AEL-8310 User`s Manual
Contents
1. www tmatlantic com The following general safety precautions must be observed during all phases of operation service and repair of this instrument Failure to comply with these precautions or with specific warnings elsewhere in this manual violates safety standards of design manufacture and intended use of the instrument The manufacturer assumes no liability for the customer s failure to comply with these requirements Attention I Safety 1 Users should operate according to this manual 2 There is high voltage inside the instrument please avoid touching it directly 3 Please read the user manual carefully before you use the instrument to assure your safety 4 Ground the Instrument This product is provided with a protective earth terminal To minimize shock hazard the instrument chassis and cabinet must be connected to an electrical ground The instrument must be connected to the AC power supply mains through a three conductor power cable with the third wire firmly conn ected to an electrical ground safety ground at the power outlet 5 Keep Away From Live Circuits Operating personnel must not remove instrument covers Component rep lacement and internal adjustments must be made by qualified service person Do not split the components when power cable connected Under certain conditions dangerous voltages m ay exist even with the pow er cable removed To avoid in juries always disconnect power discharge circuits a2. A ALIAKOM Programmable DC Electronic Load AEL 8310 User s Manual www tmatlantic com www tmatlantic com SAFETY GUIDE This manual co ntains the pr ecautions necessary to ensure your personal safety as well as for protection for the products and the connected equipment These precautions are highlighted with a triangle WARNING symbol in this manual and are marked according to the danger levels as follows Danger AN It indicates that if appropriate precautions are not taken serious incidents of p ersonal injuries and deaths or significant damages or losses to the properties will be caused Caution It indicates that if appropriate precautions are not taken injuries or losses of properties will take place Note Remind you to pay particular attention to the important information related to the products disposal of products or the specific part of documents Warning A N Only qualified personnel are allowed to debug and operate this equipment The qualified personnel are specified as those personn el who carry out commissioning grounding and apply the volume identification to the circuits equipment and systems according to the available safety practices and standards Note Only when this product is tran sported stor ed assembled and installedin a proper way and operated and maintained according to the recommendations can it implement the functions properly and reliably 1i
3. Fig 1 2 Front view of DC electronic load Current voltage On Off state Power load setting value working mode CC CP CR represent constant current constant power constant resistance mode 0 9 The number keys Load on off Load ON OFF switch R set Setting resistance value I set Setting current value P set Setting power value Store Store current program Recall Recall a saved program Start Start a program Stop Stop running program Menu Menu function operation A The up moving key YF The down moving key www tmatlantic com 3 Rotary knob and function keys al The left moving key b The right moving key ESC Escape key OK Confirmation key Rotary knob The rotation dial Fig 1 5 Rotary knob and function keys 1 4 2 2 Back view Communication interface Power supply plug AC line voltage switch Fig 1 6 Back view The fuse can be changed easily by using a small flat screw driver Please use a fuse within the range of 0 3 0 5A www tmatlantic com Chapter 2 Operation 2 1 Connect the power supply to the electronic load ELECTRONIC LO Fig 2 1 Connect the power supply to the electronic load 2 2 Main functions 1 Constant current mode 2 Constant power mode 3 Constant resistance mode 4 Store a program 5 Recall a program 6 Start a program 7 Stop a program 8 Load On Off 2 2 1 Constant Current Mode In constant current mode the electronic load will sinka
4. Load Mode enter the load value and the duration of each program step The maximum program length is 10 steps But user may decided only run part of them Use the Run Steps push bar to decide how many steps you want to run Program State is used to define whether repeat to run this program When finishing press OK to store the program and go back to the main window Press Eil button to run the program press button to stop the program 2 11 Eload setting Click the p button the Eload setting window will be displayed Fig 2 16 The Eload Setting window 24 www tmatlantic com The Eload Registration Records show the parameters of all registered load To add a new load click the iss button MaxPoweqay 200 MarResisianesiGile ZOK Lf cancel Fig 2 17 Add new load window Enter the Eload Name Address and the maximum value of current power resistance then press OK to confirm Note the Eload ID is assigned by the software The Parameter Explanation l To delete a registered load select the load from the Eload Registration Records then click the button T Mody To modify a load s parameters select the load from the Eload Registration Records then click the button Or Caney To query a load click the button then enter the load name you want to query Attention after the Add Modify Delete operation the program must restart so that the modifications may
5. ee ba a amem k dinin TEF Fig 1 7 The installation option dialog box 1 2 7 The Select Program Folder dialog box displays Specify a program folder or leave the default folder then click Next Fig 1 8 The Select Program Folder dialog box 17 www tmatlantic com 1 2 8 Copy the files to your hard disk Fig 1 9 Copy Files Software installation is complete when finished 18 www tmatlantic com Chapter 2 Introduction 2 1 Running the program 2 1 1 To run the ElectronicLoad program select Start gt Program gt Eload and click E3710A or E3711A to run the program pi oll Ti L L E j Fha ES airis ER Ja ea ae Uns sra x N G RR RRR eee EO FES E Se e a s K TL A Fig 2 1 Start the program 19 www tmatlantic com 2 1 3 The ElectronicLoad Main Window a algi j J ary mareg en me a j a Co ee Fig 2 3 The ElectronicLoad Main Window 2 2 The ELoad List The Eload list lists all registered electronic load on the computer To make the ElectronicLoad control your load choose the load you want to use from the Eload list Fig 2 4 The Eload List 2 3 The Load Mode List From the Load Mode list you can select Load Mode Constant Current Constant Power Constant Resistance Load Mode Constant Corrent 9 Fig 2 5 The Load Mode List 2 4 Control Switch The Load On Off switch is to turn on off the
6. electronic load the Self PC Control switch is to set who control the electronic load the PC or the load itself 4 J m Fig 2 6 Control switch www tmatlantic com 2 5 The Tool Buttons On the top left of the main window there are 9 tool buttons Start Start communication Stop Stop communication Setting setting COM Port and recording interval Program Setting a Program Run Program Run a Program Stop Program Stop Running Program FREER Z R Eload Setting Setting load parameters i Report Data report Quit Quit the ElectronicLoad program E 2 6 Keypad and Rotary dial K w Fig 2 7 Current Power Resistance setting dial To quickly modify a parameter Current Power Resistance put the mouse on the red point of the dial and rotate To accurately set a parameter use the keypad Fig 2 8 Keypad 21 www tmatlantic com S Set Current Press I set input the current value 0 30A press ENTER to confirm Set Power Press P set input the power value 3710A 0 150W 3711A 0 300W press ENTER to confirm Set Resistance Press R set input the resistance value 0 500Q press ENTER to confirm I Max P Max R Max show the max value of each parameter 2 7 The Amp Power Resistance Voltage Meter The Amp Power Resistance Voltage Meter show the setting and read back value of current power resi
7. own keyboard In the event of communications failure please check the Com port baud rate and Address settings Also ensure that the communication cable is firmly and correctly connected 27 28 www tmatlantic com Chapter 3 Uninstall ElectronicLoad Software 3 1 Uninstall the ElectronicLoad Software From the Start Menu select Program gt Eload gt Uninstall Eload to unstall the software Remember to quit the program before uninstalling
8. 0 Press P set button for confirmation Set Power 30 0W Step 5 New 30 0 Step 6 Press ESC to go back to the main menu You can exit the power set operation at any point by pressing the ESC key 2 2 3 Constant Resistance Mode In constant resistance mode the electronic load will sink a current linearly proportional to the input voltage in accordance with the set value The resistance value can be set with the keyboard and or rotary knob Please see the following operation procedure www tmatlantic com Constant resistance setting procedure Press R set button Input Password Enter the password if the keyboard isn t locked please Input Password go to step4 KK KK Press the OK button the original set value will be Set Resis 200 0 Q displayed on the LCD It will return to step 2 if your N ew password is wrong Enter the new resistance value with the number keypad Set Resis 200 0 Q or rotate the dial to adjust the value New 50 00 Press R set button for confirmation Set Resis 50 00 Q New 50 00 Press ESC to go back to the main menu You can exit the resistance set operation at any point by pressing the ESC key 2 2 4 Store a program The ADG 8310 electronic load provides a program mode for dynamic testing The user can program the ADG 8310 electronic load and define the load values current power resistance and duration of every step For more details about the pr
9. 0 2 999A 0 2 3mA 3 00 30 00 0 2 30mA Free application software ElectonicLoad ActiveX control support Software VC VB DELPHI LABVIEW Program Memory 9 programs 10 steps each Over voltage over currat over power over heat polarity reverse AC Input 110 220V AC switch able 60 50HZ Software users manual AC power cable handlebars Voltage Accuracy www tmatlantic com 1 3 Features LCD display with backlight 2 High resolution measurement 3 CC CP CR mode 4 Number keypad and rotary knob 5 Multifunction menu 6 Over voltage over current over power over temperature polarity reversion protection 7 10 steps program 8 Compact and light weight 9 Can be used in parallel connection 10 Can be controlled by PC 1 4 Dimensions and Structure 1 4 1 Dimensions unit mm Fig 1 1 Dimension of Programmable DC electronic load www tmatlantic com 1 4 2 Structure 1 4 2 1 Front view Front panel is for users to operate and there is one LCD display one number keypad and one rotary knob Please see the following pictures 1 LCD display 7 mi EE l k 9 RI LE FEET 0 00gpA Fig 1 3 LCD Display of electronic load 2 Arrangement of the Keyboard In general the keyboard will perform the function of the black words Ist But in the 2nd mode it will perform the function of the words in blue aren Fig 1 4 Keyboard of DC electronic load
10. amming procedure is showed below 1 Select Program Set from menu operation the LCD will display Use the UP and DOWN keys or rotary knob to select Constant Current mode and press OK to confirm 2 LCD will display Input the program length 3 and press OK to confirm 3 LCD will display Input the current value 1 A then press OK to confirm 1 www tmatlantic com 12 4 LCD will display 5 LCD will display 6 LCD will display 7 LCD will display 8 LCD will display 9 LCD will display Input the time value 2 s then press OK to confirm Input the current value 2 A then press OK to confirm Input the time value 5 s then press OK to confirm Input the current value 3 A then press OK to confirm Input the time value 10 s then press OK to confirm Select Repeat then press OK to confirm The programming process is completed Press ESC to return to the main menu press Start to run the program If you want to store this program for later use please see 2 2 4 2 3 8 Save Option This function is used to save the last load setting current power and resistance before switching off ADG 8310 When this option has been set every time the user switches on ADG 8310 the previous load setting will be restored automatically Select the Save Option function
11. anged from the previous value according to the rotation At the beginning the cursor will be shown on the last number of the value which is indicated on the LCD you can move the cursor to the first number second number etc by using 4 and b buttons and then rotate to change each number and let it stay at 3 12 A www tmatlantic com 2 If the keyboard is locked Step1 Press I set button Step2 Enter the password by using the number keyboard Step3 Press OK button if the password is wrong please go to step2 for reentering Step4 Rotate the Rotary to change the value the operation is the same as item 1 Step5 Press I set button to confirm the current value 2 2 2 Constant Power Mode In constant power mode the load s current will increase automatically if the input voltage is decreased or vice versa so that the electronic load will sink a constant power in accordance with the set value The power value can be set with the keyboard and or rotary knob Please see the following operation procedure Constant power setting procedure Enter the password if the keyboard isn t locked please go to Input Password step4 ceed Press the OK button the original set value will be displayed Set Power 20 0W on the LCD It will return to step 2 if your password is wrong i ew Enter the new power value with the number keypad or rotate Set Power 20 0W the dial to adjust the value New 30
12. ccc s c220c0naierveasndbvsersedetsdevendecesscce RA RRR ARR ARR TEE TRAR RRR ZR ana 22 oD Va T eee pete e ade ameter cin eo eunon enue eee niente aa enue enue ee nace E ectanen pene ne encee eae ne ganenntan 22 IA E 11111 ee eee PE Dee LON gee OR E OEI E ere eT Oe ae eee ee ee een ee Teen 23 2 10 Programming Window onc 0ueecdeatawsindactiuniacsntaseheiceaedlaepaddideesstad EAE AEREE EEEE TE AREER 24 ALT ORES a A E A E EEE EE E E E 24 Die DER a a E E E E E T E E E 26 2 13 Use Electronicload software control your load issis cece ccc enn RR RER aA TAn EE EEE TN RKR 0 CN EEE dad R EERE EEE EEE 27 Chapter 3 Uninstall ElectronicLoad Sofware ssss sss sss sss s esse sss ss esse sse esasan aana a anen ea aaaeeeaa aeaaaee ae 28 yl Umastllike SIE E Lodd SOWA eresien ennie EE REENA EASE ERE EEEO Sram atornesrast 28 www tmatlantic com Chapter 1 General Introduction 1 1 General Introduction AEL 8310 electronic load is asingle input programmable DC electronic load It provides a convenient way to test DC power supplies and batterieslt offers constant current mode onstant resistance mode and constant power mode Program operation and control by PC is also available The backlight LCD numerical keypad and rotary knob make it much easier to use It is an essetial instrument for designing testing and manufacturing of many suitable products 1 2 Specifications mear iS 0 000 3 999V 0 2 3mV 4 00 35 999V 0 2 30mV 36 0 360 0V 0 2 300mV 0 00
13. constant current in accordance with the set value regardless of input voltage The current value can be set with the keyboard and or rotary knob Please see the following operation procedure www tmatlantic com Constant current setting procedure Enter the password if the keyboard isn t locked please go Input Password to step4 KKK K Press the OK button the original set value will be Set Curr 2 00A displayed on the LCD It will return to step 2 if your New password is wrong Enter the new current value with the number keypad or Set Curr 2 00A rotate the dial to adjust the value New 3 00 Press I set button for confirmation Set Curr 3 00A New 3 00 Press ESC to go back to the main menu You can exit the current set operation at any point by pressing the ESC key For example set constant current to 3 12A 1 Setting by number keyboard Step1 Press I set button Step2 Enter the password by using the number keyboard if the keyboard isn t locked please go to step4 Step3 Press OK button if the password is wrong please go to step2 for reentering Step4 Press 3 1 and 2 button to enter the current value Step5 Press I set button to confirm the current value 2 Setting by Rotary Knob 1 If the keyboard isn t locked press I set button then directly rotate the Rotary knob the current value will be continually ch
14. lect the Baud Rate by using the UP and DOWN keys or the rotary knob then press OK for confirmation 2 3 5 Setting Address 0 254 This function is used to set the address of the load To communicate with the computer or other equipment ADG 8310 load must be assigned an address When you select Address set function the LCD will display Set the address by using the number keyboard or the rotary knob and then press OK for confirmation The valid address range is from 0 to 254 10 www tmatlantic com 2 3 6 Enable disable the Rotary knob This function is to enable or disable the rotary knob Use the UP and DOWN keys or rotary knob to select and press OK to confirm 2 3 7 Program ADG 8310 electronic load provides a program mode for dynamic testing The user can program the ADG 8310 electronic load and define the load values current power resistance and duration of each program step To program the ADG 8310 please follow these 4 steps s Select one working mode constant current constant power constant resistance 2 Set the length of the program 3 Set the load value current power or resistance value and duration time of each step 4 Select program running mode one time or repeat For example you need to set the following program Constant Current mode Step 1 1A for 2 seconds Step2 2A for 5 seconds Step3 3A for 10 seconds Repeat running step1 to step3 Progr
15. ll pop up 4 Pull out the fuse change it according to the label beside the power input plug Warning To avoid damaging the instrument please be sure to change a suitable type fuse 111 www tmatlantic com Programmable DC Electronic Load Table of Contents PART1 AEL 8310 Electronic Load Chapter General Introduce ii iiis ccascitacdtnciacenadosessesavedsvasiassd ns taess pavhced wont eauwsistanadlenisaea E aaa 1 k rG ie Eaa e ge ect eh oro seed A E ote Sh wea eee nd ego se ated ype eaten ee Beet eae l M2 Rr TTT l 2 a PEE A E E O E E E E O E E T POE E O E E T 2 GAD eon BSC eE peers E E EEE A E 2 E SEB OIE ETE E E E EEE E EE TEE AENT EEI TE E E ET E eee 2 R Se T E E E E AE EEE E E 3 E Se N ST WAC WW EA AE EO EE TA EE E T TEE N VE E O E AETIA E EAT 3 E Sn he A A AET TE E TA E T E T A E AT 4 Chapter 2 Operaio TT 5 2 1 Connect the power supply to the electronic load aa ge conweeeastndensdindex HRA E E ARRE AR ETRETANT REAR TAE taa 5 POA TE tlc ee ee ee eee nr ee eee re er rere eT err eer Te O eet eee en ee errr EE 5 Talc oastant Current Mod eari enn Ene EE EEN EEE EAEE ESEE EE EEE EEE EAE EAEE 5 PA RS E PO r E EEE A E EREE 7 Dao Contant Feet Ve e TTT 7 RE SUONe A TTT 8 D2 RECA ARO TTT 9 gO SAN EOLA bebo ian iets TEE A A E A eines E epee via EE A E E EES T 9 Dl Ke ER e TTT 9 SR E CPA TTT 9 R VI Ot Oy ae cachet dace tates Beet enon et os rete tee E A ee ee see eae enone deer aaa S EE IOE 9 2 32 Seine The maximum CUPPING e onde
16. nd remove external voltage sources before touching components 6 Do Not Substitute Parts or Modify Instrument Because of the danger of introducing additional hzards do not install su bstitute parts or perform an y unauthorized modification to the instrument Return the instrument to a qualified dealer for service and repair to ensure that safety features are maintained II Connecting the power line 1 Inspect the power selection switch on the back panel to assure if the selected voltage is the same as environment power voltage If not please refer to the notice around the power plug 2 Before connecting the power supply please be sure that the switch on the front panel should be in the off position 3 Connect the p ower cable to the AC in the po wer supply and the 3 connector plug Please be sure that the AC power supply is grounded 4 Press the switch on the front panel to switch on the instrument and you can start to use it www tmatlantic com HI Fuse 1 The fuse is at the position of power input part on the back panel for the purpose of avoiding failure brought by using wrong voltage Please pay attention to the following items when you change the voltage input and the fuse 2 Before changing the voltage and fuse please be sure that the AC power is switching off and be sure that there is no other equipment connected to this instrument 3 Put a screwdriver into the fuse mounting press it and the fuse mounting wi
17. ogramming operation please refer to 2 3 7 User s program may be stored in nonvolatile memory for later use Up to 9 programs can be stored in ADG 8310 To store a program please follow this operation procedure Press Store button SAVE 1 S Enter the program number 1 to 9 by using the number SAVE tep key or the rotary knob Press the OK button for confirmation It will return Step 3 to Step 2 if the number is out of the range You can exit the store operation at any point by pressing the ESC key www tmatlantic com 2 2 5 Recall a program To recall a program stored in the ADG 8310 please follow this operation procedure Step 1 Press Recall button RECALL 1 Sica Enter the program number 1 to 9 by using the number RECALL tep key or the rotary knob Sinn Press the OK button for confirmation It will return tep to Step 2 if the number is out of the range You can exit the recall operation at any point by pressing the ESC key 2 2 6 Start a program Press Start button to run the current program 2 2 7 Stop a program Press Stop button to stop the running program 2 2 8 Load On Off The load s input can be toggled on off through the Load On Off key 2 3 Menu operation The Menu operation offers some setting and adjusting functions The operation and functions are as following Press Menu button The LCD displays the menu functions Use the UP and Ma
18. ou may choose RS 232 gt RS 485 adapter Fig 1 1 Connect the electronic load to PC 1 2 Installation 1 2 1 Insert software CD into the CD ROM drive double click My Computer gt CD gt Eload gt Setup exe to start the installation the Fig 1 2 will be displayed Proerammahle DHEU Electronic Load Fig 1 2 The Initialization of the Installation 15 www tmatlantic com 1 2 2 The Welcome dialog box displays press NEXT to continue 2 im I P A maa TE bea R a ee are a nn i be h eb Re nB L j J Fig 1 3 The Welcome dialog box 1 2 3 The License Agreement dialog box displays Click Yes to accept the License Agreement and proceed with the installation process Note If you do not want to accept the License Agreement click No to abort the installation process Fig 1 4 The License Agreement dialog box 1 2 4 The User Information dialog box displays Enter your name and your company s name then click Next Fig 1 5 The User Information dialog box 16 www tmatlantic com 1 2 5 The destination folder dialog box displays The default folder is C Program Files ELoad You may click Browse to select other installation path Fig 1 6 The destination folder dialog box 1 2 6 The installation option dialog box displays Select Typical to install all components or select Custom to select installation components P R m 8 B
19. stance and voltage 4 4 U HE Feadback Falus wala lalaa T cogggge s1aTs N 51818 BIRLE mnnn slaka mE fl Bit OA R s Ta re Lii TE m E mm ait Fig 2 9 The Amp Power Resistance Voltage Meter 2 8 Dynamic Curve These curve show the dynamic states of voltage and current Current Curve Voltage Curve 2 15 5 E 10 3 5 0 FA SS U SU 100 150 U 10 20 30 40 SU Fig 2 10 The Voltage Curve Fig 2 11 The Current Curve You may drag your mouse on the curve to zoom in out 22 www tmatlantic com 2 9 Setting 2 9 1 Setting Com port and baud rate Click the L button select the correct Com port and baud rate The baud rate setting should be the same as the connected electronic load Fig 2 12 Setting Window 2 9 2 Setting electronic load address Fig 2 13 Address Setting window Click Address to go to the Address setting window Set an address that is the same as the connected electronic load Press OK to confirm 2 9 3 Setting Recording Interval Fig 2 14 Setting Recording Interval window ZS www tmatlantic com 2 10 Programming Window ElectronicLoad allows user to make an own program to control ADG 8310 load User can select the load mode and define load value current power resistance and duration of each program step Click the ail button the Program window will be displayed Fig 2 15 Programming window Select an Electronic
20. take effect The following dialog box will be shown click Yes to close the program then restart the program from the Start menu 25 26 www tmatlantic com Information Ci Fig2 18 After Add Modify Delete operation the program must restart 2 12 Data Report Click the bes button the data report window will be shown NI b E R R III BHT Ao SH en LB LG A GB iA PA i i Fig2 19 The Data Report window To search set the query condition and then click the Search button Click the Report button to watch the report Click the Excel button to export the report in Excel format To delete historic data click the Clear button Quit quit to the main window www tmatlantic com 2 13 Use ElectronicLoad software control your load Start the ElectronicLoad program from the Eload List select the load you want to use If the desired load does not appear on the Eload List use Eload Setting to add the desired load Click the M Setting button ensure that the Com port baud rate and address is the same as that of the load Click the T Start button to start communication Using the Control Mode switch set the load in PC control mode You may now control the load from the computer Prior to quitting the ElectronicLoad program do remember to return the setting of your load to the Self control mode failing which you will be unable to control your load using it s
21. the LCD will display Use the UP and DOWN keys or the rotary knob to change the selection then press OK to confirm Select Save I P R and load setting will be saved before the unit is switched off and will be restored automatically when switched on the next time Select Don t Save def represent not to save current load setting www tmatlantic com 2 3 9 Lock the keyboard This function is used to lock the keyboard keep the load setting from unauthorized change Only the person with correct password is allowed to operate Select the Key Lock function the LCD will display Enter a 4 numbers password then press OK to confirm 2 3 10 Load Default This function is used to restore all the parameters to the factory setting Select Load Default function LCD will display Select Load Default and press OK to restore to the factory setting 2 3 11 Exit Select Exit to exit the menu operation 13 www tmatlantic com ElectronicLoad Software ElectronicLoad is a free software which allow the user to monitor and control the ADG 8310 electronic load 14 www tmatlantic com Chapter 1 Software Installation 1 1 Connect the electronic load to PC With the optional communication adapter you can connect ADG 8310 load to your computer through RS 232 USB or RS 485 port Connect ADG 8310 to a RS 232 port with adapter to a USB port to a RS 485 If your computer doesn t have an RS 485 port y
22. ween wecerades see lawcatun EAE E iis yen aa ea EE EE Eak 10 2 5 2 Setting Ihe MAXIMUM POW Els cc lt ccareniidaiceeiaaartagest tenets sd idedae devine Geeta dassauieassd suns E DATAE E EEA 10 2 0 0 selling Minimum Input Vola osc lt o ccayscnveswandeeuscetdieaokadesscsdeadaundnuelenetedacheancaiaeedebwandbeuednteueoiadadasnodees 10 R RET COO eee ee ENN ee ee eee ee ee E E ree eee ne eee eee 10 S SETE LU T as cetacean baa Sond ee ow eisink Leena da vnce baa pew eos Ledeen atom EEE 10 2 30 Enable 7 disable the Rotary KO D yaie teindavacesecectadianedssesasaskeneenedersheaed ida sadanedvactsabesesdhadesseadnaebieern eset acd 11 P A E ENEE E E A A EE E IEEE A E T AEE E OEE EAE EA IEEE EN 11 K AV e E A E E 12 2 507 Lock the Key boid ereman eea as a a aa 13 PAME HI E E IEE EE I PENS E E eee een s 13 IA EE AELE E PET E T Te E E E E ee 13 vi www tmatlantic com PARI 2 Electronice Load SOtwar TTT 14 Chapter L Software E ETT 15 L Conicet ihe clectonic load TTT 15 IR Rn a E EEPE AE AEE EE EE TEE E A O S E EIE NE AS E E E E E 15 Chapter 2 U RN U T HT 19 21 RGN OO TAIN L oe sa ecstatic es oe te eames enon eh aes n Ea ERa a bas E naaa E an E 19 OFA Waka Se EE conan eee eee eee E eee re ne ee ne A E ee eee eee ee 20 2a Tho Ebad Mode E TTT 20 A OE HOT E a A AEE E E E E 20 PR R I KT N 0G TTT 21 DOI Gy a0 AE IO bai T oo hades oc reece since ras ede sone E sae eed deen hak ee cea ca te ae ceeded cones 21 2 7 The Amp Power Resistance Voltage Meter
23. ximum Current Maximum Power Min Input Volt Band Rate Address Knob Enable Program DOWN keys to select a function then press OK for confirmation Save Option Key Lock Load Default Exit You can exit the menu operation at any point by pressing the ESC key www tmatlantic com 2 3 1 Setting the maximum current When you select the Maximum Current function the LCD will display Set the maximum current value by using the number keyboard or the rotary knob then press OK for confirmation 2 3 2 Setting the maximum power When you select the Maximum Power function the LCD will display Set the maximum power value by using the number keyboard or the rotary knob then press OK for confirmation 2 3 3 Setting Minimum Input Voltage This function is used to set the minimum input voltage when the input voltage is lower than this value ADG 8310 electronic load will automatically stop This function is used to discharge batteries When the battery s voltage drops down to the set value the load switches off automatically keeping the battery from over discharge When you select Min Input Volt function the LCD will display Set the minimum input voltage by using the number keyboard or the rotary knob then press OK for confirmation 2 3 4 Setting Baud Rate This function is used to set the communication baud rate When you select the Baud Rate function the LCD will display Se
Download Pdf Manuals
Related Search