PlatID600 - Humminbird
Contents
1. a a Er F an TRANSDUCER Y MAIN EOC WA Step 5 ANGLE ALLIGHMENT Set the transducer angle so that it is parallel with the bottom of the boat hull Once proper alignment is achieved tighten the two allen head screws using the 5 32 allen Figure amp wrench provided The screws are visible through the access holes on each side of the metal bracket Check to make sure the transducer main body is rigidly fastened to the pivot See Figure H Figure H aE So HOLE Fo nee E AMO TO Mial GG Abus HM Bie BCs SO THAT TT IS PARALLEL WARS Step 6 CHECK POSITION OF TRANSDUCER At this point check to see that the bottom of the transducer is a minimum of 1 below the bottom of the transom However as noted in STEP 2 the top of the transducer cannot fall below the bottom of the transom If it is not remove the transducer assembly from the metal bracket by removing the pin installed during STEP 3 Loosen the metal bracket mounting screws re position the bracket utilizing it s slotted holes tighten and re assemble It may be necessary to replace the silicone sealant after this adjustment is made NOTE It may be necessary to make several high speed runs to adjust transducer either UP DOWN or to re adjust the angle to achieve optimum results Step 7 CABLE CLAMPS Install cable clamps as necessary by drilling a 1 8 dia hole for the 8 screw Supplied 2 INSIDE HULL MOUNTING PROCEDURE Warning In o2. CETTE ie i pon be F a TRANSDUCER MOUNTING PROCEDURE Humminbird s high speed transducer is supplied with your LCR This transducer has been designed to give good high speed readings on most all boat designs including aluminum Please carefully consider the following before installing your transducer BOTT Oh FISH AY ZERO LIGHT AT SOFT AT MFT FISH A Al SOFT FLASHER DISPLAY LGA HSPrLAr WHAT ES JWOER HOY Pdi WHAT 5 Rn UNCER THE BOAT E AE PASSE CHER FISURE 1 TRANSDUCER MOUNTING OPTIONS A Transom Mount The Humminbird high speed transducer allows the transducer element to be mounted below the bottom of the boat hull keeping the transducer out of turbulent water and insuring good high speed operation The transducer will absorb the blow of any obstruction B by rotating up out of the metal spring bracket without harming the transducer or your boat The transducer can be re engaged by simply rotating the transducer down and snapping it back in place See Figure A Figura A Inside Hull Mount The high speed transducer can be mounted inside the hull without pivot assembly using the proper two part epoxy such as Humminbird s epoxy kit Even though there is some loss of signal in shooting through the hull your LCR will perform well with this type of installation You cannot shoot through the hull of an aluminum boat Trolling motor Mount This type of transducer is not supplied with your LC
3. Epoxy Kit or equivalent mix an ample amount of epoxy without causing it to bubble and pour it in the area the transducer is to be mounted The puddle should be larger than the bottom of the transducer 9 Coat the bottom of the transducer with epoxy then put it in the center of the puddle and push down on the transducer while moving it around in a circular motion This forces out any air bubbles that may be trapped between the bottom of the transducer and the hull of the boat 10 Let epoxy cure then the transducer is ready to operate No water is now required in the bottom of the boat and gas and oil that is spilled inside of the boat will not degrade performance as it will if the transducer is placed only in water CAUTION Do not use the silicone seal or any soft adhesive to bond the transducer to the hull This will reduce the sensitivity of the unit CAUTIONS 1 Occasionally the eye of your transducer may become dirty from storage or from contact with oils present in boats or marina environments Oil will cause the eye to lose the intimate contact with the water which is necessary for efficient operation The eye may be cleaned with liquid detergent 2 Improper installation of the transducer can alter the efficiency and accuracy of the entire system 3 If your boat of transducer is out of the water for a period of time it may take a short period of time for the transducer to become thoroughly wetted when returned t
4. far as it will go clockwise until you feel it lock Your connector is now locked into place Note For easy access to the connectors simply loosen the mounting knobs and tilt your LCR forward The connectors are now in full view and easy to plug or unplug TESTING THE INSTALLATION After installing your Platinum ID transducer and cables you should test the installation Testing should be performed on the water since that is the only way to check your transducer s performance With your boat at idle press the POWER button to turn the unit on The Platinum ID performs a self test on its electronics then automatically selects the right depth range and sensitivity level for conditions Momentarily you ll see the reading start to march across the screen from right to left Increase your boat speed to ensure that you get a continuous bottom reading as the boat moves Your Platinum ID and its transducer are designed to operate at up to 75 mph however use caution when operating any boat at high speed If the Platinum ID performs well at idle or slow speeds but the display is not continuous at higher speeds the transducer is not installed properly Air bubbles or turbulence from the boat hull are passing across the transducer face blocking the transmitting signal By following the instructions in Mounting the Transducer you can make simple adjustments that should fix the problem NOTE If other problems occur see Troubleshooting
5. later in this manual for tips from the Humminbird engineers If you don t find the solution there call our Customer Service Hotline USING THE PLATINUM ID This section provides complete information on operating the Platinum ID through its front panel controls You are encouraged to read this information completely as you first learn to use the Platinum ID doing so will ensure you make the most of its many features and functions The first part of this section explains the use of the built in simulator which you can use to practice selecting functions through the front panel The remaining instructions which can be followed while using the simulator or in actual operation explain each function and are organized according to the front panel layout USING THE BUILT IN SIMULATOR The Platinum ID includes a built in simulator that helps you learn to use your new equipment The simulator displays a typical underwater POWER scene and lets you practice with the controls The unit must be turned off before you start the simulator To activate it press down and hold the POWER button until a chirping sound begins Release the button and the built in simulator begins displaying a typical Platinum ID reading You can use the simulator to learn the functions explained in the following pages just as if you were getting actual on the water readings but note that Sensitivity is disabled To turn off the simulator turn off the unit by
6. pressing the POWER button again as y ths Of course the best way to learn the Pau ID is with actual use especially in familiar waters If you know what s below and see it on screen you ll quickly become and Platinum ID expert ON OFF PLATINUM ID FUNCTIONS The Platinum ID offers several functions that you can adjust with the front panel buttons Note that to select something with a button you must press it fully so that you can hear a chirp sound You can get acquainted with these features by actual operation or when using the simulator POWER Press the button once to turn the Platinum ID on then press again to turn the unit off When the unit is off keeping POWER pressed for about 2 seconds starts the built in simulator STOP Press this button to freeze the display so you can study it Press it again to restart the display movement SELECT This button is used to access the following functions for further adjustment ID Units Sensitivity Bottom Alarm Fish Alarm Zoom Range Bottom Lock Display Speed Depth Range Trip Log To adjust any of these press SELECT until the function you want appears Each function s display tells you how to use the arrow buttons and ONOFF for adjustment when first learning you should also refer to the following instructions The three position bottom hardness scale at the bottom of the screen helps differentiate between grass or muddy soft bottoms and struc
7. the same as for all Humminbird flasher units Use hardware provided to mount this base to the boat Next place the gimbal bracket on the swivel base and attach with four small machine screws provided Place the LCR in the gimbal mount and make certain the rubber washers provided are placed between the unit and the gimbal bracket Important Note which side of the gimbal faces forward Slots on gimbal bracket go towards rear Also rubber washer must be located between the unit and the gimbal bracket Install the mounting knobs and tighten snugly The unit can now be swiveled and tilted to any desired position Lo GIMBAL RER SCREW SWIVEL Lt 4 DECK MOUNT qa HUT LOCKWASHER FLAT WASHER FIGURE IMPORTANT RUBSER WASHER MUST BE LOCATED BETWEEN THE UNIT AND TRE GIMBAL BRACKET RUBBER WASHER MOUNTING KNOB a a __ i ae GIMBAL BRACKET IMPORTANT SLOTS ON GIMBAL BRACKET GO TOWARD REAR FIGURE 10 OTHER MOUNTING OPTIONS 1 The LCR gimbal bracket can also be mounted on the SM 4 quick disconnect swivel mount 2 The LCR gimbal bracket can also be mounted directly to the dash without the swivel mount however this method is not recommended since the unit cannot be rotated INSTALLING THE CABLES Your LCR comes equipped with Humminbird s new Angle Lock power and transducer connectors The power connector is identified with the letter P on the back of the plug It plugs into
8. R It is designed to mount on the foot of a trolling motor You may exchange your un used high speed transducer for a trolling motor transducer Call the Humminbird Customer Service Department Bronz Thru Hull Mount This transducer is not supplied with your LCR but for an additional cost you may exchange your un used high speed transducer for a bronz thru hull The bronz thru hull transducer has a threaded stem which installs through a hole drilled in the boat hull leaving the housing exposed under the boat This type of installation must be used for many boats with in board engines because there is no suitable location on the transom away from the noise and turbulence created by the prop A bronz thru hull transducer should be installed by qualified personnel only The LCR will operate well at high speeds with a properly mounted transducer Remember a transducer will not work transmitting through air or through air bubbles 1 TRANSOM MOUNTING PROCEDURE Step 1 MOUNTING LOCATION It is important that the transducer be mounted on the transom where water flow is in constant contact with the transducer You may wish to observe the rear of the boat while it is moving through the water to determine the best mounting location Step 2 BRACKET INSTALLATION Aluminum Boats To install the metal bracket on an aluminum boat locate the template on the transom between rows of rivets or ribs that are on the bottom of the boat Align the template so th
9. S This selection also affects Trip Log where recorded distance will be displayed in statute miles Bill or nautical miles NM 3 Selecting Sensitivity Factory setting 0 The Platinum ID automatically adjusts to the proper amount of sensitivity for conditions i e depth You can bias the setting or 5 levels to suit your personal taste Increasing the sensitivity adjustment can cause the display of very small targets and thermoclines which might not be displayed at the 0 setting If you want to manually adjust Sensitivity select SENS and press the UP or DOWN arrow button to adjust the display O I Adjusts sensitivity 4 Enabling Bottom Alarm Factory Setting OFF The Bottom Alarm lets you specify the minimum depth you want to maintain To use it select BOTTOM ALARM then press the ON OFF button to activate the alarm and the UP or DOWN arrow button to adjust the depth at which the alarm will sound A dashed line appears at the alarm depth when this function is on When Bottom Alarm is on you ll hear a continuous chirping sound when the bottom is shallower than you defined This is very handy for alerting you to shallow water or helping you to maintain position over structure a ldjusts alarm depth ON OFF Enables alar n 5 Enabling Fish Alarm Factory Setting OFF The Fish Alarm alerts you with a chirping sound whenever the Platinum ID detects fish or another object not attached to the botto
10. at the bottom corner of the template nearest the center of the transom is on the bottom edge of the transom Figure B TEMPLATE CENTER OF TRANSOM TRANSOM phe PARALLEL DEADRISE TO WATER ANGLE BOTTOM EDGE OF LOCATE TEMPLATE TO BOTTOM OF TRANSOM TRANSOM AND DRILL HOLES PER INSTRUCTIONS Once the location is determined mark and drill three 7 64 dia holes noted on the template Attach the metal bracket using three 10 self threading screws supplied Be sure to align holes in the center of the Bracket slots On some aluminum boats it may be necessary to use a wood back up plate It is important to use a silicone sealant between the screwhead and bracket in order to prevent leaking See Figure C METS BrAALEET 410 SRR on Figure i Step 2 BRACKET INSTALLATION Fiberglass Boats If your boat has a stepped transom located below and under the main transom the compact transducer design allows mounting in this area This mounting location is recommended for good reading at very high speeds See Figure D To install the metal bracket on a fiberglass boat locate the template on the transom in the same manner as for an aluminum boat See Figure C Figure D TAANSOM TEMPLATE nl EE MOUNT HERE FOA EXTRA HIGH SPEED OPERATION ON BOATS WITH STEPPED TAANSOM ERAT SIDE NOTE On boats with more than 15 degree deadrise angle it may be necessary to mount the transducer slightly off parallel with th
11. e water level See Figure E Mark and drill the three 9 64 dia holes as shown on the template Attach the metal bracket using the three 10 self threading screws supplied Be sure to align the holes so that they are centered vertically in the three slots found in the bracket It is important to use a silicone sealant between the screwhead and bracket in order to prevent leaking Figure TEMPLATE DEADRISE 15 MORE Ze THAN 15 Step 3 TRANSDUCER PIVOT ASSEMBLY Assemble the pivot to the transducer main body using the two 4 x5 8 allen head screws two 3 8 tooth washers and two 14 square nuts Make sure the tooth washers are sandwiched between the transducer main body and the pivot The square nuts are trapped inside the pivot and will not rotate as the allen head screws are tightened HOWEVER DO NOT TIGHTEN AT THIS POINT See Figure F CAUTION DO NOT APPLY LOCTITE OR SIMILAR LOCK THEY WILL ATTACK THE PLASTIC inane Figure F Step 4 TRANSDUCER ASSEMBLY Insert the transducer assembly into the metal bracket from the bottom Push up until the holes in the plastic pivot align with the uppermost holes in the bracket Slide the O ring on to the headed pin and insert it through the two parts Assemble by screwing the 4 x3 8 allen head screw into the end of the pin and tighten See Figure G CABLE CLAMP PE BCREW PLH ung 8 Fl a kr d IFN a0 METAL SPARING BAACKEL ores Ko 5
12. m To activate it select FISH ALARM and press the ON OFF button Initially the fish alarm will sound when any target not attached to the bottom is detected The word ALL is displayed on the menu and two fish are shown on the lower part of the display By pressing either arrow button the word LARGE appears on the display and the alarm will only sound when a large target is detected A single fish symbol is shown on the bottom of the display to represent that large fish only is selected While there is some variation in sonar characteristics of different species typically the strength of the return is relative to the size of CE T 7 Selects all or large the fish Or Enables alarin 6 Using Zoom Range Factory Setting OFF Zoom Range provides an up close view To activate it select ZOOM RANGE and press ONOFF The Zoom view begins initially at the surface press the UP or DOWN arrow to adjust Zoom depth The range of the display is shown when Zoom is on The Zoom range depends on the current Depth Range 7 2 in the 15 and 30 Depth Ranges 15 feet in the 60 120 and 180 Depth Ranges and 30 in the 240 360 480 and 600 Depth Ranges You can adjust zoom depth before activating zoom in which case the zoom range will be shown with horizontal dotted lines Velects zoom di ph Sn Hr Enables zoom 7 Using Bottom Lock Factory setting OFF Bottom Lock provides an up close view like Zoom Ra
13. nge except that in this case the zoomed view automatically moves up or down to stay on the bottom To use this feature select BOTTOM LOCK and press ON OFF The range of the display is shown when Bottom Lock is on This is an ideal feature for finding structure or locating fish near the bottom Remember If Bottom Lock is the last function you selected you can use the ON OFF button to switch Bottom Lock on and off without having to press SELECT first ON OFF Enables bottom lock 8 Setting Display Speed Factory Setting One level below maximum The Platinum ID display is updated advances across the screen as you move through the water The speed at which the display is updated depends on the Display Speed setting To adjust it select DISPLAY SPEED and press the UP arrow button for a faster setting or the DOWN arrow for a slower setting In general higher Display Speed settings provide faster updates while slower Display Speeds provide more detailed information HT 5 Adjusts speed 11 Trip Log TRIP MG Factory Setting Off HUERAGE SPEED The Platinum ID Trip Log provides a full screen of hHIFH information on current conditions To display it select TRIP FLAFPSEDR DIGTAHCE LOG and press ON OFF eds All log information is continuously updated as long as the Platinum ID remains powered on If you want to ELAPSED TIME reset Average Speed Elapsed Speed and Elapsed Q 0 3 3 Distance press the STOP but
14. o the water Also re entry may cause turbulence which will create air bubbles in the eye of the transducer The bubbles will disappear in a short time or can be removed by rubbing the transducer eye with your fingers while the transducer is in the water 4 If your instrument should fail to function be sure to check all the electrical connections before removing the transducer or calling a serviceman 5 Inspect your transducer cable and make sure that it has not been cut or damaged to the point where it will affect the performance of the transducer A slight nick or cut exposing the outer cable can be repaired by wrapping with electrical tape A transducer can be damaged if the inner cable and outer cable are allowed to make contact Such a problem can sometimes be corrected by properly splicing the coaxial cable This should only be attempted by a qualified service technician 6 If your LCR is not working properly and you suspect the problem might be in your transducer we would recommend you borrow a unit from a friend and try it on your boat If the symptoms are the same you can almost be certain that the problem is in the transducer INSTALLING THE LCR The LCR should be mounted on a flat solid surface for maximum stability The low profile swivel mount has four holes drilled in the base It is recommended that all four holes be used Position the swivel base and drill four 14 diameter holes Note The LCR hole pattern Is
15. rder to achieve proper results with this type installation it is important that the transducer be mounted by someone familiar with the use of two part epoxy adhesives For this reason Techsonic Industries Inc will not be responsible for any damage due to the mounting of your transducer in this manner NOTE An Epoxy Kit Part N EPK is available from Humminbird This Epoxy Kit has been formulated for Inside Hull Transducer Installation 1 Select as flat an area as possible near the aft end and center of boat where the hull is thin and not double If the bottom has a runner down the center of boat select an area to one side of the runner but as close to the runner as possible 2 Clean the inside of the boat with lacquer thinner in the area transducer is to be mounted Outside of boat in this area should also be cleaned Not with lacquer thinner 3 Put approximately one inch of water in the bottom of the boat 4 Put transducer in the water The bottom of the transducer should be in a flat area and should be in good contact with the bottom of the boat 5 Operate the LCR with the boat operating at high speed The transducer may have to be moved in order to find an area where satisfactory operation is observed 6 When an area is found that produces satisfactory operation mark the location of the transducer 7 Remove the water and transducer and clean the marked area and the bottom of the transducer thoroughly 8 Using the Humminbird
16. the outlet on the back of the unit marked Power The transducer connector is identified with the letter T and plugs into the outlet on the back of the unit marked Transducer Note An adapter AD 4 is available to allow use of an old waterproof BNC transducer with the LCR but be sure that the transducer is a 16degree A 32 degree transducer cannot be used A 11 8 hole must be drilled to pull through the transducer connector After drilling the hole pull the transducer connector up through the hole If you are installing two units both transducer connectors can be pulled through this 1 1 8 inch hole Next push the power cable wires down through the hole A hole cover has been provided which will dress and hold the wires Install the hole cover after determining the necessary wire length from the hole The power cable has a red lead to the positive post and the black lead to the negative post Install a 1 amp fuse between the red cable and positive post of your 12 volt battery If a fuse panel is available we recommend wiring the power cable into the fuse panel Note The LCR must be fused separately from any other accessory Your Angle Lock connectors can only be plugged in one way Position the connector so the letter P or T can be read and the 90 degree bend is pointed downward Push the connector in as far as it will go Turn the positive locking ring as far as it will go clockwise until you feel it lock Locking ring as
17. ton STOP CLROFF EXIT Pressing On OFF exits the Trip Log and returns SENS I ee m you to normal Platinum ID operation ics 7 39 wt NOTE Trip Log requires proper input from the speed accessory on the transom of the boat AEO Resets timer SH Errables timer
18. ture or rock hard bottoms After you adjust any function the display returns to its full screen reading If the menu doesn t stay on the screen long enough press the STOP button to hold the menu on the screen NOTE The last function you select remains active that is you can adjust it without having to press SELECT again For example if the bottom alarm was the last function used you can readjust the alarm by pressing one of the arrow buttons Or if you often use Zoom you can select it once then switch it on and off simply by pressing ON OFF What You See on the Display era een Line Fish warns De ond eg Depth Rotam Range Canmlour is Mariom 4 low Hardness Indicator Scale D SENS 2 a 7 Sensiiivily 155 777 i Seming Depth Hiner Haat femperafure Speed 1 Selecting ID Factory Setting Fish symbols LAO Selecis ID symbol CaF Enables ID ID identifies targets not attached to the bottom and displays them with either a fish symbol or an arch Three different size symbols are used to represent the returned signal strength a good indicator of fish size Use the up and down arrow keys to switch between fish or arches or use the ON OFF key to disable ID 2 Selecting Units Factory Setting MPH SM CE Selects ID symbol HoF Enahles ID If you are using the trolling speed accessory with your Platinum ID you can switch the units of measurement between miles per hour MPH or knots ART
Download Pdf Manuals
Related Search