BCH9212-CN
Contents
1. Figure 5 either one or two piece base first make sure the side marked Rear is facing the back of the heater Line up holes of the base with holes on bottom of pedestal or heater housing if no pedestal is included and secure with 4 provided screws Refer to Figure 4 Step 3 Lace the power cord through the cord minders on the underside of the base Refer to Figure 5 Step 4 Turn the heater right side up on a flat level surface prior to beginning operation Remote Control if applicable If your heater comes with a remote control unpack the remote control from box This includes one lithium battery R2025 3V Please note this remote control will not work through walls Remove battery before discarding the remote NOTE REMOVE THE PROTECTIVE COVER FROM THE BATTERY PRIOR TO BEGINNING OPERATION Battery Replacement 1 Locate the battery compartment on the back of the remote control handset Insert a small object such as a pin or paper clip into the hole of the battery cover lock see Figure 6 and slide out the battery cover Remove old battery Place new battery into battery compartment Slide battery compartment into the remote control co PO Figure 6 A Battery Cover Lock B Battery cover handset until the Battery Cover Lock is securely latched 5 For your convenience a remote control holder is integrated into the back of the heater housing NOTES e Remove the battery from2. OTE Settings and control buttons may vary slightly between models S Fon Only Setting Press the Fan Only Button to run the heater without heat output The Stay On icon will appear on the LCD Display Max HIGH Heat Setting Press the Max Heat Button to run the heater continuously at 1500W The Stay On icon will appear on the LCD Display Basse LOW Heat Setting if applicable Press the Low Heat Button to run the heater continuously at 750W The Stay On icon will appear on the LCD Display Heat cigs e aSave Heat amp Save Setting if applicable Press the Heat amp Save Button to activate the energy Figure 7 2P BIONAIRE 2 BIONAIRE A Control Buttons B LCD Display C Dial Wheel D Power Light E Remote Control if applicable efficient Heat amp Save Mode The heater will now cycle between high at 1500W and low at 750W heat settings to provide heat The Stay On icon will appear on the LCD Display E Thermostat Control Your heater is equipped with a digital thermostat that allows you to set your heater to a precise comfort level by turning the Dial Wheel on the control panel or pressing the arrow buttons on the remote control if applicable NOTE If your heater comes with a Thermostat Button on the control panel or remote control if applicable you may either pres
3. P BIONAIRE pure indoor living HEATER WITH ADVANCED DIGITAL THERMOSTAT Fan Forced Heaters may appear with a different grill design NOTE A Phillips screwdriver is required for assembly Instruction Leaflet Read instructions before operating Retain for future reference l Questions Comments Call 1 800 253 2764 in North America PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS When ving electrical appliances basic safety precautions should always be ollowed to reduce the risk of fire electric shock and injury to persons including the following l 2 3 _ _ 12 DO NOT operate heater with a damaged cord or plg or Read all instructions before using the appliance To avoid fire or shock hazard Ag the appliance directly into a 120V AC electrical outlet The heater is hot when in use To avoid burns DO NOT let bare skin touch hot surfaces If provided use handles when moving this heater Keep combustible materials such as furniture pillows bedding papers clothes and curtains at least 3 ft bs m from the ar of the heater and keep them away from the sides and rear DO NOT run cord under carpeting DO NOT cover cord with throw rugs runners or t el e Arrange cord away from traffic area and where it will not be tripped over This heater is not intended for use in bathrooms laundry areas and similar indoor location NEVER locate heater where it may fall into a bathtub or other wa
4. Products Inc doing business as Jarden Consumer Solutions or if in Canada Sunbeam Corporation Canada Limited doing business as Jarden Consumer Solutions collectively JCS warrants that for a period of one year from the date of purchase this product will be free from defects in material and workmanship JCS at its option will repair or replace this product or any component of the product found to be defective during the warranty period Replacement will be made with a new or remanufactured product or component If the product is no longer available replacement may be made with a similar product of equal or greater value This is your exclusive warranty Do NOT attempt to repair or adjust any electrical or aoka functions on this product Doing so will void this warranty This warranty is valid for the original retail purchaser from the date of initial retail purchase and is not transferable Keep the original sales receipt Proof of purchase is required to obtain warranty performance JCS dealers service centers or retail stores selling JCS products do not have the right to alter mody or any way change the terms and conditions of this warranty This warranty does not cover normal wear of parts or damage resulting from any of the following negligent use or misuse of the product use on improper voltage or current use contrary to the operating instructions teas y repair or alteration by anyone other than JCS or an authorized JCS service center F
5. call 1 800 253 2764 and a convenient service center address will be provided to you In Canada If you have any question regarding this warranty or would like to obtain warranty service please call 1 800 253 2764 and a convenient service center address will be provided to you In the U S A this warranty is offered by Sunbeam Products Inc doing business as Jarden Consumer Solutions located in Boca Raton Florida 33431 In Canada this warranty is offered by Aiea Corporation Canada Limited doing business as Jarden Consumer Solutions located at 20 B Hereford Street Brampton Ontario L6Y OM1 If you have any other problem or claim in connection with this product please write our Consumer Service Department PLEASE DO NOT RETURN THIS PRODUCT TO ANY OF THESE ADDRESSES OR TO THE PLACE OF PURCHASE
6. device to control the room temperature Do not use this heater in small rooms when they are occupied by persons not capable of leaving the room on their own unless constant supervision is provided SAVE THESE INSTRUCTIONS TECHNICAL SPECIFICATIONS e Amps 12 5 Wattage 1500W 5 10 e Working voltage 120V AC 60Hz NOTE Low Heat setting may be 1000W on some models ASSEMBLY INSTRUCTIONS NOTE A Phillips screwdriver is required for assembly Unpack your heater from the box being careful to remove all parts from plastic bags and remaining packaging Please save the carton for off season storage Some models are packed with separate base and pedestal in the box Carefully remove all parts from plastic bags To prevent scratches place all parts onto a doth before assembly Follow the below instructions for Pedestal Base assembly Pedestal Assembly if no pedestal is included in this model move to Base Assem Wy Step 1 Run the power cord through the center of the assembled pedestal Snap pedestal into the bottom of the heater housing Refer to Figure 1 2 Base Assembly Step 1 If the base is in two halves snap them together y Sliding slots of one base half into slots of second hase half Refer to Figure 3 Step 2 Run the power cord through the center of the assembled base To assemble the base to the unit Figure 1 Figure 2 Figure 3 Figure 4
7. eater again and ensure to allow sufficient time for the thermostat to cool down FOR MODELS WITH TIP OVER PROTECTION Tip Over Shut Off When the unit is accidentally knocked over it will instantly shut off and the Power Light will flash The unit iiy also shut off if it is moved or bumped To reset simply place the heater in an upright position the Power Light will stop flashing and it will operate normally NOTE If unit does not turn on when placed in the upright position press Power On Off Button once and heater will resume operation TROUBLE SHOOTING General Information Environmental Factors There are a number of factors that will affect your desired comfort level These factors can include insulation open or drafty doors and windows and outside temperature Please check and take action if any of these potential problems are affecting your heaters ability to adequately warm your room Supplemental Heat Portable electric heaters are intended for supplemental heating of rooms to heat the room your in and turn down the central heat thermostat They are not intended to replace central heating systems Do NOT attempt to repair or adjust any electrical or mechanical functions on this heater Doing so will void warranty The inside of the heater contains no user serviceable parts All servicing should be performed by qualified personnel only If you have any questions regarding your product or would like to learn more about other B
8. heater Max and Low Heat amp Save settings control the heat output of the heater and not the fan speed Fan runs at the same speed on all settings You may hear a popping or crackling sound as the heater i up This is normal and safe operation Once the heater heats up the crackling sound will go away There may be an odor or vapor coming from the heater the first time you use it or after prolonged or seasonal storage Y Y Change battery Disc type 3 volt R2025 Remote works up to 20 feet 6m V Be sure to point remote at control panel on heater Y Y and there are no obstructions Make sure display panel is dean Raise the temperature higher or change setting to Low Heat amp Save or Max Press the Max or Low Heat amp Save Buttons Press the Power Button to turn on the heater Run heater in Max for maximum heat output If the noise persists call Bionaire at 1 800 253 0764 This is normal and is the result of dust or other debris accumulating on the heating element Make sure the heater is in a well ventilated area and continue running until the odor or vapor goes away 2014 Sunbeam Products Inc doing business as Jarden Consumer Solutions All rights reserved Imported and distributed by Sunbeam Corporation Canada Limited doing business as Jarden Consumer Solutions 20 B Hereford Street Brampton Ontario L6Y 0M1 Printed In China 1 YEAR LIMITED WARRANTY Sunbeam
9. ionaire products please contact our Consumer Service Department at 1 800 253 2764 or visit our website at www bionairecanada com For inquiries regarding recycling and proper disposal of this product please contact your local waste management facility Troubleshooting for your Heater Trouble Probable Cause p Solution O e Heater Does Not Turn On e Power Light is Flashing or in some cases Heater Turns On at Max Heat setting but then Shuts Off in 2 seconds with Power Light Flashing Not Enough Heat Heater cycles ON and OFF frequently Timer Activated only applicable on models with Timer feature Tip over switch engaged only applicable on models with Tip over protection Manual user reset is activated Not plugged in properly Electrical outlet does not hold plug in securely Thermostat set too low Obstruction causing the heater not to operate Circuit breaker trips Auto Safety Shut off system is activated when there is potential overheat Tip over switch engaged only applicable on models with Tip over protection Heater is in Low or Fan Only setting Thermostat set too low The thermostat automatically turns the heater on and off to maintain selected comfort level Every 10 15 minute the heater turns on and runs for a minute V Press the Power Button to Turn on the Heater V Set heater upright on a level surface V Follow reset instructions listed in thi
10. ith the FrostProted Setting CLEANING MAINTENANCE Always igl the heater before cleaning and allow the heater to coo own 1 Clean the unit with a soft cloth moistened with a mild 3 soap and water solution NEVER use abrasive or flammable solvents fo clean the unit After cleaning be sure to completely dry the unit with a cloth or tovel Store heater in a cool dry location It is recommended that you store the unit in its original carton TIP Over time dust may accumulate on the front grills Tr t be removed by wiping the unit with a damp cloth AUTO SAFETY SHUT OFF This heater is equipped with a technologically advanced safety system that requires the user to reset the heater if there is a potential overheat situation When a potential overheat temperature is reached the system will automatically shut the heater off It can only resume operation when the user resets the unit If the heater shuts down and the Power Light is flashing 1 Stand the heater upright 2 Unplug the heater ak allow 30 minutes for the heater to cool down 3 After 30 minutes plug the heater in and operate normally 4 If the heater does not work normally repeat steps 1 2 and 3 again NOTE If the heater is plugged in again and Power On Off Button is pressed within the 30 minute cool down period heater will run at Max Heat setting but shut down in 2 seconds with the Power Light flashing Please repeat the above 4 steps to reset the h
11. not less than 1875 watts If the heater will not operate see specific instructions on Auto Safety Shut off DO NOT attempt to repair or adjust any electrical or mechanical functions on this unit Doing so will void your warranty The inside of the unit contains no user serviceable parts All servicing should be performed by al personnel only 9 Discontinue use if plug or outlet is hot It is recommended that the outlet be replaced if plug or outlet is hot to touch 20 The heater must not be located immediately below a socket outlet Do not use this heater in the immediate surroundings of a bath a shower or a swimming pool 21 CAUTION In order fo avoid a hazard due to inadvertent resetting of the thermal cutout this appliance must not supplied through an external switching device such as a timer or connected to a circuit that is regularly switched on and off by the utility 22 WARNING In order to avoid overheating do not cover the heater reverse the plug polarized outlet am one it sti install the proper outlet DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS SAFETY FEATURE IN ANY WAY THIS APPLIANCE HAS A POLARIZED PLUG one blade is wider than the other To reduce the risk of electric shock this plug is intended to fit in a way If the plug does not fit fully in the outlet ll does not fit contact a qualified electrician to 23 WARNING This heater is not equipped with a
12. ory it will remember the last temperature settin berns the heater is turned off However if the heater is i the digital thermostat will no longer remember the previous temperature setting You will need to reset the digital thermostat if the heater is unplugged Xas Oscillation if applicable Press the Oscillation Button s on control panel or remote control if applicable to activate or stop the oscillation feature NOTE Please do not manually turn the heater on the base It is designed to turn only by motorized oscillation 3 Timer if applicable Some models are equipped with 24 Hour Auto Shut off Timer feature This allows you to program your heater to shut off automatically after running a defined time interval from 0 to 24 hours l 3 Press the Timer Button C2 once The indicator light will begin to blink for 5 seconds The LCD Display will show 0 and the Hr icon Turn the Dial Wheel on the control panel to adjust from 0 to 24 to select your desired time interval for the heater to shut off automatically The selected hour will pent on the LCD Display and then the Timer indicator light will stop blinking in 3 seconds to indicate that the eded timer is activated The LCD Display will return to show the preset temperature and mode setting To cancel the Timer feature press the Timer Button C3 twice within 5 seconds the Timer indicator light will go off NOTE The timer does not work w
13. s manual V Ensure plug is properly inserted Make sure electrical outlet and circuit breaker are working V Have outlet replaced by a licensed cain V Turn the Dial Wheel right to the highest temperature setting V Unplug the heater and remove all obstructions Position your heater 36 inches 0 9 m away from all objects V Make sure no other high wattage appliances are openi on the same circuit and reset breaker if needed V Follow Auto Safety Shut off instructions to reset the heater and allow sufficient time for the heater to cool down before plugging in again V Set heater upright on a level surface V Change setting to Max V Turn the Dial Wheel right to the highest temperature setting V To make this occur less frequently turn the Dial Wheel right to the highest setting V This is normal operation to ensure the heater is maintaining the room temp accurately Troubleshooting for your Heater Trouble Probable Cause Ooo Soio O Remote if applicable Does not work Heater is Blowing Cold Air Fan Speed Doesn t Change Unexpected Noise Unexpected Smell Battery low Distance too far Control Panel Display dirty When the heater is in Thermostat Mode and reaches the set temperature it will automatically perform a 15 second cool down blowing cold air fo ensure thermostat accuracy Unit is in the Fan Only setting Power Button may have been pressed to turn off the
14. s the button or turn the Dia Wheel to activate The Thermostat icon c will appear on the LCD Display To preset a precise comfort level turn the Dial Wheel to adjust the temperature from 30 C to 18 C Default 30 The LCD Display will show the selected temperature reading When the preset temperature is reached the heater will shut off and cool down for 15 seconds When the room temperature drops below the preset temperature the heater will automatically turn on again to maintain the preset temperature level cm FrostProtect Setting Your heater is equipped with a FrostProtect setting The eater will turn on automatically when the room temperature drops below 5 C To activate FrostProtect setting turn the Dial Wheel to show 5 and the FrostProtect icon 3 will appear on the LCD Display NOTE It is normal for the heater to cycle on and off to maintain the preset temperature Raise the thermostat setting or operate in Stay On mode to prevent the heater from cycling When the preset temperature is reached or when the heater is shut off the fan aliro for 15 seconds without heat This cool down process ensures an accurate and consistent temperature reading NOTE To shut the heater off at any setting press the Power Button C until the LCD Display goes off The heater will cool down for 15 seconds and the Fan Only indicator light will blink in Amber until cool down is completed The digital thermostat has mem
15. ter container Extreme caution is necessary when any heater is used by or near children or invalids and p Paaa the heater is left operating and unattended Always unplug the heater when not in use When P e be sure to pull by the plug and not the cord DO NOT insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire or damage the heater after the heater malfunctions has been dropped or damaged in any manner Return appliance to manufacturer for examination electrical or mechanical adjustment or repair A heater has hot and arcing or sparking parts inside DO NOT use it in areas where gasoline paint or flammable liquids are used or stored Use appliance only for intended household use as described in this manual Any other use not recommended by the manufacturer may cause fire electric shock or injury to persons The use o attachments not recommended or sold by the manufacturer may cause hazards 13 DO NOT use outdoors To prevent a possible fire DO NOT block air intakes or exhaust in any manner DO NOT use on soft surfaces like a bed where openings may become blocked To disconnect heater turn controls to OFF then remove plug from outlet 16 Avoid the use of an extension cord because the extension cord may overheat and cause a risk of fire However it you have to use an extension cord the cor shall be No 14 AWG minimum size and rated
16. the equipment when it is not eing used for an extended period of time e Remove the used battery promptly e Do not discard used batteries into household trash containers Contact your local government for disposal or recycling practices in your area This Class B digital apparatus complies with Canadian ICES 003 OPERATING INSTRUCTIONS 1 Place heater on a firm level surface 2 Plug heater into a standard outlet Once plugged in the Power Light will illuminate NOTE Avoid overloading your circuit by not using other high wattage appliances in the same outlet At 1500 watts this unit a 12 5 Amps 3 Operate heater by pressing the Power Button and selecting modes and settings according to preference NOTE Remove the plastic film from the control panel before using if included Power On Off Press the Power On Off Button to turn the heater on Once on the heater will run in the Max Heat mode and the Sta On icon will appear on the LCD Display Press the Power On Off button to manually turn off the heater at any setting NOTE The Power Light will remain illuminated while unit is plugged in Mode Selection Select your desired heat settings by pressing the corresponding buttons as located on your heater or press the Mode button on remote control if applicable to a through the heat settings An indicator light will illuminate next to each button to indicate that the selected setting mode is activated N
17. urther the warranty does not cover Acts of God such as fire flood hurricanes and tornadoes What are the limits on JCS s Liability JCS shall not be liable for any incidental or consequential damages caused by the breach of any express implied or statutory warranty or condition Except to the extent prohibited by applicable law any implied warranty or condition of merchantability or fitness for a particular purpose is limited in duration to the duration of the above warranty JCS disclaims all other warranties conditions or representations express implied statutory or otherwise JCS shall not be liable for any damages of any kind resulting from the purchase use or misuse of or ibi to use the product including incidental special consequential or similar damages or loss of profits or for any breach of contract fundamental or otherwise or for any claim brought against purchaser by any other party Some provinces states or jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts so the above limitations or exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights that vary from province to province state to state or jurisdiction to jurisdiction How to Obtain Warranty Service In the U S A If you have any question regarding this warranty or would like to obtain warranty service please
Download Pdf Manuals
Related Search
BCH9212 CN