB R 6 7 8 Step 4 Connect the power Connect the power adapters to the VA 1USB T and VA 1USB R and plug the ad
10. Limited Warranty To obtain a remedy under this limited warranty you must contact either the authorized Kramer Electronics reseller from whom you purchased this product or the Kramer Electronics office nearest you For a list of authorized Kramer Electronics resellers and or Kramer Electronics authorized service providers please visit our web site at www kramerelectronics com or contact the Kramer Electronics office nearest you In order to pursue any remedy under this limited warranty you must possess an original dated receipt as proof of purchase from an authorized Kramer Electronics reseller If this product is returned under this limited warranty a return authorization number obtained from Kramer Electronics will be required You may also be directed to an authorized reseller or a person authorized by Kramer Electronics to repair the product If itis decided that this product should be returned directly to Kramer Electronics this product should be properly packed preferably in the original carton for shipping Cartons not bearing a return authorization number will be refused Limitation on Liability THE MAXIMUM LIABILITY OF KRAMER ELECTRONICS UNDER THIS LIMITED WARRANTY SHALL NOT EXCEED THE ACTUAL PURCHASE PRICE PAID FOR THE PRODUCT TO THE MAXIMUM EXTENT PERMITTED BY LAW KRAMER ELECTRONICS IS NOT RESPONSIBLE FOR DIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY OR CONDITION OR UNDER ANY OTHER LEGAL
11. THEORY Some countries districts or states do not allow the exclusion or limitation of relief special incidental consequential or indirect damages or the limitation of liability to specified amounts so the above limitations or exclusions may not apply to you Exclusive Remedy TO THE MAXIMUM EXTENT PERMITTED BY LAW THIS LIMITED WARRANTY AND THE REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES REMEDIES AND CONDITIONS WHETHER ORAL OR WRITTEN EXPRESS OR IMPLIED TO THE MAXIMUM EXTENT PERMITTED BY LAW KRAMER ELECTRONICS SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE IF KRAMER ELECTRONICS CANNOT LAWFULLY DISCLAIM OR EXCLUDE IMPLIED WARRANTIES UNDER APPLICABLE LAW THEN ALL IMPLIED WARRANTIES COVERING THIS PRODUCT INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SHALL APPLY TO THIS PRODUCT AS PROVIDED UNDER APPICABLE LAW IF ANY PRODUCT TO WHICH THIS LIMITED WARRANTY APPLIES IS A CONSUMER PRODUCT UNDER THE MAGNUSON MOSS WARRANTY ACT 15 U S C A 2301 ET SEQ OR OTHER APPICABLE LAW THE FOREGOING DISCLAIMER OF IMPLIED WARRANTIES SHALL NOT APPLY TO YOU AND ALL IMPLIED WARRANTIES ON THIS PRODUCT INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR THE PARTICULAR PURPOSE SHALL APPLY AS PROVIDED UNDER APPLICABLE LAW Other Conditions This limited warranty gives you specific leg
12. TION MAXIMUM POWER OUTPUT 5V 500mA per USB port TRANSMISSION Up to 100m 328ft DISTANCE OPERATING 0 to 40 C 32 to 104 F TEMPERATURE STORAGE 40 to 70 C 40 to 158 F TEMPERATURE HUMIDITY 10 to 90 RHL non condensing DIMENSIONS 12 1cm x 7 18cm x 2 42cm 4 76 x 2 83 x 0 95 W D H WEIGHT 0 44kg 0 97lbs approx each INCLUDED 2 Power supplies ACCESSORIES OPTIONS RK T2B 19 rack adapter ecitications 9 Default Communication Parameters RS 232 VA 1USB T VA 1USB R Baud Rate 115200 Data Bits Stop Bits Parity Ethernet IP Address Network Mask Pt tga Default Gateway 192 168 1 1 or AA CD T A 4 ND gt ate Wie ae a i nim ES n are 20 VA 1USB T VA 1USB R Default Communication Parameters LIMITED WARRANTY The warranty obligations of Kramer Electronics for this product are limited to the terms set forth below Whatis Covered This limited warranty covers defects in materials and workmanship in this product What is Not Covered This limited warranty does not cover any damage deterioration or malfunction resulting from any alteration modification improper or unreasonable use or maintenance misuse abuse accident neglect exposure to excess moisture fire improper packing and shipping such claims must be presented to the carrier lightning power surges or other acts of nature This limited warranty
13. USB R Connecting the VA 1USB T and VA 1USB R To connect the VA 1USB T and the VA 1USB R as illustrated in the example in Figure 5 1 Onthe VA 1USB T connect The USB host for example a computer to the USB Host Input connector The RS 232 controller for example a laptop controller with an RS 232 interface to the RS 232 9 pin D sub connector An IR blaster to the IR 3 5mm mini jack 2 On the VA 1USB R connect The first USB Devices port to a USB hard drive The second USB Devices port to a multimedia player The fourth USB Devices port to a USB flash storage device 3 Using STP cabling connect the CAT 5 6 Out RJ 45 connector on the VA 1USB T to the CAT 5 6 In RJ 45 connector on the VA 1USB R see Section 2 4 4 Set the machine ID on both devices to the same ID using the Machine ID DIP switch see Section 5 2 5 Connect the power adapters to the power sockets on the VA 1USB T and VA 1USB R and plug the adapters into the mains electricity not shown in Figure 5 6 Establish a TP link by pressing the Link button on the receiver 5 1 5 2 10 Connecting to the product via RS 232 You can connect to the VA 1USB T VA 1USB R via an RS 232 connection using for example a PC Note that a null modem adapter connection is not required To connect to the VA 1USB T VA 1USB R via RS 232 e Connect the RS 232 9 pin D sub port on the VA 1USB T VA 1USB R via a 9 wire straight cable only pin 2 to pin
14. al rights and you may have other rights which vary from country to country or state to state This limited warranty is void if i the label bearing the serial number of this product has been removed or defaced ii the product is not distributed by Kramer Electronics or iii this product is not purchased from an authorized Kramer Electronics reseller If you are unsure whether a reseller is an authorized Kramer Electronics reseller please visit our Web site at www kramerelectronics com or contact a Kramer Electronics office from the list at the end of this document Your rights under this limited warranty are not diminished if you do not complete and return the product registration form or complete and submit the online product registration form Kramer Electronics thanks you for purchasing a Kramer Electronics product We hope it will give you years of satisfaction This page is intentionally left blank For the latest information on our products and a list of Kramer distributors visit our Web site where updates to this user manual may be found We welcome your guestions comments and feedback Web site www kramerelectronics com KRAMER E mail info Okramerel com SAFETY WARNING Disconnect the unit from the power e supply before opening and servicing P N 2900 300209 Rev 3
15. apters into the mains electricity Contents 1 Introduction 2 Getting Started 2 1 Achieving the Best Performance 2 2 Safety Instructions 2 3 Recycling Kramer Products 2 4 Shielded Twisted Pair Unshielded Twisted Pair 3 Overview 4 Defining the VA 1USB T and VA 1USB R USB Transmitter and Receiver 4 1 Defining the VA 1USB T USB Transmitter 4 2 Defining the VA 1USB R USB Receiver 5 Connecting the VA 1USB T and VA 1USB R 5 1 Connecting to the product via RS 232 5 2 Setting the Device ID DIP switch 5 3 Resetting the VA 1USB T to Factory Default Settings 5 4 Resetting the VA 1USB R to Factory Default Settings 6 Using the Web Pages 6 1 Accessing the VA 1USB T VA 1USB R Embedded Web Pages 6 2 The System Tab 6 3 The Network Tab 6 4 The Functions Tab 7 Wiring the Twisted Pair RJ 45 Connectors 8 Technical Specifications 9 Default Communication Parameters Figures Figure 1 VA 1USB T USB Transmitter Front Panel Figure 2 VA 1USB T USB Transmitter Rear Panel Figure 3 VA 1USB R USB Receiver Front Panel Figure 4 VA 1USB R USB Receiver Rear Panel Figure 5 Connecting the VA 1USB T Transmitter and VA 1USB R Receiver Figure 6 Machine ID DIP switch Figure 7 Entering the IP Address in your Browser Figure 8 Main Page System Tab Figure 9 System Tab Figure 10 Update Firmware Window Figure 11 Warning Message Figure 12 The Network Tab Figure 13 Warning Message Figure 14 The Functions Tab Figure 15 Warning Message
16. does not cover any damage deterioration or malfunction resulting from the installation or removal of this product from any installation any unauthorized tampering with this product any repairs attempted by anyone unauthorized by Kramer Electronics to make such repairs or any other cause which does not relate directly to a defect in materials and or workmanship of this product This limited warranty does not cover cartons eguipment enclosures cables or accessories used in conjunction with this product Without limiting any other exclusion herein Kramer Electronics does not warrant that the product covered hereby including without limitation the technology and or integrated circuit s included in the product will not become obsolete or that such items are or will remain compatible with any other product or technology with which the product may be used How Long Does this Coverage Last Seven years as of this printing please check our Web site for the most current and accurate warranty information Whois Covered Only the original purchaser of this product is covered under this limited warranty This limited warranty is not transferable to subseguent purchasers or owners ofthis product What Kramer Electronics will do Kramer Electronics will at its sole option provide one of the following three remedies to whatever extent it shall deem necessary to satisfy a proper claim under this limited warranty 1 Elect to repair or facilitate the
17. n the power to the device 3 When the Link LED starts to flash release the Link button The device is reset to factory default settings VA 1USB T VA 1USB R Connecting the VA 1USB T and VA 1USB R ji 11 6 Using the Web Pages The VA 1USB T and VA 1USB R provide built in Web pages accessible by standard Web browsers that allow you to configure and maintain the devices 6 1 Accessing the VA 1USB T VA 1USB R Embedded Web Pages Before you can use the embedded Web pages check that your computer is correctly connected to the VA 1USB T VA 1USB R via the Ethernet connection To access the VA 1USB T VA 1USB R embedded Web pages 1 Open your Internet browser 2 Type the IP address see Section 9 of the VA 1USB T VA 1USB R in the address bar of your browser The IP address for the VA 1USB T is shown for the IP address of the VA 1USB R see Section 8 E http 192 168 1 39 v Figure 7 Entering the IP Address in your Browser The screen shown in Figure 8 appears fersion Information KRAMER ELECTRONICS Ltd model VA 1U5B T kernel version 43 54 webfwh version V1 17 3 ware Figure 8 Main Page System Tab ET VA 1USB T VA 1USB R Using the Web Pages The Web pages consist of the following tabs e System tab see Section 6 2 e Network tab see Section 6 3 e Functions tab see Section 6 4 6 2 The System Tab Using the System tab Figure 9 you can e View the version information e Upda
18. ng the Web Pages Warning Reboot for new settings to take effect Figure 15 Warning Message 5 Rebootthe device by clicking on Utilities and clicking Reboot The device is rebooted with the new IP parameters VA 1USB T VA 1USB R Using the Web Pages Wiring the Twisted Pair RJ 45 Connectors When using STP cable connect solder the cable shield to the RJ 45 connector shield Figure 16 defines the TP pinout using a straight pin to pin cable with RJ 45 connectors EIA TIA 568B PIN Wire Color Orange White Orange Green White Blue Blue White Green Brown White Brown Figure 16 TP Pinout Wiring C N OD oo A ow N Pair1 4and5 Pair 2 1 and 2 Pair 3 3 and 6 VA 1USB T VA 1USB R Wiring the Twisted Pair RJ 45 Connectors 8 Technical Specifications VA 1USB T VA 1USB R INPUTS 1 USB host on a USB Type B 1 TP CAT 5 6 IN on an RJ 45 connector connector 1 Bidirectional RS 232 serial port 1 IR sensor on a 9 pin D sub connector F OUTPUTS 1 TP CAT 5 6 OUT on an RJ 45 4 USB devices on USB Type A connector connectors 1 Unidirectional IR port ona 1 Bidirectional RS 232 serial port on 3 5mm mini jack a 9 pin D sub connector F USB SUPPORT 1 1 and 2 0 bulk mode not isochronous ETHERNET SPEED 100 1000Mbps automatic selection RS 232 BAUD RATE Up to 115200bps MODE Full duplex POWER 5V DC 800mA 5V DC 2 8A CONSUMP
19. s for transmission back to the VA 1USB T More specifically the VA 1USB T and VA 1USB R support USB 2 0 high speed and USB 1 1 signals bulk mode not isochronous True Plug and Play operation without drivers All major operating systems Full duplex bidirectional RS 232 transmission Local and remote control of devices via the serial port Operation up to 100m 328ft apart Web pages for maintenance and configuration Automatic Ethernet speed selection Up to 16 independent pairs of devices on a single network 4 Defining the VA 1USB T and VA 1USB R USB Transmitter and Receiver This section defines the e VA 1USB T USB Transmitter see Section 4 1 e VA 1USB R USB Receiver see Section 4 2 4 1 Defining the VA 1USB T USB Transmitter In addition to encoding and transmitting the USB and RS 232 signals the VA 1USB T outputs the IR signal received from the VA 1USB R RS 232 commands and data flow bidirectionally allowing status requests and control of a destination unit Figure 1 defines the front panel of the VA 1USB T o l 9 IR OUT RS 232 USB Transmitter VA 1USB T Figure 1 VA 1USB T USB Transmitter Front Panel IR OUT 3 5mm Mini Jack Connect the IR blaster 1 2 RS 232 9 pin D sub Serial Connect to the serial controller Port Connector F Note The RS 232 link is bidirectional RESET Button Press to reset the device to factory default see Section 5 3 LINKLED Lights green when the TP link
20. te the firmware e Run functions fersion Information KRAMER ELECTRONICS Ltd model VA 1U5B T kernel version 43 54 webfwh version V1 17 Figure 9 System Tab To update the firmware 1 Click on Update Firmware The window shown in Figure 10 is displayed VA 1USB T VA 1USB R Using the Web Pages System Network Functions gt Version Information Update Firmware KRAMER ELECTRONICS Ltd Browse Warming Stop any service by disconnecting from the peer before you proceed to upgarde firmware gt Utilities Figure 10 Update Firmware Window 2 Click on Browse The Windows Browser is displayed 3 Browse to the new firmware file location 4 Select the new firmware file 5 Click OK The name of the new firmware file is displayed in the Update Firmware window 6 Click on Upload The update starts Warning Do not turn off or in any way interrupt the update process as this may cause the device to become inoperable 7 When the process is complete reboot the device as indicated by the message shown in Figure 11 by clicking on Utilities and clicking Reboot The device is rebooted with the new firmware VA 1USB T VA 1USB R Using the Web Pages Warning Reboot for new settings to take effect Figure 11 Warning Message 6 3 The Network Tab Using the Network tab Figure 12 you can modify the IP parameters of the device Currently only static IP addressing is allowed
Download Pdf Manuals
Related Search