Maintenance manual
Contents
1. 1 Hook the actuator plate in below and lift it up 159 Perform commissioning after repair Carry out function test after repair Repair The procedure is the same for the Geberit Sigma concealed cistern 8 cm and 12 cm 1 Release the actuator plate 4 Unlock the mounting frame NL Ht i sL0c 90 LOO OS8r7Sd D54850 001 06 2012 La Remove the protection plate Remove the defective lifting device and dispose of it appropriately Il sli lifting device 9 Remove the sticker from the new M GEBERIT 11 Insert the protection plate Repair 21 Repair ae Plug in the plug to the right female sockets ma Lock the mounting frame ee __ La 7 16 Hook the actuator plate in below and lift it up H i TTI Ar h hei a iyi 1 JI hl i e it a ke 15 oS a Perform commissioning after repair Carry out function test after repair E GEBERIT sL0c 90 LOO OS8r7Sd D54850 001 06 2012 Repair Move at least 2 m away from the actuator plate Enter the proximity detection range the actuator buttons start to light up As soon as the control has detected the environment the actuator buttons flash three times Hold your hand in front of the long actuator button on the left A large fl2. approx 5 cm After a few seconds both actuator buttons begin to flash After a few more seconds the actuator buttons flash red three times and then turn blue Remove your hands now Cover the actuator button on the left with your hand until it lights up orange The actuator button on the right flashes Cover the actuator button on the left with your hand again until it lights up yellow The actuator button on the right flashes repeatedly to show the current setting 1 or 2 flashing once setting 1 flashing twice setting 2 Result The setting mode for the automatic flush actuation is now set Cover the actuator button on the right repeatedly until the desired setting has been made Each time the sensor is covered the WC flush control changes between the two settings 1 2 1 2 x Sa belasan X Cover both actuator buttons at the same time with your hands at a distance of approx 5 cm until both actuator buttons flash once Result The desired setting is now saved The WC flush control is ready for operation again E Resetting to factory setting The settings B C and D are reset to the factory setting see Overview Prerequisites The WC flush control is ready for operation gt Cover the actuator button on the left for half a minute until both actuator buttons light up red A flush is triggered Result The factory settings are restored M GEBERIT cL0c 90 L
3. or material damage EN Refers to important information oF Safety notes Repairs may only be carried out by a skilled person using original spare parts and accessories Do not modify the Geberit actuator plate Sigma80 or add any additional modules Product assignment This document describes the maintenance of the following Geberit products 116 090 xx 1 Geberit WC flush control electronic mains operation dual flush actuator plate Sigma80 touchless 116 091 xx 1 Geberit WC flush control electronic mains operation dual flush actuator plate Sigma80 touchless M GEBERIT cL0c 90 LOO OS8rSd D54850 001 06 2012 Functional principle Functional principle Several IR sensors are located behind the glass plate of the WC flush control These sensors scan different detection ranges The distances of the various detection ranges are not precisely defined it depends on how strongly the infrared light is reflected on the respective object piece of clothing etc The proximity detection range A scans a wide range As soon as a person crosses the threshold of this detection range the actuator buttons start to light up and thereby signal that the WO flush control is ready for operation The user detection range B measures whether a user is sitting or standing in front of the WC flush control No objects wall curtain etc should be permanently placed in this area If a sitting user is detected the manual flush actu
4. up orange The actuator button on the right flashes repeatedly to show the current setting flashing once setting 1 flashing twice setting 2 flashing three times setting 3 Result The setting mode for the actuator button illumination is now set E GEBERIT Manual settings Cover the actuator button on the right repeatedly until the desired setting has been made Each time you cover the sensors the WC flush control jumps to the next setting 1 2 3 1 2 3 Cover both actuator buttons at the same time with your hands at a distance of approx 5 cm until both actuator buttons flash once Pi Result The desired setting is now saved The WC flush control is ready for operation again 13 Manual settings D Activating or deactivating the automatic flush actuation When the automatic flush actuation is activated the WC flush control always activates a flush when you step back Manual actuation is not necessary Setting 1 deactivated Setting 2 activated Prerequisites The WC flush control is ready for operation 14 If the actuator buttons are not covered at the same time a flush will be activated Remove your hands and repeat the procedure If you approach the actuator plate too closely with your body it will become inactive and no settings are possible Cover the actuator plate with your arms extended Cover both actuator buttons at the same time with your hands at a distance of
5. M GEBERIT Instandhaltungsanleitung Manuel d entretien Istruzioni per la manutenzione KNOW HOW INSTALLED Table of Content Table of Content Table ONE asn TE A am Ma mi mn eet Dana mani deg ne ett te pn EEE erases dered ana senada mean EE men oat gels banana san pan 2 UI EL A ace Nee i 2 ae a 2 CARO RI 2 ON ee aa an ne ee Wana an aa Ane east jab 2 Panen ena ae 3 SUI RR hi hb nan BA Ian an alan ences et Daan 4 TT VS NON lee ee melon ba bra bae ob aer ena an year ee 5 Settings USING the Geberit Service Fandy asien ee ee be naa ne 6 Lidia rai 11 A Activating or deactivating the cleaning fuNnction oo oo Woo nenn nennn nenn ma 12 B Selecting the light colour of the actuator Bultens an een ee 12 CE Setting the actuator BUONA LUMIA ria ee einen ern ee 13 D Activating or deactivating the automatic flush ACTUATION an 14 E Resetiing to factory SHINGO piena 14 CORRI ZA 15 Cleaning the AURON PIE lalla 15 REL i AEE een E PEA E RE E T E T A E E EE E E AAT 16 Replacing the actuator plate oem see on anne ena ena ee 16 Replacing WAS MOUNTING Taerar 17 Menpan el ag VICE litio aa laen oa setetes ES 20 an e an Nan Maan 23 nenen een 23 Bie ee e PAE E AA en ee De en 25 Target group This document is intended for use by skilled persons as defined by EN IEC 62079 2001 Explanation of symbols Symbol Meaning i CAUTION Refers to a potentially dangerous situation that may cause slight or moderate injury
6. OO OS8rSd D54850 001 06 2012 Care CAUTION i N Aggressive and scouring cleaning agents can damage the surface ASA Never use aggressive cleaning agents that contain chlorine or are acidic abrasive or corrosive gt Clean the actuator plate with mild cleaning agents and water gt Use a soft cloth Geberit recommends the Geberit AguaClean cleaning set article number 242 547 00 1 for cleaning the actuator plate M GEBERIT 15 Repair 4 Attach the plug to the new actuator plate Release the actuator plate 4 Pull out both plugs from the actuator plate and dispose of the defective actuator plate appropriately u E GEBERIT sL0c 90 LOO OS8r7Sd D54850 001 06 2012 Repair 6 Hook the actuator plate in below and lift it up Release the actuator plate x fica il a Ta EA Remove the actuator plate Perform commissioning after repair Carry out function test after repair M GEBERIT 17 Repair bolts 1 1 i Leite ey 4 CT e Nene ri ni Remove the defective mounting frame and dispose of it appropriately Di M GEBERIT 7 Insert the new mounting frame and lock the distance sL0c 90 LOO OS8r7Sd D54850 001 06 2012 9 Attach the plug to the actuator plate MGEBERIT 10 Plug in the plug to the right female sockets Repair
7. a from a distance of 20 to 30 cm Een The Geberit Service Handy must be set to bidirectional mode Operating Geberit Sigma80 with the Geberit Service Handy Information given in corresponds to the text displayed on the Geberit Service Handy display Information given in lt gt refers to buttons on the Geberit Service Handy Commands Menu item Description Application EN DE 20 Release full flush volume For function tests of the lifting FullFlush Releases a full flush device VollMenge 21 Release partial flush volume For function tests of the lifting PartFlush Releases a partial flush device TeilMenge 22 Check detection range For problems with detection RangeTest The flush control makes the individual TestErfas detection ranges of the IR sensors visible in order to check their function Each detection range is indicated by a different light colour The boundary of the detection range must be crossed in order to check its function No flush is released in this process After 10 minutes this function automatically deactivates O Function is deactivated 1 Only the sensors for the proximity detection range are activated Blue Person is detected 2 Only the sensors for the user detection range are activated Blue User is detected Turquoise Standing user is detected Magenta Seated user is detected 3 Only the sensors for the manual flush detection range are activated Magenta Hand is d
8. aning Allows the user to manually start the cleaning program Turning off the program simultaneously blocks the setting mode under the menu item 34 Sett En Sett En Activate setting mode Blocks or allows the end user to change settings in accordance with the user manual M GEBERIT Settings using the Geberit Service Handy Application In the event of detection malfunctions In the event of malfunctions Application Hygiene a Releasing the central flush b Function confirmation Wets the ceramic appliance before use to reduce deposits Prerequisite for starting the manual cleaning function If the program is turned off the settings cannot be unintentionally changed Adjustment range Factory setting Start lt OK gt Start lt OK gt confirm with Rs lt OK gt Adjustment range Factory setting On ON OFF Off OFF On ON OFF Off OFF On ON OFF Off OFF On ON ON Off OFF On ON ON Off OFF Settings using the Geberit Service Handy Parameters Menu item EN DE 40 T LightOn T LightOn 41 DetectT VerweilZ 42 RunOnTime NachlaufZ 43 DelayTime Sp lverz l 44 Fish Time Sp lzeit 45 IntervalT IntervalZ 46 CleanTime ReiniZeit 47 RngPresen RngPresen 48 RngManual RngManual 49 CeramSize CeramSize 50 LightMode LightMode Description Detectio
9. atically deactivated after 3 min Cleaning can now be performed Observe the care instruction in this user manual Cover both actuator buttons at the same time with your hands at a distance of approx 5 cm to deactivate the cleaning function The flashing stops after a few seconds Remove your hands now Result The cleaning function is deactivated The WC flush control is ready for operation again B Selecting the light colour of the actuator buttons The following light colours can be selected Blue turguoise magenta orange yellow Prereguisites The WC flush control is ready for operation If the actuator buttons are not covered at the same time aflush will be activated Remove your hands and repeat the procedure If you approach the actuator plate too closely with your body it will become inactive and no settings are possible Cover the actuator plate with your arms extended Cover both actuator buttons at the same time with your hands at a distance of approx 5 cm After a few seconds both actuator buttons begin to flash After a few more seconds the actuator buttons flash red three times and then turn blue Remove your hands now Result The setting mode for the light colour of the actuator buttons is now set Hold your hand in front of the right actuator button The next light colour appears on both actuator buttons Place your hand in front of the actuator button on the right repeatedly until th
10. ation is deactivated This prevents a flush from being inadvertently activated if the user leans back during use If someone s hand crosses the threshold of the manual flush detection range C the WC flush control activates a small or large flush Manual flush actuation is only possible when a person is in the proximity detection range A e 5 15 cm ja 100 cm Ae 150 cm gt Detection ranges A Proximity detection range B User detection range C Manual flush detection range E GEBERIT 3 Structure Structure 1 Lifting device for Geberit Sigma concealed cistern 8 cm 2 Lifting device for Geberit Sigma concealed cistern 12 cm 3 Mounting frame 4 Geberit actuator plate Sigma80 5 Power supply unit 6 Mains connection cable for external push button M GEBERIT cL06 90 LOO OS8r7Sd D54850 001 06 2012 Troubleshooting Malfunction The actuator buttons are flashing red When you approach the WC the actuator button illumination comes on but the flush does not work When you approach the WC the actuator button illumination does not come on and the flush does not work When you approach the WC the actuator button illumination does not come on but the flush works The actuator button illumination does not go off when you step away stays on for more than 15 minutes Incorrect flushes too soon too late unwanted A flush is triggered when you step back from the WC with
11. e desired light colour is displayed Cover both actuator buttons at the same time with your hands at a distance of approx 5 cm until both actuator buttons flash once Result The desired light colour is now saved The WC flush control is ready for operation again M GEBERIT cL0c 90 LOO OS8rSd D54850 001 06 2012 C Setting the actuator button illumination Three different settings are possible 1 The actuator button illumination always remains off and does not come on even when you approach the WO 2 The actuator button illumination always remains on even when you step back from the WC and leave the room 3 The actuator button illumination comes on as soon as you approach the WC and goes off again when you step back Prereguisites The WC flush control is ready for operation If the actuator buttons are not covered at the same i time a flush will be activated Remove your hands and repeat the procedure A If you approach the actuator plate too closely with l your body it will become inactive and no settings are s4 possible Cover the actuator plate with your arms extended 1 Cover both actuator buttons at the same time with your hands at a distance of approx 5 cm After a few seconds both actuator buttons begin to flash After a few more seconds the actuator buttons flash red three times and then turn blue Remove your hands now 2 Cover the actuator button on the left with your hand until it lights
12. etected 4 For internal test purposes 28 Activate cleaning function Actuator plate and WC can be CleanMode Flush control is inactive for the interval of cleaned without releasing a Reinigung the value entered from menu item flush 46 CleanTime ReiniZeit Can also be stopped manually Adjustment range Factory setting Start lt OK gt Start lt OK gt 0 4 O 0 Start lt OK gt M GEBERIT cL06 90 LOO OS8rSd D54850 001 06 2012 Commands Menu item EN DE 24 BlocFlush Blockiere 25 FactrySet Werkeinst Programs Menu item EN DE 30 AutFlshEn AutFlshEn 31 PowOnfrlsh NetzEinSp 32 PreFlush Vorsp lng 33 CleanEn FreiReini 34 SettEn SettEn Description Block flush No flush is released Function is cancelled upon re establishing connection with the Geberit Service Handy The function switches off automatically after 10 hours Factory settings All programs and parameters are reset to factory settings Description Enable automatic flush If this function is set the control always releases a flush when the user steps back from the WC Manual flush actuation is no longer necessary Select power on flush If the mains voltage is on a flush is released by the flush control Select pre flush The flush control releases a partial flush when a user steps into the user detection range Enable cle
13. he article number of the WC flush control The last two numbers Modell Nr indicate the revision status of the flush control e g 12345601 article number 123 456 xx x revision status 01 11 Software version SWVersion Indicates the software version of the flush control e g 2 version 2 SWVersion 12 Serial number SerialNo Indicates the serial number of the flush control Serien Nr 13 Manufacturing date of the flush control ManufDate Indicates the manufacturing date of the flush control e g 1201 January 2012 ProdDatum 10 M GEBERIT cL0c 90 LOO OS8rSd D54850 001 06 2012 Manual settings Manual settings With the Geberit WC flush control with the Geberit Sigma80 actuator plate specific settings can be made The instructions can be found on the following pages Overview Setting A Activate or deactivate the cleaning function B Select the light colour of the actuator buttons C Set the actuator button illumination D Activate or deactivate automatic flush actuation E Reset to factory setting M GEBERIT Description Factory setting The actuator plate and the WC can be cleaned without triggering a flush The cleaning function can be activated and then deactivated again following completion of the cleaning function The cleaning function is automatically deactivated after 3 min The following light colours can be selected Blue Blue turquoise magenta orange yellow T
14. hree different settings are possible Setting 3 1 The actuator button illumination always remains off and does not come on even when you approach the WC 2 The actuator button illumination always remains on even when you step back from the WC and leave the room 3 The actuator button illumination comes on as soon as you approach the WC and goes off again when you step back When the automatic flush actuation is activated the WC flush control Setting 1 always activates a long flush when you step back after use Manual actuation is not necessary Setting 1 deactivated Setting 2 activated The settings B C and D are reset to the factory setting 11 Manual settings A Activating or deactivating the cleaning function The actuator plate and the WC can be cleaned without triggering a flush Prereguisites The WC flush control is ready for operation Ta J 12 2 3 u a If the actuator buttons are not covered at the same time aflush will be activated Remove your hands and repeat the procedure If you approach the actuator plate too closely with your body it will become inactive and no settings are possible Cover the actuator plate with your arms extended Cover both actuator buttons at the same time with your hands at a distance of approx 5 cm After a few seconds both actuator buttons begin to flash Remove your hands now Result The cleaning function is now active The cleaning function is autom
15. n time until light goes on Length of time during which a person must remain in the proximity detection range for the actuator button illumination to switch on Set detection time Minimum time a person must remain within the user detection range in order to be recognised as a standing or seated user Only relevant if automatic flush actuation is switched on Set run on time The actuator button illumination remains lighted for the length of time entered after the user has left the proximity detection range Set flush delay After the user has left the user detection range the set time interval elapses before a flush is released Only relevant if automatic flush actuation is switched on Set flush time The flush volume of the partial flush can be set The specified flush volumes are reference values Set flush interval interval flush The control automatically releases a full flush after the interval entered The interval is restarted with every flush Set cleaning time Defines the inactive interval of the flush control when the menu item 23 CleanMode Reinigung or the manual cleaning function is started Set proximity detection range Defines the distance at which a person is detected The actuator button illumination turns on when a person is detected Set manual flush detection range Affects the distance at which a hand is detected for flush actuation Specify size of WC ceramic appliance Relevant fo
16. otal number days of operation Days Displays the number of days of operation since commissioning SumBetrT 61 Number of uses total Uses Displays the number of uses since commissioning SumBenut 62 Number of flushes total Flushes Displays the number of flushes since commissioning SumSp l 63 Number of full flushes total FullFlsh Displays the number of full flushes since commissioning SumVoIlIM 64 Number of partial flushes total PartFIsh Displays the number of partial flushes since commissioning SumTeilM 65 Number of automatic flushes total AutFlush Displays the number of automatic flushes since commissioning SumAutSp 66 Number of manual flushes total ManFlush Displays the number of manual flushes since commissioning SumManSp 67 Total number of interval flushes IntFlush Displays the number of interval flushes since commissioning SumIntSp 68 Total number of pre flushes PreFlush Displays the number of pre flushes since commissioning SumVorSp M GEBERIT Adjustment range Factory setting 0 4 O 0 O Blue 1 Turquoise 2 Magenta 3 Orange 4 Yellow Output days uses flushes flushes flushes flushes flushes flushes flushes Settings using the Geberit Service Handy Unit info Menu item Description Output EN DE 10 Type number TypeNo Displays the first six digits of t
17. out manual actuation Water is running continuously into the WC ceramic appliance The WC ceramic appliance is not being flushed out properly M GEBERIT Possible cause The WC flush control waits until all objects tools people curtain etc are outside of the user detection range The teach in process for the surrounding area then begins Software fault The actuator plate is dirty The plug of the lifting device is not plugged in correctly The lifting device is defective Power failure The power supply unit is defective green LED on the power supply unit does not light The plug of the power supply unit on the control is not plugged in correctly Software fault The control is defective The actuator button illumination for the user detection is deactivated The actuator button illumination for the user detection is activated An object is located within the 1 m measuring zone in front of the actuator plate A new object is located within the 1 5 m detection distance around the actuator plate The actuator plate is dirty or damp The actuator plate is scratched Automatic flush actuation is activated Software fault Flat gasket for flush valve inside cistern is defective Filling valve in the cistern is defective The flush volumes are set incorrectly Troubleshooting Fault clearance Remove objects from the user detection range Interrupt the power supply mains fuse for 60 min Clean the act
18. r detection of seated user Set light mode O The actuator button illumination always remains off and does not come on even when a person approaches the WC 1 The actuator button illumination always remains on even when a person steps back from the WC and leaves the room 2 The actuator button illumination turns on when a person approaches the WC and turns off when the person leaves Application A longer duration prevents the button illumination from switching on when a person walks by Prevents flushes due to unintentional entry of a person into the user detection range Optimum flushing of the WC ceramic appliance a Filling the trap for low usage frequency b Flushing out standing water to prevent stagnation Adjustment range Factory setting 1 30 Te053 10 5 08 30 15 05 1 60 s 1 20 s 1 15 s 0 4 062 5 22261 414 451 1 168 h O Off 1 30 min 0 4 O close 2 medium 4 far 0 4 O close 2 medium 4 far 0 2 O short 1 medium 2 long 0 2 O Off 1 On 2 Auto 0 5 s 1 3 5 2 3 min 3 M GEBERIT cL0c 90 LOO OS8rSd D54850 001 06 2012 Settings using the Geberit Service Handy Parameters Menu item Description Application EN DE 51 Set colours Color The light colour of the actuator buttons Color can be selected Counters Menu item Description EN DE 60 T
19. uator plate Correctly attach the plug to the control Replace the lifting device Wait until the end of the power failure Replace the power supply unit Correctly attach the plug to the control Interrupt the power supply mains fuse for 60 min Replace the actuator plate and the control Activate the actuator button illumination see Settings Deactivate the actuator button illumination see Settings Remove objects tools people curtain etc from the 1 m measuring zone Wait 15 minutes until the Surrounding area has been reassessed Clean or dry the actuator plate see Care Replace the actuator plate Deactivate the automatic flush actuation see Settings Interrupt the power supply mains fuse for 60 min Replace the flat gasket for flush valve Replace the filling valve Correctly set the full flush volume on the flush valve system Correctly set the partial flush volume with the Geberit Service Handy Settings using the Geberit Service Handy Settings using the Geberit Service Handy The numbers and terms in the column Menu item correspond to what can be seen on the display of the Geberit Service Handy Further information can be found in the operating instructions of the Geberit Service Handy The infrared interface for communication with the Geberit Service Handy is located directly above the short actuator button on the right To make any settings the Geberit Service Handy must be aimed at this are
20. ush volume is actuated Result The WC flush control is in operation M GEBERIT si Repair Hold your hand in front of the short actuator button on the right A small flush volume is actuated Result The WC flush control is working and ready for operation 24 M GEBERIT cL0c 90 LOO OS8rSd D54850 001 06 2012 Disposal Disposal Constituents This product meets the requirements of the directive 2002 95 EC RoHS Restriction of Hazardous Substances in electrical and electronic equipment Disposal In accordance with directive 2002 96 EC WEEE on waste electrical and electronic equipment manufacturers of electrical equipment are obliged to take back old equipment and to dispose of it correctly The symbol indicates that the product cannot be disposed of with non recyclable waste Old equipment should be returned directly to Geberit where it will be disposed of appropriately Please contact your responsible Geberit sales company or visit www geberit com for collection point addresses M GEBERIT a Geberit International AG Schachenstrasse 77 CH 8645 Jona dokumentation geberit com gt www geberit com 965 050 00 0 00 D54850 001 06 2012
Download Pdf Manuals
Related Search