Home

RST620 Quick Start Guide

image

Contents

1. avoid routing cables above the catalytic converter 3 Installing your Transceiver Module 4 Installing your Directional Microphone o Installing your Speaker 6 Installing your Antenna refer to separate guide 7 Connecting Power Testing amp Operation 1 x Microphone 1 x L Band transceiver 9922B5 1 x L Band transceiver bracket amp Velcro fastener 1 x L Band transceiver cable 1 x 3 wire Power cable harness amp 2 Fuses 1 x Allen key 1 x Printed RST620 User Manual information contact the vehicle manufacturer gt Use grommets wherever a cable must pass through a hole in a metal panel gt In a vehicle equipped with electronically controlled anti skid brakes ABS route all cables on the opposite side of the vehicle from the braking modulator box to minimize any possible interference gt Keep all in line connectors accessible Installing your handset amp holder hang up cup Mount the hang up up of the Intelligent Handset so that the handset is within easy reach of the driver during normal operation and will not interfere with driver or passenger comfort Orient the handset hang up cup vertically with the spring loaded clip toward the front of the vehicle When selecting an installation location please consider ha aa g gt Each mounting surface is strong enough to support Pic 1 Pic 2 Pic 3 the handset gt Ensure that handset is within reach of the RST620
2. interface unit HFI Allow enough room to gt your handset needs to connect to the Hands Free Interface HFI gt easily insert the handset into and remove it from the hang up cup Step 1 Remove cover on hang up cup Pic 1 Step 2 Affix the Hang up cup in location using the holes in the cup Pic 2 Step 3 Once in place replace cover on hang up cup Installing your Interface box HFI The best location for mounting the HFI is under the dashboard or front seat within reaching distance of your handset above when in the cradle To install the box follow these steps 1 Using the HFI as a template mark the screw hole locations 2 Remove the bracket and drill holes at the marked locations 3 Mount using the six screws provided with the fuse kit RST620 Options amp Accessories 710 Iridium Helix Antenna Miore info www beamcommunications com 714 Whip Antenna Installing your Transceiver Module Mount the Transceiver module in a safe location away from driver obstruction Ensure the distance between the transceiver module and the Hands Free Interface enables the D25 Connector cable to reach both units Use the pre assembled bracket 3x 4mm slots and Velcro tape Supplied to conveniently attach the Transceiver module to a fixed surface Optimising Iridium performance Iridium is a line of sight Satellite network conditions that can compromise the quality of the service you may r
3. required at all 2 Route the power cable from the HFI to the connection point times even when the vehicles turned off then the power should be connected to constant 11 32V DC input 5 Be aware of the possibilities of this however flattening the vehicle battery Note To limit ground loops and high impedance ground paths run the green red stripe and black wires directly to the battery or as close to the battery as possible Use a grommet or other protection to prevent Hands free Interface LEDs wear on metal surfaces for these wires The Interface unit has a green status indicator LED which indicates 3 Prepare the fuse block Remove all fuses and tape them to their respective holders before making any Ir j yn connection DO NOT insert fuses until you have completed and inspected all connections Flash si 4 Connect the BLACK Ground wire to negative battery vehicle chassis if negatively grounded chassis ace p l J y 5 Connect the RED Battery wire to the vehicle Battery eg 12V via a GA fuse Steady on 6 Connect the GREEN Accessory wire to the vehicle accessory power via a 1A fuse This may be connected to Flash fast Vehicle Ignition voltage if Accessory power is unavailable
4. Beam Communications Pty Ltd Anzed Court Mulgrave Victoria Australia 3170 T 613 8588 4500 F 61 3 9560 9055 E info beamcommunications com W www beamcommunications com Quick Start Guide Pri I S Fixed Handsfree Car Kit BEAM Brees Package Contents Before commencing installation ensure your package has the following components 1 x RST620 Hands Free Interface HFI module 1 x Intelligent Handset amp cradle 1 x Speaker Thank you for purchasing your BEAM Fixed In Vehicle Handsfree kit This QuickStart Guide lists the installation steps LOOSOOSSHUYSN 1 Installing your handset amp holder 2 Installing your Hands Free Interface Unit HFI Installation guidelines gt Always protect equipment from dirt and moisture gt Ensure mounting surfaces are strong gt Allow for cooling space amp driver passenger leg room gt Ensure all wires are secure gt Always use the supplied mounting hardware gt Ensure removal is easy as above Note Only qualified people should install communication equipment For vehicle air bag Routing Cables Use wiring troughs when available to simplify cable installation and to provide maximum protection for cables If wiring troughs are not available route cables under the carpet alongside the drive shaft hump and follow these guidelines gt Route cables so they are protected from pinching sharp edges and crushing gt Where possible
5. e 3 Ensure that the Intelligent Handset is plugged into the HFI gt Do not position the microphone where it may be blocked by the visor gt Position the microphone so that it faces the user of the mobile when the user is seated normally the pl gt Do NOT position the microphone near a window or in any location where road noise or any A p a 4 Turn on the ignition to ACC or ON position ambient background noise may be high above 85 dB SPL NLY p 5 The handset should now be on after few seconds attempting to find Satellite network gt Do NOT position the microphone where it will be affected by the output of the speaker see 6 Wait for the unit to register on the network 20 to 40 seconds below 7 You are now ready to make and receive calls Checking performance after installation Installing the Speaker LALLE to confirm your car kit is working properly 1 Make a call from the handset in the cradle and confirm operation 2 Make a call to the handset and confirm operation 1 Mount the speaker to the transmission hump or underneath a is ise dashboard on passenger side Zp 2 Mount speaker so it faces AWAY from microphone this can fo cause feedback through the system 3 To avoid damaging the cable route the cable carefully to ensure that it does not get crimped by any heavy objects or enclosures Important Operational Notes 1 When the vehicle ignition is turned off the handset will be turned off aft
6. eceive include 1 Obstructions Provide the best satellite view for your antenna by removing all obstructions where possible 2 Cabling Use the shortest cable length and the fewest number of connectors on all Iridium certified antenna cable runs 3 RF Interference Install antenna as far away from other transmitters as possible L Band Transceiver Setting up your BEAM RST62O0 Fixed Handsfree Car Kit HFI Side 1 HFI Side Acc Ignition 1A Fuse O PSN Tey CAUTION RED BATT 11 to 32 VDC gt s DO NOT connect power BLACK BATT GND es to the battery until the eRe a ain installation is complete Power Line In Out LED Optional Ground x Negative 7 Positive esas DBS Comm Microphone Joining Cable s 3A Fuse pari Port maT Intelligent Handset ri Optional NIA Installing the Directional Microphone She AS The hands free directional microphone must be properly positioned in the vehicle to ensure y pnan gt optimum performance U CA E a j When selecting a location for the microphone consider these guidelines Vy a T ina amp O gt Mount the microphone near the centre of the vehicle either on the driver side sun visor or esting peration on the head liner above the driver 2 Once steps 1 7 have been completed test the installation by following this checklist 1 Ensure the Satellite terminal has power to the unit 2 Ensure that the vehicle is located in an area where quality signal is availabl
7. er a delay as follows The unit will prepare to turn off phone after the first 5 seconds The vehicle ignition can be returned to ACC ON position during this time and the phone will remain on without phone power dropout This is useful if the vehicle was inadvertently turned off during a voice call If ACC remains off then the Interface unit will also turn off after a further few seconds l ns 2 If during operation of the Hands free unit the unit either does not turn on or will not turn off it is recommended to Installing your External Iridium Antenna follow these steps see the specific Iridium Antenna Installation Guide manual or visit us www beamcommunications com gt Turn vehicle Accessories off gt Turn the terminal off gt Wait 10 seconds gt Turn on the vehicle Accessories once more 3 If the power button is pressed after the accessories has already been turned off in the vehicle the telephone will Connecting Power operate for a period of 20 minutes before the unit will power off If after 19minutes a call is in progress the terminal will 1 Ensure the power and Interface cable to the HFI will reach from the RST620 unit to the point at which vehicle stay on for another 20 minutes This feature is to minimise drain on the battery power is being sourced DO NOT connect to the HFI until after the installation is complete 4 The power to the terminal is dependent on the poser source chosen during installation If power is

Download Pdf Manuals

image

Related Search

Related Contents

AIC B03/12 - Service d`état de l`Aviation civile  MASTERTOP BC 375  ARCHITEXTO APPEL A CANDIDATURES auteurs/écrivains  Klipsch RF-82 II  RUFNEK 80  Logitech 939-000934  Tenda W368R  Zanussi ZH63E Operating Instructions  Ventilador de torre STV 45 A1 Ventilatore a colonna  ラインナップ 設定マニュアルについて  

Copyright © All rights reserved.
DMCA: DMCA_mwitty#outlook.com.