Accessory Mounting Brackets and Covers for 6180 Industrial
Contents
1. Red Wire 7 ae 5 Install the back panel 6 Apply power to the 6180 Computer and verify operation of the drive You may need to edit BIOS settings to recognize the drive or to allow the operating system to detect the new hardware 12 Accessory Mounting Brackets and Covers 2 5 Inch Solid State Drive Mounting Brackets The solid state drive mounting brackets allow you to mount a 2 5 inch or solid state drive in one of the drive bays of the 6180 computer chassis Mounting Bracket for 2 5 Inch or Solid State Drives Catalog No 6189 IBSDBRKT for Series A and B Installation To install a drive using the solid state drive mounting bracket 1 Secure the drive to the bracket with the four mounting screws Tighten screw to a torque of 6 8 in lbs 7 9 Nem Bracket Part No 6189 IBSDBRKT Mounting Screws 4 Important If you are installing a 2 5 inch drive you must remove the four standoffs and mount the drive directly to the bracket Use the mounting screws provided with the drive 2 Position the drive bracket assembly into the chassis Make sure the hook on the bracket slides into the corresponding hole in the chassis Also make sure that the key on the end of the bracket is inserted into the slot on the chassis front panel 3 Secure the drive bracket assembly to the chassis with the two mounting screws Tighten screw to a torque of 6 8 in lbs2. To install the rear cover plate 1 Remove the back panel to the 6180 computer 2 Position the cover on the inside of the back panel 3 Secure the cover with the screw provided Tighten screw to a torque of 6 8 in lbs 7 9 Nem 4 Install the back panel on the 6180 computer Accessory Mounting Brackets and Covers To install a front cover ATTENTION If the 6180 Computer is installed with mounting clips the mounting clips on the hinge side will interfere with the opening of the hinge Remove the mounting clips on the hinge side before swinging chassis away from the bezel Failure to remove clips may damage clips and the chassis ATTENTION Remove all cables from the the side panel connectors Failure to remove cables may cause damage to the cables and connectors p Swing open the back of the computer chassis after removing the three bezel latching screws Refer to 6180 computer user manual for instructions if required Front Bezel Latching Screws 3 aS ee Chassis Swings Away From Bezel Accessory Mounting Brackets and Covers 9 2 Position the front cover inside the front bezel assembly and secure with the screw provided Tighten screw to a torque of 6 8 in lbs 7 9 Nem Install Screw to Secure Cover Install Front Cover from the Inside a T lt S Make sure bottom edge of cover fits between edge of chas
3. 6180 Computer is installed with mounting clips the mounting clips on the hinge side will interfere with the opening of the hinge Remove the mounting clips on the hinge side before swinging chassis away from the bezel Failure to remove clips may damage clips and the chassis 2 Swing open the back of the computer chassis after removing the three bezel latching screws Refer to 6180 computer user manual for instructions if required Front Bezel Latching Screws 3 r RL Chassis Swings Away Cover Knockout From Bezel for Rear Mounting of Drive 3 Position the accessory drive bracket assembly into the chassis Notes For rear facing drives you may have to remove the panel knockout shown above if a rear mounted drive was not previously installed Insert screwdriver into slot on knockouts and pry back and forth on knockout to remove Use a pliers to remove the center rib between the two knockouts For front facing drives if a floppy drive was not previously installed you may have to replace the floppy drive cover behind the front access door with a cover having an opening Refer to Floppy Drive Front Cover on page 7 for a description of the available covers Accessory Mounting Brackets and Covers 4 Connect the cable connectors to the floppy drive Connectors are keyed so they cannot be installed backwards Align the floppy drive bra
4. 7 9 Nem Accessory Mounting Brackets and Covers 13 4 Install the IDE converter board provided with bracket on the two standoffs on the left side of the drive bays The converter board snaps on to the standoffs no hardware is required IDE Converter Board 5 Connect the shorter processor board IDE cable provided with bracket and power connector to the IDE converter board Drive Cable provided with bracket Connects Here S IDE Converter Board Power Supply Cable for Drive Connects Here IDE Cable From Processor Board Connects Here 14 Accessory Mounting Brackets and Covers 6 Connect the drive ribbon cable provided with bracket to the IDE converter board and the drive The red wire of the cable must be at the bottom as shown below IDE Converter Board o Red Wire a 7 Install the back panel 8 Apply power to the 6180 Computer and verify operation of the drive You may need to edit BIOS settings to recognize the drive or to allow the operating system to detect the new hardware CD ROM Covers Catalog No 6189 F CDBRKT Catalog No 6189 F CDBRKTB Catalog No 6189 RCDBRKT Catalog No 6189 RCDBRKTB Accessory Mounting Brackets and Covers 15 The CD ROM covers provide protection for the part of the drive that extends from the 6180 compute
5. design manufacture and support a broad Allen Bradley range of automation products worldwide They include logic processors power and motion control devices operator interfaces sensors and a variety of software R ockwell is one of the world s leading technology companies E N Worldwide representation eres nt Argentina s Australia e Austria e Bahrain e Belgium e Brazil e Bulgaria eC anada e Chile s C hina PRC e Colombia e Costa Rica s Croatia e Cyprus e Czech Republic e Denmark e Ecuador e Egypte ElSalvador e Finland eF rance e Germany e Greece s Guatemala e Honduras e HongKong s Hungary e Iceland e India e Indonesia s Ireland e Israel e Italy e Jamaica s apan eJ ordan e Korea e Kuwait Lebanon s Malaysia e Mexico e Netherlands e New Zealand e Norway e Pakistan s Peru e Philippines eP oland e Portugal e P uerto Rico e Qatar e Romania e R ussia CIS e Saudi Arabia e Singapore Slovakia eS lovenia e South Africa Republic e S pain e Sweden e Switzerland e Taiwan e Thailand e Turkey e United Arab Emirates s United Kingdom s United States e Uruguay s Venezuela lt Yugoslavia Allen Bradley Headquarters 1201 South Second Street Milwaukee WI 53204 USA Tel 1 414 382 2000 Fax 1 414 382 4444 41061 042 01 D Copyright 1998 Allen Bradley Company Inc Printed in USA
6. Covers and Brackets Instructions Accessory Mounting Brackets and Covers For 6180 Industrial Computers This instruction sheets provides installation instructions for the following accessory brackets and covers Part Number Catalog Number Description Page Floppy Drive Lower Bay Mounting Bracket 6189 LBF DBRKT Includes 4 drive mounting screws and 4 bracket 2 mounting screws Includes Drive Cable LEP x 6189 UBF DBRKT Floppy Drive Upper Bay Mounting Bracket B A Includes 4 drive mounting screws and 1 bracket 5 6189 UBFDBRKTB S i ee LO mounting screw Drive cable is included 6189 FDDCVR Floppy Disk Drive Cover Plates Contains four covers 7 6189 FDDCVRB and 3 cover mounting screws 3 5 Inch Hard Drive Mounting Bracket 6189 IB35BRKT Includes 4 drive mounting screws and 2 bracket 10 mounting screws Solid State Drive or 2 5 Inch Hard Drive Mounting Bracket Includes 4 drive mounting screws 2 bracket E i STRTESDERKT mounting screws adapter board 2 5 inch hard drive cable and IDE cable Cover kit protects CD ROM drive when drive is installed 6189 F CDBRKT over kit protec rive when drive is installe facing the front of the 6180 computer Includes 2 cover 15 6189 F CDBRKTB mounting screws and 4 drive mounting screws Cover kit protects CD ROM drive when drive is installed Ghanaians facing the rear of the 6180 computer Includes 3 cover 15 6189 RCDBRKTB mounting screws and 4 d
7. cket or CDROM and chassis mounting holes and secure the with the 4 mounting screws provided with the bracket or CDROM Tighten screws to a torque of 6 8 in lbs 7 9 Nem For Floppy Drive Bracket Assembly j O see 5 8 E O Front x Use these chassis holes for both rear and front mounting of a floppy drive For front 0 access mounting use the rear hole pairs on the mounting bracket For rear access mounting use the front hole pairs on the O U mounting bracket 6180 Computer Bottom View ae For CDROM Drive aal 0 0 For front access mounting of a CDROM O O O drive use chassis hole pairs 2 and 5 and or 2 the front hole pairs on the CDROM OJ 1 3 For rear access mounting of a CDROM drive use chassis holes 3 and the rear hole pair on the CDROM o 0 O Front 6180 Computer Bottom View 6 Swing the chassis back onto the bezel and secure chassis with the three latching screws Tighten screws to a torque of 18 22 inch Ibs 2 2 5 Nem Install the back panel Apply power to the 6180 Computer and verify operation of the drive You may need to edit BIOS settings to recognize the drive or to allow the operating system to detect the new hardware Accessory Mounting Brackets and Covers 5 Floppy Drive Upper Bay The upper bay mounting bracket allows you to mount a floppy drive Mounting Bracket out the side o
8. f the 6180 computer chassis e Mounting Bracket for Upper Bay Floppy Drive Catalog No 6189 UBFDBRKT for Series A Catalog No 6189 UBFDBRKTB for Series B Upper Bay Mounting of Floppy Drive Upper Bay Mounting of Floppy Drive Back Panel Installation To install a floppy using the upper bay mounting bracket 1 Secure the floppy drive to the drive bracket using four screws supplied with the drive Tighten screws to a torque of 6 8 in Ibs 7 9 Nem Floppy Drive Upper Bay Drive Bracket 6189 UBFDBRKT Accessory Mounting Brackets and Covers 2 Remove the back panel to the 6180 computer 3 A shorter drive cable is provided with the mounting kit for mounting in the upper bay Connect the cable to the floppy drive connector on the processor board refer to the Processor Board user manual if necessary and the connector on the back of the drive 4 Position the accessory drive bracket assembly into the chassis The edge of the bracket fits under the tab at the front of the chassis Note You may have to remove the side panel knockout shown below if a side mounted drive was not previously installed Insert screwdriver into slot on knockouts and pry back and forth on knockout to remove Use a pliers to remove the center rib between the two knockouts ATTENTION If knockout is removed carefully remove any burrs or sharp edges Failure to rem
9. ove sharp edges could result in personal injury 5 Align the bracket and chassis mounting hole and secure the drive bracket assembly with a mounting screw Tighten screw to a torque of 6 8 in lbs 7 9 Nem Cover Knockout for Upper Bay Mounting of Drive NS Bracket with Drive in Upper Bay Bracket Mounting Screw 6 Install the back panel 7 Apply power to the 6180 Computer and verify operation of the drive You may need to edit BIOS settings to recognize the drive or to allow the operating system to detect the new hardware Floppy Drive Cover Plates Accessory Mounting Brackets and Covers 7 The floppy drive cover plates provide protection for installed floppy drives e Floppy Drive Cover Plates Catalog No 6189 FDDCVR for Series A Catalog No 6189 FDDCVRB for Series B There are four floppy drive cover plates 2 front covers 2 rear covers Use the cover plates as follows Use this rear cover when a floppy drive is rear mounted Use this rear cover when front mounting a floppy drive or if a floppy drive is not installed Use this front cover when Floppy Drive is front mounted The cover mounts under the front access door to protect the front of the floppy drive Use this front cover when Floppy Drive is rear mounted or not installed The cover mounts under the front access door to protect the rear of the floppy drive or to prevent access to the inside of the computer
10. r chassis Two cover kits are available Cover Kit for Front Mounting of CD ROM Catalog No 6189 FCDBRKT for Series A Catalog No 6189 FCDBRKTB for Series B Cover Kit for Rear Mounting of CD ROM Catalog No 6189 RCDBRKT for Series A Catalog No 6189 RCDBRKTB for Series B Installation Note There are two bags of screws provided with the bracket Use the three flush head mounting screws to mount the covers Use the remaining four screws to secure the CD ROM drive Use this rear cover when a CD Drive is front mounted The cover mounts on the back panel to protect the rear of the CD drive Use this front cover when a CD Drive is rear mounted The cover mounts under the front access door to protect the rear of the CD drive Use this rear cover when a CD Drive is rear mounted The cover mounts to the back panel to protect the front of the CD drive while allowing access to the drive To install a rear cover 4 Remove the back panel to the 6180 computer Position the cover on the inside of the back panel Secure the cover with the screw provided Tighten screw to a torque of 6 8 in lbs 7 9 Nem Install the back panel To install a front cover refer to the instructions on page 8 To install a CD ROM refer to the instructions on page 4 ZR Rockwell Automation Allen Bradley a Rockwell Automation Business has been helping its customers improve productivity and quality for more than 90 years We
11. rive mounting screws The catalog numbers identify Series B parts by adding B to the end of the catalog number Make sure the series letter of your computer is appropriate for the brackets When a catalog number for a bracket does not have a letter B atthe end that bracket applies to Series A and Series B units Floppy Drive Lower Bay Mounting Bracket Front Mounting Drive Bracket Accessory Mounting Brackets and Covers The lower bay mounting bracket Catalog No 6189 LBFDBRKT allows you to mount a floppy drive facing either the front or the back of the 6180 computer as shown below e Mounting Bracket for Lower Bay Floppy Drive Catalog No 6189 LBFDBRKT for Series A and B Rear Mounting Installation Note You can also use these procedures to intstall a front or rear facing CDROM drive without mounting bracket The lower bay floppy drive mounting bracket and CDROM drive use the same sets of chassis mounting holes To install a floppy using the lower bay mounting bracket 1 Secure the floppy drive to the drive bracket using four screws supplied with the bracket Tighten screws to a torque of 6 8 in Ibs 7 9 Nem Drive Mounting Screws 4 E d oppy Drive Accessory Mounting Brackets and Covers 3 ATTENTION Remove all cables from the side panel connectors Failure to remove cables may cause damage to the cables and connectors ATTENTION If the
12. sis and the two tabs NN S gt Edge of Chassis 3 Swing the chassis back onto the bezel and secure chassis with the three latching screws Tighten screws to a torque of 18 22 inch Ibs 2 2 5 Nem 10 Accessory Mounting Brackets and Covers 3 5 Inch Hard Drive The hard drive mounting brackets allow you to mount a 3 5 inch Mounting Bracket drive in one of the drive bays of the 6180 computer chassis e Mounting Bracket for 3 5 Inch Drives Catalog No 6189 IB35BRKT for Series A and B Installation To install a drive using the hard drive mounting bracket 1 Secure the drive to the bracket with the four mounting screws Tighten screw to a torque of 6 8 in lbs 7 9 Nem 3 5 Inch Drive Bracket Part No 6189 IB35BRKT Mounting Screws 4 2 Position the drive bracket assembly into the chassis Make sure the hook on the bracket slide into the corresponding hole in the chassis Also make sure that the key on the end of the bracket is inserted into the slot on the chassis front panel 3 Secure the drive bracket assembly to the chassis with the two mounting screws Tighten screw to a torque of 6 8 in lbs 7 9 Nem Accessory Mounting Brackets and Covers 11 4 Install the ribbon connector on the hard drive On 3 5 inch drives also connect the power cable Make sure that the ribbon cable is installed correctly The red wire of the cable must be at the bottom as shown below Drive E
Download Pdf Manuals
Related Search