Robotic Pool Cleaner K-Bot SX1
Contents
1. dry out before cleaning 6 1 Cleaning after use removing and cleaning the filter basket Open the filter cover Upon opening the filter cover the handle will lift independently KE AT DD N Y J Lift up the basket Open the latch HMS Clean the filter basket with a hose to release the bottom lid in order to remove the debris Robotic Pool Cleaner K Bot Saturn Series SX1 User Instructions 7 6 2 Periodic cleaning recommended at least once a month Dismantle the 2 ultra fine filter panels of the basket according to the following steps 3 ii i N q A HR SELS WUL El EEE WAN a pa Clean the filter panels with a hose Assemble the filter panels AN Insert the clean filter basket and close the filter cover Robotic Pool Cleaner K Bot Saturn Series SX1 Instructions User 7 CLEANING THE NET CANISTER Included with SX1 A Make sure the power supply is switched off and unplugged It is highly recommended to clean the net canister after each cleaning cycle Note Do not let the net c2. supply Minimum depth 0 80m 2 6ft Input 100 130 AC Volts 200 230 AC Volts Maximum depth 5m 16 4ft 50 60 Hertz Output lt 30 VDC IP 54 3 WARNINGS AND CAUTIONS 3 1 Warnings e Use the originally supplied power supply only e Ensure the electrical outlet is protected by a ground fault interrupter GFI or an earth leakage interrupter ELI e Keep the power supply out of standing water e Position the power supply at least 3m 10ft away from the edge of the pool Do not enter the pool while the Pool Cleaner is working e Unplug the power supply before servicing 3 2 Cautions Use the Pool Cleaner in the following water conditions only Chlorine Maximum 4 ppm pH 7 0 7 8 Temperature 6 34 C 43 93 F NaCl Maximum 5000 ppm 2 Robotic Pool Cleaner K Bot Saturn Series SX1 Instructions User 4 POOL CLEANER PARTS gt Robotic Pool Cleaner Model K Bot Saturn Series SX1 gt Power supply unit gt Filtration options Ultra Fine Filter Basket Filter Basket Net Panels Net Canister included with SX1 3 IND DE Robotic Pool Cleaner K Bot Saturn Series SX1 User Instructions 3 5 USING THE POOL CLEANER 5 1 Setup Before using the Pool Cleaner for the first time perform the following steps Position the power supply so Unwind the cable and stretch it out completely so that that it is approximately in the middle
3. the chemicals of the water Improper levels may allow the growth of algae making the walls slippery If so adjust the levels and scrub the walls Remove debris stuck in the impeller house or impeller cover according to the drawings Robotic Pool Cleaner K Bot Saturn Series SX1 User Instructions 11 Robotic Pool Cleaner K Bot SX1 a uto DOO Branch Locations CES Belmont Store Ph 08 9362 4022 Email perth autopool com au Melbourne Nunawading Store Ph 1300 656 956 Email melbourne autopool com au autopool Cee e Sydney Balkham Hills Store Ph 1300 656 956 Email sydney autopool com au Brisbane Archerfield Store Ph 07 3277 4958 Email brisbane autopool com au Scan Me www autopool com au www autopool com au
4. Robotic Pool Cleaner K Bot SX1 EN User Instructions p 1 8151665 EN Robotic Pool Cleaner K Bot Saturn Series SX1 User Instructions Contents 1 INTRODUCTION an 2 2 SPECIFICATIONS RS mou 2 3 WARNINGS AND CAUTI NSss nets 2 3 1 NATIF ne oi nement 2 Je CAIN etre tains tastsebenxsnnenstns 2 4 POOL CLEANER PARTS ss nn 3 5 USING THE POCILCEEANERS nee 4 51 SETUP nn antennes 4 5 2 Putting the Pool Cleaner into the pool n sssssssisseseeeee 5 5 3 Removing the Pool Cleaner from the pool 5 6 CLEANING THE FILTER BASKET etat 7 Gol Cleaning after US sinnerecspri nnii a 7 6 2 Periodic lens er 8 7 CLEANING THE NET CANISTER neeesser 9 Be CLEANING THE IMPELLER Sun us 10 9 ORF SEASON STORAGE sicrie atea 11 10 TROUBLESHOO ING a na a da 11 Robotic Pool Cleaner K Bot Saturn Series SX1 User Instructions Robotic Pool Cleaner K Bot Saturn Series SX1 User Instructions 1 INTRODUCTION Thank you for purchasing your new K Bot Pool Cleaner We are sure that your Robotic Pool Cleaner will provide you with reliable convenient and cost effective pool cleaning that includes filtration in all pool conditions with active brushing to enhance pool hygiene Robotic Pool Cleaners deliver advanced cleaning technology long lasting performance and easy maintenance You and your family will be free to enjoy your swim with full confidence that your pool is completely clean 2 SPECIFICATIONS Motor protection IP 68 Digital Power
5. anister dry out before cleaning 7 1 Cleaning after use removing and cleaning the net canister Lift up the net canister TARA Clean the net canister with a hose Robotic Pool Cleaner K Bot Saturn Series SX1 User Instructions 8 CLEANING THE IMPELLER If you notice debris trapped in the impeller A Make sure the power supply is switched off and unplugged 8 1 Clean the debris trapped in the impeller opening according to the following steps SAB Ifthe debris is not reachable follow the next Using a short steps screwdriver open the 2 screws Aa AN Pull the impeller cover backwards to release it Clean the debris trapped around the impeller Assemble the impeller cover 10 Robotic Pool Cleaner K Bot Saturn Series SX1 Instructions User 9 OFF SEASON STORAGE If the Pool Cleaner will not be in use for an extended period of time perform the following storage steps e Make sure that no water is left in the Pool Cleaner e Thoroughly clean the filter basket and panels canister and insert in place e Roll up the cable so that it has no kinks e Store the Pool Cleaner in a protected area out of direct sun rain frost at a temperature of between 5 45 C 41 113 F 10 TROUBLESHOOTING If the suggested solutions do not solve the problem please contact your dealer or Service Center Symptom The power supply or its switch led are not working Possible
6. it has no kinks of the long side of the pool at a distance of 3m 10ft Attach the floating cable to the power Plug in the power supply and leave it in the supply by inserting it with the notch on the OFF position connector 1 lined up with the groove in the socket on the power supply and turning clockwise 2 4 Robotic Pool Cleaner K Bot Saturn Series SX1 Instructions User 5 2 Putting the Pool Cleaner into the pool Put the Pool Cleaner into the pool Turn the power supply ON Release the Pool Cleaner and let it sink to the floor The Pool Cleaner will now operate until it has of the pool reached the end of the cleaning cycle Make sure that the floating cable is free of any obstructions 5 3 Removing the Pool Cleaner from the pool A Turn OFF and unplug the power supply 531 Robotic Pool Cleaner K Bot Saturn Series SX1 User Instructions 5 Using the floating cable bring the Pool Cleaner to the pool s edge Using the handle remove the Pool Cleaner from the pool A DO NOT PULL THE POOL CLEANER FROM THE POOL USING THE CABLE Place the Pool Cleaner on the edge of the pool and let the water drain out 6 Robotic Pool Cleaner K Bot Saturn Series SX1 Instructions User 6 CLEANING THE FILTER BASKET SX1 optional upgrade A Make sure the power supply is switched off and unplugged It is highly recommended to clean the filter basket after each cleaning cycle Note Do not let the filter basket
7. mpeller house or impeller cover e Remove debris stuck in the impeller house or impeller cover according to the drawings The Pool Cleaner moves but does not clean the pool e Clogged filter basket canister e Debris stuck in the impeller house or impeller cover e Clean the filter basket canister e Remove debris stuck in the impeller house or impeller cover according to the drawings The Pool Cleaner cleans only part of the pool e Power supply incorrectly positioned e Not enough floating is released for the correct operation of the Pool Cleaner e Place the power supply in a position so that the Pool Cleaner can freely reach all the pool area e Check that there is enough slack in the floating cable for the Pool Cleaner to reach all of the pool e Clean the filter basket canister The floating cable has kinks e Clogged filter basket canister e Debris stuck in the impeller house or impeller cover e Clean the filter basket canister e Remove debris stuck in the impeller house or impeller cover according to the drawings e To remove the kinks stretch the floating cable out completely and let it sit for at least a day in the sun The Pool Cleaner doesn t climb the walls e Clogged filter basket canister e Algae on walls e Unsuitable pH level e Debris stuck in the impeller house or impeller cover e Clean the filter basket canister e Check the level of
8. reason e No voltage in the power socket in the wall e The power supply is not switched ON e The power cable is not well connected into the power supply inlet Corrective action e Check that there is voltage in the power socket in the wall e Check that the power supply is plugged in and turned ON Check that the power cable is securely connected all the way into the power supply e Turn the power supply off Wait 30 seconds then turn it back on The Pool Cleaner does not move e The floating cable is not well connected into the power supply outlet e An obstacle blocks the impeller tracks or wheels e Check that the floating cable is securely connected all the way into the power supply Unplug the power supply Open the impeller cover and check that nothing is trapped in the impeller Verify that nothing blocks the tracks or wheels The Pool Cleaner is moving in circles e Clogged filter basket canister e Debris stuck in the impeller house or impeller cover e Power supply incorrectly positioned e Algae or pool water is out of Spec e Clean the filter basket canister Remove debris stuck in the impeller house or impeller cover according to the drawings e Place power supply in a position so that the Pool Cleaner can freely reach all the pool area e Correct pool and water conditions The Pool Cleaner does not turn or moves in one direction only e Debris stuck in the i
Download Pdf Manuals
Related Search