M4x Start Up Guide 3 - Raven Electronics Corporation
Contents
1. AEGEA PARRE EER S a Sut weet ae i H Pr a k san eUir etd EAE a he tions ots M4x Blade Quick Start Guide Raven Electronics Corporati on 1968 so Please Read Before You Start Thank you for purchasing the M4x Blade When unpacking your M4x Blade confirm the following items were received with your shipment Software CD This CD also includes the User Manual e AC Power Supply Adapter 120 240 VAC 12 VDC 2 5 Amp regulated Note on units powered from a DC source this item will not be included Power Cord Note on units powered from a DC source this item will not be included USB Cable If any of these items are missing please contact Sales at 175 858 2400 press 2 Installing The M4x Software Note Install this software before plugging in the M4x Blade Uninstall old M4x Software before installing a new version 2 Install the software by inserting the CD into the computer s CD Drive We recommend selecting Easy Install when prompted Follow the on screen prompts to complete the installation Refer to the M4x User Manual included on the software disk for more detailed installation instructions especially if this version of software will be installed over a prior version of software Powering Up the M4x Blade 1 Connect the Power Cable into the AC Power Adapter 2 Connect the AC Power Adapter to your AC power source e g 3 pronged grounded wall outlet The AC Po2. PIN 4 PIN 4 PIN4 RLY2NC PIN4 RLY 4 NC PIN 4 NC PIN 4 NC PIN 5 Jem PIN 5 Jem PIN 5 RLY 2 COM PINS RLY 4 COM PIN 5 NC PIN 5 NC PIN 6 NC PIN 6 NC PIN 6 RLY2NO PING RLY 4 NO PIN 7 PIN 7 PIN 7 NC PIN 7 NC PIN 7 NC PIN 7 NC PIN 8 fete PIN 8 Jew PIN 8 NC PIN 8 NC PIN 8 NC PIN 8 NC MODULE 476 178 RELAY OPT 02 MODULE 476 180 1 0 MODULE 476 777 VOIP PIN I RLY 1 COM PIN I RLY 5 COM PIN 1 0 PIN 1 1 0 9 PIN PIN PIN 2 RLY I NO PIN RLY 5 NO PIN 2 1 0 2 PIN 2 1 0 10 PIN 2 en MT f PIN jaw Ky PIN 3 RLY 2 COM PIN3 RLY 6 COM PIN 3 1 0 3 PIN 3 1 0 II PIN 3 PIN 3 PIN 4 RIY 2 NO PIN4 RLY 6 NO PIN 4 1 0 4 PIN 4 1 0 12 PIN 6 Jm RV PIs fu aw PIN 5 RLY 3 COM PINS RLY 7 COM PINS 1 0 5 PIN 5 1 0 13 PIN 4 PIN 6 RLY3 NO PING RLY 7 NO PIN 6 1 0 6 PIN 6 1 0 14 PIN 5 ETH SHD oig ms TA ai PIN 7 RLY 4 COM PINT NC PIN 7 1 0 7 PIN 7 1 0 15 PIN 7 PIN 7 PIN 8 RLY4NO PINS NC PIN 8 1 0 8 PIN 8 1 0 16 PIN 8 ETH SHLD pyg eum Starting the M4x Blade Software 1 Verify the M4x Blade is powered on 2 Connect the USB Cable to the M4x Blade as well as to the computer 3 Located on the Computer Desktop select M4x Setting shortcut 4 Once the program is open select Actions menu in the upper left are of the screen Select Connect Select Local USB On the right hand side of the screen a new box will appea
3. e M4x Blade by unplugging the unit and plugging it back in Rev E 2011 Configuring a Bridge 1 Configure the M4x Analog 4 Wire Module s before configuring a Bridge 2 The M4x Blade allows multiple bridge configurations to be created on one blade 3 Click System Bridging on the right side of the screen 4 Drag various ports from the system components panel and drop them onto the Port Name boxes in the Bridge Configuration pop up box If Broadcast is NOT checked the associated bridge group will be full conference If DTMF Bridge Group is enabled the members of the bridge are now able to be cross patched dynamically as remote users dial using DTMF enabled devices Please refer to the M4x User Manual for more detailed settings 5 Click the check box Enabled to enable the bridge Configuring SNR Voting Advanced Feature 1 Configure the M4x Analog 4 Wire Daughter Board s before configuring a Vote Group 2 Click System Voting on the right side of the screen 3 Follow the wizard that appears 4 Click the Add button to enable the Voting group Performing an M4x Loop Back Test for a 4 Wire Analog Module The M4x Loop Back Test enables users to perform basic tests for PTT and COR XMT and RCV tones as well as DI MF 1 Click Actions on the Menu upper left corner of screen Select Loop back Test Place the loopback cable firmly into a M4x Blade port to test Select
4. r Press the next to Communication System eee LO 1 a Click on Blade and factory settings will appear This screen will show the following The M4x Blade Firmware Revision The Modules Installed Firmware Revision Any enabled features 10 Click on the next to Blade and its Node Address The items that appear will allow you to access the port settings 11 Click on the next to System Voting to create a Vote Group or Groups an optional feature 12 Click on the next to System Bridging to create a Bridge Group or Groups Please refer to the M4x User Manual for more detailed settings Configuring the M4x Analog 4 Wire Module 1 Click on the just to the left of the Blade if you haven t already from prior instructions All ports populated will show a generic name until the user changes it 2 Click on the port that you want to analyze or configure The Port Status along with the Transmit and Settings control buttons appear 3 Press the Settings button in order to expand the settings screen 4 Click through the tabs to see various settings 5 When all changes have been made click Actions menu and then Save Settings to Firmware This will save the settings to the M4x Blade Please note the Save button only saves the changes on the computer and will not save the settings onto the M4x Blade 6 After any changes have been made please power cycle th
5. the port to test be sure the cable is in the same port Select the Loopback Tab Select to Test All or the Specific Test and click Test a Ok Ob oe Tee oD Testing status and Pass Fail notifications will populate as the M4x Blade goes through the specified tests Thank you for choosing a Raven Electronics M4x Blade for your Communication needs where we are the idea shop committed to solving engineering problems and exceeding expectations
6. wer Adapter can be connected to a 100 to 240 VAC 50 60 Hz 0 5A source 3 Connect the DC plug from the AC Power Adapter into the DC jack on the rear of the M4x Blade as shown in Figure 1 Figure 1 LED Indicators There are seventeen LED indicators on the front panel of the M4x Blade as shown in Figure 2 There are two LEDs per Port The first LED is Red default is XMT Output The second LED is Green default is RCV Input There is a Power On LED which is also Green to let the user know the M4x Blade is powered on Figure 2 For more details regarding how the LEDs can be set to indicate PTT E Lead or COR M Lead please refer to the M4x User Manual M4x Port Pin Outs On top of each M4x Blade there are labels with pin out information for each port installed in the M4x Blade Please note the pin order is grouped for clarity 12345678 Note E Lead is PTT M Lead is COR MODULE 476 150 4 WIRE INTERFACE MODULE 476 151 _4 WIRE INTERFACE zoe ade ade abe mo TH fpg FID ppa Few JHD i pa i l pan i pro fi pan yg e ye Fe my e ye Feum PINS J PINS J PINS J PINS J WWW RAVENCOMM COM MODULE 476 152 2 WIRE INTERFACE MODULE 476 175 SNI MODULE 476 178 RELAY PIN PIN PIN NC PIN NC PINT RLY INC PINT RLY 3 NC PIN 2 awe PIN 2 2WIRE PIN 2 NC PIN 2 NC PIN 2 RLY 1 COM PIN 2 RLY 3 COM PIN 3 PIN 3 PIN 3 NC PIN 3 NC PIN3 RLY I NO PIN3 RLY 3 NO PIN 6 jist PIN 6 jee
Download Pdf Manuals
Related Search