MODEL 94 NUMBERING & LETTERING PRESS
Contents
1. CUIS TAE COST OF STAREAEAG AAS NUMBERALL STAMP amp TOOL CO INC USER MANUAL amp PARTS LIST 70 1 32 1 8 Characters S N P O BOX 187 1 HIGH ST www numberall com TEL 207 876 3541 SANGERVILLE ME 04479 office numberall com FAX 207 876 3566 MODEL 70 NON AUTOMATIC MULTI WHEEL HEAD for 1 32 1 8 Characters Operating Instructions for Hand Shank Models 1 CAUTION ALWAYS WEAR SAFETY GLASSES WHEN STRIKING SHANK WITH A HAMMER BLOW DO NOT DROP OR ABUSE THE MODEL 70 Carelessness could damage the retaining pawls or retaining pawl spring Always lay the unit on its front side with the retaining pawl spring facing up The wheels are rotated by means of a spanner wrench The raised base of each character pad provides a step for the spanner wrench to grab The Model 70 wheels can be rotated in either direction When rotating the wheels to a new character make sure the retaining pawl is in the detent position The front of the Model 70 is the side on which the Numberall logo is stamped This side should be toward the operator when stamping After aligning the Model 70 with your work strike the shank with a hammer blow The size of the hammer and the force of the blow control the depth of impression LIGHTLY LUBRICATE THE MODEL 70 Keep the wheels and parts free from dirt and grit The clearances are very tight and accumulated dirt grit or oil may bind2. the machine On Model 70 machines with the wheels indexed for direct sight reading the stamped character sequence can be read by reading the sequence that is depicted by the arrows that are stamped on the frame The arrows point towards characters that will do the stamping This is the sequence that is to be stamped The arrows are located so that a person sitting down can read the indexing correctly Operating Instructions for Press Models 1 When inserting the Model 70P in the press make sure the frame bears the load The shank should serve only to locate the Model 70P and keep it from falling out No load should bear on the shank Revision 2 0 2 3 The front of the Model 70P is the side with the Numberall logo stamped on it This should be facing the operator or towards the front of the press depending on the orientation of the work to be stamped Follow the following instructions listed above Steps 2 3 4 7 and 8 Disassembly Instructions 1 When ordering parts or requesting information ALWAYS refer to the numbering head s serial number stamped on the right hand side of the frame Select a clean bench that is free of dirt and grit to disassemble the Model 70 Remove the pawl block machine screws 70 125 16 on the back of the unit Then remove the pawl block cover plate 70 125 15 Remove the retaining pawl spring 70 125 17 When removing mark the outside of the spring so that it is not re as
3. ng Element 70 125 29 Cord amp Switch 70 125 30 Coil Spring Protector 70 125 37 Spanner Wrench ALWAYS SPECIFY SERIAL NUMBER WHEN ORDERING PARTS am Numberall Stamp amp Tool Co Inc For extra copies of this manual please call or visit our website P O BOX 187 1 HIGH ST www numberall com TEL 207 876 3541 SANGERVILLE ME 04479 office numberall com FAX 207 876 3566
4. nsion on the retaining pawl will be reduced Factory trained personnel can easily replace retaining pawls so it is recommended that the numbering head be returned for service if you have difficulty with this process Assembly Instructions 1 Make sure the surfaces of the character wheels and parts are clean USE A LIGHT LUBRICANT Start the wheel shaft 70 125 3 into the right hand side of the frame 70 125 1 For models with only one wheel shaft set screw 70 125 7 make sure the proper end of the wheel shaft is started first Slide the wheel shaft part way into the frame opening Beginning with the side washer 70 125 10 push the washer and then the wheels in the original order onto the wheel shaft The index plate side of the wheels should be against the side washer After all of the wheels are in place push the wheel shaft further left until it protrudes from the frame Tighten the wheel shaft set screw s onto the wheel shaft flats Make sure the flats are square with the set screw ends Turn the numbering head over with the pawl block mill cut facing up and the frame legs facing toward the operator Place the pawl block 70 125 14 with the retaining pawls and shaft in place into the mill cut The semi circular ends of the retaining pawls should be facing down Make sure each retaining pawl 70 125 12 rests in its own slot Place the retaining pawl spring 70 125 17 over the pawls so that the spring tines a
5. re centered above each pawl the marked side of the spring should be facing out Place the pawl block cover plate 70 125 15 over the spring and evenly tighten the pawl block screws 70 125 16 Make sure the pawl block is seated in the mill cut Revision 2 0 10 After tightening the machine screws rotate each wheel Every wheel should positively indent without any binding or rocking Recommended Spare Parts e 1 Side Washer 70 125 10 e 2 Retaining Pawls 70 125 12 e 1 Retaining Pawl Spring 70 125 17 e 1 Spanner Wrench 70 125 37 e Spare Wheels should also be stocked depending on use and material being stamped Revision 2 0 NUMBERALL STAMP amp TOOL CO INC BOX 187 HIGH ST SANGERVILLE ME 04479 207 876 3541 FAX 207 876 3566 Model 70 Numbering Machine PARTS LIST A 70 125 17 70 125 15 70 125 37 70 125 14 Ta 2 70 125 1 Modei 70 Numbering Machine PARTS LIST For 1 32 Through 1 8 Character Sizes 70 125 1 Frame 70 125 3 Wheel shaft standard 70 125 4 Wheel shaft hollow for hot stamping 70 125 6 Wheel shaft set screw 70 125 10 Side Washer 70 125 12 Retaining Pawis 70 125 13 Retaining Paw Shaft 70 125 14 Pawl Block 70 125 15 Pawl Block Cover Plate 70 125 16 Pawl Block Cover Plate Screws 2 required 70 125 17 Retaining Pawl Spring 70 125 18 Wheels refer to price list 70 125 22 Blank Spacers 70 125 26 Hot Stamping Equipment 70 125 28 Heati
6. sembled incorrectly Remove the pawl block 70 125 14 Remove the wheel shaft set screw s 70 125 7 Push the wheel shaft 70 125 3 out of the frame 70 125 1 Only use a soft material such as brass to push on the shaft Maintain a record of the wheel order for re assembly Replacing Retaining Pawls 1 2 Disassemble the marking head as per above Disassembly Instructions Using the flat of the spanner wrench carefully push the retaining pawl shaft 70 125 13 and retaining pawls 70 125 12 out of the slot in the pawl block 70 125 14 Do not bend the retaining pawils Maintain the original positioning of the retaining pawls slide the pawls off the shaft Replace the retaining pawls as necessary and slip all of the retaining pawls onto the shaft in the original order Align the retaining pawls on the shaft so that they drop into the milled slots Position the shaft left and right so it clears the screw holes Press the retaining pawl shaft into its slot until it bottoms The shaft must rest on the bottom of the slot Revision 2 0 7 On rare occasions when a new retaining pawl is combined with a used wheel a very slight misalignment of the wheel relative to the other wheels can occur This can be corrected by honing the radius of the pawl The radius of the pawl must remain unchanged while the center of the radius is moved slightly Care must be exercised not to remove too much metal otherwise the spring te
Download Pdf Manuals
Related Search