USER MANUAL / OPERATION INSTRUCTION
Contents
1. 55 56 63 OVERLAY TRIANGLES PROPELLOR SLANTED STAR MORAY RADIOACTIVE SINGLE SPIRAL 64 71 72 79 80 87 88 95 96 103 Oo A 1 N O Nn n N N oo o CH 5 PAN 0 255 co N N oa oa WHITE GOBO 1 GOBO 2 GOBO 3 GOBO 4 GOBO 5 GOBO 6 GOBO 7 POSITIVE RAINBOW clockwise scroll NEGATIVE RAINBOW counter clockwise scroll 360deg 8 bit prism 116 239 16 128 270deg 8 bit WHITE PRISM ROTATION Decreasing speed STOP STATIC PRISM MOTORIZED FOCUS zoom in zoom out SHUTTER CLOSED DIMMER CONTROL WHITE STROBE EFFECT increasing RESET after 5 seconds SHUTTER OPEN CH 10 RS fo 255 IRIS OPEN TO CLOSE CH 11 LAMP 0 5 LAMP ON Delay after 10 minutes 200 210 LAMP OFF after 5 second CH 12 SPEED 0 255 X Y CONTROLLABLE SPEED CH 13 PAN 16 0 255 MOTOR SPEED PAN 16 bit CH 14 TILT 16 0 255 MOTOR SPEED TILT 16 bit FIXTURE LCD buttons Down decrease key Control Board 9 8 8 Mode select Function up dn md Up increasing key 10 0 1 EI mode light 1 EI mode light 2 p mode sound Eqs mode slave 1 pg mode slow Eis Mode slave 2 Bey este mode stby ys Mode slave 3 PII des time hour EI nekoi Aa m Mode Positive t M Mode Positive PRA H Mode negative g Mode negative PIE ma Positive Display pa Negative Display 1 Pan Mode Positive Normal operation When you press the Pan1 and2. resistor between Signal and Signal into a 3 pin XLR plug and plug it in the DMX output of the last fixture OPERATION After you connected the fixture to the mains the PROMOVER 575 starts running resetting During the Reset the motors are trimmed and the device is ready for use afterwards Note You will here clicking noise That is each of the motors stepping through sequence to find each 0 starting position This is normal Stand Alone operation In the Stand Alone mode the PROMOVER 575 can be used without controller You can do without a controller as the PROMOVER 575 features a built in microphone which provides automatic sound control Disconnect the PROMOVER 575 from the controller and select Master Mode Sound control Master Slave operation Connect the master and slave devices and adjust the settings as described above Please note If you wish to change from one operating mode into another you have to unplug the PROMOVER 575 from the mains and plug it again DMX controlled operation You can control the projectors individually via your DMX controller Every DMX channel has a different occupation with different features In order to call up the different features you first have to open the shutter control channel 9 DMX value 132 139 or 250 255 or set the dimmer to the desired intensity control channel 6 DMX value 6 128 Addressing The Control Board on the front side of the base allows you to
3. under high working places and other endangered areas is forbidden The operator has to make sure that safety relating and machine technical installations are approved by an expert before taking into operation for the first time and after changes before taking into operation another The operator has to make sure that safety relating and machine technical installations are approved by an expert after every four year in the course of an acceptance test The operator has to make sure that a skilled person approves safety relating and machine technical installations once a year Procedure The device should be installed outside areas where persons may walk by or be seated IMPORTANT OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE including but not limited to calculating working load limits installation material being used and periodic safety inspection of all installation material and the device If you lack these qualifications do not attempt the installation yourself but instead use a professional structural rigger Improper installation can result in bodily injury and or damage to property The device has to be installed out of the reach of people If the device shall be lowered from the ceiling or high joists professional trussing systems have to be used The device must never be fixed swinging freely in the room Caution Devices in hanging installations may cause severe injuries if not properly mounted and secured correctly with ap
4. Pan2 their starting off point of Pan will be different 2 Pan Mode Negative mirror image the Starting off point of Pan1 the end point of Pan2 the Jumping off point of Pan2 the end point of Pan1 3 Tilt Mode Positive Normal operation When you press the Tilt 1 and Tilt 2 their starting off point of Tilt will be same seldom ever used 4 Tilt Mode Negative Also same as Pan seldom ever used 5 LED Positive Display When leaving on floor mounted or on test bench as shown 6 LED Negative Display When you reverse the unit if you make LED Negative Display then it s more convenient to see the display when upside down and mounted For address setting Press the Mode button until the display shows d and set the desired base address via the Up Down buttons Controlling After having addressed all PROMOVER 575 you may now start operating these via your lighting controller Note After switching on the PROMOVER 575 will automatically detect wnether DMX 512 data is received or not If the data is received the control LED flashes If there is no data received at the DMX input the control LED lights up permanently This situation can occur if The 3 PIN XLR plug cable with DMX signal from controller is not connected with the input of the PROMOVER 575 or having a bad connecting cable The controller is switched off or defective if the cable or connector is defective or the signal wires are swapped reversed in the input connec
5. assign the DMX fixture address which is defined as the first channel from which the PROMOVER 575 will respond to the controller If you set for example the base address to channel 1 the PROMOVER 575 will use channels 1 to 14 for control Next available DMX value would be set for 15 Please be sure that you don t have any overlapping channels in order to control each PROMOVER 575 correctly and independently from any other fixture on the DMX data link If two three or more PROMOVER 575 are addressed similarly they will work similarly Before you attempt to operate this unit make sure you have no unanswered questions PROMOVER 575 CHANNELS COLOR 24 31 32 39 40 47 48 55 56 63 64 127 H 2 ROTATING 32 47 48 63 64 79 80 95 96 111 O N wo 7 7 oj N N Oo N 1 Kj al a Oo CO N al gt N WHITE PINK YELLOW BLUE ORANGE GREEN LIGHT PINK LIGHT PURPLE GRADUAL COLOR CHANGE POSITIVE RAINBOW EFFECT w increasing speed REGRESSIVE RAINBOW w decreasing speed CIRCLE SPIRAL BREAKOUT HAZARD DESIGN TRIANGLE FIRE SUN POSITIVE RAINBOW EFFECT w increasing speed REGRESSIVE RAINBOW w decreasing speed STOP N a ofj N N N oj o ay H 3 GOBO 0 15 ROTATE 16 135 136 255 H 4 0 7 8 15 SPEED GOBO CLOCKWISE right to left SPEED GOBO counter CLOCKWISE left to right RING HAND D N wo 24 31 32 39 40 47 48
6. INSTRUCTIONS For your own safety please read this user manual carefully before your initial start up Every person involved with the installation operation and maintenance of this device has to be qualified follow the instructions of this manual consider this manual to be part of the total product keep this manual for the entire service life of the product pass this manual on to future owners or users of this product include every supplementary update with the original manual If the device has been exposed to drastic temperature fluctuation e g after transportation Do NOT switch it on immediately Allow fixture to reach normal room temperature By not doing so the water condensation might damage your device and cause severe damage to lamp and circuit boards Leave the device switched off until it has reached room temperature This device falls under protection Class I The power plug must only be plugged into a protection Class outlet Never let the power cord come into contact with other cables Handle the power cord and all connections to the mains with particular caution Make sure that the available voltage is not higher than stated on the rear panel Make sure that the power cord is never crimped or damaged by sharp edges Check the device and the power cord from time to time Always disconnect from the mains when the device is not in use or before cleaning it Only handle the power cord by the plug
7. Never pull out the plug by tugging the power cord 2 During the initial start up some smoke or smell may arise This is a normal process and does not necessarily mean that the device is defective Caution During the operation the housing becomes very hot Do not switch the device On and Off in short intervals as this would reduce the lamp s life Keep away from children and non qualified users OPERATING DETERMINATIONS This device is a lighting effect for creating decorative entertainment lighting effects This product is only allowed to be operated with an alternating voltage of 120 V 60 Hz and was designed for indoor use only This device is designed for professional use on stages in discotheques theatres etc Lighting effects are not designed for permanent operation Consistent operation breaks will ensure that the device will serve you for a long time without defects Do not shake the device Avoid brute force when installing or operating the device When choosing the installation spot please make sure that the device is not exposed to extreme heat moisture or dust There should not be any cables lying around You endanger your own and the safety of others The symbol m determines the minimum distance from lighted objects The minimum distance between light output and the illuminated surface must be more than 0 5 meters This device is only allowed for suspended installation via the mounting bracket In order to
8. PROMOVER 575 USER MANUAL OPERATION INSTRUCTION MLSC Inc P 0 Box 578 Madison Al 35758 SHIPPING 8000 MADISON PIKE MADISON ALA 35758 PHONE 256 461 8000 FAX 256 461 7708 www meteor global com www meteor usa com e mail sales meteor usa com 1 PROMOVER 575 DMX Scanner INTRODUCTION Thank you for having chosen METEOR KLS PROMOVER 575 You will see you have acguired a powerful and versatile device lt nas been designed to be very flexible and user friendly without compromising effectiveness or professionalism Unpack your PROMOVER 575 Before you initial start up please make sure that there is no damage caused by transportation Should there be any guestions or problems consult your dealer and do NOT use the device SAFETY INSTRUCTIONS notes written in this user manual CAUTION Be careful with your operations With a dangerous voltage you can suffer a dangerous electric shock when touching the wires This PROMOVER 575 has left our premises in absolutely perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and follow all the warnings Important Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems CAUTION Keep this device away from rain and moisture Unplug mains lead before opening the housing SAFETY
9. able of this device becomes damaged it has to be replaced by a special power supply cable available at your dealer Should you have further questions please contact your dealer Please note All information is subject to change without prior notice MLSC Inc P O Box 578 Madison Al 35758 SHIPPING 8000 MADISON PIKE MADISON ALA 35758 PHONE 256 461 8000 FAX 256 461 7708 www meteor global com www meteor usa com e mail sales meteor usa com 12
10. bviously damaged so that its function is impaired e g due to cracks or deep scratches The objective lens will reguire weekly cleaning as smoke fluid tends to building up residues reducing the light output very guickly The cooling fans should be cleaned monthly The gobos may be cleaned with a soft brush The interior of the fixture should be cleaned at least annually using a vacuum cleaner or an air jet The dichroic color filters the gobo wheel and the internal lenses should be cleaned monthly To ensure a proper function of the gobo wheel we recommend lubrication in six month intervals Carefully placed quantity of oil must not be excessive in order to avoid that oil runs out when the gobo wheel rotates There are no serviceable parts inside the device Maintenance and service operations are only to be carried out by authorized dealers Please refer to the instructions under Jnstalling Replacing the lamp Replacing the fuse If the fine wire fuse of the device fuses only replace the fuse by a fuse of same type and rating Before replacing the fuse always unplug mains lead power cable Procedure Step 1 Step 2 Step 3 Step 4 Open the Fuse holder on the rear panel with a slotted screwdriver below power Remove the old fuse from the fuse holder Install the new fuse in the fuse holder Replace the fuse holder in the housing Should you need any spare parts please use genuine parts If the power supply c
11. ccess it if needed Table of contents INTRODUCTION aaa SAFETY INSTRUCTIONS aaa OPERATING DETERMINATIONS 055 USER MANUAL INSTRUCTIONS 0 DESCRIPTION OF THE DEVICE a FEATURES mt n t Sata cheat Gitex Kas OND o OVERVIEW INSTALLATION lt c z assistant Installing Replacing the lamp aaa kamp adjustm nt zxctssea asadasas sastatnes Master Slave operation 1 a DMX 512 connection connection between Fixtures Connection with the mains ccceeeeeeeeee ees O lt 0 S5 D D a J OG Q 5 Ke NNNOOOH OPERATION 3 neskar pasaukt keisu Stand Alone operation iii a DMX controlled operation diii aa Addressing sevis a e retas DMX PF01000 7xe sasar aada AEREE ProMover 575 channel features da Setting DMX Channel Stand alone LCD CLEANING AND MAINTENANCE c eeeeeeeeees 11 Replacing the fUS8 xx6eessadesl Lessszo ss dzeessgsusvoasssei ausgsd 12 TECHNICAL SPECIFICATIONS Power supply 115 V AC 60 Hz 500 W 6 Power consumption 800w DMX control channels 14 channels DMX 512 connection 3 pin XLR Sound control via built in microphone Strobe Flash rate 1 10 flashes sec via shutter Number of colors 16 dichroic white RAINBOW effect Number of gobos 14 rotating gobos and open rainbow scrolling Dimensions 16L x 13w x 20h 500 x 485 x 615
12. d tighten the safety screw The maximum drop distance must never exceed 20 cm A safety rope chain which already held the strain of a crash or which is defective must not be used again Adjust the desired inclination angle via the mounting bracket and tighten the fixation screws DANGER TO LIFE Before taking into operation for the first time the installation has to be approved by an expert Connection with the mains Connect the device to the mains with the enclosed power supply cable DMX 512 connection connection between fixtures The wires must not come into contact with each other otherwise the fixtures will not work at all or will not work properly Only use a stereo shielded cable and 3 pin XLR plugs and connectors in order to connect the controller with the fixture or one fixture with another Occupation of the XLR connection If you are using controllers with this occupation you can connect the DMX output of the controller directly with the DMX input of the first fixture in the DMX chain If you wish to connect DMX controllers with other XLR outputs 5 pin you need to use adapter cables Building a serial DMX chain Connect the DMX output of the first fixture in the DMX chain with the DMX input of the next fixture Always connect one output with the input of the next fixture until all fixtures are connected 7 Caution At the last fixture the DMX cable has to be terminated with a terminator Solder a 120 ohm
13. mm Weight 62 Ibs 24kg Boxed weight 71lbs Maximum ambient temperature ta 45 C Maximum housing temperature tB steady state 60 C Min distance from flammable surfaces 0 5 m Min distance to lighted object 0 5 m Fuse 10 amp Fitting lamp HMI 575 DESCRIPTION OF THE DEVICE Features Innovative Professional scanner with rotating gobos 16 different dichroic color filters and white Rainbow effect with adjustable speed in both directions Gobowheel with 14 rotating gobos open and blackout Strobe effect with adjustable speed 1 10 flashes sec via shutter DMX controlled operation or stand alone operation with Master Slave function Sound controlled via built in microphone Fuzzy Sound Control program continues automatically during periods without music or bass beat Control Board with 4 digit LCD display Digital DMX focus For HMI 575 Actual Lamp Hours User time DMX control via every standard DMX controller 14 DMX control channels reguired DANGER TO LIFE Only install the lamp with the device switched off And not plugged into power Always unplug power from mains before attempting any service For the installation you need one HMI 575 Do not touch glass part of lamp The lamp must only be changed when wearing appropriate protective clothing protection glasses protection gloves helmet with sight leather apron INSTALLATION Installing Replacing the lamp Procedure CAUTION The lamp has
14. propriate back up failsafe rigging If you have doubts concerning the safety of a possible installation DO NOT install the device Before rigging make sure that the installation area can hold a minimum point load of 10 times the device s weight Master Slave operation The master slave operation enables that several devices can be synchronized and controlled by one Master device unit On the rear panel of the PROMOVER 575 you can find an XLR jack DMX Out and an XLR plug DMX In which can be used for connecting several devices Choose the device that is to control the effects This device then works as master device and controls all other slave devices which are to be connected to the master device via a balanced microphone lead Connect the DMX OUT jack with the DMX IN plug of the next device Set the desired Master mode for the master device Set the respective Slave mode for all slave devices DANGER OF FIRE When installing the device make sure there is no highly inflammable material decoration articles etc within a distance of min 0 5 m Mount the device to your trussing system using an appropriate clamp For overhead use always install a safety rope chain that can hold at least 12 times the weight of the fixture You must only use safety ropes with quick link with screw cap Pull the safety rope through the attachment eyelet and over the trussing system or a safe fixation spot Insert the end in the quick link an
15. safeguard sufficient ventilation leave 50 cm of free space around the device Make sure that the area below the installation place is blocked off when rigging derigging or servicing the fixture Always secure the fixture with an appropriate safety rope and proper rigging hardware designed to hold more than 10 times the weight of the fixture proper industry standard Never look directly into the light source as sensitive persons may suffer an epileptic shock The maximum ambient temperature t 45 C must never be exceeded Operate the device only after having become familiar with its functions Do not permit operation by persons not qualified for operating the device Most damages are the result of unprofessional operation Please use the original packaging if the device is to be transported Please consider that unauthorized modifications on the device are forbidden due to safety reasons and will void any warranty Never remove the serial barcode from the device as this would make the warranty void If this device will be operated in any way different to the one described in this manual the product may suffer damages and the warranty becomes void Furthermore any other operation may lead to dangers like short circuit burns electric shock and lamp explosion Lamps and fuse replacements are not covered under warranty USER MANUAL ProMover 575 DMX Scanner Yoke Fixture Keep this manual for future needs Put it in a place that you can a
16. ter and set the dimmer intensity to 100 and focus the light on a flat surface wall Center the hot spot the brightest part of the beam using the 3 adjustment screws A B C Turn one screw at a time to drag the hot spot diagonally across the projected image If you cannot detect a hotspot adjust the lamp until the light is even To reduce a hot spot pull the lamp in by turning all three screws A B C clockwise 1 4 turn at a time until the light is evenly distributed If the light is brighter around the edge than it is in the center or if light output is low the lamp is too far back in the reflector Push the lamp out by turning the screws A B C counterclockwise 1 4 turn at a time the light is bright and evenly distributed Overhead Rigging if the main attachment fails as a secondary back up DANGER TO LIFE Please consider the DIN 15560 and the respective national norms during the installation An authorized dealer must only carry out the installation The installation of the device has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation The installation must always be secured with a secondary safety attachment e g an appropriate catch net This secondary safety attachment must be constructed in a way that no part of the installation can fall down When rigging or derigging or servicing the device staying in the area below the installation place on bridges
17. to be replaced when it is damaged or deformed due to the heat The lamp life given by the manufacturer must never be exceeded This is why you need to take notes on the operational time of the lamp and replace the lamp in time Keep exchanged lamp in a protective container and remove accordingly During the operation the lamp reaches temperatures of up to 600 C Before replacing the lamp unplug mains lead and let the lamp cool down approx 10 minutes During the installation do not touch the glass bulbs barehanded Please follow the lamp manufacturer s notes Do not install lamps with a higher wattage Lamps with a higher wattage generate temperatures the device was not designed for Damages caused by non observance are not subject to warranty Step 1 Unscrew the 4 Phillips screws on back plate Unscrew 4 Phillip head screws that hold lamp housing system to fixture and carefully remove it from the housing Step 2 If replacing the lamp remove the old lamp from the lamp holder Step 3 Insert the lamp into the lamp holder Make sure lamp is properly secured in brass fitting Step 4 Replace the lamp system in the housing and tighten the fixation screws Step 5 Adjust the lamp as described under lamp adjustment Do not operate this device with opened cover Lamp adjustment The lamp holder is aligned at the factory Due to differences between lamps fine adjustment may improve light performance Strike the lamp open the shut
18. tor Note It s necessary to insert the XLR termination plug with 120 Ohm in the last lighting in the link in order to ensure proper transmission on the DMX data link CLEANING AND MAINTENANCE The operator has to make sure that safety relating and machine technical installations are Inspected by an expert after every four years in the course of an acceptance test The operator has to make sure that safety relating and machine technical installations are inspected by a skilled person once a year The following points have to be considered during the inspection 1 All screws used for installing the devices or parts of the device have to be tightly connected and must not be corroded 2 There must not be any deformations on housings fixations and installation spots ceiling Suspension trussing 3 Mechanically moved parts like axles eyes and others must not show any traces of wearing e g material abrading or damages and must not rotate with unbalances 4 The electric power supply cables must not show any damages material fatigue e g porous cables or sediments Further instructions depending on the installation spot and usage have to be adhered to by a skilled installer and any safety problems have to be removed Disconnect from mains before starting maintenance operation 11 We recommend a freguent cleaning of the device Please use a moist lint free cloth Never use alcohol or solvents The lens has to be replaced when it is o
Download Pdf Manuals
Related Search